catalogo 2009 rele
Post on 16-Jul-2016
44 Views
Preview:
TRANSCRIPT
Electromechanicaland solid-state relaysZelio RelayCatalogueApril 2009
1
Reduce the size of yourenclosures and, at thesame time, increasemachine reliability
Make the most of your energy
ContentsPresentationChoose compactness with Zelio Relay RSL ....................................................................... 2-3Choose long life and silent operation with Zelio Relay SSR ................................................. 4-5Electromechanical and solid-state relays panorama ........................................................... 6-7
Technical characteristicsZelio Relay RSL ................................................................................................................................. 8-15Zelio Relay RSB, RXM, RUM, RPM ............................................................................................ 16-49Zelio Relay ABR, ABS .................................................................................................................... 50-69Zelio Relay SSR .............................................................................................................................. 70-77
The new Zelio Relay itemsElectromechanical relays RSLOnly 6 mm wide, thus saving considerable spacein your enclosures
Solid-state relays SSRUnlimited service life provided by electronic technology
6 mm wide
Unlimited service life
2
Choose compactnesswith Zelio Relay RSL
Only 6 mmwide, thus reducing the sizeof your enclosures
> A solution forany application
A complete offer
> An offer with maximum flexibility, comprising:• complete products: a single reference for a relaymounted on a socket,
• products for customer assembly: select the relayand associated socket according to your application.> Wide choice of sockets available covering a rangeof voltages from 12 to 230 V.
An offer that meets the mostdemanding standards
• Conformity with the European RoHS(Restriction of Hazardous Substances) directive.• Conformity to international standardsIEC/EN 61810-1, UL508, CSA C22.2 N°14, GOST.
100% RoHSSchneider Electric commits itself toreducing the environmental impactof its products
3
> Reliability in any situation
Protection integrated in the socket
The assurance of reliable protection of the relayirrespective of the supply voltage used.
LED indicator
Power on and relay status LED indicator.
«Standard» and «low level»version relays
For high breaking capacity or low levelcurrent application requirements.
> Simplicity of installationand cabling
Simple maintaining of relay in socketand its release/removalUsing locking/unlocking lever.
Simplification of cablingCommoning link available as accessory.
Simple mounting on DIN rail
Choice of 2 connection techniquesSuitable for the majority of your applications.
Up to 6Abreaking capacity
Spring terminalScrew connector
44
Choose long life andsilent operation withZelio Relay SSR
> Heat exchange guaranteedThe new solid-state relays SSR with SCR (SemiconductorControlled Rectifier) outputs offer you two alternatives:
SSRD rangeDirectly mounted with heat sink to provide heat exchange,they are easily mounted by clipping directly onto DIN rail andcan also be panel mounted.
SSRP rangePanel mounted, either on their own or combined witha heat sink for applications requiring considerable heat exchange.
SSRP relay mounted on heat sink withthermal interface
SSRAH1
ASSEMBLED IN MEXICO
0812
5
> Distinctive indicationA green LED on the front face of the products provides instantindication of the relay input status.
> High performanceHigh breaking capacities• From 10 to 125 A for relays SSRP• From 10 to 45 A for relays SSRD
Wide supply voltage range• From 3 to 32 VDC and 90 to 280 VAC
Outputs suited to applications• From 24 to 280 VAC and 48 to 530/660 VAC
Extreme compactness• Only 22.5 mm and up to 45.5 mm wide
Unlimited service life• No preventive maintenance, relays SSR have aunlimited service life
Silence of electronic technology• Complete silence when switching
Insensitive to vibration• Even in the event of excessive vibration, the relaywill not change state
> Conformity tointernational standards
100%RoHS
Schneider Electric commits
itself to reducing the environmental
impact of its products
Unlimitedservice lifedue to electronic relaytechnology
Completesilence whenswitchingproviding suitability forbuilding and hospitalapplications
High switchingfrequencyparticularly on packagingand textile machines
Panorama Zelio Relay
Number CO contacts
Current
References
1 CO 1 or 2 CO 1 or 2 CO 2, 3 or 4 CO 1, 2, 3 or 4 CO
6 A 8-12-16 A 5-12 A 6-10-12 A 10 A 15A
RSL RSB ABR RXM RUM RPM
8 to 15 16 to 21 50 to 69 22 to 29 30 to 39 40 to 49Pages
Electromechanical relays
Plugs into socket On DIN rail Plugs into socketMounting
1 NO
3 A
ABS
50 to 69 70 to 77 70 to 77
Solid-state relays
2, 3 or 4 CO
On DIN rail On DIN rail
1 NO
10 ...45 A 10 ...125 A
1 NO
On panel
SSRD SSRP
Electromechanical relay advantages
• Wide choice of number of contacts (up to 4)• Easy installation and maintenance:
Plug-in relay for socket mounting (universal format)Contact status mechanical indicator and “Relay On” LED indicatorLockable “Test” button for testing relay operation
• Electrically separated inputs and outputs, allowing different voltages
Number CO contacts
Current
References
1 CO 1 or 2 CO 1 or 2 CO 2, 3 or 4 CO 1, 2, 3 or 4 CO
6 A 8-12-16 A 5-12 A 6-10-12 A 10 A 15A
RSL RSB ABR RXM RUM RPM
8 to 15 16 to 21 50 to 69 22 to 29 30 to 39 40 to 49Pages
Electromechanical relays
Plugs into socket On DIN rail Plugs into socketMounting
1 NO
3 A
ABS
50 to 69 70 to 77 70 to 77
Solid-state relays
2, 3 or 4 CO
On DIN rail On DIN rail
1 NO
10 ...45 A 10 ...125 A
1 NO
On panel
SSRD SSRP
Solid-state relay (SSR) advantages
• Unlimited service life• Wide supply voltage range and high breaking current(up to 125 A), suited to packaging and textile machines• “Relay On” LED indicator• Completely silent switching, providing suitability forbuilding and hospital applications• Insensitive to vibration
2
1
3
4
5
6
7
8
9
10
Application Plug-in relays
Number and type of contacts / conventional thermal current (Ith on N/O contact)
1 C/O / 6 A
Control voltage range c 12…60 V
Contact type Standard YesLow level Yes
Type of pins Flat (PCB type, reinforced)
Operating voltage Up to a 400 V / c 300 V
Durability(operating cycles)
Electrical, resistive load 60 000Mechanical, no-load 10 000 000
Relay type RSL 1pB4pD
Pages 14
Conventional thermal current (Ith) 6 A 6 A
Connection Screw connector Spring terminals
LED Yes Yes
Protection circuit Yes Yes
Accessories Socket identification legend Yes YesBus jumper Yes YesPartition plate Yes Yes
Socket type RSL ZVpp RSL ZRpp
Pages 14 14
Slim interface relays, pre-assembled RSL 1PVpp RSL 1PRpp
Pages 14 14
Selection guide Zelio Relay - plug-in relaysRSL slim interface relays
PF0
9021
1P
F090
209
PF0
9020
6
2
1
3
4
5
6
7
8
9
10
99
Application Plug-in relays
Number and type of contacts / conventional thermal current (Ith on N/O contact)
1 C/O / 6 A
Control voltage range c 12…60 V
Contact type Standard YesLow level Yes
Type of pins Flat (PCB type, reinforced)
Operating voltage Up to a 400 V / c 300 V
Durability(operating cycles)
Electrical, resistive load 60 000Mechanical, no-load 10 000 000
Relay type RSL 1pB4pD
Pages 14
Conventional thermal current (Ith) 6 A 6 A
Connection Screw connector Spring terminals
LED Yes Yes
Protection circuit Yes Yes
Accessories Socket identification legend Yes YesBus jumper Yes YesPartition plate Yes Yes
Socket type RSL ZVpp RSL ZRpp
Pages 14 14
Slim interface relays, pre-assembled RSL 1PVpp RSL 1PRpp
Pages 14 14
PF0
9021
0P
F090
207
2
1
3
4
5
6
7
8
9
10
1010
Presentation Zelio Relay - plug-in relaysRSL slim interface relays
PresentationRSL slim interface relays offer the advantages of compact size and modular design: their slim width (6 mm) saves space when mounting on a 5 rail at the back of an enclosure.
RSL relays are available in two versions:pre-assembled range: a single reference comprising a relay mounted on its
socket. The socket includes a protection circuit (against reverse polarity and surge) and
an LED indicator as standard.Two types of connector are available for wire connection: screw connectors or
spring terminals. This pre-assembled solution covers a wide range of operating voltages from 12 to
230 V.range for customer assembly: The relay (standard or low level) and the socket are selected, as required,
according to the operating voltage of the application. For maintenance: an RSL slim relay can be replaced without any need to
disconnect the socket wiring.
b
v
v
v
bv
v
DescriptionRSL slim interface relays, pre-assembled
6 A relay (standard or low level) with 1 C/O contact.Lever for retaining, or easy withdrawal of the relay from its socket. Sockets: wire connection by screw connector or by spring terminals.All sockets have a built-in protection circuit and LED indicator.
1 2 3 4
RSL slim interface relay
Five flat, reinforced pins (PCB type).1
Sockets for RSL slim interface relays
Five female contacts for the relay pins.Retaining lever with marker label.Wire connection by screw connector or by spring terminals.Protection circuit and LED indicator (built into the socket)Locating slot for mounting on 5 rail.
1 2 3 4 5
Presentation : page 10
Characteristics : page 11
References : page 14
Dimensions, schemes : page 15
1
2
3
4
PF0
9021
3
1
PF0
9020
1
24
5
3
PF0
9021
2
2
1
3
4
5
6
7
8
9
10
1111
Characteristics Zelio Relay - plug-in relaysRSL slim interface relays
General characteristicsConforming to standards
IEC 6110-1, UL 50, CSA C22-2 No. 14
Product certifications
UL, CSA, GOST
Ambient air temperature around the device
Storage
°C - 40… + 5
Operation
°C - 40… + 55
Vibration resistanceconforming to IEC/EN 6006-2-6
In operation
10 gn
Not operating
5 gn
Degree of protection Conforming to IEC/EN 60529
IP 40 (Relays)IP 20 (Sockets)
Shock resistanceconforming to IEC/EN 6006-2-27
Opening
10 gn
Closing
5 gn
Protection category
RT III
Mounting position
Any
Insulation characteristicsRated insulation voltage (Ui)
V 250 (IEC)
Rated impulse withstand voltage (Uimp)
kV 6
Dielectric strength(rms voltage)
Between coil and contact
a V 4000
Between contacts
a V 1000
2
1
3
4
5
6
7
8
9
10
1212
Characteristics (continued) Zelio Relay - plug-in relaysRSL slim interface relays
Contact characteristicsRelay type RSL1ABppp RSL1GBppp
Number and type of contacts 1 C/O 1 C/O low level
Contact materials AgSnO2 AgSnO2 - gold plated
Conventional thermal current (Ith)
For ambient temperature y 55 °C
A 6 6
Rated operational current in utilisation categories AC-1 and DC-1
Conforming to IEC N/C A 6 6N/O A 6 6
Conforming to UL A 6 6
Switching current Minimum mA 100 1 (at 50 mW)
Switching voltage Rated a V 250 250Maximum V a 400, c 300 a 250, c 300 Minimum V 12 1 (at 50 mW)
Nominal load (resistive) A 6 / a 250 V, 0.5 mm
Switching capacity Maximum a VA 1500c W 1…150 (depending on the voltage)
Minimum mW 120 50
Maximum operating rateIn operating cycles
No-load 72 000Under load 360
Mechanical durability In millions of operating cycles 10
Electrical durabilityIn millions of operating cycles
Resistive load See curves below
Inductive load 0.05 (N/O contact /250 V, 3 A, AC-15)
Maximum switching capacity on c load Electrical durability
Current c
Volta
ge c
0,1 0,2 0,5 1 10 202 510
20
30
5040
100
200
300
Resistive load
Cyc
les
Switching current (A)
104
105
106
107
0 1 2 3 4 5 6 7 8
Resistive load a 250V
AgSnO2
Coil characteristicsAverage consumption c W 0.17
Drop-out voltage threshold c u 0.05 UcOperating time(response time)
Between coil energisation and making of the On-delay contact
c ms 12 max
Between coil de-energisation and making of the Off-delay contact
c ms 5 max
Control circuit voltage Uc V 12 24 48 60Relay control voltage codes JD BD ED ND
DC supply Average resistance at 23 °C ± 10% Ω 4 3390 10 600 20 500
Operating voltage limits Min. V .4 16. 33.6 42Max. V 16. 33.6 67.2 4
Presentation : page 10
Characteristics : page 11
References : page 14
Dimensions, schemes : page 15
2
1
3
4
5
6
7
8
9
10
1313
Socket characteristicsSocket type RSL ZVpp RSL ZRpp
Relay types used RSL 1pppp RSL 1pppp
Conforming to standards IEC 6194, UL 50, CSA C22-2 No. 14Product certifications UL, CSA, GOSTContact terminal arrangement Separate SeparateWire connection method Screw connector Spring terminalsWidth mm 6.2 6.2
Electrical characteristicsConventional thermal current (Ith) A 6Maximum operating voltage V 300
Insulation characteristicsBetween adjacent output contacts Vrms 2500Between input and output contacts Vrms 2500Between contacts and 5 rail Vrms 2500
General characteristicsAmbient air temperaturearound the device
Operation °C - 40…+ 70 / - 40…+ 55 for U > 0 VStorage °C - 40…+ 5
Degree of protection Conforming to IEC/EN 60529 IP 20Cabling Solid cable
without cable end1 conductor mm² 0.2…2.5 0.2…1.5
AWG 24…14 24…16 Flexible cable with cable end
1 conductor mm² 0.2…2.5 0.2…1.5AWG 24… 14 24…16
Screw size mm M 2.5Maximum tightening torque Nm 0.5 10 N…40 N (0.2 …1.5 mm²)
Mounting On 35 mm 5 railFixing on 5 rail By plastic compression spring
Terminal referencing IECLED indicator Yes (built-in)
Protection circuit Yes (built-in)Wire connection method Screw connector Spring terminal
Sockets operating voltageOperating voltage Tolerance Control circuit voltage (relay)V V
Socket type RSLZVA1, RSLZRA1 c/a 12 + 20% / - 5% c 12
c/a 24 + 20% / - 10% c 24
RSLZVA2, RSLZRA2 c/a 4 + 20% / - 10% c 4
c/a 60 + 20% / - 10% c 60
RSLZVA3, RSLZRA3 c/a 110 + 15% / - 20% c 60
RSLZVA4, RSLZRA4 c/a 230 + 15% / - 20% c 60
Characteristics (continued) Zelio Relay - plug-in relaysRSL slim interface relays
2
1
3
4
5
6
7
8
9
10
1414
References Zelio Relay - plug-in relaysRSL slim interface relays
Slim interface relays, pre-assembledRelays mounted on socket equipped with LED and protection circuitSold in lots of 101 C/O contact - Thermal current (Ith) 6AOperating voltage Control circuit voltage Socket type
Screw connector Spring terminalUnit reference Weight Unit reference Weight
V V kg kgc/a 12 c 12 RSL 1PVJU 0.031 RSL 1PRJU 0.029
c/a 24 c 24 RSL 1PVBU 0.031 RSL 1PRBU 0.029
c/a 48 c 48 RSL 1PVEU 0.031 RSL 1PREU 0.029
c/a 110 c 60 RSL 1PVFU 0.031 RSL 1PRFU 0.029
c/a 230 c 60 RSL 1PVPU 0.031 RSL 1PRPU 0.029
Slim interface relays for customer assembly: relay + socketRelays with flat, reinforced pins (PCB type)Sold in lots of 101 C/O contact - Thermal current (Ith) 6A
Standard Low levelControl circuit voltage Unit reference Weight Unit reference WeightV kg kg
c 12 RSL 1AB4JD 0.006 RSL 1GB4JD 0.006
c 24 RSL 1AB4BD 0.006 RSL 1GB4BD 0.006
c 48 RSL 1AB4ED 0.006 RSL 1GB4ED 0.006
c 60 RSL 1AB4ND 0.006 RSL 1GB4ND 0.006
Sockets equipped with LED and protection circuitSold in lots of 10
Socket typeScrew connector Spring terminal
Operating voltage For use with relays Unit reference Weight Unit reference WeightV kg kg
c/a 12 and c/a 24 RSL 1pB4JDRSL 1pB4BD
RSL ZVA1 0.025 RSL ZRA1 0.023
c/a 48 and c/a 60 RSL 1pB4EDRSL 1pB4ND
RSL ZVA2 0.025 RSL ZRA2 0.023
c/a 110 RSL 1pB4ND RSL ZVA3 0.025 RSL ZRA3 0.023
c/a 230
RSL 1pB4ND RSL ZVA4 0.025 RSL ZRA4 0.023
Accessories for socketsSold in lots of 10Description Compatibility Unit reference Weight
kgClip-in legends(sheet of 64 legends)
With all sockets RSL Z5 0.001
Bus jumper (20-pole jumper)
With all sockets RSL Z2 0.003
Partition plate With all sockets RSL Z3 0.001
Presentation : page 10
Characteristics : page 11
References : page 14
Dimensions, schemes : page 15
RSL 1pppp
PF0
9021
1
RSL ZVAp
PF0
9020
9
RSL 1PVpp
PF0
9020
6
RSL ZRAp
PF0
9021
0
RSL 1PRpp
PF0
9020
7
RSL Z2
RSL Z3
2
1
3
4
5
6
7
8
9
10
1515
Dimensions, schemes
Zelio Relay - plug-in relaysRSL slim interface relays
Slim interface relays, pre-assembledRSL 1PVpp (screw connector) RSL 1PRpp (spring terminals)
95
30,1
51,5 6,2 6,2
78,6
101
35,3
6,251,5 6,2
78,6
Relays for customer assemblyRSL 1pppp with flat, reinforced pins (PCB type)
(1): 5.04 mm
1,9
(1)
(1)
3,5±0,5
11,3
43,
78
15 max 5 max
2 m
ax
1 C/O contact
A1
A2
1211
14
Sockets equipped with LED and protection circuitRSL ZVpp (screw connector) RSL ZRpp (spring terminals)
95
30,1
51,5 6,2 6,2
78,6
101
35,3
6,251,5 6,2
78,6
Socket connections Example of RSL Z2 bus jumper mounting on sockets
RSL ZVpp (screw connector) RSL ZRpp (spring terminals) Side view
Protection circuit
14
11
A1
A2
12
12
11
14
A1
A2
Protection circuit
12
11
14
A1
A2
1411
A1
A212
(4)(2)
(1)(3)
(1) A1(2) A2(3) Bus jumper polarity A1(4) Bus jumper polarity A2
16
Selection guide
Universal relays Power relays
2 C/O / 10 A3 C/O / 10 A3 C/O / 3 A (low level)
2 C/O / 10 A3 C/O / 10 A
1 C/O / 15 A2 C/O / 15 A3 C/O / 15 A4 C/O / 15 A
24…230 V 24…230 V12…220 V 12…110 V 12…110 V
Cylindrical Flat (Faston type) Flat (Faston type)
Up to 250 V Up to 250 V
100 000 100 000 (3)5 000 000 10 000 000
Yes (depending on version) Yes (depending on version)Yes YesYes YesYes (depending on version) – –
RUM RPM
33 43
12 A 16 A
Mixed Separate Mixed
Connector Screw clamp terminals
Yes YesYes Yes (for 3 and 4-pole)Yes Yes (on socket RPZ F1)Yes Yes– Yes– Yes– Yes –
RUZ CpM RUZ SCpM RUZ SF3M RPZ Fp
34 34 44(3) 100 000 for RPM1 and RPM2; 60 000 for RPM3 and RPM4.
Application Plug-in relaysInterface relays Miniature relays
Number and type of contacts / conventional thermal current (Ith on N/O contact)
1 C/O / 16 A1 C/O / 12 A2 C/O / A
2 C/O / 12 A3 C/O / 10 A4 C/O / 6 A4 C/O / 3 A (low level)
Control circuit voltage a 24…240 V 24…240 Vc 6…110 V 12…220 V
Type of pins Flat (Faston type) Flat (Faston type)
Operational voltage Up to a 400 V / c 300 V Up to 250 V
Durability (operating cycles)
Electrical, resistive load 100 000 100 000Mechanical, no-load 30 000 000 10 000 000
Functions LED Yes (with protection modules) Yes (depending on version)Mechanical indicator – YesLockable test button – YesLow level contacts – Yes (depending on version)
Type reference RSB RXM
Pages 20 25 and 26
Conventional thermal current (Ith) 12 A (1) 10 A 12 A (2)
Contact terminal arrangements Separate Mixed Separate
Connection Connector Screw clamp terminals or connector
Connector
Accessories Protection modules Yes YesTimer module – –Maintaining clamps Yes YesSocket identification legend Yes Yes (except RXZ E2M114)Mounting adapters for 5 rail – YesMounting adapters with fixing lugs – YesBus jumper, 2-pole (Ith = 5 A) – – Yes
Associated socket types RSZ E1SppM RXZ E2Mppp RXZ E2Sppp
Pages 20 26 26(1) When using relay RSB 1A160pp with socket RSZ E1S48M, terminals must be linked.(2) Except for sockets RXZ E2S11pM: 10 A.
Zelio Relay - plug-in relays
1
2
3
4
5
6
7
8
9
10
17
Universal relays Power relays
2 C/O / 10 A3 C/O / 10 A3 C/O / 3 A (low level)
2 C/O / 10 A3 C/O / 10 A
1 C/O / 15 A2 C/O / 15 A3 C/O / 15 A4 C/O / 15 A
24…230 V 24…230 V12…220 V 12…110 V 12…110 V
Cylindrical Flat (Faston type) Flat (Faston type)
Up to 250 V Up to 250 V
100 000 100 000 (3)5 000 000 10 000 000
Yes (depending on version) Yes (depending on version)Yes YesYes YesYes (depending on version) – –
RUM RPM
33 43
12 A 16 A
Mixed Separate Mixed
Connector Screw clamp terminals
Yes YesYes Yes (for 3 and 4-pole)Yes Yes (on socket RPZ F1)Yes Yes– Yes– Yes– Yes –
RUZ CpM RUZ SCpM RUZ SF3M RPZ Fp
34 34 44(3) 100 000 for RPM1 and RPM2; 60 000 for RPM3 and RPM4.
Application Plug-in relaysInterface relays Miniature relays
Number and type of contacts / conventional thermal current (Ith on N/O contact)
1 C/O / 16 A1 C/O / 12 A2 C/O / A
2 C/O / 12 A3 C/O / 10 A4 C/O / 6 A4 C/O / 3 A (low level)
Control circuit voltage a 24…240 V 24…240 Vc 6…110 V 12…220 V
Type of pins Flat (Faston type) Flat (Faston type)
Operational voltage Up to a 400 V / c 300 V Up to 250 V
Durability (operating cycles)
Electrical, resistive load 100 000 100 000Mechanical, no-load 30 000 000 10 000 000
Functions LED Yes (with protection modules) Yes (depending on version)Mechanical indicator – YesLockable test button – YesLow level contacts – Yes (depending on version)
Type reference RSB RXM
Pages 20 25 and 26
Conventional thermal current (Ith) 12 A (1) 10 A 12 A (2)
Contact terminal arrangements Separate Mixed Separate
Connection Connector Screw clamp terminals or connector
Connector
Accessories Protection modules Yes YesTimer module – –Maintaining clamps Yes YesSocket identification legend Yes Yes (except RXZ E2M114)Mounting adapters for 5 rail – YesMounting adapters with fixing lugs – YesBus jumper, 2-pole (Ith = 5 A) – – Yes
Associated socket types RSZ E1SppM RXZ E2Mppp RXZ E2Sppp
Pages 20 26 26(1) When using relay RSB 1A160pp with socket RSZ E1S48M, terminals must be linked.(2) Except for sockets RXZ E2S11pM: 10 A.
1
2
3
4
5
6
7
8
9
10
1
Presentation of the rangeThe RSB interface relay range comprises: 1 12 A relays with 1 C/O contact , 16 A relays with 1 C/O contact and A relays with
2 C/O contacts.2 Sockets with separate contact terminals.3 Protection modules (diode, diode + LED, RC circuit or varistor + LED). All these
modules are common to all sockets.4 A plastic maintaining clamp for all sockets.5 Clip-in legends for the sockets.
Socket descriptionSockets with separate contact terminals (1)
1 Connection by connector. 2 Five or eight female contacts for the relay pins.3 A fixing hole for panel mounting.4 Location for protection modules.5 Locking components for plastic maintaining clamp.6 Locating slot for mounting on 5 rail.
(1) The inputs and outputs are separated from the relay supply.
General characteristics
Conforming to standards IEC/EN 6110-1, UL 50, CSA C22-2 n° 14Product certifications UL, CSAAmbient air temperature around the device
Storage °C - 40…+ 5Operation °C c - 40…+ 5, a - 40...+ 70
Vibration resistance Conforming to IEC/EN 6006-2-6 > 10 gn (10..150 Hz)Degree of protection Conforming to IEC/EN 60529 IP 40Shock resistanceconforming to IEC/EN 6006-2-27
Opening 5 gnClosing 10 gn
Protection category RT IMounting position AnyInsulation characteristics
Rated insulation voltage (Ui) Conforming to IEC/EN 60947 V 400Rated impulse withstand voltage (Uimp) kV 3.6 (1.2/50 µs)Dielectric strength(rms voltage)
Between coil and contact a V 5000Between poles a V 2500Between contacts a V 1000
Contact characteristicsRelay type RSB 1A120pp RSB 1A160pp RSB 2A080pp
Number and type of contacts 1 C/O 1 C/O 2 C/OContact materials AgNiConventional thermal current (Ith)
For ambient temperature y 40°C
A 12 16
Rated operational current in utilisation categories AC-1 and DC-1
Conforming to IEC “C” A 12 16 “O” A 6 4
Switching current Minimum mA 5Switching voltage Maximum V a 400, c 300
Minimum V 5Nominal load (resistive) A 12 / 250 a V 16 / 250 a V / 250 a V
A 12 / 2 c V 16 / 2 c V / 2 c VSwitching capacity Maximum a VA 3000 4000 2000
c W 336 44 224Minimum mW 300
Maximum operating rateIn operating cycles/hour
No-load 72 000Under load 600
Zelio Relay - plug-in relaysRSB interface relays
Presentation, characteristics
5351
1
2
35
6
4
Inputs
Outputs
Relay supply
5
4
1
5231
39
2
3
Presentation:page 1
References:page 20
Characteristics:page 19
Dimensions, schemes:page 21
1
2
3
4
5
6
7
8
9
10
19
Contact characteristics (continued)Relay type RSB 1A120pp RSB 1A160pp RSB 2A080pp
Mechanical durability In millions of operating cycles u 30Electrical durabilityIn millions of op. cycles
Resistive load 12 A - 250 V: u 0.1 16 A - 250 V: u 0.07 A - 250 V: u 0.1Inductive load See curves below
Electrical durability of contactsResistive load a
Reduction coefficient for inductive load a (depending on power factor cos j)
Maximum switching capacity on resistive load c
A RSB 2A080pp B RSB 1A160pp C RSB 1A120pp. Durability (inductive load) = durability (resistive load) x reduction coefficient.Coil characteristics
Average consumption c 0.45 W, a 0.75 VADrop-out voltage threshold ≥ c 0.1 Uc, ≥ a 0.15 UcOperating time(response time)
Between coil energisation and making of the On-delay contact
a ms 12c ms 9
Between coil de-energisation and making of the Off-delay contact
a ms 10c ms 4
Control circuit voltage Uc V 6 12 24 48 60 110 120 220 230 240Relay control voltage codes RD JD BD ED ND FD – – – –
d.c. supply Average resistance at 20 °C ± 10% W 90 360 1440 5700 7500 25 200 – – – –Operating voltage limits
Min. V 4. 9.6 19.2 3.4 4 – – – –Max. V 6.6 13.2 26.4 52. 66 121 – – – –
Relay control voltage codes – – B7 E7 – – F7 M7 P7 U7a.c. supply 60 Hz
Average resistance at 20 °C ± 15% W – – 400 1550 – – 10 200 35 500 3 500 42 500Operating voltage limits
Min. 50 Hz V – – 19.2 3.4 – – 96 176 14 19260 Hz – – 20.4 40. – – 102 17 195.5 204
Max. 50/60 Hz V – – 26.4 57.6 – – 144 264 276 2Socket characteristicsSocket type RSZ E1S35M RSZ E1S48MRelay types used RSB 1A120pp RSB 2A080pp, RSB 1A160pp (1)
Contact terminal arrangement SeparateWire connection method ConnectorProduct certifications e
Conforming to standards IEC 6194, UL, CSAElectrical characteristics
Conventional thermal current (Ith) A 12Maximum operating voltage V 300Insulation characteristics
Between adjacent output contacts Vrms 2500Between input and output contacts Vrms 2500Between contacts and 5 rail Vrms 2500General characteristics
Ambient air temperaturearound the device
Operation °C - 25…+ 5Storage °C - 40…+ 5
Degree of protection Conforming to IEC/EN 60529 IP 20Cablingscrew connector
Solid cable without cable end
1 conductor 0.5…2.5 mm2 - AWG 20…AWG 142 conductors 0.5…1.5 mm2 - AWG 20…AWG 16
Flexible cable with cable end
1 conductor 0.25…2.5 mm2 - AWG 22…AWG 142 conductors 0.25…1 mm2 - AWG 22…AWG 17
Maximum tightening torque / Screw size Nm 0. / M3 screwMounting On 35 mm 5 rail / on panelFixing on 5 rail By plastic compression springTerminal referencing IECBus jumper (Ith: 5 A) NoCompatibility with the metal maintaining clamp Yes, plasticTimer module NoProtection module All RZM pppClip-in legends YesWire connection method Screw connector
(1) When using the relay with socket RSZ E1S48M, terminals must be linked. See connection schemes on page 21.
104
0,80 0,4 1,21 1,6 2
107
105
106
C
A
B
Dur
abili
ty (N
umbe
r of o
pera
ting
cycl
es)
Switching capacity (kVA)
104
0,80 0,4 1,21 1,6 2
107
105
106
C
A
B
Dur
abili
ty (N
umbe
r of o
pera
ting
cycl
es)
Switching capacity (kVA)
0,3
0,5
0,61 0,4 0,2
0,4
0,60,
1
Red
uctio
n co
effic
ient
(A)
0,3
0,5
0,61 0,4 0,2
0,4
0,60,
1
Red
uctio
n co
effic
ient
(A)
0,1
12
16
100 200 30010 20 30 50
5
12
0,5
50
CB
A
Cur
rent
c
Voltage c
0,1
12
16
100 200 30010 20 30 50
5
12
0,5
50
CB
A
Cur
rent
c
Voltage c
Zelio Relay - plug-in relaysRSB interface relays
Characteristics
1
2
3
4
5
6
7
8
9
10
20
Relays for standard applicationsControl circuit voltage
Sold in lots of
Number and type of contacts - Thermal current (Ith)1 C/O - 12 A 1 C/O - 16 A 2 C/O - 8 AUnit reference (1)
Unit reference (1)
Unit reference (1)
Weight
V kgc 6 10 RSB 1A120RD RSB 1A160RD RSB 2A080RD 0.014
c 12 10 RSB 1A120JD RSB 1A160JD RSB 2A080JD 0.014
c 24 10 RSB 1A120BD RSB 1A160BD RSB 2A080BD 0.014
c 4 10 RSB 1A120ED RSB 1A160ED RSB 2A080ED 0.014
c 60 10 RSB 1A120ND RSB 1A160ND RSB 2A080ND 0.014
c 110 10 RSB 1A120FD RSB 1A160FD RSB 2A080FD 0.014
a 24 10 RSB 1A120B7 RSB 1A160B7 RSB 2A080B7 0.014
a 4 10 RSB 1A120E7 RSB 1A160E7 RSB 2A080E7 0.014
a 120 10 RSB 1A120F7 RSB 1A160F7 RSB 2A080F7 0.014
a 220 10 RSB 1A120M7 RSB 1A160M7 RSB 2A080M7 0.014
a 230 10 RSB 1A120P7 RSB 1A160P7 RSB 2A080P7 0.014
a 240 10 RSB 1A120U7 RSB 1A160U7 RSB 2A080U7 0.014
Sockets 12 A, a 300 VContact terminal arrangement
Connection Relay type Sold in lots of
Unit reference
Weightkg
Separate Connector RSB 1A120pp 10 RSZ E1S35M 0.060RSB 1A160pp (2)RSB 2A00pp
10 RSZ E1S48M 0.050
Protection modulesDescription For
use withVoltage Sold in
lots ofUnit reference
Weight
V kgDiode All sockets c 6…230 10 RZM 040W 0.003
RC circuit All sockets a 24…60 10 RZM 041BN7 0.010a 110…240 10 RZM 041FU7 0.010
Diode + green LED All sockets c 6…24 10 RZM 031RB 0.004c 24…60 10 RZM 031BN 0.004c 110…230 10 RZM 031FPD 0.004
Varistor + green LED All sockets c or a 6…24 10 RZM 021RB 0.005c or a 24…60 10 RZM 021BN 0.005c or a 110…230 10 RZM 021FP 0.005
AccessoriesDescription For
use withSold in lots of
Unit reference
Weightkg
Plastic maintaining clamp All sockets 10 RSZ R215 0.002Legend All sockets 10 RSZ L300 0.001
(1) To order a relay complete with socket (sold in lots of 20): add suffix S to one of the following voltage codes JD, BD, B7, P7 or F7. Example: RSB 2A080BD + RSZ E1S48M becomes RSB 2A080RBS.
(2) When using the relay with socket RSZ E1S48M, terminals must be linked. See connection schemes on page 21.
RSB 1A120JD + RZM 031FPD + RSZ E1S35M
5605
3
RSB 1A120JD + RZM 031FPD + RSZ E1S35M
5605
3
RSB 1A160BD + RSZ E1S48M
5605
4
RSB 1A160BD + RSZ E1S48M
5605
4
RSB 2A080BD + RSZ E1S48M
5605
2
RSB 2A080BD + RSZ E1S48M
5605
2
RSZ R215
5605
5
RSZ R215
5605
5Zelio Relay - plug-in relaysRSB interface relays
References
Presentation:page 1
References:page 20
Characteristics:page 19
Dimensions, schemes:page 21
1
2
3
4
5
6
7
8
9
10
21
DimensionsInterface relaysRSB 1A120pp RSB 2A080pp, RSB 1A160pp
SocketsRSZ E1S35M RSZ E1S48M
(1) Relays(2) Protection module(3) Maintaining clamp(4) Legend
SchemesInterface relaysRSB 1A120pp RSB 1A160pp RSB 2A080pp
When using relay RSB 1A160pp with socket RSZ E1S48M terminals 11 and 21, 14 and 24, 12 and 22 must be linked
Protection modulesRZM 040W RZM 041ppp RZM 031ppp RZM 021ppp
– A2
+ A1
– A2
+ A1
– A2
+ A1
– A2
+ A1
15,7
7,5
3,5
12,5
3,929
16,5
2,5
3,5
15,7
7,5
3,5
12,5
3,929
16,5
2,5
3,5
15,7
7,5
5
12,5
3,9
5 29
152,
5
15,7
7,5
5
12,5
3,9
5 29
152,
5
61
67
78,5
(4)
15,5
29,4
34,5
50
27,5
(3)
(1)
(2)
11
14
12
A2 A1
61
67
78,5
(4)
15,5
29,4
34,5
50
27,5
(3)
(1)
(2)
11
14
12
A2 A1
(4)
21 11
24 14
22 12
A2 A1
61
67
78,5
15,5
29,4
34,5
50
27,5
(3)
(1)
(2)
(4)
21 11
24 14
22 12
A2 A1
61
67
78,5
15,5
29,4
34,5
50
27,5
(3)
(1)
(2)
A2
A1
111412
A2
A1
11
14
12
A2
A1
111412
A2
A1
11
14
12
A2
A1
21 11
22 12
24 14
A2
A1
11/2
114
/24
12/2
2
A2
A1
21 11
22 12
24 14
A2
A1
11/2
114
/24
12/2
2
A2
A1
21 11
22 12
24 14
A2
A1
212422
111412
A2
A1
21 11
22 12
24 14
A2
A1
212422
111412
Dimensions, schemes
Zelio Relay - plug-in relaysRSB interface relays
1
2
3
4
5
6
7
8
9
10
22
Presentation of the range The RXM miniature relay range comprises: 1 12 A relays with 2 C/O contacts, 10 A relays with 3 C/O contacts, 6 A relays with
4 C/O contacts and 3 A “low level” relays with 4 C/O contacts. All these relays have the same dimensions.
2 Sockets with mixed or separate contact terminals.3 Protection modules (diode, RC circuit or varistor). All these modules are common
to all sockets.4 A metal maintaining clamp for all sockets.5 A plastic maintaining clamp for all sockets.6 A 2-pole bus jumper that can be used on sockets with separate contact terminals
in order to simplify cabling when creating an equipotential link between the coil terminals.
7 Clip-in legends for all the sockets except RXZ E2M114.
Relay description 1 Spring return pushbutton for testing the contacts (green: c, red: a). 2 Mechanical “relay status” indicator.3 Removable lock-down door enabling forced maintaining of the contacts for test
sequences or maintenance purposes. During operation, this lock-down door must always be in the closed position.
4 LED (depending on version) indicating the relay status.5 Removable legend for relay identification.6 Four notches for rail mounting adapter or panel mounting adapter with fixing lugs.7 Eight, eleven or fourteen Faston type pins.8 Area by which the product can be easily gripped.9 Mounting adapter enabling direct mounting of the relay on a panel.10 Mounting adapter enabling direct mounting of the relay on a 5 rail.
Socket description Sockets with mixed contact terminals (1)
1 Connection by screw clamp terminals or screw connector.2 Fourteen female contacts for the relay pins.3 Location for protection modules.4 Locking components for plastic and metal maintaining clamps.5 Locating slot for mounting on 5 rail with its compression spring or fixing clip.6 Two or four fixing holes for panel mounting.
Sockets with separate contact terminals (2)1 Connection by screw connector. 2 Eight, eleven or fourteen female contacts for the relay pins.3 Location for protection modules.4 Locking components for plastic and metal maintaining clamps.5 Locating slot for mounting on 5 rail with its compression spring or fixing clip.6 Two fixing holes for panel mounting.7 Location for bus jumpers (see mounting on sockets on page 2).
(1) The inputs are mixed with the relay's supply, with the outputs being located on the opposite side of the socket.
(2) The inputs and outputs are separated from the relay supply.
5247
66 7
6
2
1
5
3
4or
5247
66 7
6
2
1
5
3
4or
1065
57 12
7
3
4
56
8
1065
57 12
7
3
4
56
8
1066
60 9
1066
60 9
1066
61 9
1066
61 9
1066
62 10
1066
62 10
1060
14 1
2
3
4
5
Outputs
Inputs
Relay supply5
6
1060
14 1
2
3
4
5
Outputs
Inputs
Relay supply5
6
1060
15 16
2
3
4
5 7
Outputs
Inputs
Relay supply5
1060
15 16
2
3
4
5 7
Outputs
Inputs
Relay supply5
Zelio Relay - plug-in relaysRXM miniature relays
Presentation
Presentation :page 22
Characteristics :pages 23 and 24
References :pages 25 and 26
Dimensions :pages 27 and 2
Schemes :page 29
Presentation :page 22
Characteristics :pages 23 and 24
References :pages 25 and 26
Dimensions :pages 27 and 2
Schemes :page 29
1
2
3
4
5
6
7
8
9
10
23
General characteristicsConforming to standards IEC/EN 6110-1 (iss. 2), UL 50, CSA C22-2 n° 14Product certifications UL, CSAAmbient air temperature around the device
Storage °C - 40… + 5Operation °C - 40… + 55
Vibration resistanceconforming to IEC/EN 6006-2-6
In operation 3 gn (10...150 Hz/± 1 mm / 5g/5 cycles)Not operating 5 gn (10...150 Hz/± 1 mm / 5g/5 cycles)
Degree of protection Conforming to IEC/EN 60529 IP 40Shock resistanceconforming to IEC/EN 6006-2-27
Opening 15 gnClosing 15 gn
Protection category RT IMounting position Any
Insulation characteristicsRated insulation voltage (Ui) V 250 (IEC), 300 (UL, CSA)Rated impulse withstand voltage (Uimp) kV 4 (1.2/50 ms)Dielectric strength(rms voltage)
Between coil and contact a V 1550Between poles a V 1550Between contacts a V 1500
Contact characteristicsRelay type RXM 2ABppp RXM 3ABppp RXM 4ABppp RXM 4GBppp
Number and type of contacts 2 C/O 3 C/O 4 C/O 4 C/O low levelContact materials AgNi AgAu - bifurcatedConventional thermal current (Ith)
For ambient temperature y 55 °C
A 12 10 6 3
Rated operational current in utilisation categories AC-1 and DC-1
Conforming to IEC "C" 12 10 6 2“O” 6 5 3 1
Conforming to UL 12 10 6 3Switching current Minimum mA 10 3Switching voltage Maximum V a/c 250 (IEC)
Minimum V 17 5Nominal load (resistive) A 12 / 250 a V 10 / 250 a V 6 / 250 a V 3 / 250 a V
A 12 / 2 c V 10 / 2 c V 6 / 2 c V 3 / 2 c VSwitching capacity Maximum a VA 3000 2500 1500 750
c W 336 20 16 4Minimum mW 170 15
Maximum operating rateIn operating cycles
No-load 1 000Under load 1200
Utilisation coefficient 20 %Mechanical durability In millions of operating cycles 10
Electrical durabilityIn millions of operating cycles
Resistive load 0.1Inductive load See curves below
Electrical durability of contacts Resistive load a
Reduction coefficient for inductive load a (depending on power factor cos j)
Maximum switching capacity on resistive load c
A RXM 2ABppp B RXM 3ABppp C RXM 4ABppp D RXM 4GBppp
Durability (inductive load) = durability (resistive load) x reduction coefficient.
105
106
107
2 30 1
A BDC
Dur
abili
ty (N
umbe
r of o
pera
ting
cycl
es)
Switching capacity (kVA)
105
106
107
2 30 1
A BDC
Dur
abili
ty (N
umbe
r of o
pera
ting
cycl
es)
Switching capacity (kVA)
0,3
0,5
0,61 0,4 0,2
0,4
0,60,
1
Red
uctio
n co
effic
ient
(A)
0,3
0,5
0,61 0,4 0,2
0,4
0,60,
1
Red
uctio
n co
effic
ient
(A)
0,1
1
200 2500 5028 100 150
10
3
6
CDBA
Cur
rent
c
Voltage c
0,1
1
200 2500 5028 100 150
10
3
6
CDBA
Cur
rent
c
Voltage c
Zelio Relay - plug-in relaysRXM miniature relays
Characteristics
1
2
3
4
5
6
7
8
9
10
24
Coil characteristicsAverage consumption a VA 1.2
c W 0.9Drop-out voltage threshold a u 0.15 Uc
c u 0.1 UcOperating time(response time)
Between coil energisation and making of the On-delay contact
a ms 20c ms 20
Between coil de-energisation and making of the Off-delay contact
a ms 20c ms 20
Control circuit voltage Uc V 12 24 48 110 120 125 220 230 240Relay control voltage codes JD BD ED FD – GD MD – –
d.c. supply Average resistance at 20 °C ± 10% W 160 650 2600 11 000 – 11 000 14 000 – –Operating voltage limits Min. V 9.6 19.2 3.4 – 100 176 – –
Max. V 13.2 26.4 52. 121 – 13 242 – –Relay control voltage codes – B7 E7 F7 – – P7 U7
a.c. supply Average resistance at 20 °C ± 15% W – 10 770 – 4430 – – 15 000 15 500Operating voltage limits Min. V – 19.2 3.4 – 96 – – 14 192
Max. V – 26.4 52. – 132 – – 253 264
Socket characteristicsSocket type RXZ E2S108M RXZ E2S111M RXZ E2S114M RXZ E2M114M RXZ E2M114Relay types used RXM 2ppppp RXM 3ppppp RXM 4ppppp RXM 2ppppp (1)
RXM 4pppppRXM 2ppppp (1)RXM 4ppppp
Contact terminal arrangement Separate MixedWire connection method Connector Screw clamp
terminalsProduct certifications UL, CSAConforming to standards IEC 6194, e
Electrical characteristicsConventional thermal current (Ith) A 12 10Maximum operating voltage V 250 (IEC)
Insulation characteristicsBetween adjacent output contacts Vrms 2500Between input and output contacts Vrms 2500Between contacts and 5 rail Vrms 2500
General characteristicsAmbient air temperaturearound the device
Operation °C - 40…+ 55Storage °C - 40…+ 5
Degree of protection Conforming to IEC/EN 60529 IP 20Cabling Solid cable
without cable end
1 conductor 0.5…2.5 mm2 - AWG 20…AWG 14 0.5… 1.5 mm2 AWG 20…AWG 16
2 conductors 0.5…1.5 mm2 - AWG 20…AWG 16Flexible cable with cable end
1 conductor 0.25…2.5 mm2 - AWG 22…AWG 14 0.25…1 mm2
AWG 22…AWG 172 conductors 0.25…1 mm2 - AWG 22…AWG 17
Maximum tightening torque / Screw size Nm 1 / M3 screwMounting On 35 mm 5 rail / on panelFixing on 5 rail By red plastic clip By metal
compression spring
By red plastic clip
Terminal referencing IEC, NEMABus jumper (Ith: 5 A) Yes NoCompatibility with the plastic maintaining clamp YesCompatibility with the metal maintaining clamp YesProtection module All RXM 040W, RXM 041pp, RXM 021pp
Clip-in legends Yes NoWire connection method Screw connector Screw clamp
terminals
(1) When mounting relay RXM 2ppppp on socket RXZ E2Mpppp, the thermal current must not exceed 10 A.
Zelio Relay - plug-in relaysRXM miniature relays
Characteristics (continued)
Presentation :page 22
Characteristics :pages 23 and 24
References :pages 25 and 26
Dimensions :pages 27 and 2
Schemes :page 29
Presentation :page 22
Characteristics :pages 23 and 24
References :pages 25 and 26
Dimensions :pages 27 and 2
Schemes :page 29
1
2
3
4
5
6
7
8
9
10
25
Miniature relays without LED (sold in lots of 10) Control circuit voltage
Number and type of contacts - Thermal current (Ith)2 C/O - 12 A 3 C/O - 10 A 4 C/O - 6 AUnit reference
Weight Unit reference
Weight Unit reference
Weight
V kg kg kgc 12 RXM 2AB1JD 0.037 RXM 3AB1JD 0.037 RXM 4AB1JD 0.037c 24 RXM 2AB1BD 0.037 RXM 3AB1BD 0.037 RXM 4AB1BD 0.037c 4 RXM 2AB1ED 0.037 RXM 3AB1ED 0.037 RXM 4AB1ED 0.037c 110 RXM 2AB1FD 0.037 RXM 3AB1FD 0.037 RXM 4AB1FD 0.037c 220 – – – – RXM 4AB1MD 0.037
a 24 RXM 2AB1B7 0.037 RXM 3AB1B7 0.037 RXM 4AB1B7 0.037a 4 RXM 2AB1E7 0.037 RXM 3AB1E7 0.037 RXM 4AB1E7 0.037a 120 RXM 2AB1F7 0.037 RXM 3AB1F7 0.037 RXM 4AB1F7 0.037a 230 RXM 2AB1P7 0.037 RXM 3AB1P7 0.037 RXM 4AB1P7 0.037a 240 – – – – RXM 4AB1U7 0.037
Miniature relays with LED (sold in lots of 10) c 12 RXM 2AB2JD 0.037 RXM 3AB2JD 0.037 RXM 4AB2JD 0.037c 24 RXM 2AB2BD 0.037 RXM 3AB2BD 0.037 RXM 4AB2BD 0.037c 4 RXM 2AB2ED 0.037 RXM 3AB2ED 0.037 RXM 4AB2ED 0.037c 110 RXM 2AB2FD 0.037 RXM 3AB2FD 0.037 RXM 4AB2FD 0.037c 125 – – – – RXM 4AB2GD 0.037
a 24 RXM 2AB2B7 0.037 RXM 3AB2B7 0.037 RXM 4AB2B7 0.037a 4 RXM 2AB2E7 0.037 RXM 3AB2E7 0.037 RXM 4AB2E7 0.037a 120 RXM 2AB2F7 0.037 RXM 3AB2F7 0.037 RXM 4AB2F7 0.037a 230 RXM 2AB2P7 0.037 RXM 3AB2P7 0.037 RXM 4AB2P7 0.037
Miniature relays with low level contacts, without LED (sold in lots of 10) Control circuit voltage
Number and type of contacts Thermal current (Ith)4 C/O - 3 AUnit reference
Weight
V kgc 12 RXM 4GB1JD 0.037c 24 RXM 4GB1BD 0.037c 4 RXM 4GB1ED 0.037c 110 RXM 4GB1FD 0.037
a 24 RXM 4GB1B7 0.037a 4 RXM 4GB1E7 0.037a 120 RXM 4GB1F7 0.037a 230 RXM 4GB1P7 0.037
Miniature relays with low level contacts, with LED (sold in lots of 10) c 12 RXM 4GB2JD 0.037c 24 RXM 4GB2BD 0.037c 4 RXM 4GB2ED 0.037c 110 RXM 4GB2FD 0.037
a 24 RXM 4GB2B7 0.037a 4 RXM 4GB2E7 0.037a 120 RXM 4GB2F7 0.037a 230 RXM 4GB2P7 0.037a 240 RXM 4GB2U7 0.037
RXM pAB1F7
1066
5
RXM pAB1F7
1066
5
RXM pAB2F7
1066
57
RXM pAB2F7
1066
57
RXM 4GB1F7
1065
5
RXM 4GB1F7
1065
5
RXM 4GB2F7
1066
57
RXM 4GB2F7
1066
57
Zelio Relay - plug-in relaysRXM miniature relays
References
1
2
3
4
5
6
7
8
9
10
26
Miniature relays without LED (sold in lots of 100)Control circuit voltage
Number and type of contacts - Thermal current (Ith)2 C/O - 12 A 4 C/O - 6 AUnit reference
Weight Unit reference
Weight
V kg kgc 12 – – RXM 4AB1JDTQ 0.036c 24 RXM 2AB1BDTQ 0.037 RXM 4AB1BDTQ 0.036c 4 – – RXM 4AB1EDTQ 0.036c 110 – – RXM 4AB1FDTQ 0.036c 220 – – RXM 4AB1MDTQ 0.036
a 24 RXM 2AB1B7TQ 0.037 RXM 4AB1B7TQ 0.036a 4 – – RXM 4AB1E7TQ 0.036a 120 RXM 2AB1F7TQ 0.037 RXM 4AB1F7TQ 0.036a 230 RXM 2AB1P7TQ 0.037 RXM 4AB1P7TQ 0.036
Miniature relays with LED (sold in lots of 100)c 24 – – RXM 4AB2BDTQ 0.036a 24 RXM 2AB2B7TQ 0.037 RXM 4AB2B7TQ 0.036a 230 RXM 2AB2P7TQ 0.037 RXM 4AB2P7TQ 0.036
SocketsContact terminal arrangement
Connection Relay type Sold in lots of
Unit reference
Weightkg
Mixed Screw clamp terminals RXM 2pppp (3)RXM 4pppp
10 RXZ E2M114 (1) 0.04
Screw connector RXM 2pppp (3)RXM 4pppp
10 RXZ E2M114M (1) 0.056
Separate Screw connector RXM 2pppp 10 RXZ E2S108M (2) 0.05RXM 3pppp 10 RXZ E2S111M (1) 0.066RXM 4pppp 10 RXZ E2S114M (1) 0.070
Protection modulesDescription Voltage For
use withSold in lots of
Unit reference
Weight
V kgDiode c 6...250 All sockets 20 RXM 040W 0.003
RC circuit a 24...60 All sockets 20 RXM 041BN7 0.010a 110...240 All sockets 20 RXM 041FU7 0.010
Varistor a/c 6...24 All sockets 20 RXM 021RB 0.030a/c 24...60 All sockets 20 RXM 021BN 0.030a/c 110...240 All sockets 20 RXM 021FP 0.030
Timing relaysDescription For
use withUnit reference
Weightkg
2 or 4 timed C/O contacts (function A)
Sockets RXZ Eppppp RE XL2pp (4) –RE XL4pp (4) –
AccessoriesDescription For
use withSold in lots of
Unit reference
Weightkg
Metal maintaining clamp All sockets 10 RXZ 400 0.001Plastic maintaining clamp All sockets 10 RXZ R335 0.005Bus jumper 2-pole (Ith: 5 A) All sockets with separate contacts 10 RXZ S2 0.005
Mounting adapter for 5 rails (5)
All relays 10 RXZ E2DA 0.004
Mounting adapter with fixing lugs for panel
All relays 10 RXZ E2FA 0.002
Clip-in legends All relays (sheet of 10 legends) 10 RXZ L520 0.00All sockets except RXZ E2M114 10 RXZ L420 0.001
(1) Thermal current Ith: 10 A(2) Thermal current Ith: 12 A(3) When mounting relay RXM 2ppppp on socket RXZ E2Mpppp, the thermal current must not exceed 10 A. (4) Please consult the "Zelio Time timing relays" catalogue.(5) Test button becomes inaccessible.
RXZ E2M114M + Relais RXM 4AB2F7
1060
16
RXZ E2M114M + Relais RXM 4AB2F7
1060
1610
6017
RXZ E2S114M + Relais RXM 4AB2F7
1060
17
RXZ E2S114M + Relais RXM 4AB2F7
1060
1
RXM 041pp7
1060
1
RXM 041pp7
5351
95
RE XL4pp
5351
95
RE XL4pp
5364
4
RXZ 400
5364
4
RXZ 400
Presentation :page 22
Characteristics :pages 23 and 24
References :pages 25 and 26
Dimensions :pages 27 and 2
Schemes :page 29
Presentation :page 22
Characteristics :pages 23 and 24
References :pages 25 and 26
Dimensions :pages 27 and 2
Schemes :page 29
Zelio Relay - plug-in relaysRXM miniature relays
References (continued)
1
2
3
4
5
6
7
8
9
10
27
DimensionsMiniature relaysRXM pppppp RXM 2 RXM 3 RXM 4
Common view Pin side view
SocketsRXZ E2M114 RXZ E2M114M
Common side view RXZ E2S108M RXZ E2S111M RXZ E2S114M
(1) Relays(2) Protection module(3) Maintaining clamp(4) 2 elongated holes Ø 3.5 x 6.5(5) 2 bus jumpers
(1)
(2)(3)
25,5
347
A214
A113
246
448
145
12
1
11
9
21
10
31
11
41
12
22
2
32
3
42
4
(4)19
40
309
232130
697
39,5
61
3,5
79
(4)
(1)
(2)(3)
25,5
347
A214
A113
246
448
145
12
1
11
9
21
10
31
11
41
12
22
2
32
3
42
4
(4)19
40
309
232130
697
39,5
61
3,5
79
(4)
17
43
23,550
27677
40
80
44
8
34
7
24
6
14
5
42
4
32
3
22
2
12
1
A1
13
A2
1441
12
31
11
21
10
11
9
(3)
(1)
(2)
17
43
23,550
27677
40
80
44
8
34
7
24
6
14
5
42
4
32
3
22
2
12
1
A1
13
A2
1441
12
31
11
21
10
11
9
(3)
(1)
(2)
19
61
2923
707
3,5
79
(3) (2)
(1)
(5)
19
61
2923
707
3,5
79
(3) (2)
(1)
(5)23,5
27
38
41
12
11
9
44
8
14
5
A1
13
A2
14
42
4
12
1
23,5
27
38
41
12
11
9
44
8
14
5
A1
13
A2
14
42
4
12
1
23,5
27
38
319
346
A1
13
A2
14
32
3
218
245
22
2
117
144
12
1
23,5
27
38
319
346
A1
13
A2
14
32
3
218
245
22
2
117
144
12
1
23,5
27
38
41
12
31
11
21
10
11
944
8
34
7
24
6
14
542
4
32
3
22
2
12
1
A1
13
A2
14
23,5
27
38
41
12
31
11
21
10
11
944
8
34
7
24
6
14
542
4
32
3
22
2
12
1
A1
13
A2
14
Zelio Relay - plug-in relaysRXM miniature relays
Dimensions
40 21
27
9 6 2,5 2,521
6,3
6,3
4,2
4,2
13,22,5 2,5 4,4
21
13,2
6,6 6,6
2,5 2,513,2
4,4 4,44,4
1
2
3
4
5
6
7
8
9
10
2
Dimensions (continued)Plastic clamp and clip-in legendsRXZ R335 RXZ L420 Mounting on all sockets (1)
(1) Clip-in legends for all sockets except RXZ E2M114
Bus jumper Metal clampRXZ S2 Mounting on sockets with separate contacts
(view from below)RXZ 400
Example of bus jumper mounting on sockets
(1) 2 bus jumpers (polarity A2)(2) 2 bus jumpers (polarity A1)
Mounting adapter for rails (1) Mounting adapter for panelRXZ E2DA RXZ E2FA
(1) Test button becomes inaccessible
57
27
57
27
12
14,2
26,5
12
14,2
26,5
81
94,5
(1)
81
94,5
(1)
2,2 7,
3
25
22
2,3
2,2 7,
3
25
22
2,3(1)(1)
(2)(2)
(1)(1)
(2)(2)
22
42
0,
22
42
0,
38
6 424
348
23
51
38
6 424
348
23
51
48 49
3,5
43 38
4
24
3,5
48 49
3,5
43 38
4
24
3,5
Presentation :page 22
Characteristics :pages 23 and 24
References :pages 25 and 26
Dimensions :pages 27 and 2
Schemes :page 29
Presentation :page 22
Characteristics :pages 23 and 24
References :pages 25 and 26
Dimensions :pages 27 and 2
Schemes :page 29
Zelio Relay - plug-in relaysRXM miniature relays
Dimensions (continued)
1
2
3
4
5
6
7
8
9
10
29
SchemesMiniature relaysRXM 2ppppp RXM 3ppppp RXM 4ppppp
Symbols shown in blue correspond to Nema marking.
Sockets RXZ E2M114 RXZ E2M114M
347
14A2 A1
13
246
844 14
5
1
119
2110
3111
4112
2312223242
4
448
347
246
145
12312223242
4
14A2 A1
13
14 13
1021
9
9
5
1
111131
1241
Symbols shown in blue correspond to Nema marking.RXZ E2S108M RXZ E2S111M RXZ E2S114M
1241 11
9
844 14
5
A1
13
A2
A1A214
424
121
INPUT
A1
13
A2
A1A214
319
346
3
218
245
2
117
144
32 22 121
INPUT
A1
13
A2
A1A214
4112
3111
2110
119
448
347
246
145
424
323
222
121
INPUT
Symbols shown in blue correspond to Nema marking.Protection modules RXM 040W RXM 041ppp RXM 021ppp
– A2
+ A1
– A2
+ A1
– A2
+ A1
A2
A1
414442
111412
1
125
149
11
4
428
4412
4113
A1
14
A2
A2
A1
414442
111412
1
125
149
11
4
428
4412
4113
A1
14
A2
A2
A1
313432
212422
111412
1
12
4
147
11
2
22
5
248
21
3
32
6
349
3113
A1
14
A2
A2
A1
313432
212422
111412
1
12
4
147
11
2
22
5
248
21
3
32
6
349
3113
A1
14
A2
A2
A1
414442
212422
313432
111412
1
125
149
11
4
428
4412
41
2
226
2410
21
3
327
3411
3113
A1
14
A2
A2
A1
414442
212422
313432
111412
1
125
149
11
4
428
4412
41
2
226
2410
21
3
327
3411
3113
A1
14
A2
Zelio Relay - plug-in relaysRXM miniature relays
Schemes
1
2
3
4
5
6
7
8
9
10
30
Presentation of the range The RUM universal relay range comprises: 1 10 A relays with 2 and 3 C/O contacts, with cylindrical or flat (Faston type) pins,
and 3 A low level relays with 3 C/O contacts, with cylindrical pins. All these relays have the same dimensions.
2 Sockets with mixed or separate contact terminals.3 Protection modules (diode, RC circuit or varistor) or 1 timer module. All these
modules are common to all sockets.4 A metal maintaining clamp for all sockets.5 A 2-pole bus jumper that can be used on sockets with separate contact terminals
in order to simplify cabling when creating an equipotential link between the coil terminals.
6 Clip-in legends for the sockets.
Relay description 1 Spring return pushbutton for testing the contacts (green: c, red: a). 2 Mechanical “relay status” indicator.3 Removable lock-down door enabling forced maintaining of the contacts for test
sequences or maintenance purposes. During operation, this lock-down door must always be in the closed position.
4 LED (depending on version) indicating the relay status.5 Removable legend for relay identification.6 Area by which the product can be easily gripped.7 Eight or eleven cylindrical pins. 8 Eight or eleven flat (Faston type) pins
Socket description Sockets with mixed contact terminals (1)
1 Connection by screw connector. 2 Eight or eleven female contacts for the relay cylindrical pins.3 Location for protection modules or the timer module.4 Locking component for metal maintaining clamp.5 A locating slot for mounting on 5 rail.6 Two fixing holes for panel mounting.
Sockets with separate contact terminals (2)1 Connection by screw connector. 2 a Eight or eleven female contacts for the relay cylindrical pins.
b Eleven female contacts for the relay flat pins.3 Location for protection modules or the timer module.4 Locking component for metal maintaining clamp.5 Locating slot for mounting on 5 rail with fixing clip.6 Two fixing holes for panel mounting.7 Location for bus jumpers (see mounting on sockets on page 36).
(1) The inputs are mixed with the relay's supply, with the outputs being located on the opposite side of the socket.
(2) The inputs and outputs are separated from the relay supply.
5362
94
6
5
2
1
3
4
5362
94
6
5
2
1
3
4
1066
63 12
34
5
6
1066
63 12
34
5
6
1060
22 1
2
3
4
5
6
Outputs
Relay supply
Inputs
Relay suppy
1060
22 1
2
3
4
5
6
Outputs
Relay supply
Inputs
Relay suppy
1060
23 16
2a
3
4
5 7
Inputs
Outputs
Relay supply5
1060
23 16
2a
3
4
5 7
Inputs
Outputs
Relay supply5
1060
24 1
2b
3
4
5 7
Inputs
Outputs
Relay supply5
1060
24 1
2b
3
4
5 7
Inputs
Outputs
Relay supply5
Zelio Relay - plug-in relaysRUM universal relays
Presentation
Characteristics :page 31
References :pages 33 and 34
Dimensions :page 35
Schemes :page 37
Setting-up :page 39
Characteristics :page 31
References :pages 33 and 34
Dimensions :page 35
Schemes :page 37
Setting-up :page 39
1
2
3
4
5
6
7
8
9
10
31
General characteristicsConforming to standards IEC/EN 6110-1 (iss. 2), UL 50, CSA C22-2 n° 14Product certifications UL, CSAAmbient air temperature around the device
Storage °C - 40… + 5Operation °C - 40… + 55
Vibration resistanceconforming to IEC/EN 6006-2-6
In operation 3 gn (10...150 Hz/± 1 mm / 5g/5 cycles)Not operating 4 gn (10...150 Hz/± 1 mm / 5g/5 cycles)
Degree of protection Conforming to IEC/EN 60529 IP 40Shock resistanceconforming to IEC/EN 6006-2-27
Opening 10 gnClosing 10 gn
Protection category RT IMounting position Any
Insulation characteristicsRated insulation voltage (Ui) Conforming to IEC/EN 60947 V 250 (IEC), 300 (UL, CSA)Rated impulse withstand voltage (Uimp) kV 4 (1.2/50 ms)Dielectric strength(rms voltage)
Between coil and contact a V 1550Between poles a V 1550Between contacts a V 1500
Contact characteristicsRelay type RUM F2ppp RUM F3ppp RUM C2ppp RUM C3App RUM C3Gpp
Number and type of contacts 2 C/O 3 C/O 2 C/O 3 C/O 3 C/O low levelContact materials . AgNi AgAuConventional thermal current (Ith)
For ambient temperature y 55°C
A 10 3
Rated operational current in utilisation categories AC-1 and DC-1
Conforming to IEC "C" A 10 2“O” A 5 1
Conforming to UL A 16 / a 277 V 12 / c 2 V
3
Switching current Minimum mA 10 3Switching voltage Maximum V a/c 250 (IEC)
Minimum V 17 5Nominal load (resistive) A 10 / 250 a V 3 / 250 a V
A 10 / 2 c V 3 / 2 c VSwitching capacity Maximum a VA 2500 750
c W 20 4Minimum mW 170 15
Maximum operating rateIn operating cycles/hour
No-load 1 000Under load 1200
Utilisation coefficient 20 %Mechanical durability In millions of operating cycles 5Electrical durability In millions of operating cycles
Resistive load 0.1Inductive load See curves below
Electrical durability of contactsResistive load a
Reduction coefficient for inductive load a (depending on power factor cos j)
Maximum switching capacity on resistive load c
A RUM Fppppp, RUM C2ppp, RUM C3Appp B RUM C3Gppp
Durability (inductive load) = durability (resistive load) x reduction coefficient.
105
106
107
2 30 1
AB
Dur
abili
ty (N
umbe
r of o
pera
ting
cycl
es)
Switching capacity (kVA)
105
106
107
2 30 1
AB
Dur
abili
ty (N
umbe
r of o
pera
ting
cycl
es)
Switching capacity (kVA)
0,3
0,5
0,61 0,4 0,2
0,4
0,60,
1
Red
uctio
n c
oeffi
cien
t (A
)
0,3
0,5
0,61 0,4 0,2
0,4
0,60,
1
Red
uctio
n c
oeffi
cien
t (A
)
0,1
1
200 2500 50 100 150
10
3
B A
28
Cur
rent
c
Voltage c
0,1
1
200 2500 50 100 150
10
3
B A
28
Cur
rent
c
Voltage c
Zelio Relay - plug-in relaysRUM universal relays
Characteristics
1
2
3
4
5
6
7
8
9
10
32
Coil characteristicsAverage consumption a VA 2...3
c W 1.4Drop-out voltage threshold a u 0.15 Uc
c u 0.1 UcOperating time(response time)
Between coil energisation and making of the On-delay contact
a ms 20c ms 20
Between coil de-energisation and making of the Off-delay contact
a ms 20c ms 20
Control circuit voltage Uc V 12 24 48 60 110 120 125 220 230Relay control voltage codes JD BD ED ND FD – GD MD –
d.c. supply Average resistance at 20 °C ± 10% W 120 470 100 2790 10 000 – 10 000 3700 –Operating voltage limits
Min. V 9.6 19.2 3.4 4 – 100 176 –Max. V 13.2 26.4 52. 66 121 – 137.5 242 –
Relay control voltage codes – B7 E7 – – F7 – – P7a.c. supply Average resistance at 20 °C ± 15% W – 72 290 – – 1700 – – 7200
Operating voltage limits
Min. V – 19.2 3.4 – – 96 – – 14Max. V – 26.4 52. – – 132 – – 253
Socket characteristicsSocket type RUZ C2M RUZ C3M RUZ SC2M RUZ SC3M RUZ SF3MRelay types used RUM C2ppppp RUM C3ppppp RUM C2ppppp RUM C3ppppp RUM Fppppp
Contact terminal arrangement Mixed SeparateWire connection method ConnectorProduct certifications UL, CSA Conforming to standards IEC 6194, e
Electrical characteristicsConventional thermal current (Ith) A 10 12Maximum operating voltage V 250 (IEC)
Insulation characteristicsBetween adjacent output contacts Vrms 2500Between input and output contacts Vrms 2500Between contacts and 5 rail Vrms 2500
General characteristicsAmbient air temperaturearound the device
Operation °C - 40…+ 55Storage °C - 40…+ 5
Degree of protection Conforming to IEC/EN 60529 IP 20Cabling Solid cable
without cable end
1 conductor 0.5…2.5 mm2 - AWG 20…AWG 142 conductors 0.5…1.5 mm2 - AWG 20…AWG 16
Flexible cable with cable end
1 conductor 0.25…2.5 mm2 - AWG 22…AWG 142 conductors 0.25…1 mm2 - AWG 22…AWG 17
Maximum tightening torque / Screw size Nm 1 / M3.3 screwMounting On 35 mm 5 rail / on panelFixing on 5 rail By red plastic clipTerminal referencing IEC, NEMABus jumper (Ith: 5 A) No YesCompatibility with the metal maintaining clamp YesTimer module YesProtection module All RUW 24ppp
Clip-in legends No YesWire connection method Screw connector
Zelio Relay - plug-in relaysRUM universal relays
Characteristics (continued)
Characteristics :page 31
References :pages 33 and 34
Dimensions :page 35
Schemes :page 37
Setting-up :page 39
Characteristics :page 31
References :pages 33 and 34
Dimensions :page 35
Schemes :page 37
Setting-up :page 39
1
2
3
4
5
6
7
8
9
10
33
ReferencesRelays for standard applications, without LED (sold in lots of 10)Pins Control
circuit voltageNumber and type of contacts - Thermal current (Ith)2 C/O - 10 A 3 C/O - 10 AUnit reference
Weight Unit reference
Weight
V kg kgCylindrical c 12 RUM C2AB1JD 0.05 RUM C3AB1JD 0.0
c 24 RUM C2AB1BD 0.05 RUM C3AB1BD 0.0c 4 RUM C2AB1ED 0.05 RUM C3AB1ED 0.0c 60 – – RUM C3AB1ND 0.0c 110 RUM C2AB1FD 0.05 RUM C3AB1FD 0.0c 125 – – RUM C3AB1GD 0.0c 220 – – RUM C3AB1MD 0.0
a 24 RUM C2AB1B7 0.05 RUM C3AB1B7 0.0a 4 RUM C2AB1E7 0.05 RUM C3AB1E7 0.0a 120 RUM C2AB1F7 0.05 RUM C3AB1F7 0.0a 230 RUM C2AB1P7 0.05 RUM C3AB1P7 0.0
Flat (Faston type) c 12 RUM F2AB1JD 0.00 RUM F3AB1JD 0.02c 24 RUM F2AB1BD 0.00 RUM F3AB1BD 0.02c 4 RUM F2AB1ED 0.00 RUM F3AB1ED 0.02c 110 RUM F2AB1FD 0.00 RUM F3AB1FD 0.02
a 24 RUM F2AB1B7 0.00 RUM F3AB1B7 0.02a 4 RUM F2AB1E7 0.00 RUM F3AB1E7 0.02a 120 RUM F2AB1F7 0.00 RUM F3AB1F7 0.02a 230 RUM F2AB1P7 0.00 RUM F3AB1P7 0.02
Relays for standard applications, with LED (sold in lots of 10)Cylindrical c 12 RUM C2AB2JD 0.05 RUM C3AB2JD 0.0
c 24 RUM C2AB2BD 0.05 RUM C3AB2BD 0.0c 4 RUM C2AB2ED 0.05 RUM C3AB2ED 0.0c 60 – – RUM C3AB2ND 0.0c 110 RUM C2AB2FD 0.05 RUM C3AB2FD 0.0c 125 – – RUM C3AB2GD 0.0
a 24 RUM C2AB2B7 0.05 RUM C3AB2B7 0.0a 4 RUM C2AB2E7 0.05 RUM C3AB2E7 0.0a 120 RUM C2AB2F7 0.05 RUM C3AB2F7 0.0a 230 RUM C2AB2P7 0.05 RUM C3AB2P7 0.0
Flat (Faston type) c 12 RUM F2AB2JD 0.04 RUM F3AB2JD 0.02c 24 RUM F2AB2BD 0.04 RUM F3AB2BD 0.02c 4 RUM F2AB2ED 0.04 RUM F3AB2ED 0.02c 110 RUM F2AB2FD 0.04 RUM F3AB2FD 0.02
a 24 RUM F2AB2B7 0.04 RUM F3AB2B7 0.02a 4 RUM F2AB2E7 0.04 RUM F3AB2E7 0.02a 120 RUM F2AB2F7 0.04 RUM F3AB2F7 0.02a 230 RUM F2AB2P7 0.04 RUM F3AB2P7 0.02
Relays with low level contacts, with LED (sold in lots of 10)Pins Control
circuit voltageNumber and type of contacts Thermal current (Ith)3 C/O - 3 AUnit reference
Weight
V kgCylindrical c 24 RUM C3GB2BD 0.06
c 4 RUM C3GB2ED 0.06
a 24 RUM C3GB2B7 0.06a 4 RUM C3GB2E7 0.06a 120 RUM C3GB2F7 0.06a 230 RUM C3GB2P7 0.06
Zelio Relay - plug-in relaysRUM universal relays
References
RUM ppAB1F7
1066
64
RUM ppAB2F7
1066
63
1
2
3
4
5
6
7
8
9
10
34
References (continued)SocketsContact terminal arrangement
Connection Relay type Sold in lots of
Unit reference
Weightkg
Mixed Screw connector RUM C2ppppp 10 RUZ C2M 0.054RUM C3ppppp 10 RUZ C3M 0.054
Separate Screw connector RUM C2ppppp 10 RUZ SC2M 0.095RUM C3ppppp 10 RUZ SC3M 0.100RUM F2pppp 10 RUZ SF3M 0.095RUM F3pppp
Protection modulesDescription For
use withVoltage Sold in
lots ofUnit reference
Weight
V kgDiode All sockets c 6…250 10 RUW 240BD 0.004
RC circuit All sockets a 110…240 10 RUW 241P7 0.004
Varistor All sockets a/c 24 10 RUW 242B7 0.004a/c 240 10 RUW 242P7 0.004
Timer moduleDescription For
use withVoltage Reference Weight
V kgMultifunction All sockets a/c 24… 240 RUW 101MW 0.020
Timing relaysDescription For
use withReference Weight
kg2 timed C/O contacts (single-function or multifunction)
On sockets RUZ CpM RE 48A pp (1)
–
AccessoriesDescription For
use withSold in lots of
Unit reference
Weightkg
Metal maintaining clamp All sockets 10 RUZC200 0.001
Bus jumper 2-pole (Ith : 5 A) All sockets with separate contacts 10 RUZ S2 0.005
Clip-in legends All relays(sheet of 10 legends)
10 RXZ L520 0.00
All sockets with separate contacts 10 RUZ L420 0.001
(1) Please consult the "Zelio Time timing relays" catalogue.
Zelio Relay - plug-in relaysRUM universal relays
References (continued)
Characteristics :page 31
References :pages 33 and 34
Dimensions :page 35
Schemes :page 37
Setting-up :page 39
Characteristics :page 31
References :pages 33 and 34
Dimensions :page 35
Schemes :page 37
Setting-up :page 39
RUZ C200
5364
5
RUW 101MW
106
02
RUW 241P7
1060
27
RUZ C3M + relais RUM C3ppppp
1060
25
RUZ S2
5352
03
1
2
3
4
5
6
7
8
9
10
35
DimensionsUniversal relaysRUM Cpp RUM Fpp
SocketsCommon side view RUZ C2M RUZ C3M
38
37
30
24
6
27
A2
7
A1
2
11
1
21
8
A2
7
INPUT A2INPUT A1
22
5
12
4
1
4
2
3
8
5
7
6
14
3
38
37
30
A2
10
A2
10
31
11
21
6
11
1
A1
2
34
9
32
8
24
7
22
5
14
3
12
4
210
1
6
2
5
3
4
1110
7
9
8
INPUT A2INPUT A1
RUZ SC2M RUZ SC3M
(1) Relays(2) Protection module(3) Maintaining clamp(4) 2 bus jumpers
55 35
35
9 55 35
35
9
35
35539
35
35539
74
27
22
6389
93
(1)(3)
(2)
474
27
22
6389
93
(1)(3)
(2)
4
3675
102
105
29
924
40
30
19
45
225
111
124
246
1
4
2
3
8
5
7
6
A27
A12
218
143
Ø 4
(4)
(1)(3)
(2)
3675
102
105
29
924
40
30
19
45
225
111
124
246
1
4
2
3
8
5
7
6
A27
A12
218
143
Ø 4
(4)
(1)(3)
(2)
3675
102
105
29
924
40
32
63
3111
216
111
32
8
22
5
12
4
349
21
5
34
11
7 6
1098
A210
A12
247
143
Ø 4(1)(3)
(2)
19
(4)
3675
102
105
29
924
40
32
63
3111
216
111
32
8
22
5
12
4
349
21
5
34
11
7 6
1098
A210
A12
247
143
Ø 4(1)(3)
(2)
19
(4)
Zelio Relay - plug-in relaysRUM universal relays
Dimensions
1
2
3
4
5
6
7
8
9
10
36
Dimensions (continued)Sockets (continued)RUZ SF3M
36104
294627
924
63
219
318
117
223
322
121
246
A2B
A1A
345
144
(1)
(3)
(2)
(4)
(1) Relays(2) Protection module(3) Maintaining clamp(4) 2 bus jumpersMetal maintaining clamps and plastic legendsRUZ C200 Mounting
0,
59,6
35
108
RUZ L420
12
14,2
32
Bus jumperRUZ S2 Mounting on sockets with separate contacts (view from below)
Example of bus jumper mounting on sockets
(2)(2)
(1)(1)
(1) 2 bus jumpers (polarity A2)(2) 2 bus jumpers (polarity A1)
3,3
8,5
35,4
322,3
3,3
8,5
35,4
322,3
Dimensions (continued) Zelio Relay - plug-in relaysRUM universal relays
Characteristics :page 31
References :pages 33 and 34
Dimensions :page 35
Schemes :page 37
Setting-up :page 39
Characteristics :page 31
References :pages 33 and 34
Dimensions :page 35
Schemes :page 37
Setting-up :page 39
1
2
3
4
5
6
7
8
9
10
37
Schemes Zelio Relay - plug-in relaysRUM universal relays
SchemesUniversal relaysRUM p2ABppp RUM C3ppppp RUM F3ABppp
RUM C2ABppp RUM F2ABppp RUM C3ppppp RUM F3ABppp
Symbols shown in blue correspond to Nema marking.SocketsRUZ C2M RUZ C3M RUZ SC2M RUZ SC3M
24
6
A27
A12
111
218
A27
22
5
12
4
1
4
2
3
8
5
7
6
14
3
32
8
34
9
A210
A12
111
3111
216
A210
24
7
22
5
14
3
12
4
1
6
2
5
34
1110
7
98
225
111
124
624 8
21
314
A27
A12
1
4
2
3
8
5
7
6
3111
216
111
328
225
124
349
247
143
1
6
2
5
34
1110
7
98
A210
A12
Symbols shown in blue correspond to Nema marking.
RUZ SF3M
219
318
117
223
322
121
246
345
144
A2B
A1A
Symbols shown in blue correspond to Nema marking.
1211
14 2221
24 A2
A1
1211
14 2221
24 A2
A1
1211
14 2221
24 3231
34 A2
A1
1211
14 2221
24 3231
34 A2
A1
1211
14 2221
243231
34 A2
A1
1211
14 2221
243231
34 A2
A1
3
7
1
6
2
4 5
A1 A2
2111
14 24
2212
+
3
7
1
6
2
4 5
A1 A2
2111
14 24
2212
+
1
124
147
11
3
226
249
21A
A1
B
A2(+) ( )
1
124
147
11
3
226
249
21A
A1
B
A2(+) ( )
4
3 9
2
1 11
10
56
7
A1 A2
14 34
3111
12 32
22 2421
+
4
3 9
2
1 11
10
56
7
A1 A2
14 34
3111
12 32
22 2421
+
(+)
1
124
147
11
2
325
34
31
3
226
249
21A
A1
B
A2( )(+)
1
124
147
11
2
325
34
31
3
226
249
21A
A1
B
A2( )
1
2
3
4
5
6
7
8
9
10
3
Schemes (continued)Protection modulesRUW 240BD RUW 241P7 RUW 242pp
– A2
+ A1
– A2
+ A1
– A2
+ A1
Zelio Relay - plug-in relaysRUM universal relays
Schemes (continued)
Characteristics :page 31
References :pages 33 and 34
Dimensions :page 35
Schemes :page 37
Setting-up :page 39
Characteristics :page 31
References :pages 33 and 34
Dimensions :page 35
Schemes :page 37
Setting-up :page 39
1
2
3
4
5
6
7
8
9
10
39
Multifunction timer module RUW 101MWProgramming Timing range selection
Function selectionSelection Function Control Function diagram Control scheme
On-delay TimerE
Series control
Monostable with maintained controlWu
Series control
Flashing relay, starting On-delay phaseBi
Series control
Flashing relay, starting Off-delay phaseBp
Series control
Off-delay timerR
Control by external contact (S)
Monostable with pulse controlWs
Control by external contact (S)
Monostable, starting on de-energisationWa
Control by external contact (S)
On-delay TimerEs
Control by external contact (S)
Power off Contact open U : voltage S : external control
Power on Contact closed R : relay RUM ppp t : adjustable time delay
Functionselection
Timing rangeselection
0.1…1 s 0.1…10 s 0.1…1 min 1…10 min 0.1…1 h 1…10 h 0.1…1 day 1…10 days
Functionselection
Timing rangeselection
0.1…1 s 0.1…10 s 0.1…1 min 1…10 min 0.1…1 h 1…10 h 0.1…1 day 1…10 days
t
U
.1/.4
.1/.2t
U
.1/.4
.1/.2 A1
A2
U
R
A1
A2
U
RU
.1/.4
.1/.2t
U
.1/.4
.1/.2t
U
.1/.4
.1/.2t t
U
.1/.4
.1/.2t t
U
.1/.4
.1/.2t t
U
.1/.4
.1/.2t t
S
U
.1/.4
.1/.2t
S
U
.1/.4
.1/.2t
B1
A1
A2
U
R
S
B1
A1
A2
U
R
S
S
U
.1/.4
.1/.2t
S
U
.1/.4
.1/.2t
S
U
.1/.4
.1/.2t
S
U
.1/.4
.1/.2t
S
U
.1/.4
.1/.2t
S
U
.1/.4
.1/.2t
Zelio Relay - plug-in relaysRUM universal relays
Setting-up
1
2
3
4
5
6
7
8
9
10
40
9
7
1066
73
Presentation of the range The RPM power relay range comprises: 1 15 A relays with 1, 2, 3 and 4 C/O contacts.2 Sockets with mixed contact terminals.3 Protection modules (diode, RC circuit or varistor) or 1 timer module. All these
modules are common to all the sockets except for the timer module, which can only be used on the 3-pole or 4-pole sockets.
A metal maintaining clamp for single-contact relays.
Relay description 1 Spring return pushbutton for testing the contacts (green: c, red: a). 2 Mechanical “relay status” indicator.3 Removable lock-down door enabling forced maintaining of the contacts for test
sequences or maintenance purposes. During operation, this lock-down door must always be in the closed position.
4 LED (depending on version) indicating the relay status.5 Removable legend for relay identification.6 Four notches for rail mounting adapter or panel mounting adapter with fixing lugs.7 Five, eight, eleven or fourteen Faston type pins.8 Area by which the product can be easily gripped.9 Mounting adapter enabling direct mounting of the relay on a panel.10 Mounting adapter enabling direct mounting of the relay on a 5 rail.
Socket descriptionSockets with mixed contact terminals (1)
1 Connection by screw clamp terminals. 2 Five, eight, eleven or fourteen female contacts for the relay pins.3 Location for protection modules or the timer module.4 Locating slot for mounting on rail with fixing clip.5 Two or four fixing holes for panel mounting.
(1) The inputs are mixed with the relay's supply, with the outputs being located on the opposite side of the socket.
Zelio Relay - plug-in relays RPM power relays
1060
35
2
1
3
1066
69
2
7
3
56
8
4
1
1066
72 9
1066
74
10
1060
40 1
5
2
3
Outputs
4 Inputs
Relay supply
Characteristics :page 41
References :page 43
Dimensions :page45
Schemes :page 47
Characteristics :page 41
References :page 43
Dimensions :page45
Schemes :page 47
Presentation
1
2
3
4
5
6
7
8
9
10
41
General characteristicsConforming to standards IEC/EN 6110-1 (iss. 2), UL 50, CSA C22-2 n° 14Product certifications UL, CSAAmbient air temperature around the device
Storage °C - 40… + 5Operation °C - 40… + 55
Vibration resistanceconforming to IEC/EN 6006-2-6
In operation 3 gn (10...150 Hz/± 1 mm / 5g/5 cycles)Not operating 5 gn (10...150 Hz/± 1 mm / 5g/5 cycles)
Degree of protection Conforming to IEC/EN 60529 IP 40Shock resistanceconforming to IEC/EN 6006-2-27
Opening 15 gnClosing 15 gn
Protection category RT IMounting position Any
Insulation characteristicsRated insulation voltage (Ui) Conforming to IEC/EN 60947 V 250 (IEC), 300 (UL, CSA)Rated impulse withstand voltage (Uimp) kV 4 (1.2/50 ms)Dielectric strength(rms voltage)
Between coil and contact a V 1550Between poles a V 1550Between contacts a V 1500
Contact characteristicsRelay type RPM 1ppp RPM 2ppp RPM 3ppp RPM 4ppp
Number and type of contacts 1 C/O 2 C/O 3 C/O 4 C/OContact materials AgNiConventional thermal current (Ith)
For ambient temperature y 55 °C
A 15
Rated operational current in utilisation categories AC-1 and DC-1
Conforming to IEC "C" A 15“O” A 7.5
Conforming to UL A 15Switching current Minimum mA 10Switching voltage Maximum V a/c 250 (IEC)
Minimum V 17Nominal load (resistive) A 15 / 250 a V
A 15 / 2 c VSwitching capacity Maximum a VA 3750
c W 420Minimum mW 170
Maximum operating rateIn operating cycles/hour
No-load 1 000Under load 1200
Utilisation coefficient 20 %Mechanical durability In millions of
operating cycles10
Electrical durability In millions of operating cycles
Resistive load 0.1 0.06Inductive load See curves below
Electrical durability of contactsResistive load a
Reduction coefficient for inductive load a (depending on power factor cos j)
Maximum switching capacity on resistive load c
Durability (inductive load) = durability (resistive load) x reduction coefficient.
10520 1 43
3,75
106
107
Dur
abili
ty (N
umbe
r of o
pera
ting
cycl
es)
Switching capacity (kVA)
10520 1 43
3,75
106
107
Dur
abili
ty (N
umbe
r of o
pera
ting
cycl
es)
Switching capacity (kVA)
0,3
0,5
0,61 0,4 0,2
0,4
0,60,
1
Red
uctio
n co
effic
ient
(A)
0,3
0,5
0,61 0,4 0,2
0,4
0,60,
1
Red
uctio
n co
effic
ient
(A)
0,1
1
200 2500 50 100 150
1015
28
Cur
rent
c
Voltage c
0,1
1
200 2500 50 100 150
1015
28
Cur
rent
c
Voltage c
Characteristics Zelio Relay - plug-in relays RPM power relays
1
2
3
4
5
6
7
8
9
10
42
Coil characteristicsRelay type RPM 1ppp RPM 2ppp RPM 3ppp RPM 4ppp
Average consumption a VA 0.9 1.2 1.5 1.5c W 0.7 0.9 1.7 2
Drop-out voltage threshold a u 0.15 Ucc u 0.1 Uc
Operating time(response time)
Between coil energisation and making of the On-delay contact
a ms 20 25 25 20
c ms 20 25 25 20
Between coil de-energisation and making of the Off-delay contact
a ms 20
c ms 20
Control circuit voltage Uc V 12 24 48 110 120 230Relay control voltage codes JD BD ED FD – –
d.c. supply Average resistance at 20 °C ± 10%
RPM 1ppp W 10 750 2600 13 100 – –RPM 2ppp W 160 650 2600 11 000 – –RPM 3ppp W 100 400 2600 600 – –RPM 4ppp W 96 3 1550 7340 – –
Operating voltage limits
Min. V 9.6 19.2 3.4 – –Max. V 13.2 26.4 52. 121 – –
Relay control voltage codes – B7 E7 – F7 P7a.c. supply Average resistance
at 20 °C ± 15%RPM 1ppp W – 160 720 – 4430 15 720RPM 2ppp W – 10 770 – 4430 15 000RPM 3ppp W – 103 770 – 2770 12 000RPM 4ppp W – 4.3 33 – 2220 9120
Operating voltage limits
Min. V – 19.2 3.4 – 96 14Max. V – 26.4 52. – 132 253
Socket characteristicsSocket type RPZ F1 RPZ F2 RPZ F3 RPZ F4Relay types used RPM 1ppp RPM 2ppp RPM 3ppp RPM 4ppp
Protection module types used RXM 02pppRXM 04ppp
RXM 02pppRXM 04ppp
RUW 24ppp RUW 24ppp
Contact terminal arrangement MixedWire connection method Screw clamp terminalsProduct certifications UL, CSA Conforming to standards IEC 6194, e
Electrical characteristicsConventional thermal current (Ith) A 16Maximum operating voltage V 250 (IEC)
Insulation characteristicsBetween adjacent output contacts Vrms 2500Between input and output contacts Vrms 2500Between contacts and 5 rail Vrms 2500
General characteristicsAmbient air temperaturearound the device
Operation °C - 40…+ 55Storage °C - 40…+ 5
Degree of protection Conforming to IEC/EN 60529 IP 20Cabling Solid cable
without cable end
1 conductor 0.5…1.5 mm2 - AWG 20…AWG 16 0.5…2.5 mm2 - AWG 20…AWG 142 conductors 0.5…1.5 mm2 - AWG 20…AWG 16 0.5…2.5 mm2 - AWG 20…AWG 14
Flexible cable with cable end
1 conductor 0.25…1 mm2 - AWG 22…AWG 17 0.25…1.5 mm2 - AWG 22…AWG 162 conductors 0.25…1 mm2 - AWG 22…AWG 17 0.25…1.5 mm2 - AWG 22…AWG 16
Maximum tightening torque / Screw size Nm 1 / M3 screw 1 / M3.5 screwMounting On 35 mm 5 rail / on panelFixing on 5 rail By red plastic clipTerminal referencing IEC, NEMACompatibility with the metal maintaining clamp Yes NoTimer module No YesProtection module RXM 040W, RXM 041pp, RXM 021pp RUW 24pp
Clip-in legends NoWire connection method Screw clamp terminals
Characteristics (continued) Zelio Relay - plug-in relays RPM power relays
Presentation :page 40
Characteristics :page 41
References :page 43
Dimensions :page 45
Schemes :page 47
Presentation :page 40
Characteristics :page 41
References :page 43
Dimensions :page 45
Schemes :page 47
1
2
3
4
5
6
7
8
9
10
43
Power relays without LED (sold in lots of 10)Control circuit voltge
Number and type of contacts - Thermal current (Ith)1 C/O - 15 A 2 C/O - 15 A 3 C/O - 15 A 4 C/O - 15 AUnit reference
Weight Unit reference
Weight Unit reference
Weight Unit reference
Weight
V kg kg kg kgc 12 RPM 11JD 0.026 RPM 21JD 0.036 RPM 31JD 0.054 RPM 41JD 0.071
c 24 RPM 11BD 0.026 RPM 21BD 0.036 RPM 31BD 0.054 RPM 41BD 0.071
c 4 RPM 11ED 0.026 RPM 21ED 0.036 RPM 31ED 0.054 RPM 41ED 0.071
c 110 RPM 11FD 0.026 RPM 21FD 0.036 RPM 31FD 0.054 RPM 41FD 0.071
a 24 RPM 11B7 0.026 RPM 21B7 0.036 RPM 31B7 0.054 RPM 41B7 0.071
a 4 RPM 11E7 0.026 RPM 21E7 0.036 RPM 31E7 0.054 RPM 41E7 0.071
a 120 RPM 11F7 0.026 RPM 21F7 0.036 RPM 31F7 0.054 RPM 41F7 0.071
a 230 RPM 11P7 0.026 RPM 21P7 0.036 RPM 31P7 0.054 RPM 41P7 0.071
Power relays with LED (sold in lots of 10)c 12 RPM 12JD 0.026 RPM 22JD 0.036 RPM 32JD 0.054 RPM 42JD 0.071
c 24 RPM 12BD 0.026 RPM 22BD 0.036 RPM 32BD 0.054 RPM 42BD 0.071
c 4 RPM 12ED 0.026 RPM 22ED 0.036 RPM 32ED 0.054 RPM 42ED 0.071
c 110 RPM 12FD 0.026 RPM 22FD 0.036 RPM 32FD 0.054 RPM 42FD 0.071
a 24 RPM 12B7 0.026 RPM 22B7 0.036 RPM 32B7 0.054 RPM 42B7 0.071
a 4 RPM 12E7 0.026 RPM 22E7 0.036 RPM 32E7 0.054 RPM 42E7 0.071
a 120 RPM 12F7 0.026 RPM 22F7 0.036 RPM 32F7 0.054 RPM 42F7 0.071
a 230 RPM 12P7 0.026 RPM 22P7 0.036 RPM 32P7 0.054 RPM 42P7 0.071
References Zelio Relay - plug-in relays RPM power relays
RPM 41BD
1066
70
RPM 42BD
1066
69
1
2
3
4
5
6
7
8
9
10
44
SocketsContact terminal arrangement
Connection Relay type Sold in lots of
Unit reference
Weightkg
Mixed Screw clamp terminals
RPM 1ppp 10 RPZ F1 0.042RPM 2ppp 10 RPZ F2 0.054RPM 3ppp 10 RPZ F3 0.072
RPM 4ppp 10 RPZ F4 0.094
Protection modulesDescription Voltage Socket type Sold in
lots ofUnit reference
Weight
V kgDiode c 6...250 RPZ F1RPZ F2 20 RXM 040W 0.003
RPZ F3RPZ F4
10 RUW 240BD 0.004
RC circuit a 24...60 RPZ F1RPZ F2 20 RXM 041BN7 0.010
a 110...240 RPZ F1RPZ F2 20 RXM 041FU7 0.010
RPZ F3RPZ F4
10 RUW 241P7 0.004
Varistor a/c 6...24 RPZ F1RPZ F2 20 RXM 021RB 0.030
a/c 24...60 RPZ F1RPZ F2 20 RXM 021BN 0.030
a/c 110...240 RPZ F1RPZ F2 20 RXM 021FP 0.030
a/c 24 RPZ F3RPZ F4
10 RUW 242B7 0.004
a/c 240 RPZ F3RPZ F4
10 RUW 242P7 0.004
Timer module (1)Description Voltage Socket type Reference Weight
V kgMultifunction a/c 24… 240 RPZ F3
RPZ F4RUW 101MW 0.020
AccessoriesDescription For
use withSold in lots of
Unit reference
Weightkg
Metal maintaining clamp(for single-pole relays)
RPZ F1 20 RPZ R235 0.001
Mounting adapters for 5 rail (2) RPM 1ppp 20 RPZ 1DA 0.004RPM 2ppp 20 RXZ E2DA 0.004RPM 3ppp 20 RPZ 3DA 0.004RPM 4ppp 20 RPZ 4DA 0.006
Mounting adapters with fixing lugs for panel RPM 1ppp 20 RPZ 1FA 0.002RPM 2ppp 20 RXZ E2FA 0.002RPM 3ppp 20 RPZ 3FA 0.003RPM 4ppp 20 RPZ 4FA 0.004
Clip-in legends(sheet of 10 legends)
All relays 10 RXZ L520 0.00
(1) See timer module description (selection of functions and time delays) on page 39.(2) Test button becomes inaccessible.
References (continued) Zelio Relay - plug-in relays RPM power relays
Presentation :page 40
Characteristics :page 41
References :page 43
Dimensions :page 45
Schemes :page 47
Presentation :page 40
Characteristics :page 41
References :page 43
Dimensions :page 45
Schemes :page 47
RPZ F2 + relay RPM 22F7
1060
43
RUW 24ppp
1060
44
RPZ 1DA
1060
45
RPZ 3FA
1060
46
1
2
3
4
5
6
7
8
9
10
45
DimensionsPower relaysRPM 1
Common side view RPM2 RPM 3 RPM 4
SocketsRPZ F1 RPZ F2
14
5
12
1
A2
14
A1
13
11
9
31
19
1721
4
71
(1)
(3) (2)
80
40
804
40
44
8
14
5
424
121
A214
A113
41
12
11
9
30 2619
30
4040
4
19
8
76
80 68
4
Ø4,5 x 6
Ø4,5 x 6
(1)
(2)
Common side view RPZ F3 RPZ F4
30
76
804
19
8
(1)
(2)
28
4037
4040
68 4
44
8
24
6
14
542
4
A214
A113
41
12
21
10
11
9
22
2
12
1
Ø4,5 x 6
Ø4,5 x 6364650
4040
68 4
14
5
24
6
34
7
44
8
A2
14
A1
13
41
12
31
11
21
10
11
9
12
1
22
2
32
3
42
4
Ø4,5 x 6
Ø4,5 x 6
(1) Relays(2) Protection module(3) Maintaining clamp
8 39 7
7,1
64,6
44,
68 39 7
7,1
64,6
44,
6 3127
1010
4,6 4,6 4,6
3127
1010
4,6 4,6 4,6
41 1010 10
27
4,6 4,6 4,6 4,6
41 1010 10
27
4,6 4,6 4,6 4,6
Dimensions Zelio Relay - plug-in relays RPM power relays
763 14
40
27
4,7
6,5
65
3,5
2,62,6
27
21 1014,2
4,6 4,6
1
2
3
4
5
6
7
8
9
10
46
Dimensions (continued)Mounting adapters for 5 railRPZ 1DA RXZ E2DA RPZ 3DA RPZ 4DA
Mounting adapters with fixing lugs for panelRPZ 1FA RXZ E2FA RPZ 3FA RPZ 4FA
MountingMounting adapters for 5 rail (1) Mounting adapters with fixing lugs for panel
(1) Test button becomes inaccessible
23 24
49,5
2,523 24
49,5
2,5
384
24
23
483
384
24
23
483 3423
502,
5 3423
502,
5
4420
502,
5 4420
502,
5
3843
3,5 5
16,516
3843
3,5 5
16,516
38
3,5 4
19
43
24
38
3,5 4
19
43
24
38
19
3,5 4
43
34
38
19
3,5 4
43
34
16 3,5 4
3843
44
16 3,5 4
3843
44
Dimensions (continued) Zelio Relay - plug-in relays RPM power relays
Presentation :page 40
Characteristics :page 41
References :page 43
Dimensions :page 45
Schemes :page 47
Presentation :page 40
Characteristics :page 41
References :page 43
Dimensions :page 45
Schemes :page 47
1
2
3
4
5
6
7
8
9
10
47
SchemesPower relaysRPM 1ppp RPM 2ppp RPM 3ppp RPM 4ppp
Symbols shown in blue correspond to Nema marking.
Sockets RPZ F1 RPZ F2 RPZ F3 RPZ F4
145
121
119
A214
A113
INPUT
448
145
424
121
4112A214
119
A113
4112
2110
119
A214
A113
448
246
145
424
222
121
A214
A113
4112
3111
2110
119
448
347
246
145
424
323
222
121
Symbols shown in blue correspond to Nema marking.
Protection modules RXM 040W, RUW 240BD RXM 041ppp, RUW 241P7 RXM 021ppp, RUW 242pp
– A2
+ A1
– A2
+ A1
– A2
+ A1
1
12
5
14
9
1113
A1
14
A2
(+) ( )
A2
A1
111412
1
12
5
14
9
1113
A1
14
A2
(+) ( )
A2
A1
111412
1
125
149
11
4
228
2412
2113
A1
14
A2
(+) ( )
A2
A1
212422
111412
1
125
149
11
4
228
2412
2113
A1
14
A2
(+) ( )
A2
A1
212422
111412
1
12
5
14
9
11
2
22
6
24
10
21
4
42
8
44
12
4113
A1
14
A2
(+) ( )
A2
A1
212422
414442
111412
1
12
5
14
9
11
2
22
6
24
10
21
4
42
8
44
12
4113
A1
14
A2
(+) ( )
A2
A1
212422
414442
111412
(+)
1
12
5
14
9
11
2
22
6
24
10
21
3
32
7
34
11
31
4
42
8
44
12
4113
A1
14
A2
( )
A2
A1
212422
313432
414442
111412
(+)
1
12
5
14
9
11
2
22
6
24
10
21
3
32
7
34
11
31
4
42
8
44
12
4113
A1
14
A2
( )
A2
A1
212422
313432
414442
111412
Schemes Zelio Relay - plug-in relays RPM power relays
1
2
3
4
5
6
7
8
9
10
4
Zelio Relay - plug-in relays
RelaysContact typesSymbol Configuration EU USA
Make contact (Normally Open)
NO SPST-NODPST-NOnPST-NO (1)
Break contact (Normally Closed)
NC SPST-NCDPST-NCnPST-NC (1)
Changeover Contact CO SPDTDPDTnPDT (1)
Utilisation categoriesCategory Type of current Applications
AC-1 a single-phasea 3-phase
Resistive or slightly inductive loads.
AC-3 a 3-phase Starting and braking of squirrel cage motors; reversing direction of rotation only after stopping of motor.
AC-4 a 3-phase Starting of squirrel cage motors, inching. Plugging, reversing direction of rotation.
DC-1 c Resistive or slightly inductive loads (2).
AC-14 a single-phase Control of electromagnetic loads (< 72 VA), auxiliary control relays, power contactors, electromagnetic solenoid valves and electromagnets.
AC-15 a single-phase Control of electromagnetic loads (> 72 VA), auxiliary control relays, power contactors, electromagnetic solenoid valves and electromagnets.
DC-13 c Control of electromagnetic loads, auxiliary control relays, power contactors, magnetic solenoid valves and electromagnets.
Protection categoriesCategory Explanation Condition
RT 0 Unenclosed relay Relay not provided with a protective case.
RT I Dust protected relay
Relay provided with a case which protects its mechanism from dust.
RT II Flux-proof relay Relay capable of being automatically soldered without allowing the migration of solder fluxes beyond the intended areas.
RT III Wash-tight relay Relay capable of being automatically soldered and then washed to remove flux residues without risk of ingress of flux or washing solvents.
RT IV Sealed relay Relay provided with a case which has no venting to the outside atmosphere.
RT V Hermetically sealed relay
Sealed relay having an enhanced level of sealing.
(1) n = number of contacts.(2) The switchable voltage can be doubled, for an equal current, by connecting two contacts in
series.
Technical presentation
1
2
3
4
5
6
7
8
9
10
49
Zelio Relay - plug-in relays
Protection modulesWhenever an inductive load is de-energised (coil of a relay or of a contactor), an overvoltage appears at its terminals. This voltage peak can reach several thousand volts and a frequency of several MHz.It is likely to disturb the operation of automation systems which contain electronic devices.Protection modules are used to reduce the voltage peak on de-energisation and they therefore limit the energy of interference signals to a level that will not disturb surrounding coils and electronic devices.
These modules are used to avoid: electromagnetic compatibility problems, the deterioration of contact materials,the destruction of insulation due to overvoltage,the destruction of electronic components.
vvvv
Diode protection module (with or without LED)
Coil voltage with diode protection module (c only)
Advantagesaccumulation of energy allowing current flow in the same direction,absence of any voltage peaks at the coil terminals,low cost.
Disadvantages
bvvv
bincrease in relay drop-out time (3 to 4 times the usual time),no polarity protection,de-energisation of the relay.
vvv
Protection module with varistor
Coil voltage with varistor protection module (a and c)
Advantagescan be used with a and c supply,voltage peak limited to about 2 Un,little effect on relay drop-out time.
Disadvantages
bvvv
bno modification of coil’s own oscillating frequency,limitation of switching frequency.
vv
Protection module with RC circuit
Coil voltage with RC circuit protection module (a only)
S1 = S2 = Energy released
Advantagescoil oscillating frequency reduced to about 150 Hz,voltage peak limited to 3 Un,little effect on relay drop-out time.
Disadvantages
bvvv
bno protection for low voltages.v
U
t
Supply voltage
Energy released
BreakU
t
Supply voltage
Energy released
Break
U
t
Energyreleased
Break
Lim
itatio
n of
vol
tage
pe
aks
U
t
Energyreleased
Break
Lim
itatio
n of
vol
tage
pe
aks
S1
U1
U2
U
t
Break
S2 (with RC)
S1
U1
U2
U
t
Break
S2 (with RC)
Presentation
1
2
3
4
5
6
7
8
9
10
50
Solid state interface modules
Output Input and output Very low level switching
Input Output
17.5 12 17.5 9.5 9.5/17.5
1 N/O 2 N/O 1 C/O 1 N/C + 1 N/O
1 N/O 1 C/O –
12 A 5 A – 5 A
c 24 V z 24 V, 4 V a 115…127 V a 110 V
c 24 V c 5, 24, 4 V a 115…127/50 Hz a 120…127/60 Hz a 230…240/50 Hz a 230…240/60 Hz
c 24 V
Mechanical for contacts and/or LED for control
LED for control
ABR 1S ABR 2S ABR 2pB312B ABS 2E ABS 2S
56 62 62 6
Applications Electromechanical interface modules
Functions Input
Width (mm) 17.5 9.5
Contact arrangement 1 N/O 2 N/O 1 C/O
1 N/O
Thermal current –
Control voltages c 110…127 V z 24 V, 4 V a 115…127 V a 230/240 V
c 24 V, 4 V a 115…127/50 Hz a 115…127/60 Hz a 230…240/50-60 Hz
Indication Mechanical for contacts and/or LED for control
LED for control
References ABR 1E ABR 2E
Pages 56 62
Selection guide Interfaces Interfaces for discrete signals
1
2
3
4
5
6
7
8
9
10
51
Solid state interface modules
Output Input and output Very low level switching
Input Output
17.5 12 17.5 9.5 9.5/17.5
1 N/O 2 N/O 1 C/O 1 N/C + 1 N/O
1 N/O 1 C/O –
12 A 5 A – 5 A
c 24 V z 24 V, 4 V a 115…127 V a 110 V
c 24 V c 5, 24, 4 V a 115…127/50 Hz a 120…127/60 Hz a 230…240/50 Hz a 230…240/60 Hz
c 24 V
Mechanical for contacts and/or LED for control
LED for control
ABR 1S ABR 2S ABR 2pB312B ABS 2E ABS 2S
56 62 62 6
Applications Electromechanical interface modules
Functions Input
Width (mm) 17.5 9.5
Contact arrangement 1 N/O 2 N/O 1 C/O
1 N/O
Thermal current –
Control voltages c 110…127 V z 24 V, 4 V a 115…127 V a 230/240 V
c 24 V, 4 V a 115…127/50 Hz a 115…127/60 Hz a 230…240/50-60 Hz
Indication Mechanical for contacts and/or LED for control
LED for control
References ABR 1E ABR 2E
Pages 56 62
1
2
3
4
5
6
7
8
9
10
52
Interfaces For discrete signalsElectromechanical interface modules
ABR-1 electromechanical interface modules are supplied in the form of compact modules, 17.5 mm wide.They are designed for interfacing discrete digital control signals exchanged within an automated system between the processing unit (PLC, numerical controller, etc) and the other components (contactors, solenoid valves, indicator lamps, proximity sensors, etc).These products are based on contactor technology and are notable for their excellent adaptation to industrial environments, ensured by the fact that they conform to the most recent IEC 947-5-1 standards.
CompositionThe ABR-1 range comprises 2 families :
Input interfaces Input interfaces are designed for switching input signals to the processor and are characterized by their high degree of contact reliability : less than 1 fault per 100 million operating cycles at c 17 V, 5 mA.The switching level is sufficiently high to ensure that the interfaces can directly control most contactors and indicator lamps.
Output interfaces Output interfaces are designed for the control of preactuators (contactors, solenoid valves, etc) for signalling devices (indicators lamps, audible warnings, etc). They are characterized by a high switching capacity and an average durability 5 times greater than that of traditional interface modules which incorporate standard relays.
1 Override contacts by pressing button (not holding it down) for a simple and quick test during setting up or maintenance operations on the installation
2 Green indicator showing the mechanical position of the contacts3 LED indicating the control signal state4 Channel identification : 5 individual characters for AB1-R/G or one AB1-SA2
marker tag5 Connection by screw clamp terminal enabling easy attachment of 2 wires per
terminal. The layout of the connection terminals for both families (input and output) is designed for rational wiring and a clear separation between the incoming (processing) and outgoing (power and process control) circuits.
162
64
5
214
3
162
64
5
214
3
162
65
5
3
412
162
65
5
3
412
Presentation
Presentation:page 52
Characteristics:page 53
Curves:page 55
Dimensions, schemes:page 57
1
2
3
4
5
6
7
8
9
10
53
Interfaces For discrete signalsElectromechanical interface modules
Examples of applications with PLCs
(1) Essential on inductive loads (can be replaced with peak limiter ).
–/
+/
–
+
A2
A1
A2
A1
A2
A1
A2
A1
PushbuttonsSeries contacts
2-wiresensors
3-wiresensors
PushbuttonsSeries contacts
2-wiresensors
PLCPositive logic discrete inputs
–/
+/
–
+
A2
A1
A2
A1
A2
A1
A2
A1
PushbuttonsSeries contacts
2-wiresensors
3-wiresensors
PushbuttonsSeries contacts
2-wiresensors
PLCPositive logic discrete inputs
–/
+/
–
+
24...125 V ...240 V
A1
A2
(1) (1)
A1
A2
A1
A2
PLCPositive logic transistor (or relay) outputs
–/
+/
–
+
24...125 V ...240 V
A1
A2
(1) (1)
A1
A2
A1
A2
PLCPositive logic transistor (or relay) outputs
Environment
Conforming to standards IEC 947-5-1Product certifications UL, CSA, BV, LROS, DNVDegree of protection Conforming to IEC 529
(protection against direct contact)IP 00
Protective treatment “TC”Flame resistance Conforming to IEC 695-2-1 Incandescent wire °C 50
Conforming to UL 94 V0Shock resistance Conforming to IEC 6-2-27 Semi-sinusoidal waves 11 ms 50 gnVibration resistance Conforming to IEC 6-2-6 10…55 Hz 6 gnResistance to electrostatic charges
Conforming to IEC 01-2 Level 3 kV
Resistance to rapid transients
Conforming to IEC 01-4 On power supply kV 2On I/O kV 1
Resistance to shock waves
Conforming to IEC 255-4 Waveform 1.2/50 ms ; 0.5 J
U ≤ 50 V kV 0.5U > 50 V kV 2.5
Cross-sections which may be connected
Flexible cable with no cable end 1 or 2-wire mm2 0.6…2.5Flexible cable with cable end 1 or 2-wire mm2 0.34…2.5Rigid cable 1-wire mm2 0.27…4
2-wire mm2 0.27…2.5Operating position AnyAmbient air temperature around the device
Unrestricted operation °C - 5…+ 40Permissible at Un °C - 20…+ 60Storage °C - 40…+ 70
Operating altitude m ≤ 3000Installation category Conforming to IEC 947-1 IIDegree of pollution Conforming to IEC 947-5-1 3Mounting Standard rails 5 1 4
Environment
Conforming to standards IEC 947-5-1Product certifications UL, CSA, BV, LROS, DNVDegree of protection Conforming to IEC 529
(protection against direct contact)IP 00
Protective treatment “TC”Flame resistance Conforming to IEC 695-2-1 Incandescent wire °C 50
Conforming to UL 94 V0Shock resistance Conforming to IEC 6-2-27 Semi-sinusoidal waves 11 ms 50 gnVibration resistance Conforming to IEC 6-2-6 10…55 Hz 6 gnResistance to electrostatic charges
Conforming to IEC 01-2 Level 3 kV
Resistance to rapid transients
Conforming to IEC 01-4 On power supply kV 2On I/O kV 1
Resistance to shock waves
Conforming to IEC 255-4 Waveform 1.2/50 ms ; 0.5 J
U ≤ 50 V kV 0.5U > 50 V kV 2.5
Cross-sections which may be connected
Flexible cable with no cable end 1 or 2-wire mm2 0.6…2.5Flexible cable with cable end 1 or 2-wire mm2 0.34…2.5Rigid cable 1-wire mm2 0.27…4
2-wire mm2 0.27…2.5Operating position AnyAmbient air temperature around the device
Unrestricted operation °C - 5…+ 40Permissible at Un °C - 20…+ 60Storage °C - 40…+ 70
Operating altitude m ≤ 3000Installation category Conforming to IEC 947-1 IIDegree of pollution Conforming to IEC 947-5-1 3Mounting Standard rails 5 1 4
Characteristics
1
2
3
4
5
6
7
8
9
10
54
Interfaces For discrete signalsElectromechanical interface modules
Control circuit characteristics (40°C ambient temperature)Type of interface ABR
1Sp02BABR 1ppp8B
ABR 1ppp8E
ABR 1Ep12F
ABR 1ppp1F
ABR 1Ep11M
ABR 1Ep01M
Rated voltage (Uc) V c 24 z 24 z 4 c 110...127
a 115...127
a 230...240
a 230...240
Current frequency Hz – 50/60 50/60 – 50/60 50/60 50/60Energization threshold (at ± 5 %) V 15 16.5 34 75 6 170 164Maximum operating voltage c / a V 30 30 53 140 140 264 264Maximum drop-out (at ± 5 %) voltage (Uo) c / a V 3.2 3. .5 16 34 6 7Maximum current (Un) c / a mA 62 62/55 36/32 15 7 5.5Minimum holding current c / a mA 6.6 4.9/5.2 4.7/5.4 1.5 2.4 2 1.5Maximum dissipated power 50 Hz/60 Hz W 1.5 1.5 1.5 1.5 1.5 1.5 1.5Disappearance of voltage maximum time up to which contact is maintained
ms 3 10 10 6 5 6
Display of control circuit by LED No Yes Yes Yes Yes Yes NoBuilt-in protection reversed polarity Yes Yes Yes Yes – – –
Contact characteristicsType of interface ABR 1Epppp ABR 1Spppp
Maximum switching voltage a V 252 252 c V 125 125
Maximum rated operating voltage Ue
Conforming to IEC 947-5-1 a V 230 230 c V 125 125
Operating current frequency Hz 50/60 50/60Thermal current Ith Conforming to IEC 947-1 A 2 12Rated operating current (Ie) per 1 million operating cycles
Conforming to IEC 947-5-1 Ue : a 230 V
AC12 A 2 4AC13 A 1 1AC14 A 1 1AC15 A 1 1
Conforming to IEC 947-5-1 Ue : c 24 V
DC12 A 2 5DC13 A 1 1
Minimum switching capacity mA 3 3Minimum switching voltage V 17 17Protection against short-circuits
For Ik ≤ 2.5 kA (a) and ≤ 100 A (c) Type and value of recommended fuse
A gG/gF : 16 gG/gF : 16
Low power switching reliability of contacts (17 V - 5 mA)
Number of faults per “n” million operating cycles
10- 10-
Other characteristicsOperating time at Un and at 20 °C
Between energization of coil and closing of N/O contact
ms ≤ 12
Between energization of coil and opening of N/C contact
ms ≤ 12
Between de-energization of coil and opening of N/O contact
ms ≤ 12
Between de-energization of coil and closing of N/C contact
ms ≤ 12
Duration of bounce ms ≤ 3Contact bridging times between contact “N/C” and “N/O”
Maximum make before break or break before make time
ms 1
Maximum operating rate
At no-load Hz 6At Ie Hz 0.5
Mechanical durability in millions of operating cycles
ABR-1 (1 N/O or 2 N/O) ≥ 20 millionABR-1 (1 C/O or 1 N/C + 1 N/O) ≥ 10 million
Rated isolation voltage Conforming to IEC 947-1 V 250Conforming to VDE 0110 group C V 250
Insulation test voltage for 1 min.
Between coil circuit and contact circuits kV 4Between wired interface and earth kV 2.5Between independent contacts kV 1.5
Characteristics (continued)
Presentation:page 52
Characteristics:page 53
Curves:page 55
Dimensions, schemes:page 57
1
2
3
4
5
6
7
8
9
10
55
Interfaces For discrete signalsElectromechanical interface modules
Electrical durability of contactsTest conditions : in accordance with standard IEC 947-5-1 set up for rated control voltage, operating rate : 100 cycles/hour. (0.5 Hz).
a.c. loads
AC-12 : control of resistive loads and isolated solid state loads via optocoupler cos j ≥ 0.9
AC-13 : control of isolated solid state loads via transformer cos j ≥ 0.65
AC-14 : control of weak electromagnetic loads of electromagnets ≤ 72 VAmake: cos j = 0.3break: cos j = 0.3AC-15 : control of electromagnetic loads of electromagnets > 72 VAmake: cos j = 0.7break: cos j = 0.4
1 24 V2 4 V3 127 V4 230 V
d.c. loads
1 24 V2 4 V3 127 V
DC-12 : control of resistive loads and isolated solid state loads via optocoupler L/R ≤ 1 ms
DC-13 : control of electromagnets L/R ≤ 2 x (Ue x Ie) in ms.Ue: rated operating voltageIe: rated operating current
5
4
3
2
1
1 2 3 4 5(A)
6
0
0
34
2
6
Operating cycles in millions
5
4
3
2
1
1 2 3 4 5(A)
6
0
0
34
2
6
Operating cycles in millions
5
4
3
2
1
1 2 3 4 5(A)
6
0
0
6
3
1
4
2
Operating cycles in millions
5
4
3
2
1
1 2 3 4 5(A)
6
0
0
6
3
1
4
2
Operating cycles in millions
2
1
0,5 1 1,5 2 2,5
(A)
3
0
0
3
1
2
3
4
Operating cycles in millions
2
1
0,5 1 1,5 2 2,5
(A)
3
0
0
3
1
2
3
4
Operating cycles in millions
5
4
3
2
1
0
1 2 3 4 5
(A)
2
3
6
60
1
Operating cycles in millions
5
4
3
2
1
0
1 2 3 4 5
(A)
2
3
6
60
1
Operating cycles in millions
2
1
0,5 1 1,5 2 2,5
(A)
3
0
0
3
3
1
2
Operating cycles in millions
2
1
0,5 1 1,5 2 2,5
(A)
3
0
0
3
3
1
2
Operating cycles in millions
Curves
1
2
3
4
5
6
7
8
9
10
56
Interfaces For discrete signalsElectromechanical interface modulesControl circuit : a.c. or d.c.
Input interface modules (1) (17.5 mm pitch)Display Composition Control circuit Enclosure
colourReference Weight
V kgMechanical (2) 1 N/O a 230/240 Grey ABR 1E101M 0.090
1 C/O a 230/240 Grey ABR 1E301M 0.090Mechanical (2) + LED (3)
1 N/O z 24 Grey ABR 1E118B 0.095z 4 Grey ABR 1E118E 0.095c 110...127 (4) Grey ABR 1E112F 0.095a 115...127 Grey ABR 1E111F 0.095a 230/240 Grey ABR 1E111M 0.095
2 N/O z 24 Grey ABR 1E418B 0.095z 4 Grey ABR 1E418E 0.095c 110...127(4) Grey ABR 1E412F 0.095a 115...127 Grey ABR 1E411F 0.095a 230/240 Grey ABR 1E411M 0.095
1 C/O z 24 Grey ABR 1E318B 0.095z 4 Grey ABR 1E318E 0.095c 110...127(4) Grey ABR 1E312F 0.095a 115...127 Grey ABR 1E311F 0.095a 230/240 Grey ABR 1E311M 0.095
Output terminals-relays (1) (17.5 mm pitch)Display Composition Control circuit Enclosure
colourReference Weight
V kgMechanical (2) 1 N/O c 24 Grey ABR 1S102B 0.090
2 N/O c 24 Grey ABR 1S402B 0.0901 C/O c 24 Grey ABR 1S302B 0.0901 N/C + 1 N/O c 24 Grey ABR 1S602B 0.090
Mechanical (2) + LED (3)
1 N/O z 24 Grey ABR 1S118B 0.095z 4 Grey ABR 1S118E 0.095a 115...127 Grey ABR 1S111F 0.095
2 N/O z 24 Grey ABR 1S418B 0.095z 4 Grey ABR 1S418E 0.095a 110 Grey ABR 1S411F 0.095
1 C/O z 24 Grey ABR 1S318B 0.095z 4 Grey ABR 1S318E 0.095a 110 Grey ABR 1S311F 0.095
1 N/C + 1 N/O z 24 Grey ABR 1S618B 0.095z 4 Grey ABR 1S618E 0.095a 110 Grey ABR 1S611F 0.095
Commoning linksDescription For common Colour Distance
between cable ends
Reference Weight
cm kgCommoning links in modules 8 x 1 mm2
Coil White 12 ABF C08R12W 0.0202 ABF C08R02W 0.010
a Red 12 ABF C08R12R 0.0202 ABF C08R02R 0.010
c Blue 12 ABF C08R12B 0.0202 ABF C08R02B 0.010
(1) Connection by screw-clamp.(2) By green mechanical indicator light for contact(s) activated electrically or mechanically by
pressing the test button. (3) By green LED illuminated when control signal is present.(4) With polarization (+ on A1, - on A2).
162
64
ABR 1E101M
162
64
ABR 1E101M
12
15
ABR 1E318B
12
15
ABR 1E318B
162
65
ABR 1S102B
162
65
ABR 1S102B
162
73
ABF C08Rppp
162
73
ABF C08Rppp
Presentation:page 52
Characteristics:page 53
Curves:page 55
Dimensions, schemes:page 57
Presentation:page 52
Characteristics:page 53
Curves:page 55
Dimensions, schemes:page 57
References
1
2
3
4
5
6
7
8
9
10
57
Interfaces For discrete signalsElectromechanical interface modules
DimensionsABR 1E ABR 1S
Schemesc 24 V or a 230 V interfaces with mechanical indication1 N/O 1 C/O 2 N/O 1 N/C + 1 N/O
z 24 V or z 48 V interfaces with mechanical indication + LED1 N/O 1 C/O 2 N/O 1 N/C + 1 N/O
c / a 110 V or a 230 V interfaces with mechanical indication + LED1 N/O 1 C/O 2 N/O 1 N/C + 1 N/O
78
75
70,517,5
74
63
78
75
70,517,5
74
63
78
75
70,517,5
74
63
78
75
70,517,5
74
63
A2
1314
A1
A2
1314
A1
1114
12
A2 A1
1114
12
A2 A1
1314
2324
A2
A1
1314
2324
A2
A1
2324
1112
A2
A1
2324
1112
A2
A1
A1
1314
A2
A1
1314
A2
1114
12
A2
A1
1114
12
A2
A1
1314
2324
A2 A1
1314
2324
A2 A1
2324
1112
A1
A2
2324
1112
A1
A2
1314
A1
(+)
A2
1314
A1
(+)
A2
1114
12
A1
(+)
A2
1114
12
A1
(+)
A2
1314
2324
A1
(+)
A2
1314
2324
A1
(+)
A2
2324
1112
A1
(+)
A2
2324
1112
A1
(+)
A2
Dimensions, schemes
1
2
3
4
5
6
7
8
9
10
5
Interfaces For discrete signalsSlim electromechanical interface modules
ABR-2 electromechanical interface modules complement the ABR-1 range.They are characterised by micro relay technology which allows reduced dimensions and very low switching levels (TTL, HCMOS, analogue signals).The ABR-2 family is in the form of slim compact modules, 9.5 mm wide for input interface modules, 12 mm wide for output interface modules and 17.5 mm wide for very low level switching products.
DescriptionThe ABR-2 comprises 3 families :
Input interfaces (9.5 mm pitch) Input interfaces are designed for switching input signals to a processor and are characterized by their high degree of contact reliability : less than 1 fault per 100 million operating cycles at c 17 V, 5 mA.An assured immunity to current leakages ≤ 2 mA, and a wide coil voltage range (0.7 to 1.25 Un).
Output interfaces (12 mm pitch) Output interfaces are designed for the control of preactuators (contactors, solenoid valves, etc) for signalling devices (indicators lamps, audible warnings etc). They are characterized by a high switching capacity and an assured immunity to current leakages £ 2 mA. A lower cost version without LED signalling is available.2 mA. A lower cost version without LED signalling is available.
Low level switching input and output interfaces (17.5 mm pitch) with 1 C/O contact. These interfaces are designed for switching logic (TTL or HCMOS) and analogue signals.Warning : never switch inductive loads with this type of interface.
The front panel of the ABR-2 electromechanical interface module comprises :1 LED indicating the control signal state2 Channel identification : 5 individual characters for AB1-R/G or 1 AB1-SA2
marker tag3 Connection by screw clamp terminal enabling easy attachment of 2 wires per
terminal. The layout of the connection terminals for both families (input and output) is designed for rational wiring and a clear separation between the incoming (processing) and outgoing (power and process control) circuits.
3
2
1
3
2
1
3
2
1
3
2
1
ABR-2SB312B
ABR2SB312B-PRO-3-B
3
2
1
ABR-2SB312B
ABR2SB312B-PRO-3-B
3
2
1
Presentation:page 5
Characteristics:page 59
Curves:page 61
References:page 62
Dimensions, schemes:page 63
Presentation:page 5
Characteristics:page 59
Curves:page 61
References:page 62
Dimensions, schemes:page 63
Presentation
1
2
3
4
5
6
7
8
9
10
59
Interfaces For discrete signalsSlim electromechanical interface modules
Examples of applications with PLCs
(1) Essential on inductive loads (can be replaced with peak limiter ).
–/
+/
+/
13 14 13 14 13 14
A1
A2
A1
A2
A1
A2
PLCPositive logic discrete inputs
PushbuttonsSeries contacts
2-wiresensors
3-wiresensors
ABR 2Epppp
Processpowersupply
Processingpowersupply
–/
+/
+/
13 14 13 14 13 14
A1
A2
A1
A2
A1
A2
PLCPositive logic discrete inputs
PushbuttonsSeries contacts
2-wiresensors
3-wiresensors
ABR 2Epppp
Processpowersupply
Processingpowersupply
–
+
–
+A
1
A2
(1) (1)
C1
A1
A2
A1
A2
13 14 13 14 13 14
A1
A2
12 14
C2
OV
11
PLCPositive logic transistor (or relay) outputs
PLCAnalogue inputs
Channel X
Analogue sensors
ABR 2Spppp ABR 2SB12B
–
+
–
+A
1
A2
(1) (1)
C1
A1
A2
A1
A2
13 14 13 14 13 14
A1
A2
12 14
C2
OV
11
PLCPositive logic transistor (or relay) outputs
PLCAnalogue inputs
Channel X
Analogue sensors
ABR 2Spppp ABR 2SB12B
Environment
Conforming to standards IEC 947-5-1Product certifications UL, CSA, BV, LROS, DNVDegree of protection Conforming to IEC 529
(protection against direct contact)IP 20
Protective treatment “TC”Flame resistance Conforming to IEC 695-2-1 Incandescent wire °C 960
Conforming to UL 94 V0Shock resistance Conforming to IEC 6-2-27 Semi-sinusoidal waves 11 ms 30 gnVibration resistance Conforming to IEC 6-2-6 10…150 Hz 3 gnResistance to electrostatic discharges
Conforming to IEC 01-2 Level 3 kV
Resistance to electromagnetic fields
Conforming to IEC 01-3 Level 3 ; 27…1000 MHz V/m 10
Resistance to rapid transients
Conforming to IEC 01-4 Level 3
On power supply kV 2On I/O kV 1
Resistance to shock waves
Conforming to IEC 947-1 Waveform 1.2/50 ms ; 0.5 J
U < 50 V kV 0.5U < 150 V kV 1.5U < 300 V kV 2.5
Cross-sections which may be connected
Flexible cable with no cable end 1 or 2-wire mm2 0.6…2.5Flexible cable with cable end 1 or 2-wire mm2 0.34…2.5Rigid cable 1-wire mm2 0.27…4
Operating position AnyAmbient air temperature Unrestricted operation °C - 5…+ 40
Operation from 0.5...1.1 Us (assigned voltage)
°C - 5…+ 55
Operation restricted to Us (assigned voltage)
°C - 25…+ 70 (2)
Storage °C - 40…+ 0Operating altitude m ≤ 3000Installation category Conforming to IEC 947-1 IIDegree of pollution Conforming to IEC 947-1 2Mounting Standard rails 5 1 4(2) Leave space of 8 mm between ABR-2S1ppp for an ambient temperature ≥ 55 °C
Environment
Conforming to standards IEC 947-5-1Product certifications UL, CSA, BV, LROS, DNVDegree of protection Conforming to IEC 529
(protection against direct contact)IP 20
Protective treatment “TC”Flame resistance Conforming to IEC 695-2-1 Incandescent wire °C 960
Conforming to UL 94 V0Shock resistance Conforming to IEC 6-2-27 Semi-sinusoidal waves 11 ms 30 gnVibration resistance Conforming to IEC 6-2-6 10…150 Hz 3 gnResistance to electrostatic discharges
Conforming to IEC 01-2 Level 3 kV
Resistance to electromagnetic fields
Conforming to IEC 01-3 Level 3 ; 27…1000 MHz V/m 10
Resistance to rapid transients
Conforming to IEC 01-4 Level 3
On power supply kV 2On I/O kV 1
Resistance to shock waves
Conforming to IEC 947-1 Waveform 1.2/50 ms ; 0.5 J
U < 50 V kV 0.5U < 150 V kV 1.5U < 300 V kV 2.5
Cross-sections which may be connected
Flexible cable with no cable end 1 or 2-wire mm2 0.6…2.5Flexible cable with cable end 1 or 2-wire mm2 0.34…2.5Rigid cable 1-wire mm2 0.27…4
Operating position AnyAmbient air temperature Unrestricted operation °C - 5…+ 40
Operation from 0.5...1.1 Us (assigned voltage)
°C - 5…+ 55
Operation restricted to Us (assigned voltage)
°C - 25…+ 70 (2)
Storage °C - 40…+ 0Operating altitude m ≤ 3000Installation category Conforming to IEC 947-1 IIDegree of pollution Conforming to IEC 947-1 2Mounting Standard rails 5 1 4(2) Leave space of 8 mm between ABR-2S1ppp for an ambient temperature ≥ 55 °C
Characteristics
1
2
3
4
5
6
7
8
9
10
60
Interfaces For discrete signalsSlim electromechanical interface modules
Control circuit characteristics (40°C ambient temperature)Type of interface ABR
2E112BABR 2E112E
ABR 2E115F
ABR 2E116F
ABR 2E111M
ABR 2S112B
ABR 2S102B
ABR 2pB312B (1)
Rated voltage (Us) V c 24 c 4 z 115…127
z 120...127
a 230...240
c 24 c 24 c 24
Current frequency Hz – – 50 60 50/60 – – –Energization threshold V 16.9 37.3 93 97 16 16.9 14.5 16.9Maximum operating voltage V 2. 57.6 140 140 264 2. 2. 2.Maximum drop-out voltage (Uo) V 3. .5 25.4 25.4 4 3. 2 3.Maximum current (at Us) mA 19.5 11 14 16 15 2 1 23Minimum holding current mA 2 2 2.5 2.5 2.5 2 1.3 2Maximum dissipated power (at Us) 50 Hz W – – 0.66 – 0.54 – – –
60 Hz W 0.45 0.52 – 0.73 0.77 0.64 0.43 0.55Disappearance of voltage maximum time up to which contact is maintained
ms 1 1 10 10 10 1 5 1
Display of control circuit by LED Yes Yes Yes Yes Yes Yes No YesBuilt-in protection reversed polarity Yes Yes – – – Yes Yes Yes
Contact characteristics (40°C ambient temperature)Type of interface ABR 2Epppp ABR 2S112B ABR 2S102B ABR 2pB312B (1)
Composition 1 N/O 1 N/O 1 N/O 1 C/OMaximum rated operating voltage (Ue max)
Conforming to IEC 947-5-1 a V 127 230 230 4c V 100 120 120 4
Maximum switching voltage a V 140 250 250 60c V 125 150 150 60
Operating current frequency Hz 50/60 50/60 50/60 50/60Thermal current Ith Conforming to IEC 947-1 A 1 5 5 0.05Rated operating current (Ie) for 1 million operating cycles
Conforming to IEC 947-5-1 Ue max
AC12 A 1 3 3 –AC14 A 0.5 1 1 –AC15 A 0.5 1 1 –
Conforming to IEC 947-5-1 Ue : c 24 V
DC12 A 1 1.7 1.7 –DC13 A 1 1.5 1.5 –
Minimum switching current mA 1 5 5 0.01Minimum switching voltage V 5 5 5 0.01Protection against short-circuits
For Ik ≤ 1 kA (a) and ≤ 100 A (c) Type and value of recommended fuse
Type : quick-blow fuse with high breaking capacityA 2 6.3 6.3 0.4
Low level contact reliability (17 V, 5 mA)/ABR-2pB (30 mV, 10 µA)
Number of faults per “n” million operating cycles
1 per 100 million
Other characteristicsMaximum operating time at Us (bounce included)
Between energization of coil and closing of N/O contact
c ms 10 10 10 6a ms 30 – – –
Between energization of coil and opening of N/C contact
ms – – – 6
Between de-energization of coil and opening of N/O contact
c ms 6 12 5 6a ms 30 – – –
Between de-energization of coil and closing of N/C contact
ms – – – 6
Maximum duration of bounce ms 5 5 5 2No make before break guaranteed between “N/C” and “N/O” contacts
Maximum make before break or break before make time
On energization ms – – – 5On de-energization ms – – – 2
Maximum operating rate
At no-load Hz 10 10 10 10At Ie Hz 0.5 0.5 0.5 –
Mechanical durability in millions of operating cycles
20 10 10 20
Rated insulation voltage
Conforming to IEC 947-1 V 300 300 300 300Conforming to VDE 0110 group C V 250 250 250 250
Insulation test voltage for 1 min
Coil circuit/contact circuits kV rms 2 4 4 1.5Wired interface/earth kV rms 2.5 2.5 2.5 2.5Between open contacts kV rms 0.75 1 1 1
(1) Do not switch inductive loads.(1) Do not switch inductive loads.
Presentation:page 5
Characteristics:page 59
Curves:page 61
References:page 62
Dimensions, schemes:page 63
Presentation:page 5
Characteristics:page 59
Curves:page 61
References:page 62
Dimensions, schemes:page 63
Characteristics (continued)
1
2
3
4
5
6
7
8
9
10
61
Interfaces For discrete signalsSlim electromechanical interface modules
Electrical durability of contacts (ABR 2S)Test conditions : in accordance with standard IEC 947-5-1 set up for rated control voltage.
a.c. loads
1 24 V2 4 V3 115 V4 230 V
AC12 : control of resistive loads and isolated solid state loads via optocouplercos j ≥ 0.9
AC14 : control of weak electro-magnetic loads of electro-magnets y 72 VAmake : cos j = 0.3break : cos j = 0.3AC15 : control of electro-magnetic loads of electro-magnets > 72 VAmake : cos j = 0.7break : cos j = 0.4
d.c. loads
1 24 V2 4 V3 115 V
DC12 : control of resistive loads and isolated solid state loads via optocoupler L/R ≤ 1 ms
DC13 : control of electro-magnets L/R ≤ 2 x (Ue x Ie) in ms.Ue : rated operating voltageIe : rated operating current(with a load protection diode)
5
4
3
2
1
1 2 3 4 5(A)
6
0
0
3
4
2
6
1
Operating cycles in millions
5
4
3
2
1
1 2 3 4 5(A)
6
0
0
3
4
2
6
1
Operating cycles in millions
2
1
0,5 1 1,5 2 2,5(A)
3
0
0
3
2
43
1
Operating cycles in millions
2
1
0,5 1 1,5 2 2,5(A)
3
0
0
3
2
43
1
Operating cycles in millions
2
1
0,5 1 1,5 2 2,5
(A)
3
0
0
3
1
23
Operating cycles in millions
2
1
0,5 1 1,5 2 2,5
(A)
3
0
0
3
1
23
Operating cycles in millions
2
1
0
0,5 1 1,5 2 2,5
(A)
23
3
30
1
Operating cycles in millions
2
1
0
0,5 1 1,5 2 2,5
(A)
23
3
30
1
Operating cycles in millions
Curves
1
2
3
4
5
6
7
8
9
10
62
Interfaces For discrete signalsSlim electromechanical interface modulesControl circuit : a.c. or d.c.
Input modules (9.5 mm pitch)Indication Composition Control circuit Sold in
lots ofUnit reference
Weight
V kgWith LED 1 N/C c 24 5 ABR 2E112B 0.032
c 4 5 ABR 2E112E 0.032
a 115...127 (50 Hz) 5 ABR 2E115F 0.035
a 120...127 (60 Hz) 5 ABR 2E116F 0.035
a 230...240 (50/60 Hz) 5 ABR 2E111M 0.036
Output modules (12 mm pitch)Indication Composition Control circuit Sold in
lots ofUnit reference
Weight
V kgWithout 1 N/C c 24 5 ABR 2S102B 0.040
With LED 1 N/C c 24 5 ABR 2S112B 0.041
Modules for very low level switching (17.5 mm pitch)Indication Composition Control circuit Reference Weight
V kgInput
With LED 1 C/O (1) c 24 ABR 2EB312B 0.04
OutputWith LED 1 C/O (1) c 24 ABR 2EB312B 0.04
Flexible comb accessoriesDescription For common Colour Distance
between cable ends
Reference Weight
cm kgFlexible comb modularity 8 x 1 mm2
Coil White 12 ABF C08R12W 0.020
2 ABF C08R02W 0.010
a Red 12 ABF C08R12R 0.020
2 ABF C08R02R 0.010
c Blue 12 ABF C08R12B 0.020
2 ABF C08R02B 0.010
(1) Do not switch inductive loads.
163
62
ABR 2E112B
163
62
ABR 2E112B
163
63
ABR 2S112B
163
63
ABR 2S112B
163
64
ABR 2EB112B
163
64
ABR 2EB112B
163
65
ABF C08Rppp
163
65
ABF C08Rppp
Presentation:page 5
Characteristics:page 59
Curves:page 61
References:page 62
Dimensions, schemes:page 63
Presentation:page 5
Characteristics:page 59
Curves:page 61
References:page 62
Dimensions, schemes:page 63
References
1
2
3
4
5
6
7
8
9
10
63
Interfaces For discrete signalsSlim electromechanical interface modules
DimensionsABR 2E11pp ABR 2S1p2B
ABR 2EB312B ABR 2SB312B
Circuit diagramsABR 2E112B (c 24 V) ABR 2E112E (c 4 V) ABR 2E11pF/M (a 115...240 V)
ABR 2S102B (c 24 V) ABR 2S112B (c 24 V) ABR 2pB312B (c 24 V)
78
75
70,59,5
7478
75
70,59,5
7478
75
70,512
74
78
75
70,512
74
78
75
70,5
63
17,5
74
78
75
70,5
63
17,5
74
78
75
70,5
63
17,5
74
78
75
70,5
63
17,5
74
+A
1
–A2
13 14
+A
1
–A2
13 14
+A
1
–A2
1413
+A
1
–A2
1413
A1
– A
213 14
A1
– A
213 14
1314
+A
1
–A2
1314
+A
1
–A2
1314
+A
1
–A2
1314
+A
1
–A2
141112
+A
1
–A2
141112
+A
1
–A2
Dimensions, schemes
1
2
3
4
5
6
7
8
9
10
64
Interfaces For discrete signalsSlim solid-state interface modules
The ABS-2 solid-state interface relays are supplied in the form of compact modules which appear identical to the ABR-2 electromechanical family.They are designed for interfacing discrete digital control signals exchanged within an automated system between the processor (PLC, numerical controller, etc) and the other components (contactors, solenoid valves, indicator lamps, proximity sensors, etc).They are suitable for use in equipment which requires the benefits of electronic technology : a high operating rate, virtually unlimited durability, silent operation, etc.These products are notable for their high performance and excellent adaptation to industrial environments, ensured by the fact that they conform to the most recent IEC standards.
CompositionThe ABS-2 range comprises 2 families :
Input interfaces The 9.5 mm wide input interfaces are designed for switching input signals to processors. They offer a wide choice of electrical isolation between signals due to the wide range of input voltages from c 5 V to a 230 V.
Output interfaces Output interfaces are designed for the control of preactuators (contactors, solenoid valves, etc) for the signalling devices (indicator lamps, audible warnings, etc). Two widths are available, 9.5 and 17.5 mm, depending on the switched current.
The 17.5 mm version comprises a 9.5 mm interface and an integrated mm spacer. This device can, with its increased ventilation, switch high levels of currents.
The front panel of the ABS-2 slim solid-state interface modules comprises:1 LED indicating the state of the control signal.2 Channel identification : 5 individual characters for AB1-/G or one AB1-SA2 marker
tag.3 Connection by screw clamp terminal enabling easy attachment of 2 wires per
terminal. The layout of the connection terminals for both families (input and output) is designed for rational wiring and a clear separation between the incoming (processing) and outgoing (power and process control) circuits.
4 Integrated spacer.
3
2
1
163
0
3
2
1
163
0
ABS2INTERSORT-PRO-3-B
3
2
1
163
7
ABS2INTERSORT-PRO-3-B
3
2
1
163
7
ABS-2
ABS2-PRO-3-B
3
2
1
4
163
79
ABS-2
ABS2-PRO-3-B
3
2
1
4
163
79
Presentation:page 64
Characteristics:page 65
Curves:page 6
References:page 6
Dimensions, schemes:page 69
Presentation:page 64
Characteristics:page 65
Curves:page 6
References:page 6
Dimensions, schemes:page 69
Presentation
1
2
3
4
5
6
7
8
9
10
65
Interfaces For discrete signalsSlim solid-state interface modules
Examples of applications with PLCsInterfacing PLC discrete inputs
Interfacing PLC discrete outputs
–
+
–
+
14
13
14
13
ABS - 2E
13
14
PNP 115/230 V
13
14
13
14A
1
A2
A1
A2
A1
A2
A1
A2
A1
A2
PLCPositive logic discrete inputs
PushbuttonsSeries contacts
2-wiresensors
3-wiresensors
PushbuttonsSeries contacts
2-wiresensors
Process power supply
Processing power supply
–
+
–
+
14
13
14
13
ABS - 2E
13
14
PNP 115/230 V
13
14
13
14A
1
A2
A1
A2
A1
A2
A1
A2
A1
A2
PLCPositive logic discrete inputs
PushbuttonsSeries contacts
2-wiresensors
3-wiresensors
PushbuttonsSeries contacts
2-wiresensors
Process power supply
Processing power supply
–
+
–
+
A1
A2
A1
A2
A1
A2
ABS - 2S
F
13 14 13 14 13 14
PLCPositive logic transistor (or relay) outputs
–
+
–
+
A1
A2
A1
A2
A1
A2
ABS - 2S
F
13 14 13 14 13 14
PLCPositive logic transistor (or relay) outputs
Environment
Conforming to standards IEC 947-5-1 Draft standard IEC 17 B secretariat 200
Product certifications UL, CSA, BV, LROS, DNVDegree of protection Conforming to IEC 529
(protection against direct contact)IP 20
Protective treatment “TC”Flame resistance Conforming to IEC 695-2-1 Incandescent wire °C 960
Conforming to UL 94 V0Shock resistance Conforming to IEC 6-2-27 Semi-sinusoidal waves 11 ms 30 gnVibration resistance Conforming to IEC 6-2-6 10…150 Hz 5 gnResistance to electrostatic discharges
Conforming to IEC 01-2 Level 3 kV
Resistance to electromagnetic fields
Conforming to IEC 01-3 Level 3 ; 27…1000 MHz V/m 10
Resistance to rapid transients
Conforming to IEC 01-4 Level 3
On power supply kV 2On I/O kV 1
Resistance to shock waves
Conforming to IEC 947-1 Waveform 1.2/50 ms ; 0.5 J
U < 50 V kV 0.5U < 150 V kV 1.5U < 300 V kV 2.5
Cross-sections which may be connected
Flexible cable with no cable end 1 or 2-wire mm2 0.6…2.5Flexible cable with cable end 1 or 2-wire mm2 0.34…2.5Rigid cable 1-wire mm2 0.27…4
Operating position AnyAmbient air temperature around the device
Unrestricted operation °C - 5…+ 55Operation at Us °C - 25…+ 70Storage °C - 40…+ 0
Operating altitude m ≤ 300Installation category Conforming to IEC 947-1 IIDegree of pollution Conforming to IEC 947-1 2Mounting Standard rails 5 1 4
Environment
Conforming to standards IEC 947-5-1 Draft standard IEC 17 B secretariat 200
Product certifications UL, CSA, BV, LROS, DNVDegree of protection Conforming to IEC 529
(protection against direct contact)IP 20
Protective treatment “TC”Flame resistance Conforming to IEC 695-2-1 Incandescent wire °C 960
Conforming to UL 94 V0Shock resistance Conforming to IEC 6-2-27 Semi-sinusoidal waves 11 ms 30 gnVibration resistance Conforming to IEC 6-2-6 10…150 Hz 5 gnResistance to electrostatic discharges
Conforming to IEC 01-2 Level 3 kV
Resistance to electromagnetic fields
Conforming to IEC 01-3 Level 3 ; 27…1000 MHz V/m 10
Resistance to rapid transients
Conforming to IEC 01-4 Level 3
On power supply kV 2On I/O kV 1
Resistance to shock waves
Conforming to IEC 947-1 Waveform 1.2/50 ms ; 0.5 J
U < 50 V kV 0.5U < 150 V kV 1.5U < 300 V kV 2.5
Cross-sections which may be connected
Flexible cable with no cable end 1 or 2-wire mm2 0.6…2.5Flexible cable with cable end 1 or 2-wire mm2 0.34…2.5Rigid cable 1-wire mm2 0.27…4
Operating position AnyAmbient air temperature around the device
Unrestricted operation °C - 5…+ 55Operation at Us °C - 25…+ 70Storage °C - 40…+ 0
Operating altitude m ≤ 300Installation category Conforming to IEC 947-1 IIDegree of pollution Conforming to IEC 947-1 2Mounting Standard rails 5 1 4
Characteristics
1
2
3
4
5
6
7
8
9
10
66
Interfaces For discrete signalsSlim solid-state interface modules
Control circuit characteristics (55°C ambient temperature)Type of interface ABS
2EC01EAABS 2EC01EB
ABS 2EC01EE
ABS 2EA01EF
ABS 2EA02EF
ABS 2EA01EM
ABS 2EA02EM
Rated voltage Us c V 5 24 4 – – – –a V – – – 115/127
50 Hz120/127 60 Hz
230/240 50 Hz
230/240 60 Hz
Maximum voltage c V Negative logic 6 (TTL)
2. 57.6 – – – –
a V – – – 140 140 264 264Maximum current at Us c mA 13.6 12 10.5 – – – –
a mA – – – 14 17 12.5 15State 1 assured c V 3.75 16.9 36 – – – –
mA 4.5 7.7 7.5 – – – –a V – – – 6.3 90 173 173
mA – – – .4 9.7 7.9 9.3State 0 assured c V 2 5.6 10. – – – –
mA 0.09 2 2 – – – –a V – – – 25.4 25.4 4 4
mA – – – 2.5 2.5 2.5 2.5State 1 display Yes Yes Yes Yes Yes Yes YesInternal protection reversed polarity Yes Yes Yes – – – –
Output circuit characteristicsRated operating voltage Ue c V 5...4Min/max voltage c V 2/60Min/max current switched mA 1/50Maximum residual current at state 0 mA 0.1Maximum volt drop at state 1 V 1Internal protection Reversed polarityExternal protection Against short-circuits for Ik ≤ 100 A (c)
Quick-blow fuse, ref. : HA21 0.25 A or equivalent
Other characteristicsType of interface ABS
2EC01EAABS 2EC01EB
ABS 2EC01EE
ABS 2EA01EF
ABS 2EA02EF
ABS 2EA01EM
ABS 2EA02EM
Time delay characteristics Response time max Ue ≤ 30 V Ie ≥ 5 mA
0 V 1 ms 0.05 0.05 0.05 10 10 10 101 V 0 ms 0.4 0.4 0.4 20 20 20 20
Maximum switching rate Duty cycle 50 % Ue ≤ 30 V Ie ≥ 5 mA
Hz 1000 1000 1000 25 25 25 25
Rated insulation voltage Conforming to IEC 947-1 : 300 VConforming to VDE 0110 : 250 V group C
Insulation test voltage for 1 minute
I/O kVrms 4Wired interface/earth kVrms 2.5
Presentation:page 64
Characteristics:page 65
Curves:page 6
References:page 6
Dimensions, schemes:page 69
Presentation:page 64
Characteristics:page 65
Curves:page 6
References:page 6
Dimensions, schemes:page 69
Characteristics (continued)
1
2
3
4
5
6
7
8
9
10
67
Interfaces For discrete signalsSlim solid-state interface modules
Control circuit characteristics (55°C ambient temperature)Type of interface ABS 2SC01EB ABS 2SC02EB ABS 2SA01MB ABS 2SA02MB
Rated voltage Us c V 24 24Maximum voltage V 2. 2.Maximum current at Us mA 12 13.6State 1 assured V 16.9 16.9
mA 7.7 .3State 0 assured V 5.6 5.3
mA 2 2State 1 display Yes YesInternal protection reversed polarity Yes Yes
Output circuit characteristicsRated operating voltage Ue V c 5...4 c 5...4 a 24...240 a 24...240Maximum voltage V c 57.6 c 57.6 a 264 a 264Maximum continuous current (Ith) (1) at 40 °C
A 2 3 2.3 3
Rated operating voltage (Ie) Conforming to IEC 947-5-1 Single/touching product at 55 °C vertical position
A DC12 1.5/0.9 2.5/2.2 AC12 1.9/0.5 2.1/1.5A DC13 1.5/0.9 2.5/2.2 AC13 1.6/0.5 1.6/1.5A DC14 0.6/0.6 0.6/0.6 AC14 1.6/0.5 1.6/1.5A – – – AC15 1/0.5 1/1
Minimum current c/a mA 1 10Maximum residual current c/a mA 1 2.5Maximum volt drop V 1.5 3 (Ie ≥ 10 mA)
1.5 (Ie ≥ 100 mA)“0 crossing” voltage V – 50 peakSolid-state dV/dt V/ms – 500Internal protection Reversed polarityExternal protection Against short-circuits for Ik ≤ 1 kA (a) and ≤ 100 A (c)
Quick-blow fuse with high breaking capacity: 3.15 A
Other characteristicsMaximum response time at Ie Š 10 mA
0 V 1 ms 0.05 10 (50 Hz) ; (60Hz)1 V 0 ms 0.6 10 (50 Hz) ; (60Hz)
Maximum switching rate At 55 °C ; at Ie: module alone duty cycle 40 %
Hz DC13 6 6 AC13 0.6 0.7Hz DC14 1 3 AC14 0.6 0.7Hz – – – AC15 0.6 0.7
On resistive load duty cycle 50 %
Hz 700 50
Rated operating voltage Conforming to IEC 947-1 : z 300 VConforming to VDE 0110 : 250 V group C
Rated Insulation voltage for 1 minute
I/O kVrms 4Wired interface/earth kVrms 2.5
(1) See temperature derating curves.(1) See temperature derating curves.
Characteristics (continued)
1
2
3
4
5
6
7
8
9
10
6
Interfaces For discrete signalsSlim solid-state interface modules
Solid-state input modulesWidth Input circuit Output circuit Sold in
lots ofUnit reference
WeightCurrent Nominal voltage Current Nominal voltage
mm V V kg9.5 c 5 c 5…4 5 ABS 2EC01EA 0.029
24 c 5…4 5 ABS 2EC01EB 0.0294 c 5…4 5 ABS 2EC01EE 0.029
a 115…127 (50 Hz) c 5…4 5 ABS 2EA01EF 0.032120…127 (60 Hz) c 5…4 5 ABS 2EA02EF 0.032230…240 (50 Hz) c 5…4 5 ABS 2EA01EM 0.033230…240 (60 Hz) c 5…4 5 ABS 2EA02EM 0.033
Solid-state output modulesWidth Input circuit Output circuit Sold in
lots ofUnit reference
WeightCurrent Nominal voltage Current Nominal voltage
mm V A V kg9.5 c 24 c 2 24…4 5 ABS 2SC01EB 0.034
a 2.3 24…230 5 ABS 2SA01MB 0.03417.5 c 24 c 3 24…4 1 ABS 2SC02EB 0.043
a 3 24…230 1 ABS 2SA02MB 0.044
AccessoriesFor connecting commons, use ABF C08ppp flexible combs (Please consult your customer care centre).
Temperature derating curve for solid-state output modules Uc = Us = c 24 VABS 2SC01EB d.c. ABS 2SC02EB d.c.
ABS 2SA01MB a.c. ABS 2SA02MB a.c.
1 Vertical module alone or adjacent to modules with low heat dissipation.
2 Horizontal module alone or adjacent to modules with low heat dissipation.
3 Vertical module mounted with 2 modules with identical heat dissipation on both sides.
4 Horizontal module mounted with 2 modules with identical heat dissipation on both sides.
10 20 30 40 50 60 70
1
2
3
1/2
00
3/4
Ie (A)
T °C ambient10 20 30 40 50 60 70
1
2
3
1/2
00
3/4
Ie (A)
T °C ambient10 20 30 40 50 60 70
1
2
3
1/2
00
4
3
Ie (A)
T °C ambient10 20 30 40 50 60 70
1
2
3
1/2
00
4
3
Ie (A)
T °C ambient
10 20 30 40 50 60 70
1
2
3
1/2
00
3/4
Ie (A)
T °C ambient10 20 30 40 50 60 70
1
2
3
1/2
00
3/4
Ie (A)
T °C ambient10 20 30 40 50 60 70
1
2
31/2
00
4
3
Ie (A)
T °C ambient10 20 30 40 50 60 70
1
2
31/2
00
4
3
Ie (A)
T °C ambient
Presentation:page 64
Characteristics:page 65
Curves:page 6
References:page 6
Dimensions, schemes:page 69
Presentation:page 64
Characteristics:page 65
Curves:page 6
References:page 6
Dimensions, schemes:page 69
References, curves
1
2
3
4
5
6
7
8
9
10
69
Interfaces For discrete signalsSlim solid-state interface modules
DimensionsABS 2E/ABS 2Sp01pp ABS 2Sp02pp
Circuit diagramsSolid-state input modulesABS 2ECpppp ABS 2EApppp ABS 2Epppp
Solid-state output modulesABS 2SC0pEB ABS 2SA0pMB ABS 2SC0pEB ABS 2SA0pMB
F: fuse DF1 SS133.2(1) or peak limiter
78
75
70,574
9,578
75
70,574
9,5 78
75
70,5
17,5
74
78
75
70,5
17,5
74
+A
1
–A2
+13 –14
+A
1
–A2
+13 –14
A
1
A
2
+13 –14
A
1
A
2
+13 –14
14
13
A2
A1
+ –
5…48 V
+ –14
13
A2
A1
+ –
5…48 V
+ –
+13
–14
+A1
–A2
+13
–14
+A1
–A2
1
3
1
4
+A
1
–A2
1
3
1
4
+A
1
–A2
1413
A2
A1
+ –
+ –
– F
5-24 V
Resistive load
1413
A2
A1
+ –
+ –
– F
5-24 V
Resistive load
1413
A2
A1
+ –
+ –
– F
5-24 V
(1)
Inductive load
1413
A2
A1
+ –
+ –
– F
5-24 V
(1)
Inductive load
1413
A2
A1
+ –
– F
5-24 V
Resistive load
1413
A2
A1
+ –
– F
5-24 V
Resistive load
1413
A2A1
+ –
– F
5-24 V
(1)
Inductive load
1413
A2A1
+ –
– F
5-24 V
(1)
Inductive load
Dimensions, schemes
1
2
3
4
5
6
7
8
9
10
2
1
3
4
5
6
7
8
9
10
7070
Selection guide Zelio Relay - Solid State Relays SSR solid state relays
Applications Panel mounted 5 rail mounted
PF5
2606
2-32
-Q
Contact type 1 N/O SPST contact 1 N/O SPST contact
Control voltage ranges a 90…20 V 90…20 V 90…140 Vc 3…32 V 4…32 V 3…32 V
Operating voltages a 24…20 V, 4…530 V, 4…660 V
24…20 V
Type of switching a
Zero voltage switching Zero voltage switching
Current a
10, 25, 50, 75, 90, 125 A 10, 20, 30 A 45 A
Degree of protection IP20 IP20
LED indication Yes Yes
Cooling Thermal protection or with heat sink accessory Built-in heat sink
Solid state relay typeSSR P SSR D
Page 76 76
PF5
2606
0-24
-Q
2
1
3
4
5
6
7
8
9
10
7171
Applications Panel mounted 5 rail mounted
PF5
2606
2-32
-Q
Contact type 1 N/O SPST contact 1 N/O SPST contact
Control voltage ranges a 90…20 V 90…20 V 90…140 Vc 3…32 V 4…32 V 3…32 V
Operating voltages a 24…20 V, 4…530 V, 4…660 V
24…20 V
Type of switching a
Zero voltage switching Zero voltage switching
Current a
10, 25, 50, 75, 90, 125 A 10, 20, 30 A 45 A
Degree of protection IP20 IP20
LED indication Yes Yes
Cooling Thermal protection or with heat sink accessory Built-in heat sink
Solid state relay typeSSR P SSR D
Page 76 76
PF5
2633
9-1
-Q
2
1
3
4
5
6
7
8
9
10
7272
Presentation Zelio Relay - Solid State RelaysSSR solid state relays
PresentationThe SSR solid state relay range comprises:
relays for panel mounting: SSR P.relays for 5 rail mounting: SSR D.
bb
DescriptionSSR P relays for panel mounting
2 x Ø 4.5 holes for fixing.Connection terminals.Connection terminal screws.Input indicator LED, green.Thermal interface which must be via the back of the product.
1 2 3 4 5
SSR D relays for 5 rail mountingLugs for panel mounting.Integrated heat sink.Connection terminals.Connection terminal screws.Input indicator LED, green.Bracket for mounting on 5 rail.
1 2 3 4 5 6
Presentation : page 72
Characteristics : page 73
References : page 76
Dimensions : page 77
1
2
4
1
5
3
1
2
56
1
43
2
1
3
4
5
6
7
8
9
10
7373
Characteristics Zelio Relay - Solid State RelaysSSR P solid state relays Panel mounting
General characteristicsProduct certifications UL E25297, CSA 1696Product marking e, IEC 60950Ambient air temperature around the device
Operation °C - 40…+ 0Storage °C - 40…+ 125
Encapsulation Thermally conductive epoxyDegree of protection IP20Terminal screw torque Nm
Inputs: 1.1 Outputs: 2.2
Relay type SCR output, Zero voltage switching SSR PCDS10A1 SSR PCDS25A1 SSR PCDS50A1Input specification
Control voltage range c V 3…32 3…32 3…32Minimum turn-on voltage c V 3 3 3Maximum turn-off voltage c V 1.0 1.0 1.0Typical input current mA 10 at c 12 V 10 at c 12 V 10 at c 12 V
Output specificationOperating voltage a V 24…20 24…20 24…20Load current range A 0.15 …10 0.15…25 0.15…50Transient overvoltage Vpk 600 600 600Maximum surge current (16.6 ms) Apk 120 250 625Maximum On-state voltage drop at rated current Vpk 1.6 1.6 1.6Thermal resistance junction to case °C/W 1.4 1.02 0.63Maximum I²t for fusing (8.3 ms) A²sec 60 260 1620Maximum off-state leakage current at rated voltage mA 1.0 1.0 1.0Minimum off-sate dv/dt at maximum rated voltage V/µsec 500 500 500Maximum turn-on time Cycle 1/2 1/2 1/2Maximum turn-off time Cycle 1/2 1/2 1/2
Relay type SCR output, Zero voltage switching SSR PCDS75A2 SSR PCDS90A3 SSR PCDS125A3Input specification
Control voltage range c V 4…32 4…32 4…32Minimum turn-on voltage c V 4 4 4Maximum turn-off voltage c V 1.0 1.0 1.0Typical input current mA 15 at c 5 V 15 at c 5 V 15 at c 5 V
Output specificationOperating voltage a V 4…530 4…660 4…660Load current range A 0.15…75 0.15…90 0.15…125Transient overvoltage Vpk 1200 1200 1200Maximum surge current (16.6 ms) Apk 1000 1200 1750Maximum On-state voltage drop at rated current Vpk 1.6 1.6 1.7Thermal resistance junction to case °C/W 0.31 0.2 0.22Maximum I²t for fusing (8.3 ms) A²sec 4150 6000 12 700Maximum off-state leakage current at rated voltage mA 10 1.0 1.0Minimum off-sate dv/dt at maximum rated voltage V/µsec 500 500 500Maximum turn-on time Cycle 1/2 1/2 1/2Maximum turn-off time Cycle 1/2 1/2 1/2
2
1
3
4
5
6
7
8
9
10
7474
Characteristics (continued) Zelio Relay - Solid State RelaysSSR P solid state relaysPanel mounting
Relay type SCR output, Zero voltage switching SSR PP8S10A1 SSR PP8S25A1 SSR PP8S50A1Input specification
Operating voltage a V 90…20 90…20 90…20Minimum turn-on voltage Vrms 90 90 90Maximum turn-off voltage Vrms 10 10 10Typical input current mA 2 at 120 Vrms 2 at 120 Vrms 2 at 120 Vrms
Output specificationOperating voltage a V 24…20 24…20 24…20Load current range A 0.04…10 0.04…25 0.04…50Transient overvoltage Vpk 600 600 600Maximum surge current (16.6 ms) Apk 120 250 625Maximum On-state voltage drop at rated current Vpk 1.6 1.6 1.6Thermal resistance junction to case °C/W 1.4 1.02 0.63Maximum I²t for fusing (8.3 ms) A²sec 60 260 1620Maximum off-state leakage current at rated voltage mA …10 …10 …10Minimum off-sate dv/dt at maximum rated voltage V/µsec 500 500 500Maximum turn-on time Cycle 1/2 1/2 1/2Maximum turn-off time Cycle 1/2 1/2 1/2
Relay type SCR output, Zero voltage switching SSR PP8S75A2 SSR PP8S90A3 SSR PP8S125A3Input specification
Operating voltage a V 90…20 90…20 90…20Minimum turn-on voltage Vrms 90 90 90Maximum turn-off voltage Vrms 10 10 10Typical input current mA 2 at 120 Vrms 2 at 120 Vrms 2 at 120 Vrms
Output specificationOperating voltage a V 0…530 4…660 4…660Load current range A 0.04…75 0.04…90 0.15…125Transient overvoltage Vpk 1200 1200 1200Maximum surge current (16.6 ms) Apk 1000 1200 1750Maximum On-state voltage drop at rated current Vpk 1.7 1.7 1.7Thermal resistance junction to case °C/W 0.31 0.2 0.22Maximum I²t for fusing (8.3 ms) A²sec 4150 6000 12 700Maximum off-state leakage current at rated voltage mA 10 5 5Minimum off-sate dv/dt at maximum rated voltage V/µsec 500 500 500Maximum turn-on time Cycle 1/2 1/2 1/2Maximum turn-off time Cycle 1/2 1/2 1/2
Presentation : page 72
Characteristics : page 73
References : page 76
Dimensions : page 77
2
1
3
4
5
6
7
8
9
10
7575
Characteristics Zelio Relay - Solid State RelaysSSR D solid state relay5 rail mounting
General characteristicsProduct certifications UL E25297, CSA 1696Product marking e, IEC 60950Ambient air temperature around the device
Operation °C - 40…+ 0Storage °C - 40…+ 125
Encapsulation Thermally conductive epoxyDegree of protection IP20Terminal screw torque 10…30 A relays Nm Inputs: 0.6…0.7
Outputs: 0.6…0.745 A relays Nm
Inputs: 0.6…0.7 Outputs: 1.1…1.7
Relay type SCR output, Zero voltage switching SSR DP8S10A1 SSR DP8S20A1 SSR DP8S30A1 SSR DF8S45A1Input specification
Operating voltage a V 90…20 90…20 90…20 90…140Minimum turn-on voltage Vrms 90 90 90 90Maximum turn-off voltage Vrms 10 10 10 10Typical input current mA
2 (120 Vrms), 4 (240 Vrms)
2 (120 Vrms), 4 (240 Vrms)
2 (120 Vrms), 4 (240 Vrms)
15 (120 Vrms)
Output specificationOperating voltage a V 24…20 24…20 24…20 24…20Load current range A 0.15…10 0.15…20 0.15…30 0.15…45Transient overvoltage Vpk 600 600 600 600Maximum surge current (16.6 ms) Apk 120 250 625 625Maximum On-state voltage drop at rated current Vpk 1.6 1.6 1.6 1.6Maximum I²t for fusing (8.3 ms) A²sec 60 260 1620 1620Maximum off-state leakage current at rated voltage mA 10 10 10 10Minimum off-sate dv/dt at maximum rated voltage V/µsec 500 500 500 500Maximum turn-on time Cycle 1/2 1/2 1/2 1/2Maximum turn-off time Cycle 1/2 1/2 1/2 1/2
Relay type SCR output, Zero voltage switching SSR DCDS10A1 SSR DCDS20A1 SSR DCDS30A1 SSR DCDS45A1Input specification
Control voltage range c V 4…32 4…32 4…32 3…32Minimum turn-on voltage c V 4.0 4.0 4.0 4.0Maximum turn-off voltage c V 1.0 1.0 1.0 1.0Typical input current mA …12 …12 …12 17
Output specificationOperating voltage a V 24…20 24…20 24…20 24…20Load current range A 0.15…10 0.15…20 0.15…30 0.15…45Transient overvoltage Vpk 600 600 600 600Maximum surge current (16.6 ms) Apk 120 250 625 625Maximum On-state voltage drop at rated current Vpk 1.6 1.6 1.6 1.6Maximum I²t for fusing (8.3 ms) A²sec 60 260 1620 1620Maximum off-state leakage current at rated voltage mA 10 10 10 10Minimum off-sate dv/dt at maximum rated voltage V/µsec 500 500 500 500Maximum turn-on time Cycle 1/2 1/2 1/2 1/2Maximum turn-off time Cycle 1/2 1/2 1/2 1/2
2
1
3
4
5
6
7
8
9
10
7676
References Zelio Relay - Solid State RelaysSSR solid state relays
Solid state relays, 1 N/O SPST contactPanel mountingb
Switching Voltage range Load current range
References WeightInput Output
V V A kgSCR output
Zero voltage switching
c 3…32 a 24…20 10 SSR PCDS10A1 0.113
25 SSR PCDS25A1 0.113
50 SSR PCDS50A1 0.113
c 4…32 a 4…530 75 SSR PCDS75A2 0.113
a 4…660 90 SSR PCDS90A3 0.113
125 SSR PCDS125A3 0.113
a 90…20 a 24…20 10 SSR PP8S10A1 0.113
25 SSR PP8S25A1 0.113
50 SSR PP8S10A1 0.113
a 0…530 75 SSR PP8S75A2 0.113
a 4…660 90 SSR PP8S90A3 0.113
125 SSR PP8S125A3 0.113
5 rail mounting bSCR output
Zero voltage switching
a 90…20 a 24…20 10 SSR DP8S10A1 0.272
20 SSR DP8S20A1 0.272
30 SSR DP8S30A1 0.272
a 90…140 a 24…20 45 SSR DF8S45A1 0.42
c 4…32 a 24…20 10 SSR DCDS10A1 0.272
20 SSR DCDS20A1 0.272
30 SSR DCDS30A1 0.272
c 3…32 a 24…20 45 SSR DCDS45A1 0.42
Accessories for panel mounted relaysDescription For use with relays Unit references Weight
kgHeat sink SSR PPSpppp,
SSR PCDSppppSSR AH1 0.47
Thermal interfaceSold in lots of 10
SSR PPSpppp, SSR PCDSpppp
SSR AT1 0.011
SSR AT1
PF5
2606
4-2
-Q
SSR PCDS25A1
PF5
2606
0-24
-Q
SSR DCDS10A1
PF5
2633
9-1
-Q
SSR DCDS45A1
PF5
2606
2-32
-Q
SSR AH1
PF5
2606
3-50
-Q
Presentation : page 72
Characteristics : page 73
References : page 76
Dimensions : page 77
2
1
3
4
5
6
7
8
9
10
7777
Dimensions Zelio Relay - Solid State RelaysSSR solid state relays
Solid state relays, 1 N/O SPST contactPanel mountingb
Solid state relays SSR P Thermal interface SSR AT1
35,547,1
45,5
= =
58,4
47,3
Ø4,5
47,7
4,6
55,1
42,4
Heat sink SSR AH1
115,8
66
120,6139,7114,3
4,6 4,6
5 rail mounting b10…30 A relays 45 A relays
22,5
98,8 80 89,7
11,2(1)
97,7
Ø4,4 Ø4,4
22,6
106,7
45,513,15
(1)
98,8
76,2
87,4
(1) Ø 4.4 x 5.5 elongated hole (1) Ø 4.4 x 5.5 elongated hole
ART. 960361 DIA
3ED
2090
304E
N
Schneider Electric Industries SAS www.schneider-electric.com
Head office35, rue Joseph Monier92500 Rueil-MalmaisonFrance
The information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein. This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications. It is the duty of any such user or integrator to perform the appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant specific application or use thereof. Neither Schneider Electric nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information contained herein.
Design: blueloft.frPhotos: Schneider ElectricPrinted by: Schneider Electric
top related