2013 - plastisol anglais
Post on 29-Mar-2016
216 Views
Preview:
DESCRIPTION
TRANSCRIPT
PPPVVVCCC CCCOOOAAATTTIIINNNGGG
OOONNN RRREEEQQQUUUEEESSSTTT
� Without DEHP
(di-2-ethylhexylphthalate)
� Without VCM
(Vinyl Chloride Monomer)
CHEMICAL PROTECTION
ELECTRICAL INSULATION
SHOCKS RESISTANCE
ENCAPSULATION
Parc d’activité des 70 arpents Rue de Belloy 95 560 MONTSOULT (F)
Tel : 33 (0) 134 699 510 Fax :33 (0) 134 696 790 Mobile : 0 786 252 877
contact@sts-eco-planete-industrie.fr
MAX PHYSICAL FEATURES OF PARTS TO BE COATED Height (H) 2 000 mm max
Length (L) 1 400 mm max
Width (l) 900 mm max
Weight 400 Kg max
IDENTIFICATION Type of utilisation
Coating, molding
CHEMICAL CONSTITUENTS PVC - PLASTIFIANT, PIGMENTS, STABILISERS PHYSICAL PROPERTIES
- Physical description
- Typical temperature
- Temperature of self- inflammation
- volumic mass
Liquid with viscosity
Boiling temperature > at 200°C
>200°C
~1180 Kg/ M3
* Storage temperature 5°C < T° < 25°C
* shelf life 3 months with closed package
*VISCOSITY - Brook Field LVF Viscosimeter
. Speed
. Needle
. Viscosity at 25°C
6 t/mn
N° 4
75000 +/-15000 mPa.s
* RHEOLOGICAL BEHAVIOUR Thixotrope * DENSITY AT 20°C
(pycnometer method) ~ 1,18
* Working temeperature ~ 190°C * Dilution features
. Thinner reference
. maximum ponderal dose
Thinner for green plastisol
2 % * HARDNESS AT 25°C AFTER POLYMÉRISATION 80 +/- 4 Shore A
IDENTIFICATION Type of utilisation
PRIMER OF ADHERENCE Under-layer for adherence of Plastisol
CHEMICAL CONSTITUENTS Preparation of acrylic resin, phenolic, solvants or aqueous version
PHYSICAL PROPERTIES
- Physical description
- Flash point
- Temperature of self- inflammation
- Volumic mass
- Other data
White liquid
-6°C
>400°C
950 Kg/m3
Dry extract ~ 20%
PLASTISOL ON METALS ARE ONLY USED FOR INDUSTRY APPLICATIONS AND FORMULATED WITH PVC, LIQUID PLASTICIZERS, MIXTURE OF THIXOTROPIANTS, THERMAL STABILIZATORS, PIGMENTS… THE PLASTIFICATION PROCESS WILL USED GOOD CONCEPTION AND FABRICATION PRACTICES OF METALLIC SUPPORTS FOR OPTIMIZING THEIR PERFORMANCES. THIS IS WHY, STS WILL CHECK THE FEASIBILITY OF EACH SUPPORT TO BE PLASTIFIED BY USING CRITERIA OF ELIGIBILITY.
H
l
L
SETTING UP
The STS good practices allow to offer
longer-lasting of coated hardware
thanks to an in line treatment of
plastisol using vaccum technology for
insuring homogeneity and
watertightness of coating.
Speed of dipping and then
homogeneous thickness are key
parameters of best practices of
manufacturing.
They will impact on the useful life
of coating and metallic hardware.
. Nature of material,
. Dimensions of parts to be coated and compatibility with dipping tanks and ovens
are key criteria of eligibily for appropriated coating performances.
Performances of coating on metallic substrates are achieved according to specific manufacturing procedures. We point out the following precautions :
-Enough thermal mass ; -hollowed shape and
sharped angles not recommended because plastisol is exposed to indent phenomenon during the solidification phase.
-We use to mask some areas when necessary.
-No grease on metallic supports which will be sand-blasted before adherence primer application.
Telephone : 33 (0)1 34 69 95 10 – Fax : 33 (0)1 34 69 67 90 – email : contact@sts-eco-planete-industrie.fr
top related