2007 toyota tundra. banco 2
TRANSCRIPT
![Page 1: 2007 Toyota Tundra. Banco 2](https://reader036.vdocuments.pub/reader036/viewer/2022081909/577c868a1a28abe054c199a9/html5/thumbnails/1.jpg)
8/20/2019 2007 Toyota Tundra. Banco 2
http://slidepdf.com/reader/full/2007-toyota-tundra-banco-2 1/4
7 Toyota Truck Tundra 4WD V8-4.7L (2UZ-FE) Copyright © 2011, ALLDATA 10.50PE Page 1
r Injection Control Valve: Service and Repair
r Switching Valve (For Bank 2)MOVAL
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTE:- Some systems need to be initialized after the cable is reconnected.
- After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.
REMOVE FRONT FENDER APRON SEAL RH
a. Remove the 5 clips and fender apron seal.
DISCONNECT NO. 1 WATER BY-PASS PIPE
a. Remove the 2 bolts and disconnect the water bypass pipe.
NOTE: Do not disconnect the hoses.
If it is necessary to disconnect the hoses, first drain the engine coolant.
DISCONNECT NO. 2 AIR INJECTION SYSTEM HOSEa. Disconnect the air injection system hose from the air switching valve.
REMOVE NO. 2 AIR TUBE
![Page 2: 2007 Toyota Tundra. Banco 2](https://reader036.vdocuments.pub/reader036/viewer/2022081909/577c868a1a28abe054c199a9/html5/thumbnails/2.jpg)
8/20/2019 2007 Toyota Tundra. Banco 2
http://slidepdf.com/reader/full/2007-toyota-tundra-banco-2 2/4
7 Toyota Truck Tundra 4WD V8-4.7L (2UZ-FE) Copyright © 2011, ALLDATA 10.50PE Page 2
a. Disconnect the air pump connector. b. Disconnect the wire harness clamp.
c. Remove the 4 nuts, No. 2 air tube and 2 gaskets.
NOTE: Be careful not to damage the installation surface of the gaskets.
REMOVE AIR SWITCHING VALVE ASSEMBLY
a. Remove the 3 nuts and air switching valve.
NOTE: Do not hold the bracket of the air switching valve.
TALLATION
INSTALL AIR SWITCHING VALVE ASSEMBLY
a. Install the air switching valve with the 3 nuts.
Torque: 16 N.m (163 kgf. cm, 12 ft.lbf)
![Page 3: 2007 Toyota Tundra. Banco 2](https://reader036.vdocuments.pub/reader036/viewer/2022081909/577c868a1a28abe054c199a9/html5/thumbnails/3.jpg)
8/20/2019 2007 Toyota Tundra. Banco 2
http://slidepdf.com/reader/full/2007-toyota-tundra-banco-2 3/4
7 Toyota Truck Tundra 4WD V8-4.7L (2UZ-FE) Copyright © 2011, ALLDATA 10.50PE Page 3
NOTE: Do not hold the bracket of the air switching valve.
INSTALL NO. 2 AIR TUBE
a. Temporarily install a new gasket and the No. 2 air tube to the exhaust manifold side with the 2 nuts. b. Install a new gasket and the No. 2 air tube to the air switching valve side with the 2 nuts.
Torque: 10 N.m (102 kgf. cm, 7 ft.lbf)
c. Tighten the 2 nuts on the exhaust manifold side.
Torque: 10 N.m (102 kgf. cm, 7 ft.lbf)
d. Connect the air pump connector.e. Connect the wire harness clamp.
INSTALL NO. 2 AIR INJECTION SYSTEM HOSE
a. Connect the air injection system hose to the air switching valve.
CONNECT NO. 1 WATER BY-PASS PIPE
a. Connect the water by-pass pipe with the 2 bolts.
Torque: 18 N.m (184 kgf. cm, 13 ft.lbf)
![Page 4: 2007 Toyota Tundra. Banco 2](https://reader036.vdocuments.pub/reader036/viewer/2022081909/577c868a1a28abe054c199a9/html5/thumbnails/4.jpg)
8/20/2019 2007 Toyota Tundra. Banco 2
http://slidepdf.com/reader/full/2007-toyota-tundra-banco-2 4/4
7 Toyota Truck Tundra 4WD V8-4.7L (2UZ-FE) Copyright © 2011, ALLDATA 10.50PE Page 4
INSTALL FRONT FENDER APRON SEAL RH
a. Install the fender apron seal with the 5 clips.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTE: Some systems need to be initialized after the cable is reconnected