this page1].pdf · 2011-02-26
TRANSCRIPT
SUNG CHANG CO., LTD.SUNG CHANG CO., LTD.SUNG CHANG CO., LTD.
GASKET &GLAND PACKING
2 │ http://www.scgasket.co.kr
sung chang co.,ltd.│ 3
조인트시트 제품
일반 범용 조인트 시트 (SC-7200)
고기능성 조인트 시트 (SC-7300)
고온용 조인트 시트 (SC-7500)
고온, 고압용 조인트 시트 (SC-7500W)
수지제품
테프론 시트 P.T.F.E 시트 (SC-8000)
P.C.T.F.E (SC-8001)
P.O.M (SC-8002)
P.E.E.K (SC-8003)
소프트 테프론 시트
(SC-8100H, SC-8100S)
테프론 가스켓 (SC 8201)
테프론 톱니형 가스켓 (SC 8202)
충전제 함침 테프론 시트
(SC-8300, SC-8400, SC-8500)
이피론 가스켓 (SC-8700)
테프론 쿠션 가스켓(SC-8601~8604)
테프론 조인트 씰란트 (SC-8800)
그라파이트 제품
그라파이트 시트 (SC-9000계열)
그라파이트 테이프 (SC-9700)
그라파이트 몰드 패킹 (SC-9800)
가스켓용 시트 제품
유지시트 (SC-4500)
콜크시트 (SC-4700)
고무판 (SC-6200~6700)
메탈 가스켓 제품
스파이럴 운드 가스켓 (SC-5000~5300)
메탈 자켓 가스켓 (SC-5400, 5401)
톱니형·평형 가스켓 (SC-5500)
링조인트 메탈 가스켓 (SC-6500)
기술자료
조인트 시트 사용상의 주의사항
가스켓 시트의 기본너비
가스켓 재료의 접촉면
07 ────────────────
08 ────────────────
09 ────────────────
10 ────────────────
11 ────────────────
12 ────────────────
13 ────────────────
14 ────────────────
15 ────────────────
16 ────────────────
16 ────────────────
17 ────────────────
18 ────────────────
18 ────────────────
19 ────────────────
20 ────────────────
21 ────────────────
21 ────────────────
22 ────────────────
22 ────────────────
23 ────────────────
27 ────────────────
29 ────────────────
30 ────────────────
31 ────────────────
32 ────────────────
33 ────────────────
34 ────────────────
JOINT SHEET
COMPRESSED GENERAL JOINT SHEET
COMPRESSED PREMIUM JOINT SHEET
COMPRESSED HIGH-TEMP JOINT SHEET
COMPRESSED HIGH TEMP - PRESSURE JOINT SHEET
PLASTIC
POLY TETRA FLUORO ETHYLENE
POLY CHLORO TRIFLUORO ETHYLENE
POLY OXY METHYLENE
POLY ETHER ETHER KETONE
SOFT PTFE SHEET
PTFE solid gasket
PTFE serration gasket
SPECIAL PTFE SHEET
PTFE + EPDM GASKET
PTFE CUSHION GASKET
PTFE JOINT SEALANT
GRAPHITE
GRAPHITE SHEET
GRAPHITE TAPE
GRAPHITE MOLD PACKING
SHEET
OIL PAPER SHEET
CORK SHEET
CR, NBR, EPDM, SBR, SILICONE, URETHANE
METAL GASKET
SPIRAL WOUND GASKET
METAL JACKET GASKET
SERRATED·FLAT METAL GASKET
RING JOINT METAL GASKET
TECHNICAL DATA
Guide for using gaskets
standard Width
Gasket material
4 │ http://www.scgasket.co.kr
그랜드 패킹 제품
윤활유입 테프론함침 면섬유 팩킹
(SC-1000)
윤활유입 테프론함침 아크릴섬유 팩킹
(SC-1100)
테프론섬유 편조 팩킹 (SC-1200)
윤활유입 테프론섬유 편조 팩킹
(SC-1200L)
흑연입 테프론섬유 팩킹 (SC-1300)
윤활유입 테프론함침 탄화섬유 팩킹
(SC-1400)
윤활유입 테프론함침 탄소섬유 팩킹
(SC-1500)
윤활유입 테프론함침 아라미드섬유 팩킹
(SC-1600)
인코넬선입 그라파이트섬유 팩킹
(SC-1700)
테프론함침 그라파이트섬유 팩킹
(SC-1800)
그라파이트섬유 팩킹 (SC-1900)
해치카바 팩킹 (SC-2000)
기술자료
취급상의 주의사항
압력에 의한 RING 패킹의 수
(밸브, 펌프)
스템과 패킹 폭과의 관계
축 흔들림의 허용치
재료별 PH 적용범위
그랜드 패킹의 사고원인별 분류
그랜드 패킹의누설대책
(회전 펌프용)
그랜드팩킹의 열람표
회전펌프 축용 그랜드 패킹 선정표
기기용 그랜드 패킹 선정표
치수표
36 ────────────────
36 ────────────────
37 ────────────────
37 ────────────────
38 ────────────────
38 ────────────────
39 ────────────────
39 ────────────────
40 ────────────────
40 ────────────────
41 ────────────────
41 ────────────────
42 ────────────────
44 ────────────────
44 ────────────────
44 ────────────────
45 ────────────────
46 ────────────────
47 ────────────────
47 ────────────────
48 ────────────────
49 ────────────────
50 ────────────────
GLAND PACKING
COTTON FIBER IMPREGNATED
WITH PTFE BRAIDED PACKING
ACRYLIC FIBER IMPREGNATED
WITH PTFE BRAIDED PACKING
PURE PTFE BRAIDED PACKING
PTFE WITH LUBRICATE DIPPED BRAIDED PACKING
PTFE GRAPHITE BRAIDED PACKING
CARBONIZED FIBER IMPREGNATED
WITH PTFE BRAIDED PACKING
CARBON FIBER IMPREGNATED
WITH PTFE BRAIDED PACKING
ARAMID FIBER IMPREGNATED
WITH PTFE BRAIDED PACKING
INCONEL WIRE-REINFORCED FLEXIBLE
GRAPHITE BRAIDED PACKING
GRAPHITE FIBER IMPREGNATED WITH
PTFE BRAIDED PACKING
FLEXIBLE GRAPHITE BRAIDED PACKING
HATCH COVER PACKING
TECHNICAL DATA
Handling Procedure
RING PACKING Q’ty according to pressure
(VALVE, PUMP)
Relation Between Stem and Packing Width
Maximum tolerance of stem wavering
pH Range of Packing Material
Failure causes of gland packings
Troubleshooting for the leakage of gland packing
(ROTARY PUMPS)
Use and Efficiency chart of GLAND PACKING
GLAND PACKING For shaft of Rotary pump
GLAND PACKING For instruments
measurement chart
sung chang co.,ltd.│ 5
6 │ http://www.scgasket.co.kr
Characteristic Use
Application Standards
ASTM F 104 P116A
JIS R 3453 CLASS 2
KS L 5406 CLASS 2
Standard Size
sung chang co.,ltd.│ 7
( Unit : mm )
Thickness
Size
0.5, 0.8, 1.0, 1.5, 2.0, 3.0, 5.0
1500 × 1500
1500 × 4500
Temperature : 200℃ Max
Pressure : 25㎏·f/㎠ Max
Water : below 20㎏·f/㎠′150℃
Oil : below 20㎏·f/㎠′150℃
Gass : below 10㎏·f/㎠′150℃
사용유체 : 에어, 물, 기름, 약산 및알칼리, 불활성
가스, 연료, 해수, 윤활유등
Applicable fluids : air, water, oil, weak acid and
alkali, inert gas, fuel, seawater,
lubricants, etc.
SC 7200
일반범용조인트시트COMPRESSED GENERAL JOINT SHEET
특수한내열성섬유및내유성고무를주된성분으로혼합하여
압착시킨 가스켓 시트로 내유성을 가진 일반 범용 비석면
조인트시트이다.
본 제품은 휨 및 유연성이 탁월하고 윤활유, 동물성 기름,
식물성 기름, 유기용제 등과 같은 광범위한 유체의 씰링에
적합한가스켓시트이다.
General purpose non-asbestos joint sheet of oilresistance as gasket sheet mixed and compressed withmajor ingredients of specific thermostable fiber and oilresisting rubber.This product has superior bending property and flexibilityas gasket sheet suitable for sealing of wide-ranged fluidsuch as lubricants, animal oils, vegetable oils and organicsolvents, etc.
Characteristic Use
Application Standards Standard Size
ASTM F 104 P116A
JIS R 3453 CLASS 2
KS L 5406 CLASS 2
8 │ http://www.scgasket.co.kr
( Unit : mm )
Thickness
Size
0.5, 0.8, 1.0, 1.5, 2.0, 3.0, 5.0
1500 × 1500
1500 × 4500
고품질의 내열성 섬유 및 내유성 고무를 사용했기 때문에
특히 기름에 안정적이며 휨 및 유연성이 탁월하고 복원력이
좋아밀봉성이아주우수한고기능성조인트시트입니다.
Because of high quality thermostable fiber and oilresisting rubber, the product is stable especially for oil asa high performance joint sheet of very excellent sealingability as it has superior bending property and flexibility aswell as very good force of restitution.
Temperature : 250℃ Max
Pressure : 30㎏·f/㎠ Max
Water : below 25㎏·f/㎠′200℃
Oil : below 20㎏·f/㎠′150℃
Gass : below 15㎏·f/㎠′150℃
사용유체 : 에어, 물, 기름, 약산 및알칼리, 불활성
가스, 연료, 해수, 윤활유등
Applicable fluids : air, water, oil, weak acid and
alkali, inert gas, fuel, seawater,
lubricants, etc.
SC 7300
고기능성조인트시트COMPRESSED PREMIUM JOINT SHEET
Characteristic Use
Application Standards
ASTM F 104 P1161A
JIS R 3453 CLASS 2
KS L 5406 CLASS 2
Standard Size
sung chang co.,ltd.│ 9
( Unit : mm )
Thickness
Size
0.5, 0.8, 1.0, 1.5, 2.0, 3.0, 5.0
1500 × 1500
1500 × 4500
SC/#7500 조인트 시트는 다른 비석면 가스켓시트 보다 더
효과적으로 씰링 되도록 특별히 고안된 제품으로 특히 아라
미드섬유가 첨가된 유연성 그라파이트와 NBR 바인더의
독창적인 혼합으로 탁월한 내열성과 원상 복원력을 가진
제품이다.
As a specially designed product for much more efficientsealing than other non-asbestos gasket sheets,SC/#7500 Joint Sheet is a product made of very uniquemixture with flexible graphite added aramid fiber and NBRbinder to have excellent thermal resistance as well asvery good force of restitution to the original state.
Temperature : 300℃ Max
Pressure : 35㎏·f/㎠ Max
Water : below 30㎏·f/㎠′250℃
Oil : below 25㎏·f/㎠′200℃
Gass : below 20㎏·f/㎠′200℃
사용유체 : 스팀, 에어, 물, 기름, 약산 및알칼리,
불활성가스, 연료, 소금용액, 윤활유등
Applicable fluids : steam, air, water, seawater, oil,
weak acid and alkali, inert gas,
fuel, isolated engine system,
lubricants, etc.
SC 7500
고온용조인트시트COMPRESSED HIGH-TEMP JOINT SHEET
10 │ http://www.scgasket.co.kr
Characteristic Use
Application Standards Standard Size
ASTM F 104 P1161A
JIS R 3453 CLASS 2
KS L 5406 CLASS 2
( Unit : mm )
Thickness
Size
1.0, 1.5, 2.0, 3.0, 5.0
1500 × 1500
1500 × 4500
SC/#7500-W 비석면 시트는 #7500시트와 동일한 재질의
혼합 바인더에다 스텐레스 금망을 삽입하여, 보다 뛰어난
내열성과 원상 회복력을 가짐으로 주로 스팀용 또는 엔진
폐기관등고온, 고압용으로개발된조인트시트입니다.
As stainless steel wire net inserted into compact binder ofthe same material as #7500 sheet, SC/#7500-W non-asbestos sheet has much better thermal resistance andforce of restitution to the original state so that this productis a joint sheet developed for main application of hightemperature/pressure such as steam or isolated enginesystem, etc.
Temperature : 350℃ Max
Pressure : 60㎏·f/㎠ Max
Water : below 35㎏·f/㎠′300℃
Oil : below 30㎏·f/㎠′250℃
Gass : below 25㎏·f/㎠′200℃
사용유체 : 스팀, 에어, 물, 해수, 기름, 약산 알칼리,
불활성가스, 연료, 엔진폐기관, 윤활유
등
Applicable fluids : steam, air, water, seawater, oil,
weak acid and alkali, inert gas,
fuel, isolated engine system,
lubricants, etc.
고온, 고압용조인트시트COMPRESSED HIGH TEMP - PRESSURE JOINT SHEET
SC 7500-W
sung chang co.,ltd.│ 11
Characteristic Use
Temperature : -200 ~ 260℃ Max
Standard Size
( Unit : mm )ROLLSHEET
Thickness
Width
Length
0.5, 0.8, 1.0, 1.5, 2.0, 3.0
300, 1000, 1200, 1500, 2000
10M (M단위절단가능)10M (possible to cut in M unit)
( Unit : mm )ROD, PIPE
Dia
Length
Ø5 ~ Ø250
300 or 1000
( Unit : mm )PLATE
Thickness
W × L
4, 5, 6, 7, 8, 9, 10, 15, 20
1000 × 1000 ~ 2000
PTFE SHEET는 우수한 화학안정성과 저마찰, 전기적 특성이
탁월하며 특히 내약품성은 유기재료 중에서 산, 알카리등
각종 용재에 전혀 침해가 되지않는 우수한 성질을 가지고
있습니다.
내산용 GASKET, 패킹, 전기절연재등 광범위하게 사용되어
집니다.
SHEET외 봉, 파이프 튜브와 몰드에 의한 다양한 형태의
제품이생산되고있습니다.
PTFE sheet has excellent chemical stability and lowerfriction as well as superior electric characteristics andexpecially about chemical resistance, this product hasvery good property of never being penetrated by varioussolvents such as acid, alkali among organic materials.Widely used for acid resisting gasket, packing and electricinsulating material.Also manufactured in shapes of rod, pipe, tube as well asin various shapes by molds.
SC 8000
테프론시트 (SOLID PTFE SHEET)POLY TETRA FLUORO ETHYLENE
SC 8001
PCTFEPOLY CHLORO TRIFLUORO ETHYLENE
12 │ http://www.scgasket.co.kr
FEATURE Use
Standard Size
Characteristic
( Unit : mm )
ROD
PLATE(T)
W × L
Ø5~Ø50 / 1000L
Ø20~Ø100 / 300~500L
5 ~ 100T
200 ×200, 300 ×300, 500 ×500
PCTFE는 불소수지류의하나로서사출이나압출, 압축등으로
성형하여임의의형상으로가공이가능한제품입니다.
PTFE와 마찬가지로 내약품성이 뛰어나고 내열성과 투명성도
지니고있습니다.
As a kind of Fluorine resin, PCTFE is a product
available to be processed in any shape by molding
of injection, extrusion and compression, etc. Like
PTFE, this product has excellent chemical resistance
as well as thermal resistance and transparency.
-240 ~ 150℃ 까지의 내열성을 가져 치수 안정성과 내충
격성이뛰어나며극저온용으로적합합니다.
강산, 강알카리등산화제에강하다.
투명하여용기, 파이프등에액체확인이용이하다.
PTFE보다압축힘이뛰어나화학용가스켓으로많이이용된다.
The product of excellent dimensional stability and
shock resistance due to thermal resistance from -
240 to 150℃, and also suitable for extremely low
temperature.
Strong against oxidizers such as strong acid and
strong alkali, etc.
Because of transparency, easy to check about fluids
in container, pipe, etc. Due to stronger compression
power than PTFE, generally used for chemical
gasket.
내열성 전기부품, 패킹, 라이닝재료, 화학 기계 배관, 레벨
게이지, 화학용고압가스켓, 밸브패킹
Thermal resisting electric parts, packings, lining
materials, chemical machinery pipes, level gauges,
chemical high pressure gaskets, valve packings
SC 8002
POMPOLY OXY METHYLENE
sung chang co.,ltd.│ 13
FEATURE Use
Characteristic
( Unit : mm )
ROD
PLATE (T)
W × L
Ø5~Ø250 (1000~3000)
5 ~ 50T
1000 × 1000 ~ 3000
대표적인 엔지니어링 플라스틱으로 유리전이 온도가 약
-60℃이기 때문에 사용온도범위 내에서 기계적 성질의 온도
의존성이큰수지입니다.
P.O.M은 결정성이 높은 수지로 인성 및 강성의 조화가 뛰어난
것이큰장점이며내마모, 마찰성또한우수합니다.
As a representative engineering plastic, it is a resin ofhigh dependence on temperature regarding mechanicalcharacteristics within the temperature range to usebecause of the glass transition temperature which isabout -60℃. As a resin of high crystallization, ... has agood merit of excellent harmony of tension and strengthand also its abrasion resistance as well as frictionresistance are very good.
-60 ~ 90℃ 까지의 내열성이므로 무기약품류에 내구성이
좋다.
지속적인충격이나진동에도안정된성능을유지한다.
열가소성 수지중에서 내마찰, 마모성이 가장 뛰어나고 자체
윤활성이있어윤활제없이사용되는제품에적합하다.
Good durability against inorganic chemicals due to itsthermal resistance from -60 ~ 90℃.Maintains stable performance even under constant shockor vibration.The best product regarding friction resistance andabrasion resistance among thermoplastic resins, which issuitable for products using without lubricant because of itsown lubricative property.
각종전자부품및가전제품, 자동차부품에사용
Applicable for various kinds of electronic parts and homeappliances as well as automotive parts
Standard Size
14 │ http://www.scgasket.co.kr
FEATURE Use
Standard Size
Characteristic
( Unit : mm )
ROD
PLATE(T)
W × L
Ø5~Ø200 (1000)
5 ~ 60T
510, 610 × 1000 ~ 3000
PEEK는 내열성, 내약품성이뛰어난고기능성수지제품으로
250℃까지는연속사용이가능합니다.
강성과신장율도크며내충격성이뛰어난강인한제품입니다.
As a high performance resin product, PEEK has excellentthermal resistance and chemical resistance and possibleto use continuously up to 250℃. A tough product of good strength and elongation as wellas excellent shock resistance.
고온(250℃)에 연속사용가능
뛰어난내약품성
고온, 고압에서도물성의변화가거의없다.
전기적특성, 내후성이뛰어나다.
Possible to use continuously under high temperature(250℃).Excellent chemical resistance.Almost no change in property of matter even under hightemperature, high pressure.Excellent electric characteristics and weatherability.
정밀기기부품, 식품라인, 자동차, 항공기 부품, 원자력 관련
설비, 열수, 스팀 밸브, 펌프, 배관등의부품
Applicable for precision instrument parts, parts for foodlines, automobiles and aircraft,parts for facilities related to nuclear energy, hot water &steam valve, pump and pipes
SC 8003
PEEKPOLY ETHER ETHER KETONE
소프트테프론시트-SSOFT PTFE SHEET-S
sung chang co.,ltd.│ 15
Use Standard Size
Characteristic
( Unit : mm )
Thickness
Width
Length
1.0, 1.5, 2.0, 3.0
1250
10M (M단위절단가능)
일반적인 PTFE SHEET보다 내화학성과 내열성을 높이고 퍼짐현상(CREEP)에
대한 막힘현상(COLD FLOW)을 현저히 줄인 PTFE SHEET이며 일반 PTFE에
비해 경도가 낮아 훨씬 부드러운 성질을 가짐으로서 대구경 또는 정밀가스켓
가공시훨씬유리합니다.
As PTFE sheet of higher chemical resistance and thermal resistance aswell as remarkably lower creep and cold flow than general PTFE sheet, theproduct of much softer property than general PTFE sheet because of lowerhardness, which is much more profitable in working of larger diameter orprecision gasket.
Temperature : -200 ~ 260℃
산, 알카리, 저온유체, 부식성유체, 오염 위험유체에사용
Applicable for acid, alkali, lower temperature fluids,corrosive fluids, dangerous fluids of contamination
소프트테프론시트-HSOFT PTFE SHEET-H
SC 8100-H
Use Standard Size
Characteristic
( Unit : mm )
Thickness
Width
Length
1.0, 1.5, 2.0, 3.0
1500
1500
SC 8100-H와 같은 성능을 가지면서 경도를 더 낮추어 고르지 못한 플렌지
면에도탁월한접합성으로빈틈없는씰링이가능합니다.
가스켓 사이즈가 대 구경일 경우 장착시 가스켓 위치 조정에 약간의 어려움은
있으나씰링성은우수합니다.
The product of same performance but lower hardness than Soft PTFE-H,which is possible to make compact sealing by excellent weldability evenonto uneven flange surface. A bit difficult for adjustment of gasket positionin the installation for gasket in larger diameter but very good sealingperformance.
Temperature : -200 ~ 260℃
산, 알카리, 저온유체, 부식성유체, 오염 위험유체에사용
Applicable for acid, alkali, lower temperature fluids,corrosive fluids, dangerous fluids of contamination
SC 8100-S
SC 8201
테프론가스켓PTFE SOLID GASKET
SC 8202
16 │ http://www.scgasket.co.kr
Use
Characteristic
내화학성이우수한 PTFE SHEET를 소정의평면상으로타발
가공한 가스켓입니다. 충전제로 Carbon이나 Glass등을
함침하여사용범위를높인제품도생산됩니다.
Temperature : -200 ~ 260℃
산, 알카리, 저온유체, 부식성유체, 오염 위험유체에사용
Applicable for acid, alkali, lower temperature fluids,corrosive fluids, dangerous fluids of contamination 사이즈는배관규격에준하며그외치수도가능하다.
Size conforms to pipe specifications.
Use
Characteristic
일반적인 테프론 가스켓에 주름 가공을 하여 마찰면의 압력을
높인가스켓으로압력이다소높은 LINE에 사용됩니다.
Temperature : -200 ~ 260℃
산, 알카리, 저온유체, 부식성 유체, 오염 위험 유체에 사용되며
Chemical 운반선등에많이사용된다.
Applicable for acid, alkali, lower temperature fluids,corrosive fluids, dangerous fluids of contamination
사이즈는배관규격에준하며그외치수도가능하다.
Size conforms to pipe specifications.
테프론톱니형가스켓PTFE SERRATION GASKET
충전제함침테프론시트SPECIAL PTFE SHEET
sung chang co.,ltd.│ 17
Use
Standard Size
Temperature : -200 ~ 260℃
Characteristic
( Unit : mm )
THICKNESS
W × L
1.0, 1.5, 2.0, 3.0
1500 × 1500
물리적특성Physical Characteristics
Test Method
SC-8500
SC-8400
SC-8500
색상 Color
충전제 Range of Filler
PH Range
사용압력 Use Pressure
사용온도 Use Temperature
P×T
(bar×℃)
압축율 Compressibility
복원율 Restoring Rate
인장강도 Tension Strength
밀도 Density
creep 완화율
creep Relaxation Rate
누출 Leakage
≥30
1.5mm
3.0mm
ASTM F 36A
ASTM F 36A
ASTM 152
ASTM D 792
ASTM F 38
ASTM F 37 A
Fawn
PTFE+SILICA
0-14
83
-200~260
12000
8600
7-12
40
14
2.1
18
Blue
PTFE+GLASS
0-14
55
-200~260
12000
8600
30
14
1.7
40
0.12
Off white
PTFE+BARIUM
0-14
83
-200~260
12000
8600
4-10
40
14
2.9
11
SC-8500
SC-8400
SC-8300
강산(플로루화수소산제외), 솔벤트, 탄화수소,물, 스팀 염소 및 극저온 메체 FDA 규정에
부합
Strong acid (except of Hydrofluoric acid),solvent, hydrocarbon, water, steam,chlorine and extremely low temperaturemedia, suitable for FDA regulations
적절한 농도의 산 및 일부 부식제, 솔벤트,탄화수소, 물, 냉각제 및 극저온 매체 FDA
규정에부합
Proper concentration acid and somecorrosive, solvent, hydrocarbon, water,coolant and extremely low temperaturemedia, suitable for FDA regulations
부식제, 산, 염소, 가스, 스팀, 탄화수소 및
극저온매체, FDA 규정에부합
Corrosive, acid, chlorine, gas, steam,hydrocarbon and extremely lowtemperature media, suitable for FDAregulations
일반적인 PTFE에서 자주 발생하는 막힘현상이나 퍼짐현상을
개선완화시키기위해일반 PTFE 성분에무기질의충전제를
배합하여 특수 제조된 테프론 시트로 용도에 따라 3가지의
종류가있습니다.
고농도의열황산, 열초산등각종화학약품에적합합니다.
Teflon sheet specially manufactured by mixture ofinorganic fillers into general PTFE ingredients to improveor reduce cold flow or creep being happened frequentlyregarding general PTFE and 3 kinds of products availableaccording to the use.Suitable for various chemicals such as high concentrationsulphuric acid and nitric acid, etc.
SC 8300, 8400, 8500
테프론쿠션가스켓PTFE CUSHION GASKET
SC 8700
이피론가스켓PTFE + EPDM GASKET
18 │ http://www.scgasket.co.kr
Use
Characteristic
Temperature : -40 ~ 150℃
Standard Size
사이즈는배관규격에준한다.
Size conforms to pipe specifications.
Use
Characteristic
Standard Size
그라파이트, 비석면시트, 고무 등선택가능 Optional use of non-asbestos sheet or rubber, etc.
SC-8601
SC-8602
SC-8603
SC-8604
A-TYPE
C-TYPE
D-TYPE
밀폐용For airtight
PTFE
중심재
고무의 복원력과 PTFE의 내산성을 겸하는 SEAL성이 우수한
가스켓으로 PVC 배관이나 GLASS LINNING 배관과 같은
볼트조임의힘이많이걸리지않는곳에적합합니다.
As a gasket of excellent sealing performance combinedrestoring power of rubber with acid-resistant of PTFE,suitable to use for portions loaded less power of bolttightening such as PVC pipe or glass lining pipe.
탄력성이 있는 중심재를 얇은 PTFE 박판 피복하여 만든
가스켓으로 내산성을 가지면서 중심재에 의해 낮은 면압으로도
밀봉이되는경제적인제품입니다.
Gasket made as PTFE thin plate coated onto the flexiblecenter material of acid resistance and also economical asit can be sealed just by low surface pressure due to thecenter material.
Temperature : -50 ~ 150℃
Pressure : •A-Type : 5 ~ 16k •C,D-Type : 5 ~ 20k
산, 알카리, 저온유체, 부식성유체, 오염 위험유체에사용
Applicable for acid, alkali, lower temperature fluids,corrosive fluids, dangerous fluids of contamination
SC 8601 ~ 8604
SC 8800
테프론조인트실란트PTFE JOINT SEALANT
sung chang co.,ltd.│ 19
Characteristic
Use
Temperature : -200 ~ 240℃
3mm × 2.0T × 30M
5mm × 2.5T × 20M
7mm × 3.5T × 15M
9mm × 4.0T × 8M
13mm × 4.5T × 4.5M
16mm × 6.0T × 4.5M
19mm × 6.5T × 4.5M
25mm × 7.0T × 4.5M
오발형
Oval type
JOINT SEALANT GASKET TAPE ZIP JOINT
25mm × 1.5T × 20M
30mm × 1.5T × 20M
40mm × 1.5T × 20M
50mm × 1.5T × 20M
25mm × 3.0T × 20M
30mm × 3.0T × 20M
40mm × 3.0T × 20M
50mm × 3.0T × 20M
Ø3 × 30M
Ø4 × 20M
Ø5 × 15M
Ø6 × 10M
Ø8 × 10M
Ø10 × 10M
Ø13 × 10M
Ø15 × 10M
테이프형
Tape type
오형
O type
PTFE 조인트 실란트는 PTFE의 내산성과 내열성의 성질을
그대로 가지고 있는 띠 형태의 FREE 사이즈 씰 재료입니다.
긴급하고 손쉽게 모든 사이즈에 사용이 가능한 아주 효과적인
제품입니다.
PTFE joint sealant as a free sized sealing material in theshape of tape which has all the properties of PTFE, suchas acid-resistance and thermal resistance. Very effectiveproduct available to use immediately and easily for allsizes.
1. Wipe clean the surface area to be installed. 2. Remove film from double faced adhesive tape on the
back of the product and after grounding onto the area to be installed, cross the ends.
3. Fasten bolts.
1. 장착하고자하는표면부위를깨끗이닦아냅니다.
2. 제품의뒷면에있는양면점착 TAPE의 막을떼어내고
장착부위에접지한후끝단부위를교차시켜줍니다.
3. 볼트를체결해줍니다.
사사용용방방법법
SC 9000
그라파이트시트GRAPHITE SHEET
20 │ http://www.scgasket.co.kr
Use
Characteristic
Standard Size
( Unit : mm )
Thickness
Size
0.5, 1.0, 1.5, 2.0, 3.0
1000 × 50M (0.5)
1000 × 1000 (1.0 ~ 3.0)
1500 × 1500 (1.5 ~ 3.0)
SC No.
SC-9000
SC-9100
SC-9200 - Tang
SC-9200 - Mesh
SC-9300 - Tang
SC-9300 - Mesh
내장재재질 Material of interiors
CS
304
304
316
316
내장재형태 Type of interiors
TANG
TANG
MESH
TANG
MESH
Characteristic
NO. SC-9000
Pure Graphite Sheet
NO. SC-9100, 9200, 9300
SUS Punching-Hole Insert
NO. SC-9200, 9300
SUS Mesh Insert
그라파이트 시트는 불순물을 전혀 포함하지 않은 천연인상
흑연을압착하여 SHEET화 한제품입니다.
내열성, 내약품성이우수하며유연성이뛰어납니다.
Graphite sheet as the product made as a sheet ofcompressed natural rosette graphite which does notcontain impurities at all.Excellent thermal resistance and chemical resistance aswell as very good flexibility.
고온고압에충분한밀봉효과를낼수있도록금속판양면에그라파이트시트를압착하여제작된제품이다.
The product made of graphite sheet compressed on both sides of metal plate for enough sealing effect under hightemperature and high pressure.
Temperature : -200 ~ 450℃
(Oxiding Atmosphere)
-200 ~ 1650℃
(Non-Oxiding Atmosphere)
고온, 고압의증기, 가스, 산, 알카리, 밸브본네트, 열교환기등
Steam of high temperature and high pressure, gas, acid,alkali, valve bonnet, heat exchanger, etc.
SC 9700
그라파이트테이프GRAPHITE TAPE
sung chang co.,ltd.│ 21
Characteristic
Use Standard Size
Temperature : -200 ~ 450℃( Unit : mm )
Thickness
Width
Length (M)
0.5T
12, 16, 19, 25
15
그라파이트 시트를 일정한 사이즈로 절단하여파형으로 주름
가공후한면을양면테이프로접착한제품입니다.
축에 감아 간단히 성형하여 사용하거나 가스켓 표면부위에
부착함으로서좀더나은씰링효과를볼수있습니다.
The product of which a graphite sheet was cut in auniform size and after crease processed in wave forms,double faced tape adhered to the one side.Better sealing effect as it used by a simple molding towind it on axis or adhere to a surface area of gasket.
그라파이트 시트를 소정의 치수로 압축성형한제품으로 흑연
특유의 자체 윤활성이 왕복 또는 회전축에 전혀 손상을 주지
않고 밀봉작용을 합니다. 사용온도 한계치가 크고 보수유지가
간단합니다.
Compressed molding product of graphite sheet and dueto its own lubricative property specific to graphite takes,sealing effect with no damage to reciprocating or rotatingaxis. Wider range of limits to use temperature and simplefor maintenance and repair.
Temperature : -200 ~ 450℃
고온, 고압 및극저온의밸브, 펌프등에널리사용
Applicable for general use of high temperature, highpressure valves and pumps, etc.
금형제작가공품이므로별도상담바랍니다.
This product is made by molding process and needsspecial consultation.
그라파이트몰드패킹GRAPHITE MOLD PACKING
SC 9800
Use
Characteristic
콜크시트 (내유용)CORK SHEET
SC 4500
유지시트OIL PAPER SHEET
SC 4700 ((내내유유))
22 │ http://www.scgasket.co.kr
Temperature : 120℃
( Unit : mm )
Length
(Roll / m)
Thickness
Width
0.15, 0.25, 0.5, 0.8, 1.0, 1.6
1000
0.15T × 250M
0.25T × 200M
0.5T × 150M
0.8T × 100M
1.0T × 50M
1.6T × 50M
M 단위절단가능
섬유소에 합성젤라틴을 함침시킨 내유시트 제품입니다. 종이
성질을 가지고 있기 때문에 압력과 온도에는 약하나 내유성
이 높고 가공성이 좋아 기계장치 접합부 GASKET용으로
많이 사용됩니다. Non-Asbestos Gasket에 비해 가격이
저렴합니다.
The product of oil resistance sheet made by syntheticgelatine impregnated into cellulose. Weak for pressureand temperature due to the property of paper butgenerally used for gasket of copula in machinery becauseof high oil resistance and good processability. Lower pricecompared to the one of non-asbestos gasket.
고무콜크는 뛰어난 압축성과 탄성을 가지고 있는 콜크에 복원력을
가진 고무를 합성함으로서 밸브 COVER, 타이밍 기어 COVER
등에가스켓으로유용하게사용됩니다.
Rubber cork made by cork of excellent compressibility andelasticity synthesized with rubber of force of restitution. Valuablyused as gasket for valve cover, timing gear cover, etc.
1. 냉각류누출방지용 (For prevention from leakage of cooling oil)
2. 기어박스 COVER (For gear box cover)
3. 밸브 COVER, 변속장치등 (For valve cover, transmission, etc.)
1. 비투과성이다.
2. 복원력이좋다.
3. 표면마찰력을가지고있다.
4. 내충격성을가지고있다.
5. 내유, 내열성이우수하며내절연성이양호하다.
1. Opaque2. Good force of restitution3. Surface friction4. Shock resistance5. Excellent oil resistance and thermal resistance, good
insulating oil resistance
( Unit : mm )
Thickness
Size
1.0 ~ 20
600 × 900 (1T)900 × 1800 (1.5T~20T)
Characteristic
Use
Standard Size
Characteristic
Use
Use
Standard Size
내열성고무CR (NEOPRENE)
sung chang co.,ltd.│ 23
1. Excellent weatherability, ozone resistance and aging by heat resistance.
2. Good oil resistance and chemical resistance. 3. Nonflammable. 4. Less transmissivity against GAS. 5. Excellent thermal resistance usable up to the
maximum 150°.
1. 내후성, 오존성, 열노화성에우수하다.
2. 내유성, 약품성이우수하다.
3. 난연성이다.
4. (GAS) 투과성이적다.
5. 내열성이우수하다. 최고 150℃까지사용.
1. Excellent weatherability and resistance of ozone, deterioration.
2. Thermal resistance usable up to 150°. 3. Freezing resistance usable up to -50°.4. Chemical resistance excellent for polar solvents. 5. Excellent for water vapor.
1. 오존성, 내후성, 노화성이우수하다.
2. 내열 150℃까지사용.
3. 내한성 -50℃까지사용.
4. 내약품성, 극성 용제에우수하다.
5. 수증기에우수하다.
내산성고무EPDM
1. Excellent oil resistance. 2. Good abrasion resistance. 3. Good aging by heat resistance. 4. Good chemical resistance. 5. Less transmissivity against GAS. 6. Excellent stress, degree of strength and hardness. 7. Excellent mixibility with PVC resin, etc.8. Bad winding, crack, ozone resistance, electric
insulating property and adhesive property.
1. 내유성(기름)이 우수하다.
2. 내마모성이좋다.
3. 열노화성이좋다.
4. 내약품성이우수하다.
5. (GAS)투과율이적다.
6. 응력, 강도, 경도는우수하다.
7. PVC 수지등혼합성이우수하다.
8. 굴곡, 균열, 오존성, 전기절연성, 접착성이나쁘다.
내유성고무NBR
SC 6200
SC 6300
SC 6400Characteristic
Characteristic
Characteristic
24 │ http://www.scgasket.co.kr
1. Excellent dynamic characteristics. 2. Excellent crack resistance. 3. Excellent abrasion resistance. 4. Excellent low temperature characteristics. 5. Excellent deterioration resistance.
1. 동적 특성이우수하다.
2. 균열 저항성이우수하다.
3. 내마모성이우수하다.
4. 저온특성이우수하다.
5. 내노화성이우수하다.
1. Thermal resistance usable up to 200°.(Silicon of high tear strength: Usable up to 300°).
2. Freezing resistance usable up to -90°.3. Excellent weatherability and ozone resistance. 4. Very good electric characteristics. 5. Weak degree of strength and chemical resistance.
1. 내열성 200℃까지사용.
(고인열실리콘 : 300℃까지사용가능)
2. 내한성 -90℃까지사용.
3. 내후성, 내오존성이우수하다.
4. 전기적성질이상당히우수하다.
5. 강도, 내약품성이약하다.
1. Excellent abrasion resistance. 2. Excellent tear strength. 3. Good resistance against low temperature, ozone and oil. 4. Weak for boiling water, water vapor and frictional heat. 5. Discolored by direct ray of light.
1. 내마모성이탁월하다.
2. 인열강도가우수하다.
3. 저온성, 오존성, 내유성은양호하다.
4. 끊는물, 수증기, 마찰열등에는약하다.
5. 직사 광선에변색한다.
내후성고무SBR
실리콘고무SILICONE
우레탄고무URETHANE
SC 6500
SC 6600
SC 6700
Characteristic
Characteristic
Characteristic
sung chang co.,ltd.│ 25
A : 매우적합 (Most suitable), B : 적합 (Suitable), C : 보통 (Moderate), D : 부적합 (Unsuitable)
종류Kinds
화학구조Chemical structure
경도범위 Range of hardness
인장강도 Tension strength(㎏/㎠)
신장률 Elongation(%)
반발탄성 Elastic rebound
인열강도 Tear strength
내마모성 Abrasion resistance
내굴곡성 Winding and crack resistance
내열성 Thermal resistance(℃)
내한성 Freezing resistance(℃)
내노화성 Deterioration resistance
내오존성 Ozone resistance
내염성 Salt-tolerant
전기절연Ω-cm Electric insulation
내GAS투과성 Transmissivity resistance against GAS
가솔린, 경유 Gasoline, Light oil
벤젠, 톨루엔 Benzene, Toluene
트리클렌 Trichloroethylene
알코올 Alcohol
에테르 Ether
케톤 Ketone
초산 Nitric acid
물 Water
유기산 Organic acid
고농도무기산 High concentration inorganic acid
저농도 무기산 Low concentration inorganic acid
고농도 알카리 High concentration alkali
저농도 알카리 Low concentration alkali
물리적성질
내유
내용제성
내산
알카리성
특징Characteristic
고탄성High elasticity
기계적성질이좋음Excellent mechanic
characteristics
10 ~ 100
30 ~ 300
1000 ~ 100
B
B
B
B
120
-50 ~ -70
C
D
D
10
C
D
D
D
B
D
C
D
B
D
D
C
C
C
20 ~ 100
50 ~ 200
1000 ~ 100
B
C
B
B
120
-50 ~ -70
C
D
D
10 ~ 15
C
D
D
D
B
D
C
D
B
D
D
C
C
C
30 ~ 100
50 ~ 200
800 ~ 100
C
D
B
C
120
-30 ~ -60
C
D
D
10 ~ 15
D
D
D
D
B
D
C
D
B
D
D
C
C
C
30 ~ 100
20 ~ 200
800 ~ 100
A
C
B
D
120
-73
C
D
D
14 ~ 15
C
D
D
D
B
D
C
D
B
D
D
C
C
C
10 ~ 90
50 ~ 250
1000 ~ 100
B
C
C ~ B
C
130
-35 ~ -55
B
B
C
10 ~ 12
C
C
D
D
B
D
C
D
B
D
C
B
B
B
20 ~ 90
50 ~ 150
800 ~ 100
D
C
C
B
150
-30 ~ -55
B
B
D
16 ~ 18
B
D
D
D
B
D
B
B
B
D
B
B
B
B
천연고무에가까운성질Characteristics
close to natural
rubber
내마모성Abrasion resistance
내노화성Deterioration
resistance
양호Excellence
고탄성High elasticity
내마모성Abrasion
resistance
양호Excellence
내후성Weatherability
내열성Thermal resistance
내후성Weatherability
내오존성Ozone resistance
내GAS투과성Transmissivity resistance against
GAS
천연고무(NR)Natural Rubber
NaturalRubber
PolyIsoprene
StyreneButadien
PolyButadien
PolyChloroprene
IsobutyleneIsoprene
합성고무(IR)Synthetic Rubber
스티렌고무(SBR)Styrene Rubber
부타디엔고무(BR)Butadiene Rubber
네오프렌고무(CR)Neoprene Rubber
부틸고무(IIR)Buthyl Rubber
고무(RUBBER)의 특성비교COMPARISON IN CHARACTERISICS OF RUBBER
26 │ http://www.scgasket.co.kr
A : 매우적합 (Most suitable), B : 적합 (Suitable), C : 보통 (Moderate), D : 부적합 (Unsuitable)
종류Kinds
화학구조Chemical structure
경도범위 Range of hardness
인장강도 Tension strength(㎏/㎠)
신장률 Elongation(%)
반발탄성 Elastic rebound
인열강도 Tear strength
내마모성 Abrasion resistance
내굴곡성 Winding and crack resistance
내열성 Thermal resistance(℃)
내한성 Freezing resistance(℃)
내노화성 Deterioration resistance
내오존성 Ozone resistance
내염성 Salt-tolerant
전기절연Ω-cm Electric insulation
내GAS투과성 Transmissivity resistance against GAS
가솔린, 경유 Gasoline, Light oil
벤젠, 톨루엔 Benzene, Toluene
트리클렌 Trichloroethylene
알코올 Alcohol
에테르 Ether
케톤 Ketone
초산 Nitric acid
물 Water
유기산 Organic acid
고농도무기산 High concentration inorganic acid
저농도 무기산 Low concentration inorganic acid
고농도 알카리 High concentration alkali
저농도 알카리 Low concentration alkali
물리적성질
내유
내용제성
내산
알카리성
특징Characteristic
내유성Oil resistance
내마모성Abrasion resistance
내노화성Deterioration resistance
15 ~ 100
50 ~ 250
800 ~ 100
C
C
B
C
130
-10 ~ -20
B
D
D
2 ~ 10
C
B
D
D
B
D
D
D
B
D
D
C
C
C
30 ~ 90
50 ~ 200
800 ~ 100
C
D
C
C
150
-40 ~ -60
B
B
D
12 ~ 15
C
D
D
D
B
C
B
B
B
D
C
B
B
B
50 ~ 90
79 ~ 200
500 ~ 100
C
C
B
C
150
-20 ~ -60
A
A
B
14
B
C
D
D
B
D
C
D
B
D
B
B
B
B
60 ~ 100
200 ~ 450
800 ~ 300
B
A
A
B
80
-30 ~ -60
C
B
D
9 ~ 12
C
B
D
C
D
D
D
C
D
D
D
D
D
D
30 ~ 90
40 ~ 100
500 ~ 50
B
D
D
C
280
-70 ~ 120
B
B
C
11 ~ 15
D
D
D
C
B
D
C
D
C
C
D
C
B
B
50 ~ 90
70 ~ 200
500 ~ 100
D
C
B
C
300
-10 ~ -50
B
B
B
15 ~ 18
B
A
B
C
B
D
D
D
B
D
B
B
D
D
내산성Acid resistance
내노화성Deterioration resistance
내후성Wetherability
내약품성Chemical resistance
내노화성Deterioration resistance
내오존성Ozone resistance
기계적강도우수
Mechanical strength Excellence
내열성Thermal resistance
내한성Freezing resistance
내유성Oil resistance
내열성우수Excellent thermal resistance
내약품성Chemical resistance
니트릴고무(NBR)
Nitrile rubber
에치레프로펠렌(EPDM)
Ethylene propylene
하이파론(CSM)Hypalon
우레탄고무(U)
Urethane rubber
실리콘고무(Si)
Silicon rubber
불소고무(FPM)
Fluorine rubber
AcrylnitrileButadien
EtyleneButadien
PolyethleneSulfinated
PolyUrethane
Siloxane6불화
Fluoridationplopylene
고무(RUBBER)의 특성비교COMPARISON IN CHARACTERISICS OF RUBBER
sung chang co.,ltd.│ 27
스파이럴운드가스켓SPIRAL WOUND GASKET
SC 5000 SC 5100 SC 5200 SC 5300
TYPE
기본형Basic type
내륜형Inner ring type
SC-5000-NSC-5000-GSC-5000-PSC-5000-M
SC-5100-NSC-5100-GSC-5100-PSC-5100-M
Non-AsGraphitePTFEMica
Non-AsGraphitePTFEMica
제품번호 Number of product FILLER 특 징 Characteristic
기본형 가스켓은 MALE-FEMALE FACE FLANGE나 TONGUE
AND GLOOVE FACE FLANGE에 사용되고 VALVE의 BONNET,
COVER등에도사용됩니다.
Basic type of gasket is used for male-female face flange or tongueand groove face flange and also used for bonnet and cover ofvalve.
내륜형 가스켓은 MALE-FEMALE FACE FLANGE에 사용하며 내륜은
가스켓의 보강과 내압을 견딜 수 있게 하며 관내경과 가스켓 내경
사이의간격을없애유체가고이는것을방지합니다.
Inner ring type of gasket is used for male-female face flange.Inner ring helps for reinforcement of gasket as well as resistanceof internal pressure and also prevents from gathering of fluid byelimination of gap between the inside diameter of pipe andgasket.
외륜형Outer ring type
SC-5200-NSC-5200-GSC-5200-PSC-5200-M
Non-AsGraphitePTFEMica
외륜형 가스켓은 FLANGE의 BOLT에 내접하여 가스켓이 FLANGE
표면의 중심부분에 위치하도록 합니다. RING이 가스켓 보강역할을
합니다.
Outer ring type gasket helps gasket to be placed on the center offlange surface by touching internally with bolt of flange. Ringworks for reinforcement of gasket.
내외륜형Outer and
Inner ring type
SC-5300-NSC-5300-GSC-5300-PSC-5300-M
Non-AsGraphitePTFEMica
내륜형 가스켓과 외륜형 가스켓의 장점을 두루 가지고 있는 가스켓으로
내륜은 내압과 유체고임을 방지해 주고 외륜은 가스켓 보강역할을
합니다. 가장 많이사용되는 TYPE 입니다.
This is the gasket both merits of inner/outer ring gasket and innerring helps to prevent from internal pressure and gathering of fluid,while outer ring helps for reinforcement of gasket.
SC 5000~5300
스파이럴운드가스켓SPIRAL WOUND GASKET
28 │ http://www.scgasket.co.kr
사사용용가가능능 온온도도 USABLE TEMPERATURE
Filter 재질 Materials
Non-As
Graphite
PTFE
Mica
온도 Temperature
-200 ~ 400℃
-270 ~ 450℃
-260 ~ 300℃
압력 Pressure(Mpa)
30
30
20
Carbon Steel
SUS304 (L)
SUS316 (L)
SUS321
SUS347
티탄 (Titanium)
니켈 (Nickel)
SUS304 (L)
SUS316 (L)
SUS321
SUS347
티탄 (Titanium)
니켈 (Nickel)
KS, JIS 규격 : 10K, 16K, 20K, 30K, 40K, 63K..
JPI & ANSI : 150LB, 300LB, 400LB, 600LB, 900LB..
DIN : 10bar, 20bar, 30bar, 40bar..
※ 규격외사이즈도제작가능합니다.
SC5000 ~5300
사사용용 후후렌렌지지 규규격격 SPECIFICATIONS OF FLANGE IN USE
RRIINNGG 구구성성재재료료 COMPOSITION OF MATERIALS HHOOOOPP 구구성성재재료료 COMPOSITION OF MATERIALS
메탈자켓가스켓METAL JACKET GASKET
sung chang co.,ltd.│ 29
메탈자켓 가스켓은 내부충진제의 외부를 얇은 금속박판으로
피복한메탈가스켓입니다.
여러가지 형상으로 제작이 가능하여 이형 플랜지나 열교환기용
가스켓으로많이사용됩니다.
평형과파형두가지가생산됩니다.
Metal jacket gasket is a metal gasket, which the exteriorof inner filler coated with metal thin plate. Possible to befabricated in various shapes and generally used fordifferent types of flange and gasket for heat exchanger.Produced in two types of plain and corrugation.
NOTE 1 Heat Exchanger shapes
파 형 Corrugation type 평형 Plain type
충진제
SC-5401
충진제
SC-5400
TYPE
평형 Corrugation type
파형 Plain type
제품번호 Number of product
SC-5400
SC-5401
충진제 Filler
Non-As
Graphite
PTFE
Ceramic
Glass
금속박판 Metal thin plate
Carbon Steel
SUS304 (L)
SUS316 (L)
SUS321
SUS347
티타늄 (Titanium)
모넬 (Monel metal)
5Cr-0.5Mo
SC 5400, 5401Characteristic
30 │ http://www.scgasket.co.kr
용용 도도
단일 금속판을 평형 또는 톱니형으로 가공하여 씰성과 사용
압력을 높인 제품이다. 씰성을 높이기 위해 그라파이트
테이프를양면접착한제품도있습니다.
The product processed single metal plate in the shape ofplain type or serrated typefor improved sealing property and pressure for the use.Also available the product adhered graphite tape on bothsides for improved sealing property.
고온, 고압의증기라인, 열교환기밸브본넷트등에사용된다.
Used for steam line of high temperature, high pressure,valve bonnet of heat exchanger, etc.
사사용용가가능능 온온도도 USABLE TEMPERATURE
금속재질 Metal Materials
Steel
SUS304
SUS316
SUS321
SUS347
티탄 (Titan)
온도 Temperature
530℃
420℃
800℃
800℃
800℃
1,050℃
압력 Pressure(Mpa)
14
SC 5500
톱니형·평형가스켓SERRATED·FLAT METAL GASKET
Characteristic
sung chang co.,ltd.│ 31
용용도도
Characteristic
단일 금속의 단면을 오발, 옥타고날등으로 가공한 RING
형태의 제품으로 고온 고압의 유체를 취급하는 링조인트용
플랜지에사용되는가스켓이다.
Gasket used for flange of ring joint treating fluid of hightemperature/pressure as the product in shape of ringprocessed section of single metal in oval, octagonal, etc.
화학플렌트, 선박, 석유정제등의고온, 고압의증기,
가스라인등에사용
* 링조인트용플렌지에만사용
Applicable for steam and gas line of high temperature/pressure for chemical plants, vessels and refining oil.* Used for flange of ring joint only
Name Cross section
API type R ovalring-joint
API type R octagonal ring-joint
API type RX pressureenergized ring-joint
API type BX pressure energized
ring-joint
Modified bridgeman ring-joint
Delta ring-joint
Lens ring-joint
Double cone ring-joint
Round ring-joint
Weld-ring
SC 6500
링조인트메탈가스켓RING JOINT METAL GASKET
32 │ http://www.scgasket.co.kr
기술자료GASKET TECHINICAL DATA
1. 재질의선정 (Selection of Optimum Sheet)
사용조건(내부유체의온도, 부식성, TEST 압력과사용압력, 플렌지의형상, 가스키트의폭)에 적합한재질을선정한다.
Considering working conditions(temperature, corrosiveness, test & working pressure, flange type, gasket width),optimum gasket material should be selected.
2. 가스키트장착시의주의사항 (Precautions in Mounting)
•플렌지면의조도는 25S 이상으로한다.
•The roughness of flange surfaces should be above 25S.•플렌지면에이물질이부착되어있거나플렌지면이훼손되어서는안된다.
•Flange surfaces should be neither contaminated nor damaged.•플렌지면에비틀림이없어야하며평행하고중심이틀어지지않아야한다.
•Flange surfaces should be parallel without deformation and the center should not be deformed.•가스키트는플렌지면을깨끗이한후에정확한위치에장착시켜야한다.
•Keep flange surfaces clean and then mount the gaskets in correct position.•Bolting은 아래와같이순서적으로실시해야한다.
•Tighten the flange bolts in order illusted below.
•소부방지및GAS 누설방지목적으로가스키트에페이스트를도포할때는가능한얇고, 고르게도포를한다.
•When spreading gasket paste for the applications of anti-stick or gas leakage protection, the paste should bespread thinly and uniformly.•운전하기전반드시재조임을실시한다.
•Be sure to retighten the flange bolts before operation.•방직형시트를사용할때에는젖은손으로시트를만지거나소금기가있는물에시트가닿지않도록해야한다.
•When handling fabric sheets, do not bring them in contact with sea water or touch them with sweaty hands.
3. 보관 (Storage)
•직사광선과산소, 오존 등이닿지않고습기와먼지가없는서늘한장소에보관한다.
•Avoid exposing the gasket sheets to direct sunlight, oxygen, or ozone : store them in a cool, dark and clean place.•보관시에는 시트를 접거나 매달거나 말지를 말고 평행하게 가로로 적재한다. 부득이 말은 제품은 세우지 말고 눕혀서
보관하며권취경은가능한한크게한다.
•Store gasket sheets on a level base in a flat condition without folding, hanging or rolling. If necessary, roll upgasket sheets in diameter as large as possible and place them horizontally without standing vertically.•일부분을사용하고, 남은 제품은폴리에틸렌으로만든포장지에넣어밀봉한다.
•Put the remained gasket sheets in PE packing paper and store them.•선입선출 : 새로들어준것은아랫쪽에적재를하고, 오래된것은위쪽에적재를하여오래된것을먼저사용토록한다.
•First-in & First-out : Pile up old sheets on new sheets and ship out old sheets in advance.
조인트시트사용상의주의사항 (Guide for using gaskets)
sung chang co.,ltd.│ 33
기술자료GASKET TECHINICAL DATA
Shape of Gasket Sheet시트면의모양
가스켓시트의기본나비 b. (Standard Width)
A B
1a
1b
1c
W ≦ N
W ≦ N
1d
2
3
4(、)
5(、)
6
W ≦
W+T
8
W+N
4
N
2
W ≦N
2
:다만 을최대로한다.
W+T
8
W+N
4:but Max.
W+T
2
W+N
4:다만 을최대로한다.
W+T
2
W+N
4:but Max.
W+N
4
W+3N
4
N
2
N
2
N
4
3N
2
3N
8
7N
16
N
4
W
8
3N
8
※ 비고 : 이 표에서의가스켓시트기본나비 b.에 대한 A 및 B의 구분은옆면을참조할것.
주(‘)톱니의깊이 0.4mm, 이의 피치가 0.8mm를초과하지않을경우에는 1b 또는 1d를 사용한다.
※Note : For “A” and “B” of standard width, please refer to the table in the following page.Upto the depth 0.4mm and the pitch 0.8mm of saw-teeth, please refer to 1b or 1d.
34 │ http://www.scgasket.co.kr
기술자료GASKET TECHINICAL DATA
Self-Energizing typesO Rings, Metallic, Elastomer other gasket type considered as self-sealing
Gasket material Gasket factor mMin. design seating stress y(kgf/mm2)
(N/mm2)Sketches Use facing sketch
Elastomers without faboric or non-asbestos
Elastomers with faboric insertion
Elastomers with asbestos 3 pliesfiber 2 plies(wire-reinforced or not) 1 plies
Spiral-wound metal, with asbestos filler
Vegetable fiber
Corrugated meatal, doublejacketed with asbestos filler
Corrugated meatal
Flat metal jacketed wothasbestos filler
Grooved metal
Solid flat metal
Ring joint
Below 75 Shore Durometer 75 or higher Below Durometr
Carbon
Stainless or Monel
Soft aluminum
Soft copper or brass
Iron or soft steel
Monel or 4~6% chrome
Stainless steels
Soft aluminum
Soft copper or brass
Iron or soft steel
Monel or 4~6% chrome
Stainless steels
Soft aluminum
Soft copper or brass
Iron or soft steel
Monel
4~6% chrome
Stainless steels
Soft aluminum
Soft copper or brass
Iron or soft steel
Monel or 4~6% chrome
Stainless steels
Soft aluminum
Soft copper or brass
Iron or soft steel
Monel or 4~6% chrome
Stainless steels
Iron or soft steel
Monel or 4~6% chrome
Stainless steels
0
0
0.14 ( 1.37)
0.28 ( 2.75)
1.55 ( 15.20)
2.04 ( 20.01)
2.60 ( 25.50)
0.77 ( 7.55)
7.03 ( 68.89)
2.04 ( 20.01)
2.60 ( 25.50)
3.16 ( 30.99)
3.87 ( 37.95)
4.57 ( 44.82)
2.60 ( 25.50)
3.16 ( 30.99)
3.87 ( 37.95)
4.57 ( 52.37)
5.34 ( 52.37)
3.87 ( 37.95)
4.57 ( 44.82)
5.34 ( 52.37)
5.62 ( 55.11)
6.33 ( 62.08)
6.33 ( 62.08)
3.87 ( 37.95)
4.57 ( 44.82)
5.34 ( 52.37)
6.33 ( 62.08)
7.10 ( 69.63)
6.19 ( 60.70)
9.14 ( 89.63)
12.66 (124.16)
15.33 (150.34)
18.28 (179.27)
12.66 (124.16)
15.33 (150.34)
18.28 (179.27)
0
0.50
1.00
1.25
2.25
2.50
2.75
1.75
2.50
3.00
2.50
2.75
3.00
3.25
3.50
2.50
3.00
3.25
3.50
3.75
3.25
3.50
3.75
3.50
3.75
3.75
3.25
3.50
3.75
3.75
4.25
4.00
4.75
5.50
6.00
6.50
5.50
6.00
6.50
-- -
B
A
0.50
1.00
1.25
2.25
2.50
2.75
1.75
2.50
3.00
2.50
2.75
3.00
3.25
3.50
2.50
3.00
3.25
3.50
3.753
3.25
3.50
3.75
3.50
3.75
3.75
3.25
3.50
3.75
3.75
4.25
4.00
4.75
5.50
6.00
6.50
5.50
6.00
6.50
※ 비고 : 1. 가스켓계수 m은가스켓이전부볼트구멍의안쪽가장자리보다안쪽에만있는것에적용한다.
2. 이 표에는일반적으로많이사용되는가스켓의재료및접촉면을가스켓시이트의유효나비 b를
사용하였을때, 실제로사용해서만족한다는것이일반적으로명백한m과 y의 설계값을표시한것이다.
3. *의 표시가가스켓에서겹침이있는표면은 1c, 1d, 2등의 시이트면의형상의노빙(돌출한접촉면)에 향하게
해서는안된다.
※Note : 1. Gasket factor(m) is applivable only in case that the gasket is wholly placed inside the In-dia of bolt holes.
2. This table gives a list of many commonly used gasket materials and contact facings with suggested design values of m and y that have generally proved satisfactory in actual service when using effective gasket seating with b.
3. In *marked gaskets, the surface of a gasket having a lap should be against the smooth surface of the facing and not against the nubbing of 1c, 1d & s.
sung chang co.,ltd.│ 35
36 │ http://www.scgasket.co.kr
SC 1000
윤활유입테프론함침면섬유팩킹COTTON FIBER IMPREGNATED WITH PTFE BRAIDED PACKING
양질의 면사를 팔편 도는 격자편으로 편조하여 제조한 팩킹
으로 특수윤활재와 고순도의 PTFE액이 함침되어져
SLEEVE의 손상을우려해야하는펌프또는선박용에탁월한
기능을보유한팩킹이다.
A packing made of braided high quality cotton thread ineight braids or grid braid and the one of very superiorfunction for pumps or vessels being concerned aboutdamage of sleeve as impregnated with special lubricantand high purity of PTFE solution.
Pressure
Temperature
Linear speed
Ph range
PUMP
2
-50 ~ 120
2 ~ 8
4 ~ 12
MIXER
4
VALVE
10Mpa
℃
m/s
폴리아크릴로니트릴 필라멘트에 PTFE를 함침시켜 만듦으로
해서팩킹의강도를높인제품으로, 마모와충격에대한저항을
가지며, 경제성이 뛰어나 기존의 석면제품의 대체품으로
사용되는팩킹이다. 일반적인펌프나밸브에사용된다.
(※고속회전체에는부적합합니다.)
The product made by PTFE impregnated intopolyacrylonitrile filament to improve strength of packingand due to resistance against abrasion and shock as wellas highly economic feasibility, used as replacementpacking for existing products of asbestos. Applicable forpumps and valves of high temperature/pressure. (※Not suitable for body of high speed revolution)
Pressure
Temperature
Linear speed
Ph range
PUMP
5
-100 ~ 200
0 ~ 12
2 ~ 12
MIXER
10
VALVE
20Mpa
℃
m/s
SC 1100
윤활유입테프론함침아크릴섬유팩킹ACRYLIC FIBER IMPREGNATED WITH PTFE BRAIDED PACKING
Characteristic
Characteristic
sung chang co.,ltd.│ 37
테프론섬유편조팩킹PURE PTFE BRAIDED PACKING
SC 1200P.T.F.E 섬유를 8편 또는 격자편으로 편조한 팩킹으로 내약
품성 및 내식성이 극히 우수하여 팩킹에 의한 유체의 오염을
방지하는 용도에 적합한 팩킹으로 거의 모든산, 알칼리용제,
회전기기, 왕복운동기기, 밸브등에사용된다.
Packing braided PTFE fiber in eight braids or grid braid,which has very excellent chemical resistance andcorrosion resistance and suitable for prevention fromcontamination of fluid by packing being used for almost allof acid and alkali solvents, revolution instruments,reciprocating instruments, valves, etc.
Pressure
Temperature
Linear speed
Ph range
PUMP
5
-200 ~ 280
0 ~ 8
0 ~ 14
MIXER
15
VALVE
20Mpa
℃
m/s
Characteristic
테프론섬유팩킹(SC 1200)에 특수윤활제를 함침시킨 팩킹으로
내식성이 가장 우수한 팩킹이다. 거의 모든 약품에 사용
가능하며, 기계적 강도가 강하며, 내마모성도 우수하다. 부식성
유체, 염산 초산 및 각종 화학약품, 펌프, 왕복운동기기, 회전
기기등에사용된다.
Packing impregnated special lubricant into Teflon fiberpacking (SC 1200), which has the best corrosionresistance. Applicable for almost all of chemicals andstrong mechanical strength as well as excellent abrasionresistance. Usable for corrosive fluids, various chemicalssuch as hydrochloric acid and nitrile acid, pumps,reciprocating instruments, revolution instruments, etc.
Pressure
Temperature
Linear speed
Ph range
PUMP
2
-100 ~ 250
0 ~ 12
2 ~ 12
MIXER
10
VALVE
15Mpa
℃
m/s
SC 1200L
윤활유입테프론섬유편조팩킹PTFE WITH LUBRICATE DIPPED BRAIDED PACKING
Characteristic
38 │ http://www.scgasket.co.kr
SC 1300
흑연입테프론섬유팩킹PTFE GRAPHITE BRAIDED PACKING
P.T.F.E에 흑연과 윤활유를 가공에 의해 일체화한 섬유사를
단면각형으로견고하게편조한코일팩킹이다.
자체윤활성과 내구성, 열전도성이 우수하여 석유화학, 케미칼,
동력산업에유용하게쓰인다.
Coil packing braided fiber yarn, which was integratedgraphite and lubricant into PTFE by processing, solidly insquare shape of section and GFO is a registeredtrademark of Gore-tex.Valuably used for petrochemistry, chemical and powerindustry due to excellent own lubricative property anddurability as well as thermal conductivity.
Pressure
Temperature
Linear speed
Ph range
PUMP
3
-200 ~ 280
0 ~ 20
0 ~ 14
MIXER
10
VALVE
20Mpa
℃
m/s
탄화섬유사를 P.T.F.E 디스퍼젼과 윤활유를함침시킨뒤 단면
각형으로 편조한 코일팩킹으로, 펌프용으로 사용시 내열,
내약품성이 우수하며, 자기윤활성이 뛰어나 마찰열에 의한
팩킹의 손상이 적어 수명이 연장된다. 산, 알칼리용액, 해수,
공업용폐수등에사용된다.
Coil packing braided carbide fiber in square shape ofsection after PTFE dispersion and lubricant impregnated,which has excellent thermal/chemical resistance when itused for pump and life can be extended because of lessdamage to packing by frictional heat as it has excellentown lubricative property. Applicable for acid, alkalisolution, sea water and industrial waste water.
Pressure
Temperature
Linear speed
Ph range
PUMP
2.5
-50 ~ 260
0 ~ 15
1 ~ 13
MIXER
15
VALVE
15Mpa
℃
m/s
SC 1400
윤활유입테프론함침탄화섬유팩킹CARBONIZED FIBER IMPREGNATED WITH PTFE BRAIDED PACKING
Characteristic
Characteristic
sung chang co.,ltd.│ 39
윤활유입테프론함침탄소섬유팩킹CARBON FIBER IMPREGNATED WITH PTFE BRAIDED PACKING
SC 1500탄소섬유를 P.T.F.E 분산액과 함침하여 격자편으로조밀하게
직조한 팩킹으로 내열성과 내약품성이 우수하며, 마찰열의
방산이 용이하고 수명이 길다. 부식성유체, 증기, 유기용제,
탄화수소, 각종유류, 회전기기, 밸브, 회전펌프, 교반기, 플랜지
등에사용된다.
Packing of carbon fiber impregnated PTFE dispersionand weaved densely in grid braid. Excellent thermal andchemical resistance, and easy for scattering of frictionalheat to be longer life. Applicable for corrosive fluids,organic solvents, hydrocarbon, various kinds of oil,revolution instruments, valves, revolution pumps, mixersand flanges, etc.
Pressure
Temperature
Linear speed
Ph range
PUMP
5
-200 ~ 600
0 ~ 25
0 ~ 14
MIXER
10
VALVE
25Mpa
℃
m/s
아라미드섬유사에 P.T.F.E를 함침시켜 직조한팩킹으로매우높은인장강도를 가짐으로 이송하는 유체내의 슬러지가많아팩킹의 조직이 쉽게 파괴되고 팩킹을 자주 교환해야 하는부위에 사용하면 극대의 효과를 낼 수 있는 팩킹이다. 물,해수, 공업폐수, 산 및 알칼리용액, 각종 유기용제 등에 사용된다.
Packing of aramid fiber yarn impregnated PTFEand weaved. Due to very high tension strength,possible to take the maximum effect when it usedfor areas of packing to be damaged easily due tomany sludges in transferring fluid and replacedfrequently. Applicable for water, seawater, industrialwaste water, acid and alkali solutions, various kindsof organic solvents, etc.
Pressure
Temperature
Linear speed
Ph range
PUMP
2.5
-50 ~ 260
0 ~ 15
1 ~ 13
MIXER
15
VALVE
15Mpa
℃
m/s
SC 1600
윤활유입테프론함침아라미드섬유팩킹ARAMID FIBER IMPREGNATED WITH PTFE BRAIDED PACKING
Characteristic
Characteristic
40 │ http://www.scgasket.co.kr
SC 1700
인코넬선입그라파이트섬유팩킹INCONEL WIRE-REINFORCED FLEXIBLE GRAPHITE BRAIDED PACKING
그라파이트얀섬유에 내열성이 우수한 인코넬선을 보강하여
조밀하게 편조한 팩킹으로 고온, 고압에서 안정된 성능을
유지함은 물론, 기존의 그라파이트 몰드 팩킹의 단점을 보완
하여신축성이뛰어나특히밸브팩킹용으로적합한제품입니다.
Packing of graphite yarn fiber reinforced by inconel wireof excellent thermal resistance and braided densely. Dueto stable performance under high temperature/pressureand also excellent flexibility supplemented demerits ofexisting graphite mold packing as well, suitable especiallyfor valve packing.
Pressure
Temperature
Linear speed
Ph range
PUMP
3
-250 ~ 650
0 ~ 8
0 ~ 14
MIXER
10
VALVE
30Mpa
℃
m/s
팽창흑연 얀을 P.T.F.E 필름으로 피복하여, 단면각형으로
편조한 코일팩킹입니다. 각 재질별 장점을 살린 그랜드팩킹
으로 주재료가 팽창흑연이어서 씰성, 내구성이 우수하고,
표면을 P.T.F.E로 피복하여 축저항이 매우 작아지는 특징을
가집니다.
Coil packing of expanded graphite yarn coated with PTFEfilm and braided in square shape of section.Gland packing made use of merits by each material andexcellent sealing property with durability due to mainmaterial of expanded graphite. Characteristics of axisresistance becoming very smaller as PTFE coated on thesurface.
Pressure
Temperature
Linear speed
Ph range
PUMP
3
-200 ~ 280
20
1 ~ 14
MIXER
-
VALVE
Mpa
℃
m/s
SC 1800
테프론함침그라파이트섬유팩킹GRAPHITE FIBER IMPREGNATED WITH PTFE BRAIDED PACKING
Characteristic
Characteristic
sung chang co.,ltd.│ 41
그라파이트섬유패킹FLEXIBLE GRAPHITE BRAIDED PACKING
SC 1900그라파이트얀섬유를 조밀하게 편조한 팩킹으로 금속선을
보강재로넣지않아고온회전기기에적합한제품입니다.
왕복운동기기에는다른아답터패킹과조합하여사용합니다.
Packing of graphite yarn fiber braided densely andsuitable for revolution instruments of high temperature asno metal wire inserted as reinforcing matter.For reciprocating instruments, used in combination withother adaptor packings.
Pressure
Temperature
Linear speed
Ph range
PUMP
3
-250 ~ 650
0 ~ 8
0 ~ 14
MIXER
10
VALVE
25Mpa
℃
m/s
탄력성이 좋은 특수고무를 내장재로 하여 내약품성이 좋은
섬유를편조한후 PTFE 섬유로감싼제품입니다.
내약품성이 우수하고 탄력성이 좋아 반복사용도 가능한
TANK LIP SEAL용 패킹으로적합합니다.
Product wrapped with PTFE fiber after braided fiber ofexcellent chemical resistance using special rubber ofexcellent elasticity as the interior.Suitable for packing of tank lip seal possible to userepeatedly due to excellent chemical resistance and goodelasticity.
사용온도 : 120℃
(Use Temperature : 120℃)
SC 2000
해치카바패킹HATCH COVER PACKING
Characteristic
Characteristic
42 │ http://www.scgasket.co.kr
기술자료GLAND PACKING TECHINICAL DATA
1. PACKING 길이 (Length of Packing)
2. PACKING 장착및조정 (Stuffing and Adjustment of Packing)
1) 교환시사용하던 PACKING 전량교환Remove all the old packing from the stuffing box.
2) BOX 내부를깨끗이청소한다.Clean the inside of the stuffing box.
3) 적당한 SEAL 조제를사용한다.Use proper seal compounds.
4) 축의 손상부분을수리한다.Repair the defective part of stem.
5) PACKING 재질및폭을확인Check material and width of packing.
6) 축경과동일한축을이용한필요한길이를절단하며조작순서는다음과같다.Cut the packing into proper length by using the stem with the stem dia.Working procedures are as below.
취급상의주의사항 (Handling Procedure)
sung chang co.,ltd.│ 43
기술자료GLAND PACKING TECHINICAL DATA
7) 최하부의 PACKING은 5~10% (최고 20~30%) 압축하여예압을가한다.For the lowest part of packing, add pre-pressure by 5~10% (Max. 20~30%) compression.
8) 체부압력은유체압력에대하여통상 1.2~1.5배로 한다.Maintain seating pressure 1.2~1.5 times as high as fluid pressure.
9) 충전이완료된후조금조여서 10~20분 방치한후다시풀어서강하게조여준다.After seating, tighten slightly and leave it 10~20 minutes. Unfasten and, then, tighten it strongly again.
10) 무부하운전을시켜발열, 누설 등을 CHECK한 후부하운전토록한다. 부하 운전시축은 1~2시간에정상온도가되도록하여야한다. 그 온도는실온보다 30~40℃가높아도정상으로판단된다.Check heat-generation and leakage during the operation under no loading.And operate with loading. For the load operation, the stem should reach normal temperature in 1~2 hours.The temperature higher than room temperature by 30~40℃ is regarded as normal.
11) 조임 후 PACKING 폭의 1/2 정도의간격을둔다. (1개 추가)After tightening, leave a space of 1/2 packing width. (add 1 more packing)
3. 운전시, 운전중주의사항 (Cautions during Operation)
1) 회전시축의진동은 0.07mm이하로한다.Stem vibration should be below 0.07mm when rotating.
2) 온도 상승이급격할때는조임하중을증가시킨다.Reduce the tightening load when it shows the very sharp increase of temperature.
3) 누설이증가시 BOLT 조임을추가로하여증채는최대 1회전으로하며통상 1/2~1/6회전으로조정한다.Add the bolt tightening when the leakage increases. Maximum bolt tightening should be adjusted by maximum one ratetion, but normally adjusted by 1/2~1/6 rotation.
4) 가동 중누설이없으면축의마찰열의방산이되지않으므로적절한누출량을확보한다.If there is no leakage during operation, maintain the proper leakage volume not to emit the friction heat of stem.
4. 보 관 (Storage)
1) PACKING이 변질되지않도록보관한다.즉, PACKING에는각종윤활유가포함되어있으므로직사광선, 산소, 오존, 고온다습에영향을받지않도록보관한다.Store the packing to be unchanged. Avoid direct rays, oxygen, ozone or high temperature humid surroundings because the packing includes various lubricans.
2) 먼지, 불순물등이물질이묻지않도록한다. (축의 손상요인이크다.)Reduce the tightening load when it shows the very sharp increase of temperature.
3) 해풍에주의해야한다.Avoid the sea wind.
44 │ http://www.scgasket.co.kr
기술자료GLAND PACKING TECHINICAL DATA
압력 (pressure) (㎏/㎠)
10이하 (Upto 10)
10 ~ 40
40 ~ 63
링패킹수 (Q’ty of Ring Packing)
5
6
7
압력 (pressure) (㎏/㎠)
63 ~ 105
105 ~ 175
175 ~ 315
링패킹수 (Q’ty of Ring Packing)
8
9
10
압력 (pressure) (㎏/㎠)
10이하 (Upto 10)
1 ~ 5
5 ~ 10
10 ~ 20
링패킹수 (Q’ty of Ring Packing)
4 ~ 5
5 ~ 7
6 ~ 8
7 ~ 9
1,800 RPM
3,600 RPM
7,200 RPM
10,000 RPM
회전수 (Rotary Speed)압력 (pressure) 10 ㎏/㎠
0.100
0.075
0.045
0.025
20 ㎏/㎠
0.063
0.050
0.033
0.025
100 ㎏/㎠
0.045
0.038
0.025
0.020
축경 (Stem Dia)
20이하 (Upto 10)
20 ~ 35
35 ~ 50
50 ~ 75
75 ~ 110
110 ~ 150
150 ~ 200
200 이상 (over 200)
압력 (pressure) (㎏/㎠)
5
6.5
10
13
16
19
22
25
( Unit : mm )
( Unit : mm )
축축((SSTTEEMM)) 흔흔들들림림의의 최최고고 허허용용차차 MAXIMUM TOLERANCE OF STEM WAVERING
SSTTEEMM과과 PPAACCKKIINNGG 폭폭과과의의 관관계계 RELATION BETWEEN STEM AND PACKING WIDTH
회회전전 펌펌프프의의 각각압압력력에에 대대한한 링링패패킹킹의의 수수 RING PACKING Q’TY ACCORDING TO ROTARY PUMP PRESSURE
밸밸브브의의 각각압압력력에에 대대한한 링링패패킹킹의의 수수 RING PACKING Q’TY ACCORDING TO VALVE PRESSURE
sung chang co.,ltd.│ 45
기술자료GLAND PACKING TECHINICAL DATA
극산(Maxi-mumAcid)
강산(Severe Acid)
약산(Mild Acid)
약알카리(Mild Alkali)
강알카리(Severe Alkali)
극알
카리(Max-imumAlkali)
중성(Neu-tral)
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14
마(Flax)
모 시(Ramie)
백석면(Asbestos Fiber)
PTFE + 백석면(PTFE + Asbestos Fiber)
납(Pb)
Al
Cu
납, 프라스틱(Pb, Plastic)
Al, 프라스틱(Al, Plastic)
Cu + 석면(Cu + Asbestos Fiber)
석면 + 프라스틱(Asbestos Fiber + Plastic)
PTFE섬유(PTFE Fiber)
탄소섬유(Carbon Fiber)
Cu + 프라스틱(Cu + Plastic)
면(Cotton)
Aramid + PTFE
GRAPHITE
재료별 (Material)
pH
재재료료별별 pHH 적적용용범범위위 ((FFSSAA)) PH RANGE OF PACKING MATERIAL
46 │ http://www.scgasket.co.kr
사고의분류 (Accidents)
원인의분류 (Causes)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
패킹과잉조임(Over-tightening of packing)
패킹선정부적합(Selection of Improper Packing)
냉각 불충분(Lack of Cooling)
씰링 물부족(Lack of Sealing Water)
설계불량(Design Error)
슬리브사상불량(Defective Forming of Sleeve)
패킹, 슬리브마모(Abrasion of Packing or Sleeve)
1+2+3
1+2+5
1+2+7
1+3
1+4
1+6
1+7
3+6
기타(Others)
(1)
패킹의누설(Leakageof
Packing)
패킹의눌어붙임(Stickinessof
Packing)
패킹부식(Corrosionof
Packing)
슬리브마모(Abrasionof
Sleeve)
패킹의수명짧음(Short Life ofPacking)
(1)+(2)(1)+(2)+(4)
(1)+(3) (1)+(4) (2)+(5) (4)+(6)
(2) (3) (4) (5) (6)
복합사고 (Complicated accidents)
(7) (8) (9) (10) (11)
O O O O O O
O
O
O
O
O
O O O O
O
O
O
O
O
O
O
O O O
기술자료GLAND PACKING TECHINICAL DATA
GGLLAANNDD PPAACCKKIINNGG의의사사고고 원원인인별별 분분류류 FAILURE CAUSES OF GLAND PACKINGS
200 1.0 20 200 4.9 5
300 25.9 300 24.5 5
260 10.3 260 2.0 20 260 9.8 5 260 9.8 5
260 1.6 16 260 4.9 5 260 4.9 5
260 5.1 260 1.6 20 260 4.9 5 260 4.9 5
150 1.0 10 150 4.9 1 150 4.9 5
200 10.3 200 9.8 1
260 10.3 260 2.0 16 260 14.7 5 260 14.7 5
600 2.5 25 600 14.7 5 600 14.7 5
650 43.1
350 10.3 300 1.0 8
sung chang co.,ltd.│ 47
현상 (Phenomena)
발열 발생(Heat Generation)
이상음발생(Noise)
누설량이많다(Over Leakage)
PACKING GLAND BUSH밖으로돌출
(Packing Extrusion from Gland bush)
원인 (Causes)
(1) Packing의 과잉체부 (Over-tightening of Packing)
(2) 냉각수부족 (Lake of Cooling Water)
(3) 유체압력이높다, 주속이낮다
(High Fluid Pressure, Low Shaft Speed)
(1) Grandbush가 축에접촉
(Grandbush’s Contact with Steam)
(2) Bearing의 마모 (Bearing Abrasion)
(3) Packing의 이완 (Packing Slackening)
(1) Packing 치수가작거나짧다 (Small Packing Size)
(2) 축의 마모 (Stem Abrasion)
(3) 축의 진동 (Stem Vibration)
(1) 축과 Bearing의 Clearance가 크다.
(Wide Clearance of Stem and Bearing)
(1) Packing의 과잉체부
(Over-tightening of Packing)
Bolt를 균등히이완시켜적절누설량을유지
(Relax bolt tightness regularly to maintain proper leakage)
냉각수를적정량유지 (Maintain proper cooling water)
적합한 Packing을 선정 (Select proper packing)
Grandbush의 편제를수정 (Adjust glandbush)
Bearing을 교환 (Replace with bearing)
발열에주의하면서 Bolt를 균일히조임한다.
(Tighten bolts regularly to avoid heat generation)
바른 Packing 치수의것으로교환, 보수 교환
(Replace, repair or change with correct packing)
축, Bearing 수정 교환
(Adjust and change stem or bearing)
적정한 Clearance 유지
(Maintain the proper clearance)
Bolt를 균일하게이완시키고경질의패킹을사용
(Relax bolt thightness regularly and use harder gland packing)
대책 (Troubleshooting)
비석면그랜드팩킹
탄소섬유계(Carbon fiber series)
분 류(Classification)
제품 번호(Number of
product)
PTFE 섬유계(PTFE fiber series)
특수섬유계(Special fiber series)
흑연계(Graphite series)
흑연계 (범용)(Graphite series (general purpose))
SC-1400
SC-1500
SC-1200
SC-1200L
SC-1300
SC-1000
SC-1100
SC-1600
SC-1700
SC-1800
SC-1900
용 도 (Use)
밸 브 (Valve) 회전펌프 (Revolution pump) 왕복운동기기(Reciprocating instruments) 회전기기(Revolution instruments)
온도(℃)Temperature
압력(Mpa)
Pressure
온도(℃)Temperature
압력(Mpa)
Pressure
속도(m/s)Speed
온도(℃)Temperature
압력(Mpa)
Pressure
속도(m/s)Speed
온도(℃)Temperature
압력(Mpa)
Pressure
속도(m/s)Speed
사용가능범위 (Range of possible use) 주요 용도 (Main use)
기술자료GLAND PACKING TECHINICAL DATA
GGLLAANNDD PPAACCKKIINNGG 열열람람표표 ((용용도도,, 성성능능 ((UUSSEE,, EEFFFFIICCIIEENNCCYY))))
GGLLAANNDD PPAACCKKIINNGG의의누누설설 대대책책 ((회회전전 PPUUMMPP용용)) TROUBLESHOOTING FOR THE LEAKAGE OF GLAND PACKING (ROTARY PUMPS)
48 │ http://www.scgasket.co.kr
기술자료GLAND PACKING TECHINICAL DATA
온도(℃) (Temperature)
압력(Mpa) (Pressure)
속도(m/s) (Speed)
허용PV치 (Mpa.m/s) (Allowed PV value)
PH
축으로의조임성 (Tightness towards shaft)
제 품 번호 (Number of product)
1000
150
1.0
5
4.9
0~14
우수
★
★
★
200
1.0
15
11.7
2~12
우수
★
★
★
260
1.6
16
12.3
0~14
우수
★
★
★
★
★
★
★
★
★
260
1.6
20
12.3
0~14
우수
★
★
★
★
★
★
★
★
★
260
2.0
16
14.7
2~13
가능
★
★
★
260
2.0
20
14.7
2~14
양호
★
★
★
600
2.5
25
24.5
0~14
우수
★
★
★
★
★
★
★
★
★
★
1400 1200L 1300 1600 1200 1700
해수, 오수 (Seawater, polluted water)
상수, 청량수 (Tap water, Clear water)
흙탕물 (Muddy water)
보일러급수 (Water supply to boiler)
저압증기 (Steam of low pressure)
원유, 증유 (Crude oil, Heavy oil)
열매유 (Seed oil)
동·식물유 (Animal oil, Vegetable oil)
광물류 (Minerals)
알콜용제 (Alcohol solvent)
방향족 (Aromatic)
탄화수소 (Esther)
에스텔류 (Seawater, polluted water)
약산 (Weak acid)
약알카리 (Weak alkali)
강알칼리 (Strong alkali)
산화성산 (Oxidizing Acid)
산화제 (Oxidizer)
산화성산 (Oxidizing Acid)
이외의산 (Other acids)
펄프액 (Pulp liquid)
저온액 (Low temperature liquid)
화유체 (Fluid)
냉매 (Refrigerant)
수계유체
유계유체
용
제
부식성유체
기
타
★추천제품 (Recommended products)
GGLLAANNDD PPAACCKKIINNGG 선선정정표표 ((회회전전펌펌프프축축용용 FFOORR SSHHAAFFTT OOFF RREEVVOOLLUUTTIIOONN PPUUMMPP))
sung chang co.,ltd.│ 49
기술자료GLAND PACKING TECHINICAL DATA
온도한계(℃) (Temperature limit)
압력한계(Mpa) (Pressure limit)
속도한계(m/s) (Speed limit)
PH
축으로의조임성 (Tightness towards shaft)
제 품 번호 (Number of product)
1000 1100 1200L 1300 1200 1600 1700 1500
150
4.9
5
0~14
우수
★
★
★
★
★
★
★
200
9.8
1
2~12
우수
★
★
★
★
★
★
★
260
4.9
5
0~14
우수
★
★
★
★
★
★
260
4.9
5
0~14
우수
★
★
★
★
★
★
260
9.8
5
2~13
양호
★
★
★
★
★
★
★
★
★
★
260
9.8
5
2~13
가능
★
★
★
★
★
★
★
★
600
14.7
5
0~14
우수
★
★
★
★
★
★
★
★
★
★
★
★
★
300
24.5
5
0~14
양호
★
★
★
★
★
★
★
★
청수, 해수 (Clear water, Seawater)
오수, 흙탕물 (Polluted water, Muddy water)
보일러수, 가열수, 저압증기(Boiler water, Hot water, Steam of low pressure)
원유, 중유 (Crude oil, Heavy oil)
열매유 (Seed oil)
광물유, 동식물유(Mineral oil, Animal/Vegetable oil)
분체 (Pulverulent body)
폴리머 (Polymer)
슬러리액 (Slurry)
가스, 공기 (Gas, Air)
용제페이퍼류 (Solvent papers)
플랜지펌프 (Flange pump)
스토브로어
신축이음매 (Flexible joint)
교반기 (Mixer)
드라이어 (Dryer)
스크류피더 (Screw feeder)
기어펌프등 (Gear pump, etc.)
용
도
왕복운동
구
분
회전운동
수계유체
유계유체
유계유체
가스체
★추천제품 (Recommended products)
GGLLAANNDD PPAACCKKIINNGG 선선정정표표 ((기기기기용용 FFOORR IINNSSTTRRUUMMEENNTTSS))
50 │ http://www.scgasket.co.kr
sung chang co.,ltd.│ 51
KS B 1519
JIS B 2202
● 링가스키트(Ring Gasket) R F Type
전면자리플랜지용For flat face flange
대평면자리플랜지용For raised(large) face flange
소평면자리플랜지용For raised(small) face flange
10 A
15 A
20 A
25 A
32 A
40 A
50 A
65 A
80 A
90 A
100 A
125 A
150 A
175 A
200 A
225 A
250 A
300 A
350 A
400 A
450 A
500 A
550 A
600 A
650 A
700 A
750 A
800 A
850 A
900 A
1000 A
1100 A
1200 A
1300 A
1350 A
1400 A
1500 A
NPS
(호칭경)
GASKET I.D
(내경)
GASKET O.D (외경)
5K 10K 16K 20K 30K 40K 63K
1/4
1/2
3/4
1
1-1/4
1-1/2
2
2-1/2
3
3-1/2
4
5
6
7
8
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
40
44
48
52
54
56
60
18
22
28
35
43
49
61
77
90
102
115
141
167
192
218
244
270
321
359
410
460
513
564
615
667
718
770
820
872
923
1025
1130
1230
1335
1385
1435
1540
45
50
55
65
78
83
93
118
129
139
149
184
214
240
260
285
325
370
413
473
533
583
641
691
746
796
850
900
950
1000
1100
1210
1320
1475
1630
53
58
63
74
84
89
104
124
134
144
159
190
220
245
270
290
333
378
423
486
541
596
650
700
750
810
870
920
970
1020
1124
1234
1344
1498
1658
53
58
63
74
84
89
104
124
140
150
165
203
238
-
283
-
356
406
450
510
575
630
684
734
784
836
896
945
995
1045
1158
1258
1368
1474
1534
1584
1694
53
58
63
74
84
89
104
124
140
150
165
203
238
-
283
-
356
406
450
510
575
630
684
734
805
855
918
978
1038
1088
-
-
-
-
-
-
-
59
64
69
79
89
100
114
140
150
163
173
208
251
-
296
-
360
420
465
524
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
59
64
69
79
89
100
114
140
150
163
183
226
265
-
315
-
380
434
479
534
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
64
69
75
80
90
108
125
153
163
181
196
235
275
-
330
-
394
449
488
548
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
( 단위 : mm )
KS.JIS 관 FLANGE용GASKET치수(Gasket Dimensions for KS or JIS Flanges)
52 │ http://www.scgasket.co.kr
끼움형플랜지용For male and female flange
홈형 플랜지용For tongue and groove flange
10
15
20
25
32
40
50
65
80
90
100
125
150
175
200
225
250
300
350
400
450
500
550
600
650
700
750
800
850
900
1000
1100
1200
1300
1350
1400
1500
17.3
21.7
27.2
34.0
42.7
48.6
60.5
76.3
89.1
101.6
114.3
139.8
165.2
190.7
216.3
241.8
267.4
318.5
355.6
406.4
457.2
508.0
558.8
609.6
660.4
711.2
762.0
812.8
863.6
914.4
1016.0
1177.6
1219.2
1320.8
1371.6
1422.4
1524.0
18
22
28
35
43
49
61
77
90
102
115
141
167
-
218
-
270
321
359
410
460
513
564
615
667
718
770
820
872
923
1025
1130
1230
1335
1385
1435
1540
38
42
50
60
70
75
90
110
120
130
145
175
215
-
260
-
325
375
415
475
523
575
625
675
727
777
832
882
934
987
1092
1192
1292
1392
1442
1492
1592
28
32
38
45
55
60
70
90
100
110
125
150
190
-
230
-
295
340
380
440
483
535
585
635
682
732
787
837
889
937
1042
1142
1237
1337
1387
1437
1537
38
42
50
60
70
75
90
110
120
130
145
175
215
-
260
-
325
375
415
475
523
575
625
675
727
777
832
882
934
987
1092
1192
1292
1392
1442
1492
1592
NPS
(호칭경)
강관외경
(Steel Pipe OD) d₁
끼움형플랜지용 (Male and female flange) 홈형 플랜지용 (Tongue and groove flange)
가스킷내경 (Gasket ID) d₂가스킷외경 (Gasket OD) d₂가스킷내경 (Gasket ID) d₂가스킷외경 (Gasket OD) d₂
( 단위 : mm )
KS.JIS 관 FLANGE용GASKET치수(Gasket Dimensions for KS or JIS Flanges)
sung chang co.,ltd.│ 53
●링가스켓(Ring Gasket) R F Type
ASME B 16.21 (1992)에 의한 ASME/ANSI B 16.5 관 Flange용 및 ASME B 16.47 Series ‘B’Flat Ring(R·F) Type Soft Gasket 치수(API 605)
1/2
3/4
1
1-1/4
1-1/2
2
2-1/2
3
3-1/2
4
5
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
15 A
20 A
25 A
32 A
40 A
50 A
65 A
80 A
90 A
100 A
125 A
150 A
200 A
250 A
300 A
350 A
400 A
450 A
500 A
550 A
600 A
650 A
700 A
750 A
800 A
850 A
900 A
950 A
1000 A
1050 A
1100 A
1150 A
1200 A
1250 A
1300 A
1350 A
1400 A
1450 A
1500 A
21.3
26.9
33.3
42.2
48.5
60.5
73.2
88.9
101.6
114.3
141.2
168.1
218.9
273.1
323.9
355.6
406.4
457.2
508.0
558.8
609.6
660.4
711.2
762.0
812.8
863.6
914.4
965.2
1016.0
1066.8
1117.6
1168.4
1219.2
1270.0
1320.8
1371.6
1422.4
1473.2
1524.0
47.8
57.2
66.5
76.2
85.9
104.6
124.0
136.7
162.1
174.8
196.9
222.3
279.4
339.9
409.7
450.9
514.4
547.0
606.6
660.4
717.6
725.4
776.2
827.0
881.1
935.0
987.6
1044.4
1095.2
1146.0
1196.8
1255.8
1306.0
1357.4
1408.2
1463.5
1514.3
1579.6
1630.4
53.8
66.5
73.2
82.6
95.3
111.3
130.0
149.4
165.1
180.8
215.9
251.0
307.8
362.0
422.1
485.6
539.8
596.9
654.1
704.9
774.7
771.7
825.5
886.0
939.8
993.6
1047.8
1098.6
1149.4
1200.2
1251.0
1317.8
1368.6
1419.4
1470.2
1555.8
1593.9
1655.8
1704.8
53.8
66.5
73.2
82.6
95.3
111.3
130.0
149.4
162.1
177.8
212.9
247.7
304.8
358.6
419.1
482.6
536.4
539.9
647.7
701.8
768.4
746.3
800.1
857.3
911.4
962.2
1022.4
-
-
-
-
-
-
-
-
-
-
-
-
53.8
66.5
73.2
82.6
95.3
111.3
130.0
149.4
162.1
193.5
241.3
266.7
320.5
400.1
457.2
492.3
565.2
612.6
682.8
733.6
790.4
765.0
819.2
879.3
933.5
997.0
1047.8
-
-
-
-
-
-
-
-
-
-
-
-
63.5
69.9
79.2
88.9
98.6
142.7
165.1
168.1
-
206.2
247.7
289.1
358.6
434.8
498.3
520.7
574.5
638.0
698.5
838.2
838.2
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
NPS
(호칭경)
GASKET I.D
(내경)
GASKET O.D (외경)
CLASS 150 CLASS 300 CLASS 400 CLASS 600 CLASS 900
( 단위 : mm )
ANSI ASME 관 FLANGE용GASKET 치수표
54 │ http://www.scgasket.co.kr
●링가스켓(Ring Gasket) R F Type
10
15
20
25
32
40
50
65
80
100
125
150
200
250
300
350
400
450
500
600
700
800
900
1000
1200
1400
1600
1800
2000
2200
2400
2600
2800
3000
3200
3400
3600
18
22
27
34
43
49
61
77
89
115
141
169
220
273
324
356
407
458
508
610
712
813
915
1016
1220
1420
1620
1820
2020
2220
2420
2620
2820
3020
3220
3420
3620
39
44
54
64
76
86
96
116
132
152
182
207
262
317
373
423
473
528
578
679
784
890
990
1090
1307
1524
1724
1931
2138
2348
2558
2762
2972
3172
3382
3592
3805
46
51
61
71
82
92
107
127
142
162
192
218
273
328
378
438
489
539
594
695
810
917
1017
1124
1341
1548
1772
1972
2182
2385
2595
2795
3015
3230
-
-
-
46
51
61
71
82
92
107
127
142
162
192
218
273
329
384
444
495
555
617
734
804
911
1011
1128
1342
1542
1765
1965
2170
-
-
-
-
-
-
-
-
46.5
56.0
65.5
75.0
84.5
102.5
121.5
134.5
172.5
196.0
221.5
278.5
338.0
408.0
449.0
513.0
548.0
605.0
716.5
830.0
939.0
1047.0
1161.0
1383.0
1606.0
-
-
-
-
-
-
-
-
-
-
-
46
51
61
71
82
92
107
127
142
168
194
224
284
340
400
457
514
564
624
731
833
942
1042
1154
1365
1580
1800
2002
2232
-
-
-
-
-
-
-
-
46
51
61
71
82
92
107
127
142
168
194
224
290
352
417
474
546
571
682
747
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
NPS
(호칭경)
GASKET I.D
(내경) PN 6 PN 10 PN 16 PN 20 PN 25 PN 40
GASKET O.D (외경)
( 단위 : mm )
KS B ISO 7438 : DIN(BAR) 관 FLANGE용GASKET 치수표
sung chang co.,ltd.│ 55
KS B 1519
JIS B 2202
참고 : 관플랜지의가스키트치수
다음에표시하는사항은참고로표시하는것이며, 규격의일부는아니다.
1. 가스키트는원칙으로비금속가스키트로한다.
2. 이 가스키트는주로시-트가스키팅에서잘라낸것으로한다.
Note : Gasket Dimensions for Pipe FlangesBelow are for reference only, no specification1. Below are based on non-metallic gasket.2. This is cut from gasket sheet.
●전면가스키트(Full face Gasket) F F Type
10
15
20
25
32
40
50
65
80
90
100
125
150
175
200
225
250
300
350
400
450
500
550
600
650
700
750
800
850
900
1,000
1,100
1,200
1,350
1,500
18
22
28
35
43
49
61
77
90
102
115
141
167
192
218
244
270
321
359
410
460
513
564
615
667
718
770
820
782
923
1,025
1,130
1,230
1,385
1,540
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
605
655
720
770
825
875
945
995
1,045
1,095
1,195
1,305
1,420
1,575
1,730
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
555
605
665
715
770
820
880
930
980
1,030
1,130
1,240
1,350
1,505
1,660
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
23
23
25
25
25
25
27
27
27
27
27
27
27
27
27
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
16
20
20
20
24
24
24
24
24
24
28
28
32
32
36
75
80
85
95
115
120
130
155
180
190
200
235
265
300
320
345
385
430
480
540
605
655
720
770
825
875
945
995
1,045
1,095
1,195
1,305
1,420
1,575
1,730
55
60
65
75
90
95
105
130
145
155
165
200
230
260
280
305
345
390
435
495
555
605
665
715
770
820
880
930
980
1,030
1,130
1,240
1,350
1,505
1,660
12
12
12
12
15
15
15
15
19
19
19
19
19
23
23
23
23
23
25
25
25
25
27
27
27
27
33
33
33
33
33
33
33
33
33
4
4
4
4
4
4
4
4
4
4
8
8
8
8
8
12
12
12
12
16
16
20
20
20
24
24
24
24
24
24
28
28
32
32
36
호칭치수
Nominal
Size
가스키트내경
Gasket ID
d₂
가스키트외경
Gasket OD
D
보울트구멍의중심의경
Bolt hole Circle DiameterC
보울트구멍의경Bolt holeDiameterh
보울트구멍의수No. ofBolt hole
가스키트외경
Gasket OD
D
보울트구멍의중심의경
Bolt hole Circle DiameterC
보울트구멍의경Bolt holeDiameterh
보울트구멍의수No. ofBolt hole
호칭압력 2㎏/㎠플랜지용
(Nominal Pressure 2㎏/㎠Flange)
호칭압력 5㎏/㎠플랜지용
(Nominal Pressure 5㎏/㎠Flange)
KS.JIS 관 FLANGE용GASKET 치수(Gasket Dimensions for KS or JIS Flanges)
56 │ http://www.scgasket.co.kr
KS B 1519
JIS B 2202
참고 : 관플랜지의가스키트치수
다음에표시하는사항은참고로표시하는것이며, 규격의일부는아니다.
1. 가스키트는원칙으로비금속가스키트로한다.
2. 이 가스키트는주로시-트가스키팅에서잘라낸것으로한다.
Note : Gasket Dimensions for Pipe FlangesBelow are for reference only, no specification1. Below are based on non-metallic gasket.2. This is cut from gasket sheet.
●전면가스키트(Full face Gasket) F F Type
10
15
20
25
32
40
50
65
80
90
100
125
150
175
200
225
250
300
350
400
450
500
550
600
650
700
750
800
850
900
1,000
1,100
1,200
1,350
1,500
18
22
28
35
43
49
61
77
90
102
115
141
167
192
218
244
270
321
359
410
460
513
564
615
667
718
770
820
782
923
1,025
1,130
1,230
1,385
1,540
90
95
100
125
135
140
155
175
185
195
210
250
280
305
330
350
400
445
490
560
620
675
745
795
845
905
970
1020
1070
1120
1235
1345
1465
1630
1795
65
70
75
90
100
105
120
140
150
160
175
210
240
265
290
310
355
400
445
510
565
620
680
730
780
840
900
950
1000
1050
1160
1270
1380
1540
1700
15
15
15
19
19
19
19
19
19
19
19
23
23
23
23
23
25
25
25
27
27
27
33
33
33
33
33
33
33
33
39
39
39
45
45
4
4
4
4
4
4
4
4
8
8
8
8
8
12
12
12
12
16
16
16
20
20
20
24
24
24
24
28
28
28
28
28
32
36
40
90
95
100
125
135
140
155
175
200
210
225
270
305
-
350
-
430
480
540
605
675
730
795
845
-
-
-
-
-
-
-
-
-
-
-
65
70
75
90
100
105
120
140
160
170
185
225
260
-
305
-
380
430
480
540
605
660
720
770
-
-
-
-
-
-
-
-
-
-
-
15
15
15
19
19
19
19
19
23
23
23
25
25
-
25
-
27
27
33
33
33
33
39
39
-
-
-
-
-
-
-
-
-
-
-
4
4
4
4
4
4
8
8
8
8
8
8
12
-
12
-
12
16
16
16
20
20
20
24
-
-
-
-
-
-
-
-
-
-
-
호칭치수
Nominal
Size
가스키트내경
Gasket ID
d₂
가스키트외경
Gasket OD
D
보울트구멍의중심의경
Bolt hole Circle DiameterC
보울트구멍의경Bolt holeDiameterh
보울트구멍의수No. ofBolt hole
가스키트외경
Gasket OD
D
보울트구멍의중심의경
Bolt hole Circle DiameterC
보울트구멍의경Bolt holeDiameterh
보울트구멍의수No. ofBolt hole
호칭압력 10㎏/㎠플랜지용
(Nominal Pressure 10㎏/㎠Flange)
호칭압력 16㎏/㎠플랜지용
(Nominal Pressure 16㎏/㎠Flange)
KS.JIS 관 FLANGE용GASKET 치수(Gasket Dimensions for KS or JIS Flanges)
sung chang co.,ltd.│ 57
KS B 1519
JIS B 2202
참고 : 관플랜지의가스키트치수
다음에표시하는사항은참고로표시하는것이며, 규격의일부는아니다.
1. 가스키트는원칙으로비금속가스키트로한다.
2. 이 가스키트는주로시-트가스키팅에서잘라낸것으로한다.
Note : Gasket Dimensions for Pipe FlangesBelow are for reference only, no specification1. Below are based on non-metallic gasket.2. This is cut from gasket sheet.
●전면가스키트(Full face Gasket) F F Type
10
15
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
18
22
28
34
43
49
61
77
90
102
115
140
166
217
268
319
356
407
458
509
559
610
661
712
763
813
864
915
90
95
100
125
135
140
155
175
200
210
225
270
305
350
430
480
540
605
675
730
795
845
945
995
1080
1140
1200
1250
65
70
75
90
100
105
120
140
160
170
185
225
260
305
380
430
480
540
605
660
720
770
850
900
970
1030
1090
1140
15
15
15
19
19
19
19
19
23
23
23
25
25
25
27
27
33
33
33
33
39
39
48
48
56
56
56
56
4
4
4
4
4
4
8
8
8
8
8
8
12
12
12
16
16
16
20
20
20
24
24
24
24
24
24
28
110
115
120
130
140
160
165
200
210
230
240
275
325
370
450
515
550
630
-
-
-
-
-
-
-
-
-
-
75
80
85
95
105
120
130
160
170
185
195
230
275
320
390
450
495
560
-
-
-
-
-
-
-
-
-
-
19
19
19
19
19
23
19
23
23
25
25
25
27
27
33
33
33
39
-
-
-
-
-
-
-
-
-
-
4
4
4
4
4
4
8
8
8
8
8
8
12
12
12
16
16
16
-
-
-
-
-
-
-
-
-
-
호칭치수
Nominal
Size
가스키트내경
Gasket ID
d₂
가스키트외경
Gasket OD
D
보울트구멍의중심의경
Bolt hole Circle DiameterC
보울트구멍의경Bolt holeDiameterh
보울트구멍의수No. ofBolt hole
가스키트외경
Gasket OD
D
보울트구멍의중심의경
Bolt hole Circle DiameterC
보울트구멍의경Bolt holeDiameterh
보울트구멍의수No. ofBolt hole
호칭압력 2㎏/㎠플랜지용
(Nominal Pressure 2㎏/㎠ Flange)
호칭압력 5㎏/㎠플랜지용
(Nominal Pressure 5㎏/㎠ Flange)
KS.JIS 관 FLANGE용GASKET 치수(Gasket Dimensions for KS or JIS Flanges)
58 │ http://www.scgasket.co.kr
ASME B 16.21
ANSI B 16.5
● 전면가스키트(Full face Gasket) F F Type
1/2
3/4
1
1+1/4
1+1/2
2
2+1/2
3
3+1/2
4
5
6
8
10
12
14
16
18
20
24
21.3
26.9
33.3
42.2
48.5
60.5
73.2
88.9
101.6
114.3
141.2
168.1
218.9
273.1
323.9
355.6
406.4
457.2
508.0
609.6
88.9
98.6
108.0
117.4
127.0
152.4
177.8
190.5
215.9
228.6
254.0
279.4
342.9
406.4
482.6
533.4
596.9
635.0
698.5
812.8
60.5
69.9
79.2
88.9
98.6
120.7
139.7
152.4
177.8
190.5
215.9
241.3
298.5
362.0
431.8
476.3
539.8
577.9
635.0
749.3
4
4
4
4
4
4
4
4
8
8
8
8
8
12
12
12
12
16
20
20
16
16
16
16
16
19
19
19
19
19
22
22
22
25
25
28
28
32
32
35.1
95.3
117.4
124.0
133.4
155.5
165.1
190.5
209.6
228.6
254.0
279.4
317.5
381.0
-
-
-
-
-
-
-
66.6
82.6
88.9
98.6
114.3
127.0
149.4
168.2
184.2
200.2
235.0
270.0
330.2
-
-
-
-
-
-
-
4
4
4
4
4
8
8
8
8
8
8
12
12
-
-
-
-
-
-
-
16
19
19
19
22
22
22
22
22
22
22
22
25
-
-
-
-
-
-
-
NPS
(호칭경)
GASKET I.D
(내경)
150# 300#
O.D PCD No of Hole H.D O.D PCD No of Hole H.D
( 단위 : mm )
DIN 86071 ● 전면가스키트(Full face Gasket) F F Type
20253240506580100125150175200250300350400450500600700800900
29364753658193120146172200225282332363415467520620723825928
90100120130140160190210240265295320375440490540595645755860975-
657590100110130150170200225255280335395445495550600705810920-
444444448888121212161620202424-
111114141414181818181818182222222222262630-
10511514015016518520022025028531534039544550556561567078089510151115
75851001101251451601802102402702953504004605155656207258409501050
44444488888812121616202020242428
14141818181818181822222222222226262630303333
10511514015016518520022025028531534040546052058064071584091010251125
75851001101251451601802102402702953554104705255856507708409501050
444444888881212121616202020242428
14141818181818181822222226262630303336363939
105115140150165185200235270300330360425485555620-73084596010851185
7585100110125145160190220250280310370430490550-6607708759901090
4444488888121212161616-2020242428
14141818181818222626262630303336-3639424848
NPS
(호칭경)
I.D
(내경)
PN6 PN10 PN16 PN25
O.D PCB H.NO H.D O.D PCB H.NO H.D O.D PCB H.NO H.D O.D PCB H.NO H.D
( 단위 : mm )
KS B ISO. DIN(BAR) 관 FLANGE용GASKET 치수표
ANSI ASME 관 FLANGE용GASKET의치수표
sung chang co.,ltd.│ 59
GASKET & GLAND PACKING 전문기업성창이함께하겠습니다.
SUNG CHANG CO., LTD.SUNG CHANG CO., LTD.SUNG CHANG CO., LTD.
HEAD OFFICE & FACTORY :
부산광역시 강서구 대저2동 2494번지2494, Daejeo 2-dong, Gangseo-gu, Busan, KoreaTEL: +82-51-316-6300 FAX: +82-51-314-7171
E-mail : [email protected]
http://www.scgasket.co.kr