3412 60m desmontar mando de bomba

16/1/2016 3412C Marine Engine 60M05161-UP(SEBP3179 - 74) - Documentación

https://sis2001.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/sis… 1/7

Pantalla anteriorBienvenido: r050gxs2

Producto: MARINE ENGINEModelo: 3412 MARINE ENGINE 60M06236Configuración: 3412C Marine Engine 60M05161UP

Desarmado y Armado 3408C & 3412C MARINE ENGINESNúmero de medio SENR109500 Fecha de publicación 11/10/1996 Fecha de actualización 18/10/2012

SENR10950022

Governor & Fuel Pump Drive

SMCS - 1288-010; 1288-015; 1288-016

Remove & Install Governor & Fuel Pump Drive

Start By:

a. remove front housing cover

Typical Example

1. Remove cover (1).



Typical Example

2. Install Tool (A).

3. Remove plug (2).

Typical Example

4. Install Tool (B).

5. Turn the engine counterclockwise (as seen from the flywheel end of engine) with Tool (A) until No. 1piston is at top center (TC) on the compression stroke and Tool (B) can be installed in the flywheel. See thetopic "Finding Top Center Compression Position For No. 1 Piston" in the Systems Operation Testing &Adjusting Manual.

6. Put an alignment mark on governor and fuel pump drive (3).

7. Remove four bolts (4) and retainer (5).



8. Remove governor and fuel pump drive (3).

NOTE: The following steps are for the installation of the governor and fuel pump drive.

Typical Example

9. Remove cover (1).

Typical Example

10. Install Tool (A).

11. Remove plug (2).

Typical Example



12. Install Tool (B).

13. Turn the engine counterclockwise (as seen from the flywheel end of engine) with Tool (A) until No. 1piston is at top center (TC) on the compression stroke and Tool (B) can be installed in the flywheel. See thetopic "Finding Top Center Compression Position For No. 1 Piston" in the Systems Operation Testing &Adjusting Manual.

NOTE: Lubricate the weights and slides inside the governor and fuel pump drive with clean engine oilprior to installation.

NOTE: Inspect gasket (6) for damage or wear, if necessary replace with a new gasket.

14. Install governor and fuel pump drive (3) in position according to the alignment mark.

15. Install retainer (5) and four bolts (4). Tighten four bolts (4) to a torque of 136 ± 7 N·m (101 ± 5 lb ft).

16. Install plug (2) and cover (1).

End By:

a. install front housing cover



Disassemble Governor & Fuel Pump Drive

Start By:

a. remove governor and fuel pump drive



1. Remove flange assembly (1).

2. Remove two springs (2) and two weights (3) from drive gear assembly (4).

3. Remove two slides (5) from pistons (6).

4. Separate drive gear assembly (4) from advance sleeve (7).

Assemble Governor & Fuel Pump Drive

1. Put weights (3) in position in flange assembly (1) as shown.

2. Install springs (2) in flange assembly (1).



4. Use 1P-0808 General Purpose Lubricantto hold slides (5) in position on drive gear assembly (4).Install slides (5) on pistons (6).

5. Install advance sleeve (7) to drive gear assembly (4).

6. Install drive gear assembly (4) on flange assembly (1). Make sure slides (5) fit in grooves of the weights.

End By:

a. install governor and fuel pump drive

Copyright 1993 2016 Caterpillar Inc.Todos los derechos reservados.Red privada para licenciados del SIS.

Sat Jan 16 2016 08:39:58 GMT0300 (Hora estándar de Argentina) r050gxs2

3412 60m desmontar mando de bomba

Documents