biofeedback using bpm and hrv values

Spooky2

Our Users & Team

Biofeedback Using BPM and HRV Values

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:echolee@cleanenergy-npt.comor service@spooky2.com

When we use a biofeedback scan, we are asking the body to tell us

what it needs. The body knows well and does not lie. However, when

we try to force the body to go in a direction we want, well this just

does not usually work out well.

While we can isolate the results to known modalities, one would be

hard pressed to scan with only one result in mind.

You can't really tell your body to ignore all the things you maybe don't

even know about, in favor of that one frequency that will make your left

toe stop itching.

Lots of times things get complicated by the fact we try to treat based

on symptoms and not the source. When doing a biofeedback scan, the

body knows the source and will respond accordingly.

With that in mind, one should use the frequencies as is in a treatment. I often see that

someone believes they need to use the information to select frequency sets to run. The

best frequency set was already given.

With that said, we can filter the results the body returns into specific modalities.

When we scan for Max BPM, we are only finding frequencies that elicit a maximum

stress event. Therefore, all results will be of a killing modality.

When we scan for Min BPM, we are only finding frequencies that elicit a calming event,

therefore of a healing modality.

When we scan using Max HRV, we are finding frequencies that elicit the maximum

stress or calming event, as this is an absolute function. This means all frequency hits

returns can be for either modality, and there is no way to know for which.

When we scan using Min HRV, we are looking for frequencies that elicit the least

change to our body. Again this is an absolute function -- can find both types of

frequencies. Where this may be useful is if you are looking for frequencies for instance

that help maintain a steady state during meditation.

As for the frequency range.

76k to 152k is an octal range. 152 is twice that of 76. It is like scanning one octave of

the piano from Middle C to High C.

Every frequency is covered by harmonic resonance when you scan a range like this.

The low C, the lowest A, and the highest G on the piano are also tickled by resonance.

So the entire range can not be defined as a killing only range. While we do not have

all frequencies mapped out to make a claim like this on any range, when dealing with

an octal range (ending frequency is twice the starting frequency), you essentially are

covering all frequencies and thus the entire gambit.

The frequency is what does the work. Not the settings, not the preset.

So if you use the results from a Max BPM scan with the Healing preset, which uses a square wave, it will still kill stuff.

If you ran it via the Killing preset, you would just aid the frequencies ability to kill by using more appropriate settings.

You can not turn a frequency from one modality to another by switching presets or waveforms.

biofeedback using bpm and hrv values

Health & Medicine

stress „messen“ - gesundheitspsychologie.phil.fau.de ·...

efeito de uma prova de triathlon na variabilidade da...

capitulo 1 guia practica biofeedback

hubungan di antara prestasi perniagaan dengan profil hrv...

biofeedback bogota

resonant frequency heart rate biofeedback

hrv. kult.doc

79660815 makalah biofeedback

hrv a_list_sa_odgovorima.pdf

biofeedback 1feb a jk

a anorectal y biofeedback

eeg biofeedback

biorretroalimentación (biofeedback)

eeg biofeedback

biofeedback (bfb)

opuscule dédié au modello hrv 140 touch hrv 140 ... hrv...

neurofeedback e biofeedback - airnp

keberkesanan kaedah latihan biofeedback emwave

live biofeedback in electronic markets

fÖrstoppningˆrstoppning_simren_handouts.pdf– anorektal...