8,91 kn 1600 kg 75 kg - y-proximité...1600 kg 75 kg 8,91 kn 10/97 - 11/03 98 - 96 - 06/03 w/018...
Post on 25-Jan-2021
1 Views
Preview:
TRANSCRIPT
-
Cat. No.
e20
1600 Kg 75 Kg8,91 kN
10/97 - 11/0398 -96 - 06/03
W/018
VOLKSWAGEN GOLF IV htb.VOLKSWAGEN BORA SEDANAUDI A3
e20 55R 01 0802
-
���
����
0Km 1000Km
Moment skręcający dla śrub i nakrętek (8.8) Torgue settings for nuts and bolts (8.8)
M8
M10
M12
M14
M16
25Nm
55Nm
85Nm
135Nm
195Nm
-
x1
B
C
D
E
2
2
4
4
4
M12
∅30x∅10.2x3
M12
M10
x1
x1
x1
x1
M12 4
A
Śruba M12x70-8.8 ; Bolt
Nakrętka M12 ; NutPodkł. spręż.12,2 ; Spring WasherPodkł. okr. 13 ; Plain Washer
Śruba M10x40-8.8 ; BoltPodkł. spręż.10,2 ; Spring WasherPodkł. okr. pow. 10,5 ; Plain Washer
Śruba M12x35-8.8 ; BoltPodkł. spręż.12,2 ; Spring WasherPodkł. okr. 13 ; Plain Washer
A
B
C
D
Pkt. 1
Pkt. 1 Pkt. 2
Pkt. 2 Pkt. 3Pkt. 3
Pkt. 4Pkt. 4
E
x1
M12x70
M12x35
M10x40
2
4
-
Śrub
a M12
x70-
8.8 ;
Bolt
Nakrę
tka M
12 ; N
utPo
dkł. s
pręż
.12,2
; Spr
ing W
ashe
rPo
dkł. o
kr. 13
; Plai
n Was
her
Śrub
a M10
x40-
8.8 ;
Bolt
Podk
ł. spr
ęż.10
,2 ; S
pring
Was
her
Podk
ł. okr.
pow.
10,5
; Plai
n Was
her
Śrub
a M12
x35-
8.8 ;
Bolt
Podk
ł. spr
ęż.12
,2 ; S
pring
Was
her
Podk
ł. okr.
13 ; P
lain W
ashe
r
A
B
C
D
Pkt.
1
Pkt.
1Pk
t. 2
Pkt.
2Pk
t. 3
Pkt.
3
Pkt.
4Pk
t. 4
Nr ka
talog
owy
W/0
18M
arka
od 1
0/97
-11/
03Vo
lksw
agen
Gol
f IV
96-1
11 K
owie
sy, C
hojn
ata
23 A
tel.
+48
46 8
31 7
3 31
-
• Odkręcić tylne lampy, zderzak, belkę zderzeniową (nie będzie już zamontowana), plastikową osłonę tylnego pasa w bagażniku.• Odkleić taśmy zaślepiające technologiczne otwory montażowe zaczepu na bocznych, zewnętrznych płaszczyznach podłużnic.• Włożyć elementy zaczepu C i D w podłużnice i lekko przykręcić (pkt 1) śrubami M10x40 8.8.• Do elementów C i D przykręcić lekko belkę zaczepu A (pkt 2 i 3) śrubami M12x35 8.8.• Dokręcić śruby z momentem wg tabeli.• Podłączyć instalację elektryczną.• Wyciąć w zderzaku przestrzeń na łapki.• Zamontować zderzak, tylne lampy i plastikową osłonę tylnego pasa.• Przykręcić kulę i blachę gniazda elektrycznego śrubami M12x70 8.8.
• Unscrew the rear lights, bumper, bumper bar (it will not be used any more), the plastic shield of the rear belt in the boot.• The technological tow bar �tting holes on the side, external �ats of the metal clamps make permeable (the holes are sticked by band).• Insert the elements C and D in the metal clamps and screw slightly (point 1) with bolts M10x40 8.8.• Screw slightly the main bar A to the elements C and D with bolts M12x35 8.8 (point 2 and 3).• Tighten all the bolts according to the torque setting- see the table.• Connect the electric wires.• Cut out the fragment in the bumper to place the handles of the ball.• Assemble the bumper, rear lights and plastic shield of the rear belt.• Fix the ball and electric plate with bolts M12x70 8.8.
-
1
2 22
3
2x M10x40
2x M10
2x ∅30x∅10.2x3
-
2x M10x40
2x M10
2x ∅30x10,5x3
6040
2x M12x70
2x M12
2x M12
2x M12
2x M12x35
2x M12
2x M12
top related