真诚打造信誉·追求更高品位青岛迪维希机械有限公司 · f2f length to en558,iso...

青岛迪维希机械有限公司Qingdao DVC Machinery Co.,LTD

真诚打造信誉·追求更高品位Create Sincere Credit,Go In For Higher Level

Qingdao DVC Machinery Co., Ltd http://www.dvcmachinery.com

T e l :0086 532-83306568Fax:0086 532-83306797Cell: 0086 136 6532 6778Skype: [email protected]: [email protected]

Factory : No.26&28 Tonghui 1 Road, Economic Development Zone of Pingdu Qingdao （266700） Shandong, China

青岛迪维希机械有限公司Qingdao DVC Machinery Co.,LTD

DVC FLUID SCIENCE AND TECHNOLOGY

DVC 流体科技

Who Are We

Qingdao DVC Machinery Co.,LTD is located at Pingdu Industrial development zone in the beautiful

coastal city Qingdao, 60km to Qingdao Airport. Our company was established in 2006 with registered

capital of 30 million RMB and total investment of 60 million RMB, 6000 ㎡ floor area, 320 employees,

and advanced machining and testing equipments.

Our company is dedicated in the manufacturing of valves, hydrants, strainers and pipe fittings which

are qualified by ISO9001, CE SANTARY and WRAS certificates.

CONTENTS

1-12

13

14-19

20-29

30-31

32-34

35

36

37-40

41-46

47-53

54-63

64

Gate Valve 　　　　　　　

Knife Gate Valve

Butterfly Valve

Check Valve

Globe Valve

Air-Release Valve

Hydraulic control Valve

Ball valve

Strainer

Hydrants

Flanged Pipe fittings

Coupling & Joints & Adaptor

Watermeter Box

Qingdao DVC machinery CO.,LTD Email:[email protected] 　　http://www.dvcmachinery.com Tel:0086-532-83306568 Fax:0086-532-83306797 　　 01

Resilient Gate Valves NRS Flanged Ends BS5163 Fig.1113-BS5163 & Fig.1115-SABS664/665

Specification

Design confirms to: BS5163, SABS664/665

Flanged confirms to:EN1092-2 PN10 or PN16,BS4504

F2F Length to EN558,ISO 5752 Basic Series 3.

Test & Inspection: BS6755

Suitable medium: water and neutral liquid

Working temperature: NBR≤80℃ EPDM≤120℃

Operator: Handwheel,Nut,Extension-stem,Gearbox

WRAS Approved

Normal pressure: 1.0MPa, 1.6MPa, 2.5MPa.

Material List

DIMENSIONS

Working Pressure

DNL

H C M D b n-dBS5163/665 BS5150/664

40 165 245 88 110 150 19 4-19

50 178 216 278 102 125 165 19 4-19

65 190 288 122 145 185 19 4-19

80 203 229 310 138 160 200 19 8-19

100 229 254 360 158 180 220 19 8-19

125 254 405 188 210 250 19 8-19

150 267 280 448 212 240 285 19 8-23

200 292 317 550 268 295 340 20 12-23

250 330 356 668 320 355 405 22 12-28

300 356 380 750 378 410 460 24.5 12-28

350 381 470 900 438 470 520 26.5 16-28

400 406 470 1030 490 525 580 28 16-31

450 432 485 1080 532 525 640 30 20-31

500 457 510 1188 610 650 715 31.5 20-34

600 508 600 1380 725 770 840 36 20-37

NO. PART MATERIAL

1 BODY GGG40/GGG50

2 WEDGE GGG40/GGG50+NBR/EPDM

3 STEM NUT BRASS/BRONZE/59-1/CZ132/5-5-5

4 STEM 2Cr13/420/304

5 BONNET GGG40/GGG50

6 GLAND BRASS59-1

7NUT/HANDWHEEL

GGG40/GGG50

(mm)

GATE VALVE


Resilient Gate Valves NRS Flanged Ends DIN F4/F5Fig.1111-DIN3352 F4 & Fig.1112-DIN3352 F5

Specification

Design confirms to: DIN3352

Flanges to DIN2501/EN1092-2 PN10 or PN16

Test & Inspection:DIN3230

Working temperature: NBR≤80℃，EPDM≤120℃

Suitable medium: water and neutral liquid.

Operator:handwheel,nut,extension stem,gearbox

WRAS/CE Approved

Normal pressure:1.0MPa, 1.6MPa, 2.5MPa

Material List

DIMENSIONS

Working Pressure

DNL

H C M D b n-dF4 F5

40 140 240 245 88 110 150 19 4-19

50 150 250 278 102 125 165 19 4-19

65 170 270 288 122 145 185 19 4-19

80 180 280 310 138 160 200 19 8-19

100 190 300 360 158 180 220 19 8-19

125 200 325 405 188 210 250 19 8-19

150 210 350 448 212 240 285 19 8-23

200 230 400 550 268 295 340 20 12-23

250 250 450 668 320 355 405 22 12-28

300 270 500 750 378 410 460 24.5 12-28

350 290 550 900 438 470 520 26.5 16-28

400 310 600 1030 490 525 580 28 16-31

450 330 650 1080 532 585 640 30 20-31

500 350 700 1188 610 650 715 31.5 20-34

600 390 800 1380 725 770 840 36 20-37

700 430 900 1545 793 840 910 38.5 24-37

800 470 1000 1750 900 950 1028 43 24-40

NO. PART MATERIAL

1 BODY GGG40/GGG50

2 WEDGE GGG40/GGG50/NBR/EPDM


4 STEM 2Cr13/420/304


6 GLAND BRASS 59-1

7HAND WHEEL

GGG40/GGG50

(mm)

GATE VALVE

F5F4


Resilient Gate Valves NRS Flanged Ends DIN F4/F5Fig.1161-DIN3352 F4 & Fig.1162-DIN3352 F5

Specification

Design confirms to: DIN3352

Flanges to DIN2501/EN1092-2 PN10 or PN16

Test & Inspection:DIN3230



Operator:handwheel,nut,extension stem,gearbox

WRAS/CE Approved

Normal pressure:1.0MPa, 1.6MPa, 2.5MPa

Material List

Working Pressure

NO. PART MATERIAL

1 BODY GGG40/GGG50

2 WEDGE GGG40/GGG50/NBR/EPDM


4 STEM 2Cr13/420/304


6 GLAND BRASS 59-1

7HAND WHEEL

GGG40/GGG50

GATE VALVE

DIMENSIONS (mm)

DN L F4 LF5 H d1 d2 d3 d4xn ISO Top Flange

50 150 250 198 90 70

20

9x4 F7

65 170 270 232

125 102 11x4 F10

80 180 280 255

100 190 300 290

125 200 325 329

150 210 350 400

200 230 400 475

250 250 450 560

175 140 30 18x4

F14300 270 500 635

350 290 550 720

400 310 600 1055

F16450 330 650 1080

500 350 700 1240

600 390 800 1340


Resilient Gate Valves OS&Y Flanged Ends DINF4/F5/BS5163Fig.1211/1212-DIN3352 F4/F5,Fig.1213-BS5163,Fig.1215-SABS664/665

GATE VALVE

Specification

Design confirms to: DIN3352.BS5163, SABS664/665

Flanged drilled confirms to DIN2501, BS4504

Test& Inspection: DIN3230, BS6755



Operator: hand wheel, nut, extension stem, gear operator

WRAS Approved

Normal pressure: 1.0MPa, 1.6MPa, 2.5MPa.

Material List

DIMENSIONS

Working Pressure

NO. PART MATERIAL

1 BODY GGG40/GGG50



4 STEM 2Cr13/420/304


6 GLAND BRASS59-1

7 Handwheel GGG40/GGG50

(mm)

DNL

H C M D b n-dF4 F5 BS5163/665 BS5150/664

50 150 250 178 216 350 102 125 165 19 4-19

65 170 270 190 370 122 145 185 19 4-19

80 180 280 203 229 380 138 160 200 19 8-19

100 190 300 229 254 405 158 180 220 19 8-19

125 200 325 254 280 455 188 210 250 19 8-19

150 210 350 267 490 212 240 285 19 8-23

200 230 400 292 317 540 268 295 340 20 12-23

250 250 450 330 356 720 320 355 405 22 12-28

300 270 500 356 380 860 378 410 460 24.5 12-28

350 290 550 381 470 1185 438 470 520 26.5 16-28

400 310 600 406 470 1355 490 525 580 28 16-31

450 330 650 432 485 1570 532 525 640 30 20-31

500 350 700 457 510 1830 610 650 715 31.5 20-34

600 390 800 508 600 2010 725 770 840 36 20-37


Resilient Gate Valves NRS/OS&Y Flanged Ends AWWA200/250PSIFig.1114-ANSI C515 NRS & Fig.1214-ANSI C515 OS&Y

Specification

Valves comply with AWWA C509/C515

Available with flanges to EN1092-2 PN10 or PN16,ANSI B16.1 Class125

(Other types available on requested)

Face to Face length in accordance with EN558-1 Basic series3,

ASME B16.10-2000

Available with handwheel or gearbox(level or spur gear box)

Working temperature: -10℃ to 120℃

16bar

Material List

Working Pressure

PART MATERIAL ASTM Spec.

BODY Ductile Iron A536 65-45-12

WEDGE Ductile Iron +EPDM

Stem NUT Brass B16 C36000

STEM Stainless Steel AISI 420

BONNET Ductile Iron A536 65-45-12

GLAND Ductile Iron A536 65-45-12

Gasket EPDM

HAND WHEEL Ductile Iron A536 65-45-12

GATE VALVE

DN L H M D b n-d

1.5" 165 260 98.5 127 15 4-16

2" 178 270 120.5 152 16 4-19

2.5" 190 283 139.5 178 18 4-19

3" 203 311 152.5 191 19 4-19

4" 229 352 190.5 229 24 8-19

5" 254 435 216 254 24 8-22

6" 267 485 241.5 279 25.4 8-22

8" 292 520 298.5 343 28.6 8-22

10" 330 632 362 406 30.2 12-25

12" 356 745 432 483 31.8 12-25

14" 381 835 476 533 35 12-29

16" 406 953 539.5 597 36.5 16-29

18" 432 1050 578 635 40 16-32

20" 457 1160 635 699 43 20-32

24" 508 1395 749.5 813 47.7 20-35

DIMENSIONS (Inch)


Resilient Gate Valves NRSFlanged Ends AWWA200/250/300PSIFig.1164-ANSI C515 NRS & Fig.1264-ANSI C515 OS&Y

GATE VALVE

Specification

Valves comply with AWWA C515

with indicato post flange and a 2" square operating nut

Available with flanges to EN1092-2 PN10 or PN16,

ANSI B16.1 Class125 (Other types available on requested)

Triple O-Ring stem seals

NPT Brass plug on body



200/250/300PSI

Material List

DIMENSIONS

Working Pressure

(Inch)








Gasket EPDM


DN L H M D b n-d

2.5" 190.5 7-1/2" 270 139.5 178 18 4-19

3" 203 8" 296 152.5 191 19 4-19

4" 229 9" 350 190.5 229 24 8-19

5" 254 10" 410 216 254 24 8-22

6" 267 10-1/2" 455 241.5 279 25.4 8-22

8" 292 11-1/2" 545 298.5 343 28.6 8-22

10" 330 13" 645 362 406 30.2 12-25

12" 356 14" 730 432 483 31.8 12-25


AWWA Resilient Gate Valves Push on EndsFig.1234

Specification


Push on Ends: fitted NBR/EPDM sealing gasket

to suit PVC pipe

Suitable medium:water and neutral liquid.

Available with Nut or handwheel or gearbox


Normal pressure: 16bars

Material List

Working Pressure




Stem NUT Brass/Bronze B16C36000/C83600




Gasket EPDM

NUT Ductile Iron A536 65-45-12

GATE VALVE

DIMENSIONS (Inch)

DN L H H1 D A

2" 10.24 12 2.56 2.44 3.43

2.5" 10.75 12.4 2.95 2.99 3.54

3" 12 13.62 3.15 6.58 3.74

4" 13.78 15.55 3.54 4.65 4.21

6" 16.85 20.47 4.53 6.77 5.7

8" 18.5 22.24 6.1 8.74 6.57

10" 21.25 25.5 7.3 11.06 6.7

12" 26.45 29.5 8.3 13.2 9


AWWA Resilient Gate Valve NRS MJ+MJ/MJ+FL200/250PSIFig.1144-MJ+MJ & Fig.11452-FL+MJ

GATE VALVE

Specification


flanges to ,ANSI B16.1 Class125

MJ confirms to:AWWA C153/A21.53



16bar

Material List

DIMENSIONS

Working Pressure

(Inch)








Gasket EPDM


DNL

H M D D’MJ+MJ MJ+FL

2" 235 206.5 240 120.5 152 175

3" 241 222 311 152.5 191 255

4" 254 241.3 352 190.5 229 255

6" 292 279.5 485 241.5 279 305

8" 318 305 520 298.5 343 355

10" 375 352.5 632 362 406 405

12" 378 367 745 432 483 405

MJ+MJ MJ+FL


Resilient Gate Valves NRS Socket endsFig.1122-DIN3352 & Fig.1123-BS5163 & Fig.1125-SABS664/665

Specification

Design confirms to: DIN3352,BS5163, SABS664/665

Face to Face Length to EN558,SABS664.

Test & Inspection: BS6755

Suitable medium: water and neutral liquid


Operator: Handwheel,Nut,Extension-stem,Gearbox

Normal pressure: 1.6MPa

Material List

Working Pressure

GATE VALVE

DIMENSIONS (mm)

DN H L L1 A

50 295 335 88 66

65 299 335 93 79

80 330 335 93 93

100 375 335 110 113

125 456 375 117 127

125 456 375 117 143

150 545 405 135 163

200 570 450 155 203

200 570 450 155 228

250 640 450 155 253

300 790 500 174 318

NO. PART MATERIAL

1 BODY GGG40/GGG50



4 STEM 2Cr13/420/304


6 GLAND BRASS59-1

7NUT/HANDWHEEL

GGG40/GGG50


DN L H G F WEIGHT (KG)

20 122 175 0.75’ 26 3.6

25 127 185 1’ 26 4.1

32 127 190 1.25’ 26 4.6

40 154 235 1.5’ 27 5.2

50 154 242 2’ 31 5.7

NO. PART MATERIAL

1 BODY GGG40/GGG50

2 WEDGE EPDM/NBR

3WEDGE CORE

GGG50/59-1BRASS

4 STEM 2Cr13/420/304

5 THRUST 59-1BRASS

6 SEAL NUT 59-1BRASS

Resilient Gate Valves NRS Flanged Screwed/Threaded EndsFig.1151

GATE VALVE

Specification

DESCRIPTION

1.Design confirms to:DIN3352 Part4

2.Face to Face confirms to:DIN3202

3.Threaded Joint connection :ISO228 female threaded

4.Normal Pressure :1.0Mpa/1.6Mpa

5.Suitable medium: water

6.Working temperature: NBR ≦ 120℃

7.Operator : hand-wheel , nut, extension stem

Material List

DIMENSIONS (mm)


Metal Sealed,NRS & OS&Y Gate ValvesFig.1313-NRS & Fig.1413-OS&Y

Specification

Design confirms to:EN1171-2002,MSS SP-70,BS3464Face to Face Length to EN558-1 basic series 3 andASME B16.10-2000. Flanges to EN1092-2 PN10 or PN16,ANSI B16.1 Class125 (other types available on request.) Working temperature: -10℃ to 120℃

Operator: Handwheel,Gearbox(Bevel or spur gearbox)

16bar for EN1171 valves 200PSI for MSS SP-70,size2"-12" 150PSI for MSS SP-70,size14" and above

Material List

Working Pressure

PART MATERIAL EN Spec. ASTM Spec.

BODY Cast Iron EN-JL1040 ASTM A126 Class B

Body Trim Bronze EN 1982 CC491K ASTM B62 C83600

Wedge Trim Bronze EN 1982 CC491K ASTM B62 C83600

Wedge Cast Iron EN-JL1040 ASTM A126 Class B

Wedge Nut Bronze EN 1982 CC491K ASTM B62 C83600

Stem Stainless Steel BS970 420S37 AISI 420

Bonnet Cast Iron EN-JL1040 ASTM A126 Class B

Gasket Graphite Non-Asbestos non-asbestos

Stuffing Box Cast Iron EN-JL1040 ASTM A126 Class B

Packing Graphite Non-Asbestos non-asbestos

Handwheel Cast Iron EN-JL1040 ASTM A126 Class B

GATE VALVE

DIMENSIONS (mm)

DN LFlange

D M C B b n-d

DN50 178 165 125 102 19 2 4 X Φ19

DN65 191 185 145 122 19 2 4 X Φ19

DN80 203 200 160 132 19 2 8 X Φ19

DN100 229 220 180 156 19 2 8 X Φ19

DN150 267 285 240 211 19 2 8 X Φ23

DN200 292 340 295 266 20 2 12 XΦ23

DN250 330 400 355 319 22 2 12 XΦ28

DN300 356 455 410 370 24.5 3 12 XΦ28

DN350 381 520 470 429 26.5 3 16 XΦ28

DN400 406 580 525 480 28 3 16 XΦ31

DN450 432 640 585 548 30 3 20 XΦ31

DN500 457 715 650 609 31.5 3 20 XΦ34

DN600 508 840 770 720 36 3 20 XΦ37


Metal Sealed,NRS Gate ValvesFig.1311

GATE VALVE

Specification

Design confirms to:DIN3352-F4

Face to Face Length to EN558-1 basic series 14

Flanges to EN1092-2 PN10 or PN6

Operator: Handwheel,Gearbox(Bevel or spur gearbox)


10 bar for valves DN40-DN150 6 bar for valves DN200-DN300 4 bar for valves DN350-DN400

Material List

DIMENSIONS

Working Pressure

(mm)

PART MATERIAL EN Spec.

BODY Cast Iron/DI GGG40

Body Trim Brass CuZn39Pb3

Wedge Trim Brass CuZn39Pb3

Wedge Cast Iron/DI GGG40

Wedge Nut Brass CuZn39Pb3

Stem Stainless Steel X20Cr13

Bonnet Cast Iron/DI GGG40

Gasket EPDM or Graphite

Gland Cast Iron/DI GGG40

Packing Graphite Non-Asbestos

Handwheel Cast Iron/DI GGG40

DN L H C M D B n-d

40 140 245 88 110 150 19 4-19

50 150 278 102 125 165 19 4-19

65 170 288 122 145 185 19 4-19

80 180 310 138 160 200 19 8-19

100 190 360 158 180 220 19 8-19

125 200 405 188 210 250 19 8-19

150 210 448 212 240 285 19 8-23

200 230 550 268 295 340 20 12-23

250 250 668 320 355 405 22 12-28

300 270 750 378 410 460 24.5 12-28

350 290 900 438 470 520 26.5 16-28

400 310 1030 490 525 580 28 16-31


Knife Gate Valves Fig.1511-NRS & 1611-OS&Y

Knife Gate Valve

DESCRIPTION

1.Face to Face :EN558-1.MSS2.Flanged ends:DIN2501,BS4504,ANSIB16.103.Test &inspection:DIN3230 4.Working temperature: NBR ≦ 80℃ ,EPDM≤120℃

5.Operator :hand-wheel, nut, extension stem, gear operator

NO. PART MATERIAL

1 “U”SEAT EPDM/NBR

2 BODY DI,GGG40/50.ASTMA536

3 KNIFE 304/316

4 STEM 420/304

5 COVER DI,GGG40?50.ASTMA536

6 SEAL NUT BRASS

Material List

DIMENSIONS (mm)

DNDN2501 BS10T/D BS10T/E ANSI MSS SP=81

H L L WD N-D D N-D D N-D D N-D

50 125 4-M16 114.3 4-5/8” 114.3 2004/5/8 120.5 4-5/8” 290 43 48 180

65 145 4-M16 146 4-5/8” 146 4-5/8” 139.5 4-5/8” 295 46 48 180

80 160 8-M16 165.1 4-5/8” 165.1 4-5/8” 152.5 4-5/8” 320 46 51 200

100 180 8-M16 177.8 4-5/8” 177.8 8-5/8” 190.5 8-5/8” 365 52 51 300

125 210 8-M16 209.5 8-5/8” 209.5 8-5/8” 216 8-3/4” 405 56 51 250

150 240 8-M16 235 8-5/8” 235 8-3/4” 241.5 8-3/4” 405 56 51 300

200 295 8-M16 292.1 8-5/8” 292.1 8-3/4” 298.5 8-3/4” 478 56 57 350

250 350 12-M20 355.6 8-3/4” 355.6 12-3/4” 362 12-7/8” 692 68 70 400

300 400 12-M20 406.4 12-3/4” 406.4 12.7/8 432 12-7/8” 785 78 76 500

350 460 16-M20 469.9 12-7/8” 469.9 12-7/8” 476 12-1” 892 78 76 500

400 515 16-M24 520.7 12-7/8” 520.7 12-7/8” 539.5 12-1” 998 102 89 600

450 565 20-M24 584.2 12-7/8” 584.2 16-7/8” 578 16-9/8” 1422 114 89 600

500 620 20-M24 641.3 16-7/8” 641.3 12-7/8” 635 20-9/8” 1565 127 114 600

600 725 20-M27 755.6 16-1” 755.6 16-9/8” 20.1.25” 1680 154 114 750

NRS OS&Y


Wafer Butterfly Valve (DN50-DN600 PN16/PN25, Class125/Class250)Fig.2211-DI Disc,2212-S.S304 Disc

Butterfly Valve

Specification Valves comply with EN593, BS5155,MSS SP-67. Replaceable rubber liner for size DN50-DN300. Vulcanized rubber liner for size DN350-DN600. With 4 locating holes for easier installation and centering. Actuator-ready with top-flange in accordance with ISO 5211-1.Handle or gearbox operated. Flanges to EN1092-2 PN10/16,ANSI B16.1 Class125(Other types available on request). WRAS approved.

Working Pressure 16 bar for Size DN50 to DN600 25 bar for Size DN50 to DN300

Working Temperature -10℃ to 120℃ for EPDM liner. -10℃ to 82℃ for NBR liner. -10℃ to 150℃ for Viton liner.

Corrosion Protection Internally and externally liquid epoxy painted or fusion bonded epoxypowder coated (FBE).

PART Materials EN Spec. ASTM Spec.

Body Cast Iron EN-JL 1040 ASTEM A126 Class B

Shaft Stainless Steel BS970 420S37 AISI 420

DiscStainless Steel BS970 304S15 ASTM A351 CF8

Bronze EN1982 CC491K ASTM B62 C83600

Ductile Iron Chrome Plated or FBE coated EN-JS 1050 ASTM A536 65-45-12

Bushing PTFE Commercial Commercial

Liner EPDM/NBR/Viton Commercial Commercial

O-Ring EPDM/NBR/Viton Commercial Commercial

Size 50 65 80 100 125 150 200 250 300 350 400 450 500 600

A 161 175 181 200 215 225 241 296 336 368 400 422 480 562

B 80 91 95 115 134 138 174 198 234 288 315 340 388 450

C 30 30 30 30 30 30 30 30 30 45 45 45 45 45

D 90 90 90 90 90 90 125 125 125 150 175 175 210 210

E 43 45 46 51.5 56 56.5 60 68.5 79.5 78 88 109 127 154

Φ 56.8 71.5 83 101.5 127.8 151.1 200.5 250.8 300.5 335.5 393.5 443.5 500.5 600.8

S×S 11×11 14×14 17×17 22×22 27×27 Φ48

Top Flange F07 F07 F07 F07 F07 F07 F10 F10 F10 F12 F14 F14 F16 F16

Weight(kg) 4.4 5.4 5.6 7.4 10 12.2 16.9 26.3 36.3 66.7 110 130.5 157.3 222

Material List

Dimensions (mm)


Lug Butterfly Valve (DN50-DN600 PN16/PN25, Class125/Class250)Fig.1511-NRS & 1611-OS&Y

Butterfly Valve

Specification Valves comply with EN593, BS5155,MSS SP-67.Replaceable rubber liner for size DN50-DN300.Vulcanized rubber liner for size DN350-DN600. With 4 locating holes for easier installation and centering.Actuator-ready with top-flange in accordance with ISO 5211-1.Handle or gearbox operated. Flanges to EN1092-2 PN10/16,ANSI B16.1 Class125 (Other types available on request). WRAS approved.



Corrosion Protection Internally and externally liquid epoxy painted or fusion bonded epoxypowder coated (FBE). Notes: Ductile Iron body for PN25 or Class250 valves. Design and material are subject to change without notice.


Body Cast Iron EN-JL 1040 ASTEM A126 Class B


DiscStainless Steel BS970 304S15 ASTM A351 CF8

Bronze EN1982 CC491K ASTM B62 C83600

Ductile Iron Chrome Plated or FBE coated EN-JS 1050 ASTM A536 65-45-12

Bushing PTFE Commercial Commercial

Liner EPDM/NBR/Viton Commercial Commercial


Size 50 65 80 100 125 150 200

A 140 152 160 180 191 202 237

B 68 76 85 100 120 132 164

C 30 30 30 30 30 30 30

D 90 90 90 90 90 90 125

E 43 45 46 51.5 56 56.5 60

Φ 56.8 71.5 83 101.5 127.8 151.1 200.5

S×S 11×11 14×14 17×17

Top Flange F07 F07 F07 F07 F07 F07 F10

Weight(kg) 4.6 5.6 5.9 7.7 10 12.5 17.5

Material List

Dimensions (mm)

Size 250 300 350 400 450 500 600

A 274 313 368 400 422 480 562

B 200 230 288 315 344 388 450

C 30 30 45 45 45 45 45

D 125 125 150 175 175 210 210

E 68.5 79.5 78 88 109 127 154

Φ 251.3 300.5 335.5 393.5 443.5 500.5 600.8

S×S 22×22 27×27 Φ48

Top Flange F10 F10 F12 F14 F14 F16 F16

Weight(kg) 28 38 100 120 135 180 233


Grooved Butterfly Valve(DN50-DN300 PN16)Fig.2413

Butterfly Valve

Specification Valves comply with EN593, BS5155,MSS SP-67.

Coated rubber disc.

Actuator-ready with top-flange in accordance with ISO 5211-1.

Handle or gearbox operated.

Groove dimensions comply with Metric or AWWA C606 standard.

Working Pressure 16 bar

Working Temperature -10℃ to 120℃ for EPDM liner.

-10℃ to 82℃ for NBR liner.

-10℃ to 150℃ for Viton liner.

Corrosion Protection Internally and externally fusion bonded epoxy powder coated(FBE).

Notes: Design and material are subject to change without notice.



Body Ductile Iron EN-JS 1050 ASTM A536 65-45-12


Disc

DI EPDM Coated EN-JS 1050 ASTM A536 65-45-12

DI NBR Coated EN-JS 1050 ASTM A536 65-45-12

DI Viton Coated EN-JS 1050 ASTM A536 65-45-12


Size 50 65 80 100 125 150 200 250 300

Pipe OD 60.3 73.0/76.1 88.9 114.3 139.7/141.3 165.1/168.3 219.1 273.0 323.9

A 130 142 147 177 171 213 231 282 306

B 77 85 90 108 120 145 180 230 260

C 30 30 30 30 30 30 30 30 30

D 90 90 90 90.0 90 90.0 125 125 125

E 84 97 97 116 148 148 133 159 165

Top Flange F07 F07 F07 F07 F07 F07 F10 F10 F10

Weight(kg) 3.8 4.3 4.7 7.0 8.5 11.5 15.6 28.8 35.0

Material List

Dimensions (mm)


Double Flanges Concentric Butterfly Valve (Size 3"-24" 150PSI/250PSI)Fig.2111-DI.Disc,2113-S.S Disc

Butterfly Valve

Specification Valves comply with AWWA C504/EN593 Rubber lined. Actuator-ready with top-flange in accordance with ISO 5211-1.Handle or gearbox operated. Flanges to ANSI B16.1 Class125 or ANSI B16.2 Class250.

Working Pressure 150psi for ANSI B16.1 Class125 flange. 250psi for ANSI B16.2 Class250 flange. MJ-MJ end valve pressure can be both 150psi and 250psi.


Corrosion Protection Internally and externally liquid epoxy painted or fusion bonded epoxypowder coated (FBE). Notes: Design and material are subject to change without notice.

PART Materials ASTM Spec.

Body Cast Iron ASTEM A126 Class B

Seat EPDM/NBR/Viton Commercial

DiscStainless Steel ASTM A351 CF8/CF8M

DI with SS316 edge ASTM A536 65-45-12

Stem Stainless Steel AISI 420

V-Packing EPDM/NBR Commercial

Cover Plate Ductile Iron ASTM A536 65-45-12

Size 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24"

A6-5/16 (160)

7-1/16 (179)

8-3/8 (213)

9-5/8 (245)

10-15/16 (277)

12-1/2 (318)

14-1/16 (357)

16-1/16 (408)

17-1/4 (438)

18-9/16 (472)

22-9/16 (573)

B3-11/16

(93)5-1/2 (140)

6-13/16 (173)

8 (204)

9-5/16 (237)

10-13/16 (278)

12-1/8 (308)

12-3/8 (315)

13 (331)

14-5/16 (363)

16-3/4 (425)

C1-3/16

(30)1-3/16

(30)1-3/16

(30)1-3/16

(30)1-3/16

(30)1-3/16

(30)1-3/4 (45)

1-3/4 (45)

1-3/4 (45)

1-3/4 (45)

1-3/4 (45)

D3-9/16

(90)3-9/16

(90)4-15/16

(125)4-15/16

(125)4-15/16

(125)5-15/16

(150)5-15/16

(150)8-5/16 (210)

8-5/16 (210)

8-5/16 (210)

8-5/16 (210)

E

ANSI 125# FL.

5 (127)

5 (127)

5 (127)

6 (152)

8 (203)

8 (203)

8 (203)

8 (203)

8 (203)

8 (203)

8 (203)

ANSI 250# FL.

5 (127)

5 (127)

5 (127)

6 (152)

8 (203)

8 (203)

8 (203)

8 (203)

8 (203)

8 (203)

8 (203)

MJ-MJ8-1/2 (216)

8-1/2 (216)

8-1/2 (216)

8-5/8 (219)

9-1/4 (235)

9-1/4 (235)

11-1/2 (292)

12 (305)

12-1/4 (311)

12-1/2 (318)

13-1/4 (337)

Top Flange F07 F07 F10 F10 F10 F12 F12 F16 F16 F16 F16

Weight(kg) 42 60 75 82 100 170 205 250 316 456 623

Material List

Dimensions (Inch)


Double Eccentric Flange Butterfly Valve (DN100-DN2400 PN10/PN16)Fig.2124-(Steel+SS) Disc,2125-(DI+SS)Disc

Butterfly Valve

Specification Valves comply with EN593.

EPDM or NBR rubber seat.


Gearbox or nut or handwheel operated.

Flanges to EN1092-2 PN10/16 or other types.

Face to face dimensions conforms to EN558-1 basic series13.


Working Temperature -10℃ to 120℃ for EPDM liner. -10℃ to 82℃ for NBR liner.

Corrosion Protection Internally and externally liquid epoxy painted or fusion bonded epoxy

powder coated (FBE).


PART Materials

Bolts Carbon Steel

Nuts Carbon Steel

Washer Carbon Steel

O-Ring NBR

Bottom Shaft AISI 420 Shaft with Carbon Steel Plate

Bushing ASTM B62 C83600

Disc Carbon Steel with SS edge;DI with SS Edge

Pin AISI 420

PART Materials

Nut AISI 420

Upper Shaft AISI 420

Seat EPDM/NBR

Flange Bushing Carbon Steel

Body ASTM A536 65-45-12

Gland ASTM A536 65-45-12

Mounting Flange ASTM A536 65-45-12

Packing Graphite

Key AISI 1045

Size 100 125 150 200 250 300 350 400 450 500 600

L 127 140 140 152 165 178 190 216 222 229 267

H 370 430 490 643 697 798 815 965 950 1077 1365

Material Specification

Dimensions (mm)

Size 700 800 900 1000 1200 1400 1600 1800 2000 2200 2400

L 292 318 330 410 470 530 600 670 760 800 850

H 1454 1587 1472 1890 2174 2270 2899 2820 3130 3490 3755


U-Type Butterfly Valve (DN350-DN2000 PN16) Fig.2141-DI Disc,2143-SS Disc

Specification

Valves comply with EN593.

EPDM/NBR rubber lined.


Gearbox operated.

Flanges to EN1092-2 PN10/16(Other types available on request).

Face to face dimensions conforms to EN558-1 basic series 20.

Corrosion Protection

Internally and externally liquid epoxy painted or fusion bonded epoxy

powder coated(FBE).


Working Pressure

16 bar

Working Temperature

-10℃ to 120℃ for EPDM liner.

-10℃ to 82℃ for NBR liner.




DiscSS304 BS970 304S15 AISI 304

Ductile Iron EN-JS 1050 ASTM A536 65-45-12

Seat EPDM/NBR Commercial Commercial

O-Ring NBR Commercial Commercial


Size 350 400 450 500 600 700 750 800 900

L 78 102 114 127 154 165 190 190 203

D 288 322 341 381 450 486 525 538 632

E 330 375 397 445 520 585 585 610 690

G 45 65 65 65 65 65 65 85 85


Size 1000 1050 1200 1300 1400 1500 1600 1800 2000

L 216 216 254 279 279 318 318 356 406

D 685 720 820 855 919 1008 1069 1200 1325

E 740 770 855 915 955 1067 1079 1277 1360

G 85 85 85 90 90 100 100 120 140


Butterfly Valve

Dimensions (mm)


Check Valve

DESCRIPTION

Design confirms to: DIN3202 F6,EN558-1

Ser48,EN14341(EN12516)

Threaded type "BSP" acc to ISO228-1 and NFE03-005

Flanged type PN6/10/16 acc.to EN1092-2/BS4504/ISO7005-1

ANSI B16.1 Class125(Other types available on request)

Working temperatures: NBR≤80℃，EPDM≤120℃

DN L D C M b F n-d

50 200 165 102 125 19 3 4-19

65 240 185 122 145 19 3 4-19

80 260 200 138 160 19 3 8-19

100 300 220 158 180 19 3 8-19

125 350 250 188 210 19 3 8-19

150 400 285 212 240 19 3 8-13

200 500 340 268 295 20 3 8-23

250 600 395 320 350 22 3 12-23

300 700 445 370 400 24.5 4 12-23

350 800 505 430 460 26.5 4 16-31

DN L2 G KV (m3/h)

25 140 1" 21

32 140 1" 1/4 29

40 145 1" 1/2 57

50 170 2" 78

65 210 2"1/2 12

80 240 3" 250

Dimensions (mm)

Ball check valves , Flanged endsFig.3111 Flange type, Fig.3112 Thread type.

Material List

NO. Part Material

1 BODY GGG40/50

2 BALL AL/DI + NBR/EPDM

3 COVER GGG40/50


Wafer Double Door Check Valve (DN50-DN600 N16/Class125)Fig.3321- D.I Disc, 3322- S.S304 Disc.

Check Valve

Description

The short face to face dimension and compact design of this valve allow

installation and service in tight spaces.

Spring assisted for better dynamic behaviour.

Soft sealed for perfect tightness even at low differential pressure.

Available with flanges EN1092-2 PN10 or PN16, ANSI B16.1 Class125

(Other types available on request).

WRAS approval.

Corrosion Protection

Internally and externally liquid epoxy painted or

fusion bonded epoxy


Notes: Design and material are subject to change

without notice.

Working Pressure

16 bar

Working Temperature

-10℃ to 120℃ for EPDM seat.

-10℃ to 82℃ for NBR seat.

-10℃ to 150℃ for Viton seat. Material List

PART Materials EN Spec. ASTM Specs.

Body Cast Iron EN-JL1040 A126 Class B

Disc Stainless Steel BS970 304S15 A351 CF8

Seat EPDM/NBR/Viton Commercial Commercial

Hinge-PinStainless Steel BS970 420S37 AISI 420

Stop Pin

Pin Retainer Stainless Steel BS970 304S15 AISI 304

Spring Stainless Steel BS970 304S15 AISI 304

Washer PTFE Commercial Commercial

Gasket EPDM/NBR/Viton Commercial Commercial

SizeA

B CWeight

(kg)Table D/E Flange ANSI 125# Flange EN1092-2 PN16 Flange

50 96 102 106 54 66 1.8

65 109 121 126 54 78 2.4

80 126 134 141 57 90 3.2

100 158 172 161 64 115 4.8

125 190 194 191 70 141 7.3

150 210 220 217 76 170 10

200 267 277 272 95 210 14.2

250 331 337 327 108 273 23.6

300 379 407 382 143 324 37.5

350 445 447 442 184 356 62

400 493 511 494 191 406 74

450 559 546 554 203 457 100

500 616 602 616 213 508 155

600 723 715 733 222 600 215

Dimensions (mm)


Check ValveWafer thin Swing Check Valve (DN50-DN600 PN16/Class125)Fig.3311-Steel Disc, 3312-S.S304/316

Specification Design confirms to EN1074-3,EN12266


Available with flanges EN1092-2 PN10 or PN16, ANSI B16.1

Class125 (Other types available on request).


Working Temperature -10℃ to 150℃

Corrosion Protection Internally and externally Cr plated for carbon steel body and disc.



PART PART Meterial

1 BodySS316

CS., DIN GS-Ck25

2 DiscSS316

CS., DIN GS-Ck25

3 Hook Carbon Steel, Zinc Plated

4 Screw SS316

5 O-Ring Viton

6 Holder SS316

Size 50 65 80 100 125 150 200

L 14 14 14 18 18 20 22

D 109 129 144 164 194 220 275

P 31.8 40 51.3 70 91.5 110 163

C 98.3 108.3 129.8 147.3 171.3 201.8 253.8

B 91.7 102.7 123.2 140.7 161.7 192.2 244.2

Weight(kg) 1.0 1.5 1.9 2.3 3.6 5.0 10.5

Size 250 300 350 400 450 500 600

L 26 28 36 41 50 56 56

D 330 380 440 490 537 592 694

P 192 234 270 315 359 410 490

C 305.8 355.8 402.8 452.8 503.8 551.8 647.8

B 294.2 344.2 387.2 437.2 488.2 536.2 632.2

Weight(kg) 14.0 18.2 27.0 36.0 49.0 63.0 83.5

Dimensions (mm)


Wafer Swing Check Valve (DN50-DN600 PN16/Class125)Fig.3331

Check Valve

Specification The short face to face dimension and compact design of this valve allow

installation and service in tight spaces.

Spring assisted for better dynamic behaviour.





Working Temperature -10℃ to 120℃ for EPDM seat. -10℃ to 82℃ for NBR seat. -10℃ to 150℃ for Viton seat.




Material List



ClapperStainless Steel BS970 304S15 A351 CF8

Hinge Arm

Seat EPDM/NBR/Viton Commercial Commercial

Hinge-Pin Stainless Steel BS970 420S37 AISI 420

Spacer PTFE Commercial Commercial


SizeA

B C DWeight

(kg)Table D/E Flange ANSI 125# Flange EN1092-2 PN16 Flange

50 98 102 106 44.5 33 27 1.6

65 111 121 126 48 47 47 2.2

80 130 134 141 51 52 45 2.9

100 162 172 161 57 76 65 4.7

125 194 194 191 63.5 95 100 6.5

150 216 220 217 70 121 121 7.8

200 273 277 272 73 163.5 176 15

250 337 337 337 79 194 220 20

300 384 407 382 86 241 270 31

350 444 447 446 108 267 310 75

400 495 511 515 108 317 320 91

450 558 546 550 108 355.6 370 100

500 615 602 610 140 387.4 410 154

600 723 715 733 152 482.6 480 250

Dimensions (mm)


Working Temperature -10℃ to 120℃ for EPDM seat. -10℃ to 82℃ for NBR seat. -10℃ to 150℃ for Viton seat.

DNL1 b

D C M H F n-dDIN3202 BS5153 DIN3202 BS5153

50 200 203 19 19 165 102 125 118 3 4-19

65 240 216 19 19 185 122 145 135 3 4-19

80 260 241 19 19 200 138 160 160 3 8-19

100 300 292 19 19 220 158 180 182 3 8-19

125 350 330 19 19 250 188 210 205 3 8-19

150 400 356 22 19 285 212 240 235 3 8-23

200 500 495 22 20 340 268 295 275 3 12-23

250 600 622 26 22 405 320 355 320 3 12-28

300 700 698 26 25 460 378 410 365 4 12-28

350 800 787 27 27 520 438 470 400 4 16-28

400 900 864 28 28 580 490 525 430 4 16-31

Dimensions (mm)

Check ValveSwing Check Valve (DN40-DN300 PN16/25)Fig.3211-DIN3202 ,3212-BS4504

Description

1 Face to Face :DIN3202F6, BS5153

2 Flanged ends: DIN2501, BS4504,

3 Normal pressure: 1.0MPa, 1.6MPa, 2.5Mpa

4 Suitable medium: water

5 Working temperature:NBR ≦ 80℃ ,EPDM ≦ 120℃

Material List

NO. Part Material

1 BODY GGG40/GGG50

2 DISC GGG40/GGG50

3 OBTURATING EPDMNBR

4 SHAFT EPDMNBR

5 PACKING GGG40/GGG50


Swing Check Valve (DN40-DN300 PN16/25) Fig.3251

Check Valve

Specification Face to face dimensions according to DIN3202 F6 series.

Suitable for mounting in horizontal and vertical position

(with vertical flow upwards).


Class 125 (Other types available on request).

Working Pressure 16 bar or 25 bar.



Material List




Cover Cast Iron EN-JL1040 A126 Class B

Gasket Graphite Non-asbestos Non-asbestos

Hanger Pin Stainless Steel DIN 17440 X20Cr13 AISI 420

Hanger Ductile Iron EN-JS1050 A536 65-45-12

Disc Cast Iron EN-JL1040 A126 Class B

Disc TrimBrass CuZn39Pn3 B16 C36000

EPDM/NBR Commercial Commercial

Body Trim Brass CuZn39Pn3 B16 C36000

Side Plug Brass CuZn39Pn3 B16 C36000

Size 40 50 65 80 100 125 150 200 250 300

A 180 200 240 260 300 350 400 500 600 700

B 118 120 125 147 158 188 193 250 300 342

Weight(kg) 10 11.5 13 17 25 40 50 58.3 218 282

Dimensions (mm)


Specification Valves comply with EN12334, BS5153, MSS SP-71 or AWWA C508.

Globe shape to provide full flow with low pressure drop.

Suitable for mounting in horizontal and vertical position(with vertical flow

upwards).

Outside lever and adjustable weight or outside lever and spring.


Class 125 (Other types available on request).

Working Pressure DN50-600 — 16barDN50-300 — 25bar



Notes: In ductile iron construction for PN25 or Class250.

Design and material are subject to change without notice.

Material List



Cover Cast Iron EN-JL1040 A126 Class B

Side Plug Brass CuZn39Pb3 B16 C36000

Hanger Pin Stainless Steel BS970 304S15 AISI 304

Hanger Ductile Iron EN-JS1050 A536 65-45-12

Disc Cast Iron EN-JL1040 A126 Class B

Disc TrimBronze EN1982 CC491K B62 C83600

EPDM/NBR Commercial Commercial

Body Trim Bronze EN1982 CC491K B62 C83600

Gasket Graphite Non-asbestos Non-asbestos

Lever Carbon Steel BS970 050A20 AISI 1020

Weight Cast Iron EN-JL1040 A126 Class B

Spring Carbon Steel Spring Steel Spring Steel

Size 50 65 80 100 125 150 200 250 300 350 400 450 500 600

A 203 216 241 292 330 356 495 622 699 787 914 914 1016 1219

B 125 137 147 166 190 217 265 300 342 402 472 500 514 605

Weight(kg) 16.6 22.5 26.4 42.0 61.2 77.4 130.2 205.5 299.5 525 710 820 1060 1680

Dimensions (mm)

Check ValveSwing Check Valve (DN50-DN600 PN16/25 Class125/Class250)Fig.3232, 3233-with level&counterweight

Working Temperature

-10℃ to 120℃ for Bronze or EPDM disc trim

-10℃ to 82℃ for NBR disc trim


Silent Check Valve (DN50-DN400 PN16/PN25/Class125/Class250) Fig.3412

Check Valve

Specification The design is for liquid service and offers many obvious advantages when compared with conventional swing check valve.Spring automatically closes disc at zero flow before flow reversal occurs.This prevents surge and water hammer. Completely guided disc both top and bottom. Soft sealed for perfect tightness even at low differential pressure.Available with flanges EN1092-2 PN10 or PN16, ANSI B16.1 Class125 (Other types available on request).

Working Pressure 16 bar or 25 bar



Notes: In Ductile Iron construction for PN25 or Class250.


Working Temperature

-10℃ to 120℃ for EPDM seat. -10℃ to 82℃ for NBR seat. -10℃ to 150℃ for Viton seat.

Material List


Body Cast Iron EN-JL 1040 A126 Class B

DiscBronze EN1982 CC491K B62 C83600

Stainless Steel BS970 304S15 A351 CF8

SeatBronze EN1982 CC491K B62 C83600

Stainless Steel BS970 304S15 A351 CF8

"Seat O-ring" EPDM/NBR/Viton Commercial Commercial


Bushing Bronze EN1982 CC491K B62 C83600

Screw Stainless Steel BS970 304S15 AISI 304

Size 50 65 80 100 125 150 200 250 300 350 400

L 133 140 152 185 216 248 318 393 362 400 446

D

EN1092-2 PN16 Flange 165 185 200 220 250 285 340 405 460 520 580

EN1092-2 PN25 Flange 165 185 200 235 270 300 360 425 485 555 620

ANSI 125# Flange 152 178 191 229 254 279 343 406 483 533 597

ANSI 250# Flange 165 191 210 254 279 318 381 445 521 584 648

Weight(kg) 7.5 10.3 13.6 18.3 25.7 34.3 60.6 80 125 185 257

Dimensions (mm)


Material List


Body Cast Iron EN-JL 1040 A126 Class B

Seat Cast Iron Integral EN-JL 1040 A126 Class B

Disc Cast Iron EN-JL 1040 A126 Class B

Disc Trim EPDM/NBR/Viton Commercial Commercial


Bushing Bronze EN1982 CC491K B62 C83600

StemStainless Steel BS970 420S37 AISI 420

Brass CuZn39Pb3 B16 C36000

Bracket Cast Iron EN-JL 1040 A126 Class B

Screw Stainless Steel BS970 304S15 AISI 304

Size 50 65 80 100 125 150 200 250 300

L 100 120 140 170 200 230 288 354 410

A 97 125 150 187 220 260 340 420 490

D

EN1092-2 PN16 Flange 165 185 200 220 250 285 340 405 460

EN1092-2 PN25 Flange 165 185 200 235 270 300 360 425 485

ANSI 125# Flange 152 178 191 229 254 279 343 406 483

ANSI 250# Flange 165 191 210 254 279 318 381 445 521

Weight(kg) 8 10 13 17 30 35 50 90 100

Dimensions (mm)

Check ValveGlobe Silent Check Valve (DN50-DN300 PN16/PN25/Class125/Class250)Fig.3422

Specification Comply with the requirements of EN12334.

The design is for liquid service and offers many obvious advantages

when compared with conventional swing check valve.

Spring automatically closes disc at zero flow before flow reversal occurs.

This prevents surge and water hammer.




Working Pressure 16 bar or 25 bar

Corrosion Protection Internally and externally fusion bonded epoxy powder coated(FBE).

Notes: In Ductile Iron construction for PN25 or Class250.


Working Temperature

-10℃ to 120℃ for Bronze EPDM disc trim.

-10℃ to 82℃ for NBR disc trim.

-10℃ to 150℃ for Viton disc trim.


Foot Valve (DN50-DN300 PN16/Class125) Fig.3522

Check Valve

Specification Design for silent operation, positive seating and full flow area.

Suitable for pressure up to 16 Bar water service.

Coated EPDM or NBR disc sealed ring.

Screens are perforated 304 stainless steel with spot welded seam.

Available with flanges to EN1092-2 PN10 or PN16, ANSI B16.1 Class125






Working Temperature

-10℃ to 120℃ for EPDM coated plug.

-10℃ to 82℃ for NBR coated plug.

Material List


Body Cast Iron EN-JS 1040 ASTM A126 Class B

Disc Cast Iron EN-JS 1040 ASTM A126 Class B

Seat Cast Iron Integral EN-JS 1040 ASTM A126 Class B

Disc Trim EPDM/NBR Commercial Commercial

Bushing Bronze EN1982 CC491K ASTM B62 C83600



Support Cast Iron EN-JS 1040 ASTM A126 Class B

Screen Stainless Steel BS970 304S15 AISI 304

Size 50 65 80 100 125 150 200 250 300

A 100 120 140 170 200 230 288 354 410

B 160 205 240 300 355 410 490 575 655

C 94 120 142 177 206 237 290 330 360

D 165 185 200 220 250 285 340 405 460

Weight(kg) 8 10 13 17 30 35 50 90 100

Dimensions (mm)


Globe Valve Globe Valve DN15-DN200,PN16Fig.3711

DN L D D1 D2 f b Z×Φ

15 130 95 65 45 2 14 4×Φ14

20 150 105 75 55 2 16 4×Φ14

25 160 115 85 65 2 16 4×Φ14

32 180 135 100 78 2 18 4×Φ18

40 200 145 110 85 3 18 4×Φ18

50 230 160 125 100 3 20 4×Φ18

65 290 180 145 120 3 20 4×Φ18

80 310 195 160 135 3 22 8×Φ18

100 350 215 180 155 3 24 8×Φ18

125 400 245 210 185 3 26 8×Φ18

150 480 280 240 210 3 28 8×Φ23

200 600 335 295 265 3 30 12×Φ23

Dimensions (mm)

Material List

No. Part Material

1 Body GG20/GGG40/50

2 Disc GG20/GGG40/50

3 Gasket NBR/EPDM

4 Bonnet GG20/GGG40/50

5 Packing Graphite

6 Gland GG20/GGG40/50

7 Handwheel GG20/GGG40/50/Steel


Balance Valve (DN50-DN300 PN16/Class125)Fig.3723-flange type, 3724-Groove type

Globe Valve

Specification Inside screw, non-rising stem.

EPDM coated disc for size DN50-DN200.

SS304 disc with coated EPDM sealed ring for DN250-DN300.

Back seating feature.

Can be set in conjunction with flow charts.

Two test points located on each valve.

Available with flanges to EN1092-2 PN10 or PN16, ANSI B16.1 Class125

(other types available on request).

Groove to Metric or AWWA C606 standard.

Face to face length in accordance with EN558-1 basic series 1.





Working Temperature

-10℃ to 120℃

Material List



DN50-200 Disc Ductile Iron+EPDM Coated EN-JS 1050 ASTM A536 65-45-12

DN250-300 Disc Stainless Steel with coated EPDM seal ring BS970 304S15 ASTM A351 CF8

Disc Nut Brass CuZn39Pb3 ASTM B16 C36000

Stem Stainless Steel BS970 420S37 ANSI 420

O-Ring EPDM Commercial Commercial

Bonnet Ductile Iron EN-JS 1050 ASTM A536 65-45-12

Gasket EPDM Commercial Commercial

Handwheel Ductile Iron EN-JS 1050 ASTM A536 65-45-12

Size 50 65 80 100 125 150 200 250 300

L 230 290 310 350 400 480 600 730 850

H 260 293 305 323 353 388 453 554 566

D 180 180 180 180 260 260 260 450 450

OD 60 73.0/76.1 88.9 114.3 139.7/141.3 165.1/168.3 219.1 273.0 323.9

Weight(kg) 12 17 24.5 30 49 62.5 100 195 315

Dimensions (mm)


AIR VALVEAutomatic Air Release ValveFig.4211

Specification 1. Flanges acc.EN1092-2

2. Thread connections acc.PN-EN10226-1:2006

3. Leakproofness class - A

4. Working pressure PN16

5.Medium temperature up to 70℃

Material List

No. Part Material

1 Body GGG40/50

2 Ball S.S304

3 Seat EPCM

4 Bonnet GGG40/50

5 Body GGG40/50

6 Ball S.S304

7 Bonnet GGG40/50

DN D B C b H

50 165 102 125 19 255

65 185 122 145 19 276

80 200 138 160 19 303

100 220 158 180 19 312

125 250 188 210 19 335

150 285 212 240 19 400

200 340 268 295 20 468

Dimensions (mm)


Double Orifince Air Release Valve Fig.4221-Double , Fig4231-Triple

AIR VALVE

Double Orifice Air Release Valves

Triple Function Air release valve

DN D D1 D2 B f n-d

40 150 110 84 19 3 4-19

50 165 125 99 19 3 4-19

65 185 145 118 19 3 4-19

80 200 160 132 19 3 8-19

100 220 180 156 19 3 8-19

125 250 210 184 19 3 8-19

150 285 240 211 19 3 8-23

200 340 295 266 20 3 12-23

250 405 355 319 22 3 12-28

300 460 410 370 24.5 4 12-28

Dimensions (mm)


AIR VALVECOMBINATION AIR VALVE FOR SEWAGEFig4300

Specification Single Chamber double orifice triple function air and vacuum

automatic release valve

Designed to operate with liquids carrying solid particles such as

sewage and effluent.

Release air during charging of the system and intake air during

draining of the system.

complete separation of the liquid from the sealing mechanism

provide optimum work conditions.

All inner metal parts made of stainless steel.

Flange to En1092-2 PN16(other types available on request)

Working Pressure Working pressure range:0.5-16bar Shell test pressure (for body):24bar Seat test pressure：17.6bar

Working Temperature

-10℃ to 60℃

Material List

No. Part Material

1 Body DI,EN1563 EN-JS1050

2 Float SS316

3 Nut SS316

4 Spindle SS316

5 Spring SS316

6 Stopper Polypropylene

7 Crown Nut SS316

8 Washer SS316

9 Gasket NBR

10 Bonnet DI,EN1563 EN-JS1050

11 O-Ring NBR

12 Cover Reinforced Nylon

13 Disc NBR+SS316+Nylon

14 Bolt SS316

15 Plate SS316

16 Bolt SS316

17 Washer SS316

18 Plastic Base Reinforced Nylon

19 Guide Block Polypropylene

20 Ball Valve DN25 SS316

Size DN80 DN100 DN150 DN200

A 601 601 601 601

B 275 275 275 275

Dimensions (mm)


Hydraulic Control valve Fig.5300

AIR VALVE

100X Floating valve

400X Flowing control Valve

600X Electric Control Valve

800X Pressure differential bypass balancing valve

200X Pressure Reducing Valve

500X Pressure relief/holding Pilot Valve

700X Pump control Valve

300X CHECK VALVES


200X Pressure Reducing Valve

500X Pressure relief/holding Pilot Valve

Ball ValveTwo-pieces Ball Valve (DN15-DN200 PN16/Class125)Fig,5611

Specification Valves comply with DIN/NF/MSS SP-72.

Low operating torque.

Actuator-ready with top-flange in accordance to ISO 5211-1.

Flanges EN1092-2 PN16(Other types are available on request).


Corrosion Protection Internally and externally liquid epoxy painted.


Working Temperature

-10℃ to 120℃

Material List



End Cap Ductile Iron EN-JS 1050 ASTM A536 65-45-12

Ball Stainless Steel BS970 304S15 AISI 304


Body Seat Teflon+Graphite Commercial Commercial

Packing Teflon+Graphite Commercial Commercial

O-Ring EPDM/Viton Commercial Commercial

Stopper Stainless Steel BS970 304S15 AISI 304

Handle Carbon Steel Mild Steel Mild Steel

Size 15 20 25 32 40 50 65 80 100 125 150 200

L

DIN 115 120 125 130 140 150 170 180 190 200 210 400

NF — — — — — 142 154 160 172 186 200 —

MSS 108 117 127 140 165 178 191 203 229 254 268 292

H 70 75 85 105 110 115 130 140 155 195 240 325

Weight(kg) 2 3.2 4.1 5 6.5 9 14 18 26.4 34 42 50

Dimensions (mm)


Y-Strainer DN50-DN300 Fig.5111

Strainer

Description 1.DIN3302-F1/EN558-1 GR48

2.Pressure:PN10 / PN16/PN25

3.Working temperature: -10 -70℃ for Epoxy paint

-10-120℃ for Polivinyl paint

4.Stainless Steel Filter Screen

5.Flange connecting, EN1092-2 PN10/ PN16/PN25.

Material List

No Part Material

1 Body GG25/GGG40/50

2 Bonnet GG25/GGG40/50

3 Screen Stainless steel

4 Gasket NBR/Asbestos/EPDM

5 Screw Galvanized steel/S.S

6 Emptying Screw S.S / forged steel

DN (mm) PN (Pa) L (mm) H H1 D d K lxn

50 1.0-1.6 230 140 270 165 102 125 18*4

65 1.0-1.6 290 165 310 185 122 145 18*4

80 1.0-1.6 310 200 370 200 138 160 18*4/(8)

100 1.0-1.6 350 230 440 220 158 180 18*8

125 1.0-1.6 400 280 540 250 188 210 18*8

150 1.0-1.6 480 330 560 285 212 240 22*8

200 1.0-1.6 600 358 600 340 268 295 22*8(12)

250 1.0-1.6 730 509 700 395 320 350/355 22(26)*12

300 1.0-1.6 850 531 750 445 370 400/410 22(26)*12

Dimensions (mm)


StrainerY-Strainer (DN50-DN600 PN16/Class125, PN25/Class250)Fig.5112-BS,5114-ANSI

Specification NPT or BSPT blowoff outlet on cover. Blowoff outlets are finished with plugs.


Recessed seat in body assures accurate screen alignment.

Available with flanges to EN1092-2 PN16/PN25, ANSI B16.1 Class125

or ANSI B16.2 Class250(Other types available on request).

WRAS approved.





Working Temperature

-10℃ to 120℃


Standard Screens


BodyCast Iron EN-JL 1040 ASTEM A126 Class B


CoverCast Iron EN-JL 1040 ASTEM A126 Class B


Screen Sainless Steel BS970 304S15 AISI 304

Gasket Teflon/Graphite Commercial Commercial

PlugCast Iron EN-JL 1040 ASTEM A126 Class B


Size Hole Dia. Free Flow Area

DN50-80 1.5mm 33%

DN100-600 3.0mm 40%

Size 50 65 80 100 125 150 200 250 300 350 400 450 500 600

L 230 273 295 352 416 470 543 660 770 960 1079 1168 1275 1450

H 150 185 205 245 294 330 415 492 562 755 827 930 980 1170

Plug 1/2" 1" 1" 1" 1-1/4" 1-1/2" 1-1/2" 2" 2" 2" 2" 2" 2" 2"

Weight(kg) 10 26 23.5 34 52 70 110 185 295 458 556 627 780 1080

Dimensions (mm)


GROOVED Y-Strainer (DN50-DN300 PN16/Class125, PN25/Class250)Fig.5124

Strainer

Specification NPT or BSPT blowoff outlet on cover. Blowoff outlets are finished with plugs.


Recessed seat in body assures accurate screen alignment.

Groove dimensions comply with Metric or AWWA C606.





Working Temperature

-10℃ to 120℃


Standard Screens



Cover Ductile Iron EN-JS 1050 ASTM A536 65-45-12



Plug Ductile Iron EN-JS 1050 ASTM A536 65-45-12


DN50-80 1.5mm 33%

DN100-300 3.0mm 40%

Size 50 65 80 100 125 150 200 250 300

OD 60.3 73.0/76.1 88.9 114.3 139.7/141.3 165.1/168.3 219.1 273.0 323.9

L 225 285 318 375 448 502 640 710 779

H 150 185 205 245 294 330 415 492 562

Plug 1/2" 1" 1" 1" 1-1/4" 1-1/2" 1-1/2" 2" 2"

Weight(kg) 7 11 13.4 21 36 54 100 141 233

Dimensions (mm)


StrainerBasket Strainer (DN50-DN600 PN16/Class125, PN25/Class250)Fig.5213

Specification NPT or BSPT blowoff outlet on body. Blowoff outlets are finished with plugs.


Available with flanges to EN1092-2 PN16/PN25, ANSI B16.1 Class125 or

ANSI B16.2 Class250(Other types available on request).





Working Temperature

-10℃ to 120℃


Standard Screens


BodyCast Iron EN-JL 1040 ASTEM A126 Class B


CoverCast Iron EN-JL 1040 ASTEM A126 Class B




PlugCast Iron EN-JL 1040 ASTEM A126 Class B



DN50-80 1.5mm 33%

DN100-600 3.0mm 40%

Size 50 65 80 100 125 150 200 250 300 350 400 450 500 600

L 207 210 251 292 334 378 475 511 680 769 842 842 842 1054

A 225 250 297 330 370 410 530 615 770 925 972 1010 1110 1690

B 128 155 190 202 218 243 305 335 425 585 590 543 600 1175

Plug 1/2" 3/4" 3/4" 1" 1" 1" 1-1/2" 1-1/2" 2" 2" 2" 2" 2" 2"

Weight(kg) 11 19 21 30 43 58 100 151 270 470 500 645 850 1250

Dimensions (mm)


Fire Hydrant( BS750 Type II PN16 ) Fig.8400

Hydrant

Specification Comply with BS750 Type II. Seating type is resilient material to Ductile Iron integral seat. Flange drilled to DN80 EN1092-2 PN16 and BS10 Table E. 2-1/2" London Round Thread outlet. Other type outlets are available,such as 2-1/2" nstantaneous outlet, 2-1/2" Belfast V outlet and Dublin Bayonet outlet. Bottom drain connection. Fusion bonded epoxy coated interior and exterior. WRAS approved.


Corrosion Protection IInternally and externally fusion bonded epoxy powder coated(FBE).


Working Temperature

-10℃ to 120℃


No. PART Materials

1 Body Ductile Iron ASTM A536 65-45-12

2 Bolt Stainless Steel AISI 304

3 Holder Stainless Steel AISI 304

4 Gasket NBR

5 Disc Ductile Iron ASTM A536 65-45-12

6 Stem Nut Brass ASTM B16 C36000

7 Screw Steel

8 Stem Stainless Steel AISI 420

9 O-Ring NBR

10 Cover Ductile Iron ASTM A536 65-45-12

11 Washer Copper

12 O-Ring NBR

13 Cap Gasket Plastic

14 Driver Cap Cast Iron ASTM A126 Class B


16 Indicator Cap Plastic


18 Washer Stainless Steel AISI 201

19 Dust Cap Plastic

20 Outlet Brass ASTM B16 C36000

21 O-Ring NBR

22 Rope Stainless Steel

23 Plug Plastic


HydrantBS750 Pillar Hydrant Fig.8300

DESCRIPTION DIMENSION ACCORDING TO BS750-DN100

FLANGE DRILLING TO EN1092-2,PN16

MATERIAL LIST


Part Materials

Body Ductile Iron GGG40 / 50

Outlet Brass

Cap Ductile Iron GGG40 / 50

Chain Galvanized Steel

Underground Hydrant fig.8100

DN RD H H1

[mm]

80

750 665 500

1000 915 750

1250 1165 1000

1500 1415 1250

1800 1715 1500

100

1000 935 750

1250 1185 1000

1500 1435 1250

1800 1735 1500

Dimensions (mm)


"Fire Hydrant"( Dry-Barriel AWWA 250PSI )Fig.8310

Hydrant

Specification Comply with AWWA C502.

Seating type is resilient material to bronze seat construction.

One Pumper nozzle, 4.5-4NH thread.

Two hose nozzle, 2.5-7.5NH thread. Other threads are available.

Multiple buried lengths available.

6" mechanical joint designed to ANSI/AWWA C153/A21.53.

Working Pressure 250psi

Corrosion Protection IInternally and externally liquid epoxy painted.


without notice.

Working Temperature

0.6℃ to 52℃


No. PART Materials ASTM Spec.

1 Operating Nut Bronze ASTM B62

2 Hold Down Nut Bronze ASTM B62

3 O-Ring NBR Commercial

4 Bonnet Cast Iron ASTM A126 Class B

5 Bonnet Bolt&Nut Stainless Steel AISI 201

6 Upper Rod Carbon Steel AISI 1045

7 Pumper Nozzle Bronze ASTM B62

8 Pumper Nozzle Gasket NBR Commercial

9 Hose Nozzle Bronze ASTM B62

10 Hose Nozzle Gasket NBR Commercial

11 Pumper Nozzle Cap Cast Iron ASTM A126 Class B

12 Hose Nozzle Cap Cast Iron ASTM A126 Class B

13 Cap Chain Carbon Steel Plated

14 Standpipe Upper Cast Iron ASTM A126 Class B

15 Safety coupling Stainless Steel ASTM A890

16 Safety Flange Bolt&Nut Stainless Steel AISI 201

17 Safety Flange Cast Iron ASTM A126 Class B

18 Lower Rod Carbon Steel AISI 1045

19 Standpipe Lower Cast Iron ASTM A126 Class B

20 Stem Pin Stainless Steel ASTM A276

21 Drain Ring Housing Ductile Iron ASTM A536 65-45-12

22 Drain Ring Bronze ASTM B62

23 Seat Ring Bronze ASTM B62

24 Bottom Plate Ductile Iron ASTM A536 65-45-12

25 Disc Ring NBR Commercial

26 Bottom Plate Nut Ductile Iron ASTM A536 65-45-12

27 Elbow Ductile Iron ASTM A536 65-45-12

L 3'-0" 3'-6" 4'-0" 4'-6" 5'-0" 5'-6" 6'-0"

Weight(kg) 170 178 183 196 200 210 215

Dimensions (Inch)


Corrosion Protection IInternally and externally liquid epoxy painted.


without notice.

Hydrant"Fire Hydrant" ( Wet-Barrel 250PSI)Fig.8320

Specification Comply with AWWA C503.

4.5" pumper nozzles; 6mm hose nozzles.

Nozzle threads according to NFPA 1963 standard.

Flanges to ANSI B16.1 Class125(6"),

Other types available upon request.

Working Pressure 250PSI125PSI

Corrosion Protection Internally and externally epoxy power coated to a dry film to minimum

0.6mm thickness and then fusion bonded epoxy powder coated(FBE).

Notes: Design and material are subject to change without notice. Working Temperature

-10℃ to 80℃


No. PART Materials ASTM Spec.

1 Body Ductile Iron ASTM A536-65-45-12

2 Pumper Nozzle Cap Cast Iron ASTM A126 Class B

3 Pumper Nozzle Bronze ASTM B62 C83600

4 Main Valve Rubber NBR

5 Main Valve Holder Stainless Steel AISI 304

6 Hose Nozzle Cap Cast Iron ASTM A126 Class B

7 Hose Nozzle Bronze ASTM B62 C83600

8 Stem Stainless Steel AISI 304

9 Stem Nut Bronze ASTM B62 C83600

10 Operating Nut Bronze ASTM B62 C83600

11 O-Ring Rubber NBR

12 Pumper Nozzle Gasket Rubber NBR

13 Hose Nozzle Gasket Rubber NBR


OVERGROUND HYDRANTFig.8210

Hydrant


No Part Material

1 Upper BodyDuctile Iron GGG40

2 Bottom Body

3 ColumnDuct i le I ron GGG40; Steel

4 BonnetDuctile Iron GGG40, EN-GJL-250

5 Valve HeadDuct i le I ron GGG40/EPDM

6 CapDuctile Iron GGG40, EN-GJL-250

7 Valve Stem Stainless Steel X20Cr13

8 Spindle Steel ;X20Cr13

9 Attachment A Aluminium Alsi

10 Attachment B Aluminium Alsi

11 Gasket A EPDM

12 Gasket B EPDM

13 Gland Seal Brass

14 Stem Nut Brass

15 Gasket O-Ring EPDM

16 BoltGalvanized Steel; Stainless steel A2

17 NutGalvanized Steel ; Stainless steel A2

18 Dehydrator Brass

Dimensions (mm)

DN RD L H H1 H2

[mm]

80

1250 1890 2065 1130

5651500 2140 2315 1380

1800 2440 2615 1680

100

1250 1900 2080 1130

5651500 2150 2330 1380

1800 2450 2630 1680


HydrantOverground Hydrant Breakage typeFig.8220


No Part Material

1 Upper BodyDuctile Iron GGG40

2 Bottom Body

3 ColumnDuct i le I ron GGG40; Steel

4 BonnetDuctile Iron GGG40, EN-GJL-250

5 Valve HeadDuct i le I ron GGG40/EPDM

6 CapDuctile Iron GGG40, EN-GJL-250

7 Valve Stem Stainless Steel X20Cr13

8 Spindle Steel R45

9 Attachment A Aluminium Alsi

10 Attachment B Aluminium Alsi

11 Gasket A EPDM

12 Gasket B EPDM

13 Gland Seal Brass

14 Stem Nut Brass

15 Gasket O-Ring EPDM

16 BoltSteel Fe/Zn5; Stainless steel A2

17 NutSteel Fe/Zn5; Stainless steel A2

18 Dehydrator Brass

19 Seat Brass

Dimensions (mm)

DN RD L H H1 H2 H3

[mm]

80

1250 1890 2060 1130

640 1101500 2140 2310 1380

1800 2440 2610 1680

100

1250 1950 2150 1110

640 1101500 2200 2400 1360

1800 2500 2700 1660


FLANGED PIPE FITTINGS Pipe Fittings

BLIND FLANGE Fig.6710 & 6720 -thread

DN DK

PN16(10)I

PN16(10)C f

n PN16(10) G

Weight

[mm] [kg]

50 165 125 18 19 3 4 3/8'; 1/2"; 3/4"; 1"; 1 1/4"; 1 1/2"; 2"; 3.0

80 200 160 18 19 3 8(4) 1/2"; 3/4"; 1"; 1 1/4"; 1 1/2"; 2"; 2 1/2", 3" 4.0

100 220 180 18 19 3 81/2"; 3/4"; 1"; 1 1/4"; 1 1/2"; 2"; 2 1/2", 3"; 3 1/2", 4"

4.5

150 285 240 22 19 3 81/2"; 3/4"; 1"; 1 1/4"; 1 1/2"; 2"; 2 1/2", 3"; 3 1/2", 4";

8.0

200 340 295 22 20 3 12(8)3/4"; 1"; 1 1/4"; 1 1/2"; 2"; 2 1/2", 3"; 3 1/2", 4"

11.0

250 405 355(350) 26(22) 22 3 12 3/4"; 1"; 1 1/2"; 2"; 2 1/2", 3"; 3 1/2", 4" 17.0

300 460 410(400) 26(22) 24.5 4 12 1"; 1 1/2"; 2"; 2 1/2", 3"; 3 1/2", 4" 26.0

400 580 525(515) 30(28) 28 4 16 1"; 1 1/2"; 2"; 2 1/2", 3"; 3 1/2", 4" 41.0

500 715 650(620) 34(28) 31.5 5 20 1"; 1 1/2"; 2"; 2 1/2", 3"; 3 1/2", 4"; 65.0

600 840 770(725) 36(31) 36 5 20 1"; 1 1/2"; 2"; 2 1/2", 3"; 3 1/2", 4"; 100.0

800 910 950 43(35) 43 5 24 207.0

1000 1255 1170(1160) 50(40) 50 5 28 360.0

1050* 1230 1160 48 74 28 450.0

1400* 1685 1590 54 84 36 1,110.0

Dimensions (mm)


Pipe Fittings

Dimensions

Dimensions

(mm)

(mm)

Cast Iron Stub Pipe - F (6510)

Cast Iron Stub Pipe - FW (6520)

DN L DN L

[mm]

50 340 250 500

65 345 300 440

80 350 350 460

100 360 400 480

125 370 500 520

150 380 600 560

200 400 800 600

250 420 1000 600

Dn DZ

[mm]

80 90

100 110

150 160

200 225

250 280

300 315

400 450

500 560

600 630

DESCRIPTION Comply with AWWA C503.

4.5" pumper nozzles; 6mm hose nozzles.

Nozzle threads according to NFPA 1963 standard.

Flanges to ANSI B16.1 Class125(6"),

Other types available upon request.

Materials Body - Ductile Iron EN-GJS 500-7

Standard execution:epoxide paint RAL5005 250μm

Application In installations: for water, potable water and other inert fluids.

Type 6510 - Cast Iron Pipe

Type 6520 - PVC Pipe


Short Double Flanged Pipe FF (6530)Pipe Fittings

DN L WEIGHT DN L WEIGHT

[mm] [kg] [mm] [kg]

50

200 8.2

150

600 28.0

300 8.6 700 32.0

400 8.8 800 34.0

500 9.0 1000 36.0

80

100 7.5

200

100 20.0

200 9.0 200 23.0

300 10.0 300 27.0

400 12.5 400 30.0

500 13.0 500 33.0

600 15.0 1000 50.0

700 16.0

250

200 32.0

800 18.0 300 36.0

1000 22.0 500 46.0

100

100 9.0 1000 69.0

200 12.0

300

200 42.0

300 13.0 300 48.0

400 14.0 500 63.0

500 16.0 1000 89.0

600 18.0 400

500 87.0

700 20.0 1000 155.0

800 22.0 500

500 140.0

1000 28.0 1000 198.0

150

100 15.0 600

500 180.0

200 17.0 1000 250.0

300 19.0 800

500 265.0

400 20.0 1000 412.0

500 24.0 800* 6000 1450.0

1050* 6000 1950.0

1400* 6000 2880.0

Design features Flanges acc. to PN-EN 1092-2

Working pressure PN10, PN16

Version acc. to PN-EN 545:2010

Design features Body - Ductile Iron EN-GJS500-7; Carbon Steel Q235B



Dimensions (mm)

* For carbon steel.


Pipe FittingsDouble Flange Concentric Taper - FFR (6400)

DN dn L WEIGHT DN dn L WEIGHT

[mm] [kg] [mm] [kg]

50 40 150 5.9

250

80 300 27.5

65 50 200 6.9 100 300 28.4

80

40 200 8.0 150 300 33.0

50 120/200 8.4 200 300 29.5

65 200 8.8

300

100 300 31.3

100

50 200 9.4 150 300 36.7

65 200 9.8 150 600 46.0

80 200 10.2 200 300 51.0

125 80 200 14.0 250 300 50.0

150

50 200 14.2 350 300 300 54.2

80 200 14.6

400

200 300 61.0

80 300 16.5 250 300 66.0

100 200 14.8 300 300 73.0

100 300 16.8 350 300 85.0

200

50 300 22.2 500

300 600 143.0

80 300 22.5 400 600 162.0

100 300 27.0 600

400 600 218.0

100 300 22.9 500 600 238.0

150 300 23.7 800 600 600 312.0

Dimensions (mm)

* For carbon steel.

DESCRIPTION Flanges acc. to PN-EN 1092-2:1999



Materials Body - Ductle Iron GJS 500-7; Carbon Steel Q235B




Tee Pipe -T (6100)Pipe Fittings

Design features Flanges acc. to PN-EN 1092-2:1999



Design features Body - Ductile Iron GJS 500-7; Carbon Steel Q235B


Application In installations: for water, potable water and other inert

fluids.

Dimensions (mm)

DN dn L WEIGHT DN dn L WEIGHT

[mm] [kg] [mm] [kg]

50 50 300 11.5

250

80 405 50.0

6550 330 12.1 80 700 65.0

65 320 12.5 100 425 51.0

80

50 310 14.2 100 700 69.0

65 325 14.6 150 700 70.0

80 330 15.6 200 540 63.7

100

40 320 17.8 200 700 80.0

50 320 18.5 250 600 72.7

65 360 20.0 250 700 89.0

80 330 18.4

300

80 425 62.2

80 360 19.0 80 800 93.0

100 360 19.3 100 450 65.1

125

60 330 22.8 100 800 97.0

80 400 23.1 150 505 72.4

100 400 23.5 150 800 98.0

125 400 25.5 200 800 101.0

150

50 340 29.5 250 620 90.0

60 340 27.8 250 800 106.0

80 440 28.5 300 680 100.9

100 440 29.5 300 800 125.0

150 440 32.5

350

150 530 123.0

200

50 520 43.2 200 850 129.0

80 380 41.5 250 645 135.0

80 520 43.5 300 850 141.0

100 400 44.0 350 850 167.0

100 520 44.5

125 520 45.0

150 520 45.5

200 520 49.0


Flanged duckfoot bend-N & cross-TT Pipe Fittings

Dimensions

Dimensions

(mm)

(mm)

(mm)

Cast Iron Duckfoot Elbow - N (6600)

Flanged Cross - TT (6200)

Design features Flanges acc. to PN-EN 1092-2:1999



Design features Body - Ductile Iron EN-GJS 500-7



DN l WEIGHT

[mm] [kg]

80 165 13.0

100 180 17.0

150 220 29.0

200 260 46.0

250 350 73.0

300 400 104.0

400 500 177.0

500 600 281.0

600 700 425.0

800 900 860.0

DN L L1 WEIGHT

[mm] [kg]

50 300 150 24

80 330 165 25.0

100 360 180 27.0

150 440 220 50.0

200 520 260 80.0

250 600 300 104.0

300 680 340 145.0

400 900 450 215.0

500 900 450 305.0

600 1100 550 420.0


Pipe Fittings

Design features Flanges acc. to PN-EN 1092-2



Design features Body - Ductile Iron EN-GJS500-7; Carbon Steel Q235B.



Double Flanged Bend - Q (6310)

Double Flanged Bend - FFK (6320)

Dimensions (mm)

DN L WEIGHT

[mm] [kg]

50 150 7.0

80 165 10.0

100 180 13.0

150 220 20.0

200 260 32.0

250 350 50.0

300 400 70.0

350 450 105.0

400 500 114.0

500 600 180.0

600 700 270.0

800 900 527.0

800* 900 750.0

DN L WEIGHT L WEIGHT L WEIGHT L WEIGHT

[mm] [mm] [kg] [mm] [kg] [mm] [kg] [mm] [kg]

Angel Degree 11.25° 22.5° 30° 45°

80 130 9.0 130 9.0 130 9.0 130 9.5

100 140 11.5 140 11.5 140 11.5 140 11.0

150 160 18.5 160 18.5 160 19.0 160 19.0

200 180 31.5 180 32.0 180 28.0 180 28.0

250 210 55.0 210 55.0 210 50.0 350 62.0

300 255 77.0 255 77.0 255 60.0 400 81.0

* For carbon steel.

Dimensions (mm)

Flanged Elbow-Q


Design features Body - Ductile Iron EN-GJS500-7; Carbon Steel Q235B.


Pipe FittingsDismantling Joint - F3 （7600）

Technical Data:

Working pressure PN10

Medium temperature up to +70°C

Design features:

The connecting elements are made from galvanized steel(posibility

stainless steel).

All steel parts are protected against corrosion.

Standard Execution:

Steel S235JR,Ductile Iron EN-GJS-400-15, connecting elements -

galvanized steel, EPDM,

epoxide paint RAL5005 250μm.

Material List

No. Parts Materials

1 FlangeSteel Q235, Ductile Iron EN-GJS-400-15;

2 Flange

3 Flange

4 Gasket Rubber EPDM /NBR

5 Screw

Galvanized Steel; Dacromet Steel. 6 Nut

7 Washer

DN L A+ / A- D K M n Weight

[mm] [szt] [kg]

32 180 25 140 100 16 4 7.5

40 180 25 150 110 16 4 9.5

50 180 25 165 125 16 4 11.0

65 180 25 185 145 16 4 13.0

80 200 25 200 160 16 8 17.0

100 200 25 220 180 16 8 21.0

125 200 25 250 210 16 8 26.0

150 200 25 285 240 20 8 35.0

175 220 25 315 270 20 8 44.0

200 220 25 340 295 20 8 49.0

250 220 25 395 350 20 12 65.0

300 220 25 445 400 20 12 73.0

350 230 25 505 460 20 16 97.0

400 230 25 565 515 24 16 125.0

450 250 25 615 565 24 20 140.0

500 260 25 670 620 24 20 162.0

550 260 25 730 675 27 20 195.0

DN L A+ / A- D K M n Weight

[mm] [szt] [kg]

600 260 25 780 725 27 20 205.0

650 260 25 835 780 27 24 237.0

700 260 25 895 840 27 24 260.0

800 290 25 1015 950 30 24 355.0

900 290 25 1115 1050 30 28 408.0

1000 290 25 1230 1160 33 28 450.0

1100 300 25 1340 1270 33 32 585.0

1200 320 25 1455 1380 36 32 750.0

1300 340 25 1575 1490 39 32 912.0

1400 360 25 1675 1590 39 36 1,035.0

1500 380 25 1785 1700 39 36 1,162.0

1600 390 25 1915 1820 45 40 1,520.0

1800 400 25 2115 2020 45 44 1,830.0

2000 410 25 2325 2230 45 48 2,280.0

2200 430 25 2550 2440 52 52 2,790.0

2400 440 25 2760 2650 52 56 3,510.0

Application:

Dismantling joint(compensation connectors) F3 are used

for installation and removal of the fitting on the water

network.

Dimensions (mm)


GIBAULT JOINT -7300 COUPLING

Gibault joint is a coupling designd to supply a efficiency and

economical method for PVC pipeAnd it is a ideal way for re-

connecting pipe after removal of the damaged PVC pipe or

for Connecting the two pipe into pipeline

The body is made by ductile iron material

The gasket is EPDM material for drinkable water or NBR material

for oil/industrial pipe line

The surface with fusion bond epoxy or polyesrter coating which is

suitable for drinkable water

The fastener is carbon steel galvanized.

Material List

No Reference Material standard

1 Sleeve Ductile iron EN1563

2 End ring Ductile iron EN1563

3 Fastener Carbon steel with galvanize EN20289

4 O-ring EPDM/NBR EN681/EN682

NO SIZE BOLT A H WEIGHT

L QTY [mm] [mm] [kg]

1 63 180 2 147 130 1.80

2 75 180 2 147 130 2.50

3 90 180 3 165 130 2.70

4 110 210 3 185 150 3.60

5 125 210 4 200 150 4.00

6 140 210 4 215 150 5.00

7 160 240 4 236 150 6.90

8 180 240 6 255 190 8.10

9 200 260 6 276 190 8.60

10 225 290 6 285 190 11.00

11 250 290 6 340 200 18.00

12 280 290 6 345 200 20.50

13 315 290 6 352 200 22.00

Dimensions (mm)


COUPLINGUniversal Coupling（7200）

Technical Data:

Conform to AWWA ANSI C219 & Europe Standard

Nominal pressure PN16

Working Temperature 70°C

Design features:

The EPDM gasket enable easy slide pipe into connector and make provision for

good contact to a pipe

even in places with light defects, unevenness, corrosion pits and the deviation

of coaxial angel of 6°.

The bolts are galvanizing or stainless steel.

All parts are protected against corrosion.

Coating - Epoxy RAL5005 250μm

Application:

Connection lines on straight end of pipes: cast iron, iron, asbestos-cement

and PVC.

Assembly:

Assembly in optional position.

Cut the pipe perpendicular to centre line.

Unscrew a bolt from flange.

Wet the end of pipe and slide over the body.

Turn up the screw at cross to get coaxial position.

※other executions on request

Dn Dz L M Type of Pipes

[mm]

50 59-72 165 155 Upvc,DI, CI,AC,Steel








250A 244-276 174 357 Upvc,DI, CI,AC,Steel

250B 272-289 176 352 Upvc,DI, CI,AC,Steel





No. Parts Materials

1 Sleeve Ductile Iron EN-GJS-500-72 Gland

3 Gasket Rubber EPDM / NBR

4 Screw

Galvanized Steel5 Nut

6 WasherDimensions (mm)

Material List


Universal Flange Adaptor （7210）COUPLING

Technical Data:

Confirm to AWWA ANSI C219 & Europe Standard

Flanges acc. to PN-EN 1092-2:1999



Design features:

The connector is made from nodular cast iron.

The EPDM gasket enable easy slide pipe into connector and make provision for

good contact to a pipe

even in places with light defects, unevenness, corrosion pits and the deviation

of coaxial angel of 3°.




Hygienic attest by PZH

Application:

Connection lines on straight end of pipes: cast iron, iron, asbestos-cement,

PVC to flanged fittings.

Assembly:






※other executions on request

Dn Dz L M Type of Pipes

[mm]









250A 244-276 174 357 Upvc,DI, CI,AC,Steel

250B 272-289 176 352 Upvc,DI, CI,AC,Steel





Dimensions (mm)

No. Parts Materials

1 SleeveDuctile Iron EN-GJS-500-7

2 Gland

3 Gasket Rubber EPDM /NBR

4 Screw Galvanized Steel ;Dacromet Steel

5 Nut Galvanized Steel ;Dacromet Steel

6 Washer Galvanized Steel ;Dacromet Steel

Material List


COUPLINGPipe Connector for PVC or PE Pipe（7530）

Technical Data:Flanges acc. to PN-EN 1092-2:1999



Design features:The FORSHEDA's ring make assembly easy and quickly.

The messing clamp ring hold and protect against moving a pipe.



Application:

Connection flanged fittings to PVC and PE pipe lines.

Assembly:


Cut the pipe perpendicular to centre line and make a diagonal bevel 30°.


Wet the end of pipe and slide over the body to

sensible home.

Turn up the screw at cross to get intimate contact the

flange to body.

Attention:

In the case thin-walled pipe(to 3mm) or negative pressure

strengthening sleeve inside pipe must be used.

Dimensions

(mm)

No. Part Materials

1 BodyDuctile Iron EN-GJS-500-7

2 Flange

3 Ring Brass

4 Sealing Ring FORSHEDA 575 Rubber EPDM / NBR

5 Screw Galvanized Steel, Dacromet Steel

6 Washer Galvanized Steel, Daceromet Steel

7 Pipe Galvanized Steel, Daceromet Steel

Material List

Dn DzD

PN16(PN10)K

PN16(PN10)d

l×n PN16(PN10)

f C L Weight

[mm] [kg]

50 63 165 125 102 19×4 3 19 90 3.8

80 90 200 160 138 19×8(4) 3 19 95 5.5

100 110 220 180 156 19×8 3 19 95 6.5

100 125 220 180 156 19×8 3 19 102 7.2

125 125 250 210 188 19×8 3 19 100 8.3

150 160 285 240 215 23×8 3 19 115 11.6

200 200 340 295 268 23×12(8) 3 20 139 14.5

200 225 340 295 268 23×12(8) 3 20 141 15.8

250 250 400 355(350) 320 28(23)×12 3 22 156 22.0

250 280 400 355(350) 320 28(23)×12 3 22 161 23.0

300 315 455 410(400) 378 28(23)×12 4 25 180 33.0

300 355 455 410(400) 378 28(23)×12 4 25 285 55.0

400 400 580 525(515) 480 31(28)×16 4 25 245 53.0

400 450 580 525(515) 480 31(28)×16 4 25 315 71.0

500 500 715(670) 650(620) 582 34(28)×20 4 26 340 90.0

500 560 715(670) 650(620) 582 34(28)×20 4 26 410 105.0

600 630 840(760) 770(725) 720 37(31)×20 5 30 478 145.0


Pipe connector RR Multidiameter（7410）COUPLING

Technical Data:



Design features:

The connector is made from ductile iron.

The EPDM gasket enable easy slide pipe into connector and make provision for good

contact to a pipe even in places with light defects, unevenness, corrosion pits.




Hygienic attest by PZH

Application:

Connection lines on straight end of pipes: cast iron, iron, asbestos-cement,


Assembly:






Dimensions

(mm)

DN Dz L Weight DN Dz L Weight

[mm] kg [mm] [kg]

50 40-75 280 8.5 300 310-350/350-390

370

33/66

60/65 60-95

300

8 350 395-435 39

80 80-115 10.5 400 435-470/470-505 43/45

100 105-135 12500

505-540/540-575 50/70

125 130-165

340

16 575-610 74

150 155-195 18600

610-645/645-680 58/81

175 190-230 21 680-715 82

200 215-258 23 700 710-745 86

225 240-280 360 27 800 810-845 95

250 235-275/270-310 360 16/29

No. Parts Materials

1 BodyDuctile IronEN-GJS-500-7

2 Flange


4 Screw Galvanized Steel; S.S304/316

5 Nut Galvanized Steel; S.S304/316

6 Washer Galvanized Steel; S.S304/316

Material List


COUPLINGPipe connector RK Multidiameter （7420）

Technical Data:

Flange drilled to EN1092-2



Design features:The connector is made from ductile iron.

The EPDM gasket enable easy slide pipe into connector and make provision

for good contact to a pipe

even in places with light defects, unevenness, corrosion pits.




Application: Connection lines on straight end of pipes: cast iron, iron, asbestos-cement,


Assembly:






Dimensions

DN Dz L DN Dz L

[mm] [mm]

50 40-75205

300 310-350/350-390 290/320

60/65 60-95 350 395-435 290/320

80 80-115245

400 400-435/435-470/470-505 300/330/ 340

100 105-135 450 455-490/490-525 300

125 130-165

275

500 505-540/540-575/575-610 250/325/ 325

150 155-195600

610-645/645-680250/330/ 330

175 190-230 680-715

200 215-258 700 710-745 250

225 240-280 290 800 810-845 250

250 235-275 /270-310 290/320

No. Parts Materials

1 BodyDuctile Iron EN-GJS-500-7

2 Flange


4 Screw Galvanized Steel;S.S304/316

5 Nut Galvanized Steel;S.S304/316

6 Washer Galvanized Steel;S.S304/316

Material List


Quick Flange Adaptor For PE or PVC pipe COUPLING7510-rubber seal,7520-Brass ring

DESCRIPTION

Flange acc.to PN-EN1092-2,PN10 or PN16

(Other request on avaliable)

Pressure, PN10/PN16

Working temperature 70 ℃

The Brass ring make assembly easy and quickly.

The messing clamp ring hold and protect against moving a pipe.

All parts are protected against corrosion

Coating-Epoxy RAL5005-250μm

Application to PVC and PE pipe line.

STABDARD TYPE RESTRAINED TYPE

No. Parts Materials

1 BodyDuctile Iron GGG50

2 Flange

3 Rubber Ring EPDM/NBR

4 Sealing Ring Brass

Material List

OD Flange(PN10 or PN16) L

50 40 50

63 60/65 50

75 65 55

90 80 60

110 100 65

125 125 70

140 125 70

160 150 80

180 150 85

200 200 90

225 200 95

250 250 105

280 250 110

315 300 120

355 300 130

400 400 140

Dimensions (mm)


JOINTSSADDLE （7800）

No Reference Material standard

1 Body Ductile iron GGG50 EN1563

2 Cover Ductile iron GGG50 EN1563

3 Gasket EPDM/NBR EN681/EN682

4 Washer S.S A2;Galvanized steel

5 Bolt S.S A3;Galvanized steel

Material List

DN 3/4" 1" 1-1/4" 1-1/2" 2"

50 1.65 1.65 1.7 1.7 /

63 1.9 1.9 2 2 2

75 2.55 2.55 2.75 2.75 2.8

90 2.75 2.75 2.8 2.8 2.9

110 4 4 4.1 4.1 4.1

125 4.85 4.85 4.9 4.9 4.95

140 6.3 6.3 6.3 6.3 6.3

160 7.4 7.4 7.5 7.5 7.6

180 9.7 9.7 9.7 9.7 9.7

200 11.25 11.25 11.5 11.5 11.5

225 12.5 12.5 12.5 12.5 12.5

250 12.6 12.6 12.6 12.6 12.6

315 14 14 14 14 14

Dimensions (Inch)


Repair Clamps（7710-SS,7720-DI） JOINTS

序号 NO

部件名称 Parts

材质 Material

1外壳 Out case

S.S.304，316，201

2橡胶密封 Rubber Sealing Cylinde

EPDMfor water,air,powdered dust and ordinary steam

NBRnatural gas,air,gasonline and other hydrocarbonate

SiliconeAnti-sunexposure, anti-high temperature, Temperature-insulated

VitonAnti-heat,Anti-chemical corrossion

Gore-texAnti-heat,Anti-chemical corrossion

3,4螺栓、螺母 Bolts & Nut

S.S.304/316/201,Galvanized Steel

5垫片 Washer

S.S.304/316/201,Galvanized Steel

6扣板 Buckle

S.S.304/316/201

7导向挡板 Deflector

S.S.304/316/201

8支撑板 Backpanets

S.S.304/316/201;GGG40

9前护板 Front Tenders

S.S.304/316/201


WATERMETERBOX- 9100, COPPER ACCESSARIES-9200

TYPE 1:

TYPE 2:

ITEM NO DESCRIPTION

1 KEY

2LID OF THE METER BOX WITH LOCK SYSTEM

3 METER BOX

4+5+6 OUTPUT NIPPLE

7+8+9+10 EXPANSION JOINT

11+12+4 INLET NIPPLE with BALL VALVE

Size DN15

Item MJ15

L190

L1 302

L2 345

D G3/4B

d R1/2

H1 45

H 138

W 195

Dimensions

真诚打造信誉·追求更高品位 青岛迪维希机械有限公司 · f2f length to en558,iso...

Documents

真诚打造信誉·追求更高品位青岛迪维希机械有限公司 · f2f length to en558,iso...