2007 toyota tundra.banco 1
TRANSCRIPT
8/20/2019 2007 Toyota Tundra.banco 1
http://slidepdf.com/reader/full/2007-toyota-tundrabanco-1 1/4
7 Toyota Truck Tundra 4WD V8-4.7L (2UZ-FE) Copyright © 2011, ALLDATA 10.50PE Page 1
r Injection Control Valve: Service and Repair
r Switching Valve (For Bank 1)MOVAL
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTE:- Some systems need to be initialized after the cable is reconnected.
- After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.
REMOVE FRONT FENDER APRON SEAL LH
a. Remove the 5 clips and fender apron seal.
REMOVE NO. 2 AIR HOSE
a. Disconnect the air switching valve connector. b. Disconnect the fuel hose clamp.
c. Remove the air hose.
REMOVE NO. 3 AIR TUBE
8/20/2019 2007 Toyota Tundra.banco 1
http://slidepdf.com/reader/full/2007-toyota-tundrabanco-1 2/4
7 Toyota Truck Tundra 4WD V8-4.7L (2UZ-FE) Copyright © 2011, ALLDATA 10.50PE Page 2
a. Remove the 4 nuts, air tube and 2 gaskets.
NOTE: Be careful not to damage the installation surface of the gaskets.
REMOVE AIR SWITCHING VALVE ASSEMBLY
a. Remove the 3 nuts and air switching valve.
NOTE: Do not hold the bracket of the air switching valve.
TALLATION
INSTALL AIR SWITCHING VALVE ASSEMBLY
a. Install the air switching valve with the 3 nuts.
NOTE: Do not hold the bracket of the air switching valve.
Torque: 16 N.m (163 kgf. cm, 12 ft.lbf)
INSTALL NO. 3 AIR TUBE
8/20/2019 2007 Toyota Tundra.banco 1
http://slidepdf.com/reader/full/2007-toyota-tundrabanco-1 3/4
7 Toyota Truck Tundra 4WD V8-4.7L (2UZ-FE) Copyright © 2011, ALLDATA 10.50PE Page 3
a. Temporarily install a new gasket and the No. 3 air tube to the exhaust manifold side with the 2 nuts. b. Install a new gasket and the No. 3 air tube to the air switching valve side with the 2 nuts.
Torque: 10 N.m (102 kgf. cm, 7 ft.lbf)
c. Tighten the 2 nuts on the exhaust manifold side.
Torque: 10 N.m (102 kgf. cm, 7 ft.lbf)
INSTALL NO. 2 AIR HOSE
a. Install the No. 2 air hose.
b. Connect the air pump connector.
c. Connect the fuel hose clamp.
INSTALL FRONT FENDER APRON SEAL LH
a. Install the fender apron seal with the 5 clips.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
8/20/2019 2007 Toyota Tundra.banco 1
http://slidepdf.com/reader/full/2007-toyota-tundrabanco-1 4/4
7 Toyota Truck Tundra 4WD V8-4.7L (2UZ-FE) Copyright © 2011, ALLDATA 10.50PE Page 4
NOTE: Some systems need to be initialized after the cable is reconnected.