7409 july 2012 phenguard 930 ( english ) - c.g....

July 2012

page 1/5

5 pages Revision of March 2011

PHENGUARD 930

two component high build amine adduct cured novolac phenolic epoxy primer

– primer coat in the Phenguard tankcoating system – excellent resistance to a wide range of organic acids, alcohols, edible oils,

fats (regardless of free fatty acid content) and solvents – maximum cargo fl exibility – low cargo absorption – good resistance to hot water – recognized corrosion control coating (Lloyd's register), see sheet 1886 – good application properties, resulting in a smooth surface

offwhite – eggshell

(1 g/cm³ = 8.35 lb/US gal; 1 m²/l = 40.7 ft²/US gal)

(data for mixed product)

1.7 g/cm³ 66% ± 2% max. 191 g/kg (Directive 1999/13/EC, SED) max. 315 g/l (approx. 2.6 lb/gal)(UK PG 6/23(92) Appendix 3)

Recommended dry fi lm thickness 100 μm * Theoretical spreading rate 6.6 m²/l for 100 μm *

2 hours at 20 °C min. 36 hours * max. 21 days * see curing table * at least 12 months * see additional data

– steel; blast cleaned in situ to at least ISO-Sa2½ and free from rust, scale, shop primer and any other contamination

– blasting profi le 50 - 100 μm – the substrate must be perfectly dry before and during application of

Phenguard 930 – substrate temperature must be above 10°C and at least 3°C above dew

point during application and curing

marine system sheet: 3141

tankcoatings system sheet: 3322

Description

PRINCIPAL CHARACTERISTICS

COLOURS AND GLOSS

BASIC DATA AT 20 °C

Mass density Volume solids VOC (Directive 1999/13/EC, SED) VOC (UK PG 6/23(92) appendix 3)

Touch dry after

Overcoating interval

Full cure after Shelf life (cool and dry place)

RECOMMENDEDSUBSTRATE CONDITIONSAND TEMPERATURES

SYSTEM SPECIFICATION

July 2012

page 2/5

PHENGUARD 930

mixing ratio by volume: base to hardener 88 : 12

– the temperature of the mixed base and hardener should preferably be above 15°C, otherwise extra solvent may be required to obtain application viscosity

– too much solvent results in reduced sag resistance and slower cure – thinner should be added after mixing the components

4 hours at 20 °C * – allow induction time before use – 15°C - 20 min. – 20°C - 15 min. – 25°C - 10 min.

Recommended thinner Thinner 91-92Volume of thinner 0 - 10%, depending on required thickness and application conditionsNozzle orifi ce 2 mmNozzle pressure 0.3 MPa (= approx. 3 bar; 44 p.s.i.)

Recommended thinner Thinner 91-92Volume of thinner 0 - 10%, depending on required thickness and application conditionsNozzle orifi ce approx. 0.46 - 0.53 mm (= 0.018 - 0.021 in)Nozzle pressure 15 MPa (= approx. 150 bar; 2176 p.s.i.)

only for spot repair and stripe coatingRecommended thinner Thinner 91-92Volume of thinner 0 - 5%

– Thinner 90-53

Film thickness and spreading rate

theoritical spreading rate m2/l 6.6 5.3

dft in μm 100 125

Maximum dft when brushing: 60 μm

Overcoating table for Phenguard 935

substrate temperature

10°C 15°C 20°C 30°C 40°C

minimum interval 60 hours 48 hours 36 hours 24 hours 16 hours

maximum interval 28 days 25 days 21 days 14 days 7 days

– surface should be dry and free from any contamination

INSTRUCTIONS FOR USE

Pot life Induction time

AIR SPRAY

AIRLESS SPRAY

BRUSH/ROLLER

CLEANING SOLVENT

July 2012

page 3/5

PHENGUARD 930

Curing table for Phenguard tankcoating system before transport of cargoes without note 4, 7, 8 or 11 and ballast water and tanktest with sea water

substrate temperature Service10°C 14 days15°C 14 days20°C 10 days30°C 7 days40°C 5 days

– minimum curing time of Phenguard tankcoating system before transport of cargoes with note 4, 7, 8 or 11: 3 months

– for detailed information on resistance and resistance notes, please refer to the latest issue of the Cargo Resistance List

– for transport of methanol and vinyl acetate monomer, a hot cure is required which cannot be substituted by a service period of 3 months with non-aggressive cargoes

– adequate ventilation must be maintained during application and curing (please refer to sheets 1433 and 1434)

– the performance of the applied system strongly depends on the curing degree of the fi rst coat at time of recoating. Therefore overcoating time between 1st and 2nd coat is extended in comparison between 2nd and 3rd coat (see overcoating details)

– when used as a primer under solvent free tank-linings the dft must be limited to a maximum of 100 μm

Pot life (at application viscosity)

10 °C 6 hours20 °C 4 hours30 °C 1.5 hour

Whilst it is always the aim of Sigma Coatings to supply the same product on a worldwide basis, slight modifi cation of the product is sometimes necessary to comply with local or national rules/circumstances.Under these circumstances an alternative product data sheet is used.

Curing

Worldwide availability

July 2012

page 4/5

PHENGUARD 930

Conversion tabels see information sheet 1410 Explanation to product data sheets see information sheet 1411 Safety indications see information sheet 1430 Safety in confi ned spaces and health safetyExplosion hazard - toxic hazard see information sheet 1431 Safe working in confi ned spaces see information sheet 1433 Directives for ventilation practice see information sheet 1434 Cleaning of steel and removal of rust see information sheet 1490 Specifi cation for mineral abrasives see information sheet 1491 Relative humidity - substrate temperature -air temperature see information sheet 1650

– for paint and recommended thinners see safety sheets 1430, 1431 and relevant material safety data sheets

– this is a solvent borne paint and care should be taken to avoid inhalation of spray mist or vapour as well as contact between the wet paint and exposed skin or eyes

REFERENCES

SAFETY PRECAUTIONS

July 2012

page 5/5

PHENGUARD 930

WARRANTY PPG warrants (i) its title to the product, (ii) that the quality of the product conforms to PPG’s specifi cations for such product in effect at the time of manufacture and (iii) that the product shall be delivered free of the rightful claim of any third person for infringement of any U.S. patent covering the product.

THESE ARE THE ONLY WARRANTIES THAT PPG MAKES AND ALL OTHER EXPRESS OR IMPLIED WARRANTIES, UNDER STATUTE OR ARISING OTHERWISE IN LAW, FROM A COURSE OF DEALING OR USAGE OF TRADE, INCLUDING WITHOUT LIMITATION, ANY OTHER WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR USE, ARE DISCLAIMED BY PPG.

Any claim under this warranty must be made by Buyer to PPG in writing within fi ve (5) days of Buyer’s discovery of the claimed defect, but in no event later than the expiration of the applicable shelf life of the product, or one year from the date of the delivery of the product to the Buyer, whichever is earlier. Buyer’s failure to notify PPG of such non-conformance as required herein shall bar Buyer from recovery under this warranty.

LIMITATIONS OF LIABILITY IN NO EVENT WILL PPG BE LIABLE UNDER ANY THEORY OF RECOVERY (WHETHER BASED ON NEGLIGENCE OF ANY KIND, STRICT LIABILITY OR TORT) FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES IN ANY WAY RELATED TO, ARISING FROM, OR RESULTING FROM ANY USE MADE OF THE PRODUCT.

The information in this data sheet is intended for guidance only and is based upon laboratory tests that PPG believes to be reliable. PPG may modify the information contained herein at any time as a result of practical experience and continuous product development. All recommendations or suggestions relating to the use of the PPG product, whether in technical documentation, or in response to a specifi c inquiry, or otherwise, are based on data, which to the best of PPG’s knowledge, is reliable. The product and related information is designed for users having the requisite knowledge and industrial skills in the industry and it is the end-user’s responsibility to determine the suitability of the product for its own particular use and it shall be deemed that Buyer has done so, as its sole discretion and risk.

PPG has no control over either the quality or condition of the substrate, or the many factors affecting the use and application of the product. Therefore, PPG does not accept any liability arising from any loss, injury or damage resulting from such use or the contents of this data sheet (unless there are written agreements stating otherwise).Variations in the application environment, changes in procedures of use, or extrapolation of data may cause unsatisfactory results.

This data sheet supersedes all previous versions and it is the Buyer’s responsibility to ensure that this data sheet is current prior to using the product. Current data sheets for all PPG Protective & Marine Coatings products are maintained at www.ppgpmc.com.The English text of this data sheet shall prevail over any translation thereof.

PDS 7409

180706 offwhite 7001002200

November 2012

page 1/5

5 pages Revision of July 2012

PHENGUARD 935

two component high build amine adduct cured novolac phenolic epoxy coating

– second coat in the Phenguard tankcoating system – excellent resistance to a wide range of organic acids, alcohols, edible oils,

fats (regardless of free fatty acid content) and solvents – maximum cargo fl exibility – low cargo absorption – good resistance to hot water – recognized corrosion control coating (Lloyd's register), see sheet 1886 – good application properties, resulting in a smooth surface

pink – eggshell



1.7 g/cm³ 66% ± 2% max. 191 g/kg (Directive 1999/13/EC, SED) max. 315 g/l (approx. 2.6 lb/gal)


2 hours at 20 °C min. 24 hours * max. 21 days * see curing table *

(data for components) at least 12 months * see additional data

– previous coat of Phenguard 930; dry and free from any contamination – the substrate must be perfectly dry before and during application of



marine system sheet: 3141 tankcoatings system sheet: 3322

Description


COLOURS AND GLOSS



Touch dry after Overcoating interval

Full cure after

Shelf life (cool and dry place)



November 2012

page 2/5

PHENGUARD 935

mixing ratio by volume: base to hardener 88 : 12 – the temperature of the mixed base and hardener should preferably be

above 15°C, otherwise extra solvent may be required to obtain application viscosity


allow induction time before use15°C - 20 min.20°C - 15 min.25°C - 10 min.

4 hours at 20 °C *see additional data



Recommended thinner Thinner 91-92Volume of thinner 0 - 5%

Thinner 90-53


theoritical spreading rate m²/l 6.6 5.3

dft in μm 100 125



Induction time

Pot life

AIR SPRAY

AIRLESS SPRAY

BRUSH/ROLLER

CLEANING SOLVENT

November 2012

page 3/5

PHENGUARD 935



10°C 15°C 20°C 30°C 40°C




Min.curing time of Phenguard tankcoating system before transport of cargoes without note 4, 7, 8 or 11 and ballast water and tanktest with sea water









Curing

November 2012

page 4/5

PHENGUARD 935

It is always the aim of PPG Protective and Marine Coatings to supply the same product on a worldwide basis. However, slight modifi cation of the product is sometimes necessary to comply with local or national rules/circumstances. Under these circumstances an alternative product data sheet is used





REFERENCES

SAFETY PRECAUTIONS

November 2012

page 5/5

PHENGUARD 935

WARRANTY PPG warrants (i) its title to the product, (ii) that the quality of the product conforms to PPG’s specifi cations for such product in effect at the time of manufacture and (iii) that the product shall be delivered free of the rightful claim of any third person for infringement of any U.S. patent covering the product. THESE ARE THE ONLY WARRANTIES THAT PPG MAKES AND ALL OTHER EXPRESS OR IMPLIED WARRANTIES, UNDER STATUTE OR ARISING OTHERWISE IN LAW, FROM A COURSE OF DEALING OR USAGE OF TRADE, INCLUDING WITHOUT LIMITATION, ANY OTHER WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR USE, ARE DISCLAIMED BY PPG. Any claim under this warranty must be made by Buyer to PPG in writing within fi ve (5) days of Buyer’s discovery of the claimed defect, but in no event later than the expiration of the applicable shelf life of the product, or one year from the date of the delivery of the product to the Buyer, whichever is earlier. Buyer’s failure to notify PPG of such non-conformance as required herein shall bar Buyer from recovery under this warranty.

LIMITATIONS OF LIABILITY IN NO EVENT WILL PPG BE LIABLE UNDER ANY THEORY OF RECOVERY (WHETHER BASED ON NEGLIGENCE OF ANY KIND, STRICT LIABILITY OR TORT) FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES IN ANY WAY RELATED TO, ARISING FROM, OR RESULTING FROM ANY USE MADE OF THE PRODUCT. The information in this sheet is intended for guidance only and is based upon laboratory tests that PPG believes to be reliable. PPG may modify the information contained herein at any time as a result of practical experience and continuous product development. All recommendations or suggestions relating to the use of the PPG product, whether in technical documentation, or in response to a specifi c inquiry, or otherwise, are based on data, which to the best of PPG’s knowledge, is reliable. The product and related information is designed for users having the requisite knowledge and industrial skills in the industry and it is the end-user’s responsibility to determine the suitability of the product for its own particular use and it shall be deemed that Buyer has done so, as its sole discretion and risk. PPG has no control over either the quality or condition of the substrate, or the many factors affecting the use and application of the product. Therefore, PPG does not accept any liability arising from any loss, injury or damage resulting from such use or the contents of this information (unless there are written agreements stating otherwise). Variations in the application environment, changes in procedures of use, or extrapolation of data may cause unsatisfactory results. This sheet supersedes all previous versions and it is the Buyer’s responsibility to ensure that this information is current prior to using the product. Current sheets for all PPG Protective & Marine Coatings Products are maintained at www.ppgpmc.com. The English text of this sheet shall prevail over any translation thereof.

PDS 7435

179115 pink 6007002200

July 2012

page 1/5

5 pages Revision of March 2011

PHENGUARD 940

two component high build amine adduct cured novolac phenolic epoxy fi nish

– fi nish coat in the Phenguard tankcoating system – excellent resistance to a wide range of organic acids, alcohols, edible oils,

fats (regardless of free fatty acid content) and solvents – maximum cargo fl exibility – low cargo absorption – good resistance to hot water – recognized corrosion control coating (Lloyd's register), see sheet 1886 – good application properties, resulting in a smooth surface – easy to clean

light grey – eggshell



1.7 g/cm³ 66% ± 2% max. 191 g/kg (Directive 1999/13/EC, SED) max. 315 g/l (approx. 2.6 lb/gal)


2 hours at 20 °C min. 24 hours * max. 21 days * see curing table * at 20 °C * see additional data

at least 12 months * see additional data

– previous coat of Phenguard 935; dry and free from any contamination – the substrate must be perfectly dry before and during application of



Description


COLOURS AND GLOSS



Touch dry after

Overcoating interval

Full cure after



July 2012

page 2/5

PHENGUARD 940

marine system sheet: 3141 tankcoatings system sheet: 3322

mixing ratio by volume: base to hardener 88 : 12 – the temperature of the mixed base and hardener should preferably be

above 15°C, otherwise extra solvent may be required to obtain application viscosity


4 hours at 20 °C * *see additional data

– allow induction time before use – 15°C - 20 min. – 20°C - 15 min. – 25°C - 10 min.



Recommended thinner Thinner 91-92Volume of thinner 0 - 5%

Thinner 90-53


theoritical spreading rate m2/l 6.6 5.3

dft in μm 100 125




Pot life

Induction time

AIR SPRAY

AIRLESS SPRAY

BRUSH/ROLLER

CLEANING SOLVENT

July 2012

page 3/5

PHENGUARD 940



10°C 15°C 20°C 30°C 40°C




Min.curing time of Phenguard tankcoating system before transport of cargoes without note 4, 7, 8 or 11 and ballast water and tanktest with sea water









Whilst it is always the aim of Sigma Coatings to supply the same product on a worldwide basis, slight modifi cation of the product is sometimes necessary to comply with local or national rules/circumstances.Under these circumstances an alternative product data sheet is used.

Curing


July 2012

page 4/5

PHENGUARD 940




REFERENCES

SAFETY PRECAUTIONS

July 2012

page 5/5

PHENGUARD 940

WARRANTY PPG warrants (i) its title to the product, (ii) that the quality of the product conforms to PPG’s specifi cations for such product in effect at the time of manufacture and (iii) that the product shall be delivered free of the rightful claim of any third person for infringement of any U.S. patent covering the product.

THESE ARE THE ONLY WARRANTIES THAT PPG MAKES AND ALL OTHER EXPRESS OR IMPLIED WARRANTIES, UNDER STATUTE OR ARISING OTHERWISE IN LAW, FROM A COURSE OF DEALING OR USAGE OF TRADE, INCLUDING WITHOUT LIMITATION, ANY OTHER WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR USE, ARE DISCLAIMED BY PPG.

Any claim under this warranty must be made by Buyer to PPG in writing within fi ve (5) days of Buyer’s discovery of the claimed defect, but in no event later than the expiration of the applicable shelf life of the product, or one year from the date of the delivery of the product to the Buyer, whichever is earlier. Buyer’s failure to notify PPG of such non-conformance as required herein shall bar Buyer from recovery under this warranty.

LIMITATIONS OF LIABILITY IN NO EVENT WILL PPG BE LIABLE UNDER ANY THEORY OF RECOVERY (WHETHER BASED ON NEGLIGENCE OF ANY KIND, STRICT LIABILITY OR TORT) FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES IN ANY WAY RELATED TO, ARISING FROM, OR RESULTING FROM ANY USE MADE OF THE PRODUCT.

The information in this data sheet is intended for guidance only and is based upon laboratory tests that PPG believes to be reliable. PPG may modify the information contained herein at any time as a result of practical experience and continuous product development. All recommendations or suggestions relating to the use of the PPG product, whether in technical documentation, or in response to a specifi c inquiry, or otherwise, are based on data, which to the best of PPG’s knowledge, is reliable. The product and related information is designed for users having the requisite knowledge and industrial skills in the industry and it is the end-user’s responsibility to determine the suitability of the product for its own particular use and it shall be deemed that Buyer has done so, as its sole discretion and risk.

PPG has no control over either the quality or condition of the substrate, or the many factors affecting the use and application of the product. Therefore, PPG does not accept any liability arising from any loss, injury or damage resulting from such use or the contents of this data sheet (unless there are written agreements stating otherwise).Variations in the application environment, changes in procedures of use, or extrapolation of data may cause unsatisfactory results.

This data sheet supersedes all previous versions and it is the Buyer’s responsibility to ensure that this data sheet is current prior to using the product. Current data sheets for all PPG Protective & Marine Coatings products are maintained at www.ppgpmc.com.The English text of this data sheet shall prevail over any translation thereof.

PDS 7436

179118 grey 5000002200

/5

March 20115 pages Revision of April 2009

PHENGUARD 965

two component high build amine adduct cured novolac phenolic epoxy coating

– Phenguard 965 system excellent resistance to a wide range of organic acids, alcohols, fats –(regardless of free fatty acid content) and solvents maximum cargo fl exibility – low cargo absorption – easy to clean – good resistance to hot water – can be applied and cures at temperatures down to 41°F (+5°C) – good application properties, resulting in a smooth surface –

off-white, pink, grey - eggshell

(8.25 lb/US gal = 1 g/cm³; 40.7 ft²/US gal = 1 m²/l) (data for mixed product) 14.19 lbs/gal (1.7 g/cm³) 68 ± 2% max. 195 g/kg (Directive 1999/13/EC, SED) max. 2.7 lb/gal (approx. 329 g/l) 4 mils (100 µm) * 276 ft²/gal (6.8 m²/l) for 4 mils (100 µm) * 2 - 3 hours at 68°F (20°C), 14 - 16 hours at 41°F (5°C) min. 8 hours * max. 14 days * see curing table *

(data for components)

at least 12 months * see additional data

– steel; blast cleaned in-situ to at least SSPC SP10/NACE 2 (ISO-Sa2½) and free from rust, scale, shop primer and any other contamination blasting profi le 2 - 4 mils (50 - 100 µm) – the substrate must be perfectly dry before and during application of –Phenguard 965 substrate temperature must be above 41°F (5°C) and at least 5°F (3°C) –above dew point during application and curing

Phenguard 965 off-white 4 mils (100 µm) Phenguard 965 pink 4 mils (100 µm) Phenguard 965 grey 4 mils (100 µm)

DESCRIPTION


COLORS AND GLOSS

BASIC DATA AT 68°F

Mass density Solids content VOC (supplied - EPA 24) Recommended dry fi lm thickness Theoretical spreading rate Touch dry after Overcoating interval

Full cure after




/5

March 2011

PHENGUARD 965

mixing ratio by volume: base to hardener 87 : 13

the temperature of the mixed base and hardener should preferably be above –59°F (15°C), otherwise extra solvent may be required to obtain application viscosity too much solvent results in reduced sag resistance – thinner should be added after mixing the components –

allow induction time before use41°F (5°C) - 20 min.50°F (10°C) - 15 min.59°F (15°C) - 10 min.

2 hours at 68°F (20°C) * * see additional data

Thinner 91-92 5 - 10%, depending on required thickness and application conditions approx. 0.018" - 0.021" inch (= 0.46 - 0.53 mm) 2130 p.s.i. (= approx. 15 MPa; 150 bar)

Thinner 91-92 5 - 10%, depending on required thickness and application conditions 0.078" inch (2 mm) 43 p.s.i. (= approx. 0.3 MPa or 3 bar)

Thinner 91-92 0 - 5%

Thinner 90-53

for paint and recommended thinners see safety sheets 1430, 1431 and relevant material safety data sheets

this is a solvent borne paint and care should be taken to avoid inhalation of spray mist or vapor as well as contact between the wet paint and exposed skin or eyes


Induction time

Pot life

AIRLESS SPRAY Recommended thinner Volume of thinner Nozzle orifi ce Nozzle pressure

CONVENTIONAL SPRAY Recommended thinner Volume of thinner Nozzle orifi ce Nozzle pressure

BRUSH/ROLLER Recommended thinner Volume of thinner

CLEANING SOLVENT

SAFETY PRECAUTIONS

/5

March 2011

PHENGUARD 965


theoretical spreading rate ft²/gal (m²/l)

276 (6.8) 220 (5.4) dft in mil (µm)

4 (100)

5 (125)

max. dft when brushing: 2.4 mils (60 µm)

Overcoating table for Phenguard 965 for dft up to 4 mils (100 µm)


41°F(5°C) 50°F(10°C) 59°F(15°C) 68°F(20°C) 86°F(30°C)

s epoksi premazima minimum interval

24 hours 20 hours 14 hours 8 hours 6 hours

sa poliuretanima maximum interval

28 days 25 days 21 days 14 days 7 days

surface should be dry and free from any contamination –

Curing table for dft up to 4 mils (100 µm)


min. curing time of Phenguard 965 system before transport of cargoes without note 4, 7, 8 or 11 and ballast water and tank test with sea water

41°F(5°C) 7 days

50°F(10°C) 5 days 59°F(15°C) 4 days68°F(20°C) 3 days 86°F(30°C) 2 days

minimum curing time of Phenguard 965 system before transport of cargoes –with note 4, 7, 8 or 11: 3 months for detailed information on resistance and resistance notes, please refer to –the latest issue of the Cargo Resistance List for transport of methanol and vinyl acetate monomer, a hot cargo cure is –required which cannot be substituted by a service period of 3 months with non-aggressive cargoes adequate ventilation must be maintained during application and curing –(please refer to sheets 1433 and 1434) when used as a primer under solvent free tank-linings the dft must be limited –to a maximum of 4 mils (100 µm)

ADDITIONAL DATA

/5

March 2011

PHENGUARD 965


41°F(5°C) 8 hours50°F(10°C) 6 hours59°F(15°C) 4 hours68°F(20°C) 2 hours86°F(30°C) 1 hour

Whilst it is always the aim of PPG Protective & Marine Coatings to supply the same product on a worldwide basis, slight modifi cation of the product is sometimes necessary to comply with local or national rules/circumstances.Under these circumstances an alternative product data sheet is used.

Explanation to product data sheets see information sheet 1411 Safety indications see information sheet 1430 Safety in confi ned spaces and health safetyExplosion hazard - toxic hazard see information sheet 1431 Safe working in confi ned spaces see information sheet 1433 Directives for ventilation practice see information sheet 1434 Cleaning of steel and removal of rust see information sheet 1490


REFERENCES

/5

March 2011

PHENGUARD 965

LIMITATION OF LIABILITY

The information in this data sheet is based upon laboratory tests we believe to be accurate and is intended for guidance only. All recommendations or suggestions relating to the use of the Sigma Coatings products made by PPG Protective & Marine Coatings, whether in technical documentation, or in response to a specifi c enquiry, or otherwise, are based on data which to the best of our knowledge are reliable. The products and information are designed for users having the requisite knowledge and industrial skills and it is the end-user's responsibility to determine the suitability of the product for its intended use.

PPG Protective & Marine Coatings has no control over either the quality or condition of the substrate, or the many factors affecting the use and application of the product. PPG Protective & Marine Coatings therefore does not accept any liability arising from loss, injury or damage resulting from such use or the contents of this data sheet (unless there are written agreements stating otherwise).

The data contained herein are liable to modifi cation as a result of practical experience and continuous product development.This data sheet replaces and annuls all previous issues and it is therefore the user's responsibility to ensure that this sheet is current prior to using the product.

In the event of any disparity or dispute in the wording of this document, the original English text shall prevail.

PDS 7959 199289 off-white 7001002200 199282 pink 6007002200 199284 grey 5000002200

7409 july 2012 phenguard 930 ( english ) - c.g....

Documents