ANSYS 2011 中国用户大会优秀论文

Abstract — This paper presents a new topology of hybrid excitation synchronous machines (HESM) with dual-direction magnetic shunt rotor. Firstly, the configuration characteristic, basic operation principle, and equivalent magnetic circuit are introduced. Then, 3D-FEA model of the proposed HESM are established. 3D-FEA results demonstrate that the proposed HESM has wide field regulation range and fault-tolerant ability. It is an efficient topology that significantly broadens the application of HESM with magnetic shunt rotor.

I. INTRODUCTION

Hybrid excitation synchronous machines combine permanent-magnet (PM) excitation with wound field excitation. The goal behind using two excitation field sources is to combine advantages of PM excited machines and wound field synchronous machines. On one hand, HESM remains the advantages of high power density and high efficiency as conventional PM machines because of the existence of PMs. On the other hand, the engagement of wound field excitation makes it easy to adjust the main flux, which is fixed in PM machines. Due to these feathers, HESM is a new class of electric machine that has a bright further in vehicle drive system [1] and aircraft starter/generator system.

The development of HESM is proceeding rapidly recent years. Several typical hybrid excitation synchronous machines have been proposed in the scientific and technical literature [2]-[14]. The forgoing hybrid excited machines can be divided into two groups, depending on weather axial flux path exists in the stator or rotor. For the first group, axial flux path doesn’t exist. Hybrid excited switching-flux PM (HESFPM) was proposed in [2]. In order to locate the field winding, the outer diameter is significantly enlarged. Several hybrid-excited topologies were developed in [3]-[5]. Stator doubly fed doubly salient machine (SDFDSM) was proposed in [6] and further analyzed in [7]. Hybrid excited doubly salient machine, which was proposed in [8] and further researched in [9]. SDFDSM and HEDSPMM are similar in structure, both having permanent magnets and field winding in the stator. None of the three types of hybrid excited machine that mentioned above works with circular rotating field.

For the other group, axial flux path play an important role in the regulation action of field excitation to the field in the main air gap. The consequent-pole hybrid excitation PM

machine consists of a rotor divided into two sections and a circumferential field winding placed in the middle of the stator [10]-[11]. Homopolar and bipolar hybrid excitation synchronous was proposed in [12] and further analyzed in [13]. In [14], a novel multi-pole permanent magnet synchronous machine utilizing SMC bypass core for magnet flux and SMC field-pole core with toroidal coil for independent field strengthening and weakening was developed. Both of the three hybrid excitation synchronous machines mentioned above utilize magnetic stator shell to form an axial flux path, which significantly reduce the efficiency of field excitation.

Hybrid excitation synchronous machine with single-direction magnetic shunt rotor is developed on basis of conventional interior PM synchronous machines [15]. The field coil is located in magnetic bridge fixed in the end of the stator. An example of design, shown in [15], has proved that this structure is effective to obtain wide field regulation range. In order to obtain wide field regulation range, the reluctance of axial flux path is looked forward to be as small as possible. Hence, hybrid excitation synchronous machine with single-direction magnetic shunt rotor is essentially designed as short and thick in structure. For this reason, the application of the HESM with single-direction magnetic shunt rotor is restricted. This paper presents a new topology of HESM with dual-direction magnetic shunt rotor, which significantly broadens the application of HESM with magnetic shunt rotor.

II. CONSTRUCTION AND EQUIVALENT MAGNETIC CIRCUIT

A. Construction Fig. 1 shows a general view of the proposed HESM with

8 poles/48 slots as an example. To illustrate, nonmagnetic shaft and armature windings are omitted in Fig. 1. The stator core is exactly the same with that of the conventional permanent magnet synchronous machines. The rotor of the proposed HESM can be consider as composing of two rotors of the HESM with single-direction magnetic shunt rotor. Two N- and S-pole cores are magnetic in the axial and radial direction at the same time. The stationary magnetic bridge with toroidal field coil is jointed at each end of machine. Therefore, a brushless excitation structure is implemented. Two field windings can be connected in series or parallel according to different application.

Investigation of Field Regulation Performance of a New Hybrid Excitation Synchronous Machine with Dual-Direction Magnetic Shunt Rotor

Jianbin Han, Zhuoran Zhang, Shengjie Ma Jiangsu Key Laboratory of New Energy Generation and Power Conversion, Nanjing University of Aeronautics and

Astronautics, China E-mail: apsc-zzr@nuaa.edu.cn

This work was supported by National Natural Science Foundation of China under Award 50807023, Aeronautic Science Foundation of China under project 2010ZC52034, Aeronautic Science Technology Foundation of 611 Institute under project C1004-032, and Youth Science &Technology Innovation Fund of NUAA under project NS2010088.

ANSYS 2011 中国用户大会优秀论文

Fig. 1. General view of the proposed HESM

B. Radial/Axial Magnetic Circuit Characteristics Radial magnetic flux path and axial magnetic flux path exist at the same time in the proposed HESM， which is similar to the HESM with single-direction magnetic shunt rotor. Radial magnetic flux passes by the main air gap (effective air gap compared with auxiliary air gap is defined as main air gap). However, there are two axial flux paths corresponding to each radial flux path. Axial flux starts from the N-pole of the permanent magnet and passes by the N-pole core, auxiliary air gap 1a, magnetic bridge, auxiliary air gap 1b, S-pole core, and finally returns to the S pole of the permanent magnet, namely axial flux path1and path2 shown in Fig.2.

Fig. 2. Axial flux paths in the HESM

C. Equivalent Magnetic Circuit Performance of the proposed HESM are determined by

the relationship between main air gap magnetic field and electrical MMFs. Equivalent magnetic circuit method is helpful to the preliminary design of HESM. According to the principle of the proposed HESM, the equivalent magnetic circuit model is developed to make a rapid analysis of field regulation characteristics, which is shown in Fig. 3 and Fig. 4.

(a)

(b)

Fig.3. Loadless equivalent magnetic circuit model under positive excitation. (a) Fi1,Fi2 < Fab . (b) Fi1,Fi2 > Fab . (FPM —equivalent magnetic potential of permanent magnet; RPM—equivalent magnetic reluctance of permanent magnet; RδS , RδN —magnetic reluctance of the main air gap facing N pole piece and S pole piece respectively; RZ —magnetic reluctance of stator teeth; Rj —magnetic reluctance of stator yoke; RN1, RN2, RS1, RS2—magnetic reluctance of N pole rotor core and S pole rotor core respectively; Rcq1,Rcq2 —magnetic reluctance of magnetic bridge; Rδ1a, Rδ1b, Rδ2a, Rδ2b —magnetic reluctance of auxiliary air gap 1a, 1b, 2a and 2b.)

FPMFi1 Fi2

RPM

R N

R S

RZ

Rj

RN1

RS1

Rcq1

R 1a

R 1b

RN2

RS2

Rcq2

R 2a

R 2b

1 PM 2

(c)

ANSYS 2011 中国用户大会优秀论文

FPMFi1 Fi2

RPM

R N

R S

RZ

Rj

RN1

RS1

Rcq1

R 1a

R 1b

RN2

RS2

Rcq2

R 2a

R 2b

1 PM 2

(d)

Fig.4. Loadless equivalent magnetic circuit model under negative excitation.(a)Fab>0 . (b) Fab<0.

When the electrical MMF (Fi1, Fi2) is zero, permanent magnetic potential produces main air gap flux and axial magnetic flux by radial magnetic path and axial magnetic path, respectively. Under the positive electrical MMFs (Fi1, Fi2>0), axial magnetic flux (Φδ1，Φδ2) decreases, and magnetic flux in main air gap (Φδ increases. The equivalent magnetic circuit is given in Fig. 3(a). With the increase of electrical MMFs, axial magnetic flux will be reversed, and electrical MMFs further enhance the magnetic field in the main air gap. Fig. 3(b) shows the equivalent magnetic circuit in this case. When the electrical MMFs (Fi1, Fi2) is negative, axial magnetic flux increases, and main air gap flux is reduced, as shown in Fig. 4(a). Negative electrical MMFs can be so tremendous that main air gap flux may be reversed. This state is described in Fig. 4(b). However, in reality, due to the relatively low electrical MMFs compared to permanent MMFs, and the seriously saturated axial magnetic path, the state of magnetic path shown in Fig. 4(b) does not actually happen.

III. 3D-FEA RESULTS Table I gives key parameters of a design example. To analyze the magnetic field distribution and calculate

static characteristics of electrical machine, finite-element analysis (FEA) proves to be effective and accurate [16]–[19]. Due to the existence of axial flux path in the rotor of the proposed HESM, 3D-FEA method has been used to analyze the field regulation performance of the machine.

Table I PARAMETERS OF PROPOSED MACHINE

Number of slots 48 Number of pole-pairs 4

Out diameter of stator(mm) 270 Inner diameter of stator (mm) 210 Out diameter of rotor (mm) 206

Inner diameter of rotor (mm) 146 Main air gap length(mm) 2 Auxiliary air gap1(mm) 0.3 Auxiliary air gap2(mm) 0.3 Stator core length (mm) 80 Rotor core length (mm) 240

Turn-in-series per phase 24 This paper analyses the field distribution characteristics

of proposed HESM with different electrical MMFs by Maxwell 3D. Reasonable mesh is especially important for 3D-FEA. The satisfied 3D mesh of FEA model shown in Fig. 5 ensures the accuracy of 3D-FEA results. In order to observe the distribution of the flux density along the axial direction in the main air gap, three mark curves, curve1, curve2 and curve3 shown in Fig. 6, are defined.

Fig.5 Mesh of the 3D-FEA model Fig. 6 three mark line in main gapTwo field windings are allowed to be connected in series

or parallel. Different external excitation circuits make it easy to control the excitation current. According to the relationship of the current via the two field windings, the operating mode can be divided into two modes: symmetrical field excitation (Fi1=Fi2) and asymmetrical field excitation (Fi1≠Fi2).

A. Symmetrical field excitation (Fi1=Fi2)

(a)

ANSYS 2011 中国用户大会优秀论文

(b)

(c)

Fig. 7. Flux density vector in rotor and magnetic bridge with different field excitation.(a) Fi1=Fi2= -2000AT. (b) Fi1 =Fi2=0AT. (c) Fi1=Fi2= 4000AT.

Fig. 7 presents flux density vector of rotor core and magnetic bridge under the three typical conditions with different field excitation. When the field excitation is equal to 4000AT, the direction of axial flux is opposite to that with field excitation 0AT, as shown in Fig. 6. Whereas the direction of axial flux with field excitation -2000 AT is same as that with field excitation 0AT. As the field excitation decreasing to -2000AT, serious magnetic saturation in the transition parts of the rotor core resulting in limited decrease space for the main air gap flux density compared with that under field excitation 0AT.

(a)

(b)

(c)

Fig. 8 Flux density of main air gap with different excitation. (a) Fi1=Fi2=-2000AT, (b) Fi1=Fi2=0AT, (c) Fi1=Fi2=4000AT.

Fig. 9 Flux density of main air gap (Fi1=Fi2=4000AT)

ANSYS 2011 中国用户大会优秀论文

Fig. 8 shows the 3D results of flux density waveform in

the main air gap with different field excitation corresponding to cure1. In Fig. 9, the waveforms of flux density in the main air gap corresponding to different position in axial direction are nearly the same, which indicates that the flux density in the main air gap is well-distributed in axial direction.

Fig. 10. Relationship between main air gap flux density and electrical MMFs.

Fig. 11 Cloud picture of flux density of S-pole core when Fi1=Fi2=4000AT

The relationship between the average flux density in the main air-gap and electrical MMFs with different field excitation is shown in Fig. 10. Fig. 11 shows cloud picture of flux density of S-pole core when Fi1 and Fi2 is equal to the max field excitation 4000AT, which indicates the S-pole core is magnetic saturated. Field excitation higher than 4000AT can’t enhance the flux density in the main air gap any more. When the field excitation Fi1 and Fi2 varies from -2000AT to 4000AT, the average flux density in the main air-gap increases from 0.24T to 0.69T correspondingly, which imply the flux-strengthening capability is higher than the flux weakening capability. The flux density of main air-gap increases to 3 times nearly. According to the 3D-FEA results, the proposed HESM possesses the feature of a wide regulation range of the air-gap magnetic field.

B. Asymmetrical field excitation (Fi1≠Fi2)

Distance (mm)

0.00

0.20

0.40

350 550450400 500

0.60

0.10

0.30

0.50

0.70

Fig. 12 Flux density of main air gap (Fi1=0, Fi2=4000AT)

It is assumed that the two field windings are independent. When the field excitation Fi1 is zero and Fi2 is equal to 4000AT, the flux density in the main air gap shown in Fig. 12 indicates that the proposed HESM can still works in the case of one field winding is open circuit. Consequently, from the standpoint of reliability, the proposed HESM has fault-tolerant ability.

IV. CONCLUSION A new topology of HESM has been presented in this paper.

The construction, basic operation principle, and equivalent magnetic circuit are introduced in detail. The 3D-FEA results indicate the proposed HESM possess the characteristics as follows.

1) The flux density in the main air gap can be regulated by changing the current via the two field windings. The flux-strengthening capability is higher than the flux weakening capability.

2) The field regulation range of the proposed HESM is up to 2:1.

3) Setting two field windings in the proposed machine makes it more reliable. Even open-circuit fault occurs in either of field windings, the proposed machine can still work normally.

4) The proposed HESM is capable of meeting the requirement of large length-diameter ratio in some application.

REFERENCES

[1] Y. Amara, L. Vido, M. Gabsi and E. Hoang, “Hybrid excitation synchronous machines: energy-efficient solution for vehicles propulsion,” IEEE Transaction Vehicle Technology., Vol. 58, No. 5, pp. 2137-2149, Jun. 2009.

[2] E. Hoang, M. Lecrivain and M. Gabsi, “A new structure of a switching flux synchronous polyphased machine with hybrid excitation,” in 12th Eur. Conf. Power Electron. Appl., 2007, pp. 1–8.

[3] H. Wei, M. Cheng and G. Zhang, “A novel hybrid excitation flux-switching motor for hybrid vehicles”, IEEE Transaction on Magnetics, Vol. 45, No. 10, pp.4728-4731, Oct. 2009.

[4] R. L. Owen, Z. Q. Zhu and G. W. Jewell, “Hybrid-excited flux-switching permanent-magnet machines with iron flux bridges,” IEEE Transaction on Magnetics, Vol. 46, No. 6, pp.1726-1729, Jun. 2010.

ANSYS 2011 中国用户大会优秀论文

[5] J. T. Chen, Z. Q. Zhu S. Iwasaki, and R. P. Deodhar, “A novel hybrid-

excited switched-flux brushless AC machine for EV/HEV Applications,” IEEE Transaction on Vehicular Technology, Vol. 60, No. 4, pp. 1365-1373, May. 2011.

[6] K. T. Chau, M. Cheng and C. C. Chan, “Nonlinear magnetic circuit analysis for a novel stator doubly fed doubly salient machine,” IEEE Transaction on Magnetics, Vol. 38, No. 5, pp. 2382-2384, Sep. 2002.

[7] K. T. Chau, J. Z. Jiang and Y.Wang, “A novel stator doubly fed doubly salient permanent magnet brushless machine,” IEEE Transaction on Magnetics, Vol. 39, No. 5, pp. 3001–3003, Sep. 2003.

[8] Z. Chen and N. Zhou, “Flux Regulation ability of a hybrid excitation doubly salient machine,” IET Electric Power Applications, Vol. 5, No. 2, pp. 224-229, 2011.

[9] Z. Zhang, Y. Yang and Y. Yan, “Investigation of a new topology of hybrid excitation doubly salient brushless DC generator”, IEEE Transactions on Industrial Electronics, to be published.

[10] E. Spooner, S. A. W. Khatab and N. G. Nicolaou, “Hybrid excitation of AC and DC machines,” in Proc. IEE Int. Conf. Elect. Mach. Drives, Sep. 1989, pp. 48-52.

[11] J. A. Tapia, F. Leonardi and T. A. Lipo; “Consequent-pole permanent-magnet machine with extended field-weakening capability,” IEEE Transaction on Industrial Applications, Vol. 39, No. 5, pp. 1704-1709, Nov. 2003.

[12] Y. Amara, J. Lucidarme, M. Gabsi, M. Lecrivain, A.H.B. Ahmed and A. Akemakou, “A new topology of hybrid synchronous machine,” IEEE Transaction on Industrial Applications, Vol. 37, No. 5, pp.1273-1281, Sep. 2001.

[13] L. Vido, Y. Amara, M. Gabsi, M. Lecrivain and F. Chabot, “Compared performances of homopolar and bipolar hybrid excitation synchronous machines,” in Conf. Rec. Industry Appl. Conf., 40th IAS Annu. Meeting, Oct. , 2005, vol. 3, pp. 1555–1560.

[14] T. Kosaka, M. Sridharbabu, M. Yamamoto and N. Matsui, “Design studies on hybrid excitation motor for main spindle drive in machine tools”, IEEE Transaction on Industrial Electronics, Vol. 57, No. 11, pp. 3807-3813 Nov. 2010.

[15] Z. Zhang, Y Yang and S. Yang, “Principle of Operation and Feather Investigation of a New Topology of Hybrid Excitation Synchronous Machine,” IEEE Transactions on Magnetics, Vol. 44, No. 9, pp. 2174-2180, Aug. 2008.

[16] Z. Zhang, J. Zhou, D. Zhu and Y. Yan, “Architecture and principle of a novel coordinate structure hybrid excitation synchronous machine” International Conference on Electrical Machines and Systems, Oct. 2008, pp. 3497-3500.

[17] S. Ruoho, E. Dlala and A. Arkkio, “Comparison of demagnetization models for finite-element analysis of permanent-magnet synchronous machines,” IEEE Transaction on Magnetics, Vol. 43, No. 11, pp. 3964–3968, Nov. 2007.

[18] T. Finken and K. Hameyer, “Study of hybrid excited synchronous alternators for automotive applications using coupled FE and circuit simulations,” IEEE Transaction on Magnetics, Vol. 44, No. 6, pp. 1598–1601, Jun. 2008.

[19] X. Zhu, M. Chen Z. Wenxiang, C. Liu and K. T. Chau, “A new cosimulation approach to performance analysis of a hybrid excited doubly salient motor considering indirect field-circuit coupling,” IEEE Transaction on Magnetics, Vol. 43, No. 6, pp. 2558–2560, Jun. 2007.

Jianbin Han received the B.S. degree in electrical engineering from Nanjing University of Aeronautics and Astronautics (NUAA), Nanjing, China, in 2009. He is currently working toward the Master. degree in electrical engineering at the same university. His main research interests include permanent magnet machine, hybrid excitation synchronous machine. Zhuoran Zhang (M’09) was born in Anhui Province, China, in 1978. He received the B.S. degree in measurement engineering from NUAA, Nanjing, China, in 2000, the M.S. and Ph.D. degrees in electrical engineering from NUAA, in 2003 and 2009, respectively. He is currently a professor and the vice director in the Department of Electrical Engineering, College of Automation Engineering, NUAA. His

research interests include doubly salient electrical machine, permanent magnet machine, hybrid excitation electrical machine, renewable power system and aeronautical power supply systems. He has authored or coauthored of over 40 technical papers and is the holder of eleven patents in these areas. Shengjie Ma received the B.S. degree in electrical engineering from Anhui University, Hefei, China, in 2010. He is currently working toward the Master. degree in electrical engineering at NUAA, Nanjing, China.

His main research interests include design and simulation of hybrid excitation synchronous machine.