api rp 2a 21st 2007 - joint only
Post on 02-Jun-2018
292 Views
Preview:
TRANSCRIPT
-
8/10/2019 API RP 2A 21st 2007 - Joint Only
1/20
Comparisons on API
RP 2A - WSD 21st edition2000 Publication vs. 2007 Publication
Strength of Tubular Joints
12/7/2014 1Engineering Dynamics, Inc
All right reserved. No part of this document may be reproduced in any form withoutprior written permission of Engineering Dynamics, Inc.
-
8/10/2019 API RP 2A 21st 2007 - Joint Only
2/20
OverviewThe old (we will call it API 2000):API RP 2A - WSD 21st edition 2000PublicationRecommended Practice forPlanning, Designing and
Constructing Fixed OffshorePlatforms Working Stress Design
Upstream Segment
API RECOMMENDED PRACTICE 2A-WSD
(RP 2A-WSD)TWENTY-FIRST EDITION, DECEMEBER 2000
And the latest (we will call it API 2007):API RP 2A - WSD 21st edition 2007Publication (API 2007)Recommended Practice for Planning,Designing and Constructing Fixed Offshore
Platforms Working Stress Design
Upstream Segment
API RECOMMENDED PRACTICE 2A-WSD (RP 2A-WSD)
TWENTY-FIRST EDITION, DECEMEBER 2000ERRATA AND SUPPLEMENT 1, DECEMBER 2002ERRATA AND SUPPLEMENT 2, SEMPTEMBER 2005ERRATA AND SUPPLEMENT 3, AUGUST 2007
12/7/2014 2Engineering Dynamics, Inc
-
8/10/2019 API RP 2A 21st 2007 - Joint Only
3/20
Conclusions1. The latest. The new API RP 2A - WSD 21 st edition with Errata andSupplement 1, 2 an 3 has made wide ranging changes on tubularconnections, fatigue and foundations over the 2000 publication. The newcode should be used if the API RP 2A WSD 21 st edition is selected as designcode.
2. One stop solution, no interface handling. Based on 35+ yearsexperience in supplying offshore structure software system, EDI is theleading software company with integrated graphics modeling, pre-processing, solving and graphics post-processing capabilities.3. Demand the best . Fully implemented in post processor, joint can and
fatigue programs in SACS 5.3 release, the new API RP 2A WSD 21st
editionwith Errata and Supplement 1, 2 and 3 is now an essential part in the mostcomprehensive offshore package in the world.
12/7/2014 3Engineering Dynamics, Inc
-
8/10/2019 API RP 2A 21st 2007 - Joint Only
4/20
Strength of Tubular Joints
Code ContentsAPI 20004 Connections
4.1 Connections of Tension and CompressionMembers4.2 Restraint and Shrinkage4.3 Tubular Joints
API 20074 Strength of Tubular Joints
4.1 Application4.2 Design Considerations4.3 Simple Joints4.4 Overlapping Joints4.5 Grouted Joints4.6 Internally Ring-stiffened Joints4.7 Cast Joints4.8 Other Circular Joint Types4.9 Damaged Joints4.10 Non-circular Joints
12/7/2014 4Engineering Dynamics, Inc
-
8/10/2019 API RP 2A 21st 2007 - Joint Only
5/20
Fact:Last major update to joint strength provisionswas 14 th edition. The guidance essentiallyremained unchanged for all editions up to21 st .
Strength of Tubular JointsBackground
12/7/2014 5Engineering Dynamics, Inc
-
8/10/2019 API RP 2A 21st 2007 - Joint Only
6/20
Fact:Much further knowledge, including both experimentaldata and numerical studies, has been gained on thebehavior of joints since 14 th edition issued. Over theperiod 1994 to 1996 MSL engineering, under theauspices of a joint industry project, undertook anupdate to the tubular joint database and guidance. This
work had more recent studies, notably by API/EWI andthe University of Illinois, have formed the basis of thetubular joint strength provisions of ISO.
Strength of Tubular JointsBackground
12/7/2014 6Engineering Dynamics, Inc
-
8/10/2019 API RP 2A 21st 2007 - Joint Only
7/20
Fact:The ISO drafting committee took, as a starting
point for drafting, the relevant provisions fromAPI RP 2A LRFD 1st edition (similar to API RP 2AWSD 20 th edition) because ISO is in LRFD format.For the purpose of the supplement to the 21 st edition of API RP 2A, the draft ISO provisions, inturn, have been used as a starting basis.
Strength of Tubular JointsBackground
12/7/2014 7Engineering Dynamics, Inc
-
8/10/2019 API RP 2A 21st 2007 - Joint Only
8/20
Strength of Tubular JointsMajor Update
API 2007
12/7/2014 Engineering Dynamics, Inc 8
Minimum Capacity Check Revised
API 2000
In which Pa is calculated as follows with FS = 1.0
In SACS program the following equation is used:
-
8/10/2019 API RP 2A 21st 2007 - Joint Only
9/20
API 2000
SF = 1.7 Corresponded to an LRFDresistance factor of 0.95.
Strength of Tubular JointsMajor Update
Safety Factor Recalibrated
API 2007
SF = 1.6 Corresponded to an LRFDresistance factor of 1.0
12/7/2014 9Engineering Dynamics, Inc
-
8/10/2019 API RP 2A 21st 2007 - Joint Only
10/20
API 2000
Section 4.1Fyc the yield strength of the chord
member at the joint (or 2/3 of thetensile strength if less)
Strength of Tubular JointsMajor Update
The 2/3 limits on tensile strength relaxed
API 2007
Section 4.2.1The value of yield stress for the chord,in the calculation of joint capacity,should be limited to 0.8 times thetensile strength of the chord formaterials with a yield stress of 72 ksi(500 MPa) or less.
12/7/2014 10Engineering Dynamics, Inc
-
8/10/2019 API RP 2A 21st 2007 - Joint Only
11/20
API 2000
Strength of Tubular JointsMajor Update
Additional guidance on detailing practice
12/7/2014 11Engineering Dynamics, Inc
-
8/10/2019 API RP 2A 21st 2007 - Joint Only
12/20
Strength of Tubular JointsMajor Update
Additional guidance on detailing practice - continued
API 200712/7/2014 12Engineering Dynamics, Inc
-
8/10/2019 API RP 2A 21st 2007 - Joint Only
13/20
API 2000The adequacy of the joint may bedetermined on the basis of (a)punching shear or (b) nominal loads inthe brace.
Strength of Tubular JointsMajor Update
Punching shear approach removed
API 2007The joint interaction ratio, IR, for axialloads and/or bending moments in thebrace should be calculated using thefollowing expression,
12/7/2014 13Engineering Dynamics, Inc
-
8/10/2019 API RP 2A 21st 2007 - Joint Only
14/20
API 2000
Strength of Tubular JointsMajor Update
New Strength factor Q u formulations
API 2007
12/7/2014 14Engineering Dynamics, Inc
-
8/10/2019 API RP 2A 21st 2007 - Joint Only
15/20
API 2000
Strength of Tubular JointsMajor Update
New chord load factor Q f formulations
API 2007
12/7/2014 15Engineering Dynamics, Inc
-
8/10/2019 API RP 2A 21st 2007 - Joint Only
16/20
API 2000N/A
Strength of Tubular JointsMajor Update
Strength for axially loaded Y and X joints with short can lengths reduced
API 2007For simple, axially loaded Y and X joints where athickened joint can is specified, the joint
allowable capacity may be calculated as follows,
12/7/2014 16Engineering Dynamics, Inc
-
8/10/2019 API RP 2A 21st 2007 - Joint Only
17/20
-
8/10/2019 API RP 2A 21st 2007 - Joint Only
18/20
Simple T joint:
Brace 3-4: 16x0.375 5.0ftChord 1-3 & 3-2: 24x0.375 8.25ft
Can: 24x0.625 1.75ft
All Fy = 36 ksiLoad at brace joint 4:
Fx = 10.0 kipFy = 7.5 kipFz = -50.0 kip
Load at connecting joint 3:Fx = -400.0 kip
Fy = 50.0 kip
Strength of Tubular JointsExample
Member Length shown in ft
12/7/2014 18Engineering Dynamics, Inc
-
8/10/2019 API RP 2A 21st 2007 - Joint Only
19/20
API 2000 Punching shear joint check with final unity check ratio = 0.974
* * J O I N T C A N D E T A I L R E P O R T * *(JOINT ORDER)
CHORD * ACTING STRESSES * *** PUNCHING SHEAR ***COMMON CHORD BRACE ****** CHORD ***** JOINT GAP *** BRACE ** BRACE LOAD *CHORD** BRACE * ALLOWABLE STRESSES UNITY
JOINT JOINT JOINT O.D. WT FY TYPE O.D. WT ANGLE CASE SRSS FA OPB IPB FA OPB IPB CHECK(IN) (IN) (KSI) (IN) (IN) (IN) (DEG) (KSI) (KSI) (KSI) (KSI) (KSI) (KSI) (KSI)
3 1 4 24.00 0.625 36.0 T 16.00 0.375 90.00 1 11.51 -1.63 3.84 5.12 3.66 6.65 11.15 0.974
Strength of Tubular JointsExample Results Compared
API 2007 Brace loads interaction check with final unity check ratio = 1.168
* * J O I N T C A N D E T A I L R E P O R T * *(UNITY CHECK ORDER)
EFFT. CHORD * ACTING STRESSES * *** PUNCHING SHEAR ***
COMM CHRD BRCE ****** CHORD **** CHORD JNT GAP *** BRACE ** BRACE LOAD *CHORD** BRACE * ALLOWABLE STRESSES UNITYJNT JNT JNT O.D. WT FY LNGTH TYP O.D. WT ANGLE CASE STRESS FA OPB IPB FA OPB IPB CHECK
IN IN KSI FT IN IN IN DEG KSI KSI KSI KSI KSI KSI KSI
3 1 4 24.00 0.625 36.0 3.5 T 16.00 0.375 90.00 1 -11.51 -2.72 6.40 8.54 7 .20 10.16 21.30 1.168
Joint Can Length
12/7/2014 19Engineering Dynamics, Inc
-
8/10/2019 API RP 2A 21st 2007 - Joint Only
20/20
Figure 2.3.1-1 Procedure for Calculation of Wave Plus Current Forces for Static Analysis
12/7/2014 Engineering Dynamics, Inc 20
top related