7,500 litre un portable t50 tank - cts-my.com 7500l un t50.pdf · • design code: asme viii div 1...
Post on 24-Jun-2020
2 Views
Preview:
TRANSCRIPT
Servicing - Manufacturing - Engineering
Cryogenic Tank Services (M) Sdn. Bhd.(438902-V)Lot 1310, Jalan Batu Arang, Sungai Bakau,48000 Rawang, Selangor Darul Ehsan,Malaysia.
t: +603-6092 0093fax: +603-6092 3093e: khc@cts-my.comw: www.cts-my.com
7,500 LITRE UN PORTABLE T50 TANK
7,500 LITRE UN PORTABLE T50 TANK
Specification
• Tank Type: 10ft ISO Universal Full Frame Offshore Tank.
• Capacity: 7,500 litres Nominal.• TARE: 4,250kg Nominal.• M.G.W: 12,000kg. • Stored Products: General purpose liquids.• MAWP: 20.4 bar.• Test Pressure: 26.5 bar.• Ambient temp: -20oC to + 55oC.• Type Approvals: UN Portable Tank T50 (incorporating
ADR and IMDG), UIC, TIR, CSC, TPED. The complete container will meet the requirements of ISO 1496/3, EN 12079 and DNV 2.7-1 offshore regs.
• Classification: Lloyds Register Industrial Division.
• Design Code: ASME VIII Div 1 where applicable.• Design temp: -40oC to + 55oC.• Material: EN 10088 P355NL1.
• Internal Finish: De-scaled and Nitrogen-purged.
Vessel
• Type: ISO 668 IDX - 10’ Long x 8’ Wide x 8’ High.• Material: BS4360 Grade 50D or equivalent RHS , dimension
ally to meet ISO 668 and 1161 requirements. Load transfer zones fitted.
• Walkways: 400mm wide ‘Q’ grating walkway sections fitted on each longitudinal side complete with transverse sections to front and rear of manlid spill tray.
• Ladder: Ladder fitted to rear end of tank container frame complete with grab handle on end frame. Rungs fitted with Scotgrip, attached with stainless steel rivets to rungs.
• Earthing: One stainless steel earth spade fitted to tank frame adjacent to the outlet, and one on opposite side of frame.
• Joining Plates: Each Tank can be fitted with plates for bolting 2 tanks together for transportation empty condition as a standard 20ft ISO unit.
• Lifting Lugs: Top of framework fitted with 4-off lifting lugs suitable for use with 8.5t bow shackles. Pin dia. 28mm.
• Sling assembly: Tank supplied with suitable offshore lifting slings.• Fork Pockets: 1-off set of fork pockets 120mm x 400mm.• Lashing lugs: 4-off D-ring lashing lugs welded to frame and
painted yellow.• N.D.E: Inspection of structural framework welds in accordance
with DNV requirements.
FrameGeneral
• Safety Relief valve: 1 x 3” Fort Vale Gas relief valve set at 20.4 bar.
• Manlid: 500mm dia. Flat-bolted manlid.• Gas Line: 2” Fort Vale internal safety valve with 2”
ball valve, c/w 1.25” ACME connector. • Liquid Line: 2” Fort Vale internal safety valve with 2”
ball valve, c/w 1.25” ACME connector. • Spill Trays: Spill tray around manlid and relief valve.
Surround condtructed of steel complete with stub pipes.
• Document Holder: Plastic document holder fitted to rear
end frame.
Components
External Corrosion Protection
• Data Plates: Consolidated Data Plate, customs plate, calibration decal. Plate for attaching data plates welded to frame.
• Statutory Decals: Supplied and fitted.• Serial numbers: Serial numbers welded to tank frame in
60mm-high letters.
Marking
• Shotblast: SA 2.5 to Framework.• Carbon Steel and framework: One coat Leighs C425 primer to 150microns DFT.
One coat Leighs C750 to 50 microns DFT. Colour TBA
top related