หัวข้อที่ 19 เอกสารแนบ 1-s-24 list of minimum spares
TRANSCRIPT
7/30/2019 19 1-S-24 List of Minimum Spares
http://slidepdf.com/reader/full/-19-1-s-24-list-of-minimum 1/8
GREAT CIRCLE SHIPPING AGENCY LIMITED.Form S-24
(Rev 09/07)
LIST OF MINIMUM SPARES, TOOLS AND INSTRUMENTS
A) INTERNAL COMBUSTION ENGINES FOR PROPELLING
ITEMS SPARE PARTS NUMBERREQUIRED
Mainbearings
Main bearings of shells for one bearing of eachsize and type fitted, complete with shims,bolts and nuts.
1 set
Cylinderliner
Cylinder liner, complete with joint ring andgaskets
1
Cylindercover
Cylinder cover, complete with all valves, jointrings and gaskets
1
Cylinder cover bolts and nuts, for one cylinder 1/2 setCylindervalves
Exhaust valves, complete with casings, seats,springs and other fittings for one cylinder.
2 sets
Air inlet valves, complete with casings, seats,springs and other fittings for one cylinder
1 set
Starting-air valve, complete with casing, seat,springs and other fittings
1
Relief valve, complete with casing, springs andother fittings
1
Fuel valves, complete with casings, springs
and other fittings for one engine.(For engine with three or more fuel valves per cylinder, two fuel valves complete per cylinder and other fuel valves need no casing)
1 set
Connecting rodbearings
Bottom-end bearings or shells of each size andtype fitted, complete with shims, bolts andnuts.
1 set
Top-end bearings or shells for each size andtype fitted, complete with shims, bolts andnuts.
1 set
Pistons Crosshead type: Piston of each type fitted,
complete with piston rod, stuffing box, skirt,rings, studs and nuts
1
Trunk-piston type: Piston of each type fitted,complete with skirt, rings, studs, nuts,gudgeon pin and connecting rod.
1
Pistonrings
Piston rings for one cylinder 1 set
Pistoncooling
Telescopic cooling pipes and fittings orequivalent for one cylinder unit.
1 set
Gear and
chain
Gear-wheel drive: Wheels for the camshaft
drive of one engine.
1 set
forcamshaftdrives
Chain drive: Separate links with pins androllers of each size and type fitted.
6
144773622.doc Page 1 of 5
7/30/2019 19 1-S-24 List of Minimum Spares
http://slidepdf.com/reader/full/-19-1-s-24-list-of-minimum 2/8
GREAT CIRCLE SHIPPING AGENCY LIMITED.Form S-24
(Rev 09/07)
Bearing bushes of each type fitted. 1 setCylinderlubricator
Lubricator, complete, of the largest size, withits driving chain or gear wheels.
144773622.doc Page 2 of 5
7/30/2019 19 1-S-24 List of Minimum Spares
http://slidepdf.com/reader/full/-19-1-s-24-list-of-minimum 3/8
GREAT CIRCLE SHIPPING AGENCY LIMITED.Form S-24
(Rev 09/07)
B) INTERNAL COMBUSTION ENGINES FOR PROPELLING(Continued)
ITEMS SPARE PARTS NUMBERREQUIRED
Fuelinjectionpumps
Fuel injection pump, complete.[When replacement at sea is practicable, acomplete set of working parts for one pump(plunger, sleeve, valves, springs, etc.)]
1
Fuelinjectionpiping
High pressure fuel pipe of each size and shapefitted, complete with couplings
1
Scavengeblowers
(including T/chargers)
Rotors, rotor shafts, bearings, nozzle rings andgear wheels or equivalent working parts if
other types.(See Note 3)
1 set
Scavenging system
Suction and delivery valves for one pump of each type fitted, complete
1 set
Reductionand /
Complete bearing bush of each size fitted inthe gear case assembly.
1 set
orreversinggear
Roller or ball bearing, complete, of each sizefitted in the gear case assembly.
1 set
Notes: 1. The description and number of each spare part in this Table arethose required for one internal combustion engine for propelling.2. In case where the ship is installed with two or more internal
combustion engines of the same type the spare parts are onlyrequired for one engine.
3.The spare parts for scavenge blowers may be omitted where it hasbeen demonstrated, at the builder’s test bench, for one engine of the type concerned, that the engine can be manoeuvredsatisfactorily with one blower out of action. In this case, however,the requisite blanking and blocking arrangements for running withone blower out of action are to be available on board.
B) BOILERS
SPARE PARTS NUMBER REQUIRED
Valves and seats of main feed check valves forone boiler.
1 set
Safety valve spring of each size.(Including superheater safety valve springs)
1
Oil burner nozzles, complete, for one boiler 1 set
Round type water gauge glasses, if fitted
(Including packing)
12
Flat type water gauge glasses 2Flat type water gauge frame 1Smoke tubes and stay tubes 5% of total number of
144773622.doc Page 3 of 5
7/30/2019 19 1-S-24 List of Minimum Spares
http://slidepdf.com/reader/full/-19-1-s-24-list-of-minimum 4/8
GREAT CIRCLE SHIPPING AGENCY LIMITED.Form S-24
(Rev 09/07)
tubes for one boilerWater tubes and superheater tubes 5% of total number of
tubes for one boiler
144773622.doc Page 4 of 5
7/30/2019 19 1-S-24 List of Minimum Spares
http://slidepdf.com/reader/full/-19-1-s-24-list-of-minimum 5/8
GREAT CIRCLE SHIPPING AGENCY LIMITED.Form S-24
(Rev 09/07)
Notes:1.The description and number of each spare part in this Table are
those required for one boiler.2. In case where the ship is installed with two or more boilers of the
same type for the same service, the spare parts are only required
for one boiler, excepting for the following:a) The number of water gauge glasses of round type and flat type
is required to be the number in this Table for each boiler.b) The number of flat type water gauge frames is required to be
one for two boilers.C) AUXILIARY INTERNAL COMBUSTION ENGINES
ITEMS SPARE PARTS NUMBERREQUIRED
Main
bearings
Main bearings or shells of each size and type
fitted, complete with shims, bolts and nuts.
1 set
Cylindervalves
Exhaust valves, complete with casings, seats,springs and other fittings for one cylinder.
2 sets
Air inlet valves, complete with casings, seats,springs and other fittings for one cylinder.
1 set
Starting-air valve, complete with casing, seat,springs and other fittings.
1
Relief valve, complete with casing, springs andother fittings.
1
Fuel valves of each size and type fitted,complete with casings, springs and other
fittings for one cylinder
1/2 set
Connecting rodbearings
Bottom-end bearings or shells of each size andtype fitted, complete with shims, bolts andnuts for one cylinder.
1 set
Top-end bearings or shells of each size andtype fitted, complete with shims, bolts andnuts for one cylinder.
1 set
Trunk piston type: Gudgeon pin with bush forone cylinder.
1 set
Connecting rod complete (on 2 generator
ships)
1 set
Pistonrings
Piston rings, for one cylinder 1 set
Pistoncooling
Telescopic cooling pipes and fittings or theirequivalent for one cylinder.
1 set
Fuelinjectionpumps
Fuel injection pump, complete.[When replacement at sea is practicable, acomplete set of working parts for one pump(plunger, sleeve, valves, springs, etc.)]
1
Fuelinjection
piping
High pressure fuel pipe of each size and shapefitted, complete with couplings
1
Casketsandpacking
Special gaskets and packing of each size andtype fitted, for cylinder cover and cylinderliner for one cylinder.
1 set
144773622.doc Page 5 of 5
7/30/2019 19 1-S-24 List of Minimum Spares
http://slidepdf.com/reader/full/-19-1-s-24-list-of-minimum 6/8
GREAT CIRCLE SHIPPING AGENCY LIMITED.Form S-24
(Rev 09/07)
Notes: 1. The description and number of each spare part in this Table arethose required for one auxiliary internal combustion engine.
2. In case where the ship is installed with two or more internalcombustion engines of the same type for the same service, thespare parts are only required for one engine.
3. In case where the number of generators of adequate capacityinstalled for essential service exceeds the required number, nospare part is required for the auxiliary engines.
D) OTHER MACHINERY
ITEMS SPARE PARTS NUMBERREQUIRED
Shafting Coupling bolts and nuts of each size, completeset
1 set
Main thrust bearings:Pads for one face of Mitchell type thrust block,orComplete thrust shoe for one face of solid ringtype, orInner and outer race with rollers thrustbearings
1 set foreach size1 for eachsize1 for eachsize
Feed and Impeller shaft of feed pump 1condensate watersystem
Impeller shaft of condensate pump(For reciprocating pump, one complete set of calves and springs)
1
Startingair system
Piston rings of each size, for one compressorcylinder.(Including scavenging pump)
1 set
Suction and delivery valves are springs of aircompressor for one cylinder
1/2 set
Coolingwatersystem
Impeller shaft of circulating pump and coolingpump.(For reciprocating pump, one complete set of rod, valves and springs)
1
Fuel oilsystem
Oil transfer pump valves and springs for onepump
1 set
Oil burning pump valves and springs for onepump
1 set
Oil filter wire gauze of each size for one oilburning equipment.
1set
Lubricating oil
system
Lubricating oil pump valves and springs forone pump.
1 set
Bilgesystem
Bilge pump valves and springs for one pump.(These spare parts may be omitted where the parts are of the same type as the parts of
1 set
144773622.doc Page 6 of 5
7/30/2019 19 1-S-24 List of Minimum Spares
http://slidepdf.com/reader/full/-19-1-s-24-list-of-minimum 7/8
GREAT CIRCLE SHIPPING AGENCY LIMITED.Form S-24
(Rev 09/07)
cooling pump)Condenser Condenser tubes. (Including ferrules) 2% of totalNotes: 1. The description and number of each spare part in this Table are
those required for one equipment shown in the Table.2. In case where the ship is installed with two or more equipment,
excepting propulsion shafting , of the same type for the sameservice, the minimum required number of those spare parts is forone of them only.
144773622.doc Page 7 of 5
7/30/2019 19 1-S-24 List of Minimum Spares
http://slidepdf.com/reader/full/-19-1-s-24-list-of-minimum 8/8
GREAT CIRCLE SHIPPING AGENCY LIMITED.Form S-24
(Rev 09/07)
E) LSA – FFA INTERNAL COMBUSTION ENGINES
DESCRIPTION NUMBER REQUIRED
Emergency Fire Pump Engine:
Set of Cylinder valves 2 SetsPiston rings 2 Sets
Main Bearings 1 Set
Piston 1
Connecting rod 1
Life Boat Engine:
Set of Cylinder valves 2 Sets
Piston rings 2 Sets
Main Bearings 1 Set
Piston 1
Connecting rod 1
Emergency Generator / AirCompressor Engine:
Set of Cylinder valves 2 Sets
Piston rings 2 Sets
Main Bearings 1 Set
Piston 1
Connecting rod 1
Smoke / Heat Detector units 1 set
F) POLLUTION PREVENTION EQUIPMENT
DESCRIPTION NUMBER REQUIRED
OILY BILGE SEPARATOR
Coaleser filter Element 1 set
INCINERATOR
Spray Nozzle 1 set
CHIEF ENGINEER’S SIGN .................................. DATE .....................
Notes: This form is to be filled up and verified at least once in 6 months andcopy forwarded to company along with necessary indents if necessary.Remarks to be put against items short, if indents already outstanding. This form is to be filed in C/E's file No.42 (List of minimum spares)
144773622.doc Page 8 of 5