contents easy set up · 2018. 1. 10. · 1.change default password 3. if you forgot the password,...

633GB(Q3)快速安装指南-英文版

折后尺寸：107*175mm

材质：128g铜版纸

双面四色印刷，过哑胶

注：机器图为首页

HD IP Camera Q3(720P)/Q3S(1080P)

1 Installation Guide, 1 CD1 Camera(include Antenna), 1 Power Adapter1 User Manual,Mounting Accessories

, 1 Network Cable

Contents

Power for the camera with the included power supply and placeit near your router.

Power on cameraStep 2

Easy Set Up

The instruction is for reference only. Slight differences may be found in the

user interface.All the designs and software here are subject to change

without prior written notice.For latest instructions, please go to www.wansview.com to download.

Step 1 Download

·Wansview

Go to the App Store or Google Play to search and download “ ” APP to your supported device .

www.wansview.com

LET US KNOWWHAT YOU THINK

Thank you so much for your order and trust to Wansview.Please feel free to contact us if you have any questions about the product application.

As a young and growing company, it would mean the world to us if you could leave an honest review about our product and services.

US:service@wansview.com UK:service3@wansview.com

US:service2@wansview.comUK:service3@wansview.com

Facebook: www.facebook.com/WansviewClub/

Youtube: https://www.youtube.com/channel/ UCPRXQcIkLsMAWQtpGxVx_jw

OFF: The device is not powered

LAMBENT: The device is powering

SLOW: No network connection

STEADY: Connect WiFi successfully

QUICK: Start to upgrade/Reset successfully

OFF: The device is powered 5 minutes but not connect Wi-Fi yet

SLOW: Not connect WiFi

QUICK: The device is connecting WiFi now

STEADY: The device has connected WiFi already

Red (Status LED)

Blue (WiFi LED)

One Smarteye One WorldiOSAndroid

Always remember to change your password, tap the“ ”and then access to Edit Camera Page, get into“Advanced Setting” then“User Setting”, change password and click to save.

>

·Or scan the QR code below to get the app.

wansview App icon

2.If the night vision stops working, please turn on the IR light as below:

FAQ:1.Change Default Password

3. If you forgot the password, hold the “Reset” button around 15-20 seconds, then the camera will be back to factory default.Default User/password: admin/123456. Remember to configure WiFi again after the Reset.

Microphone

·Launch the Wansview app, Click to access Add Camera page and select“Add cameras via WiFi mode”.

Step 3 Connect to network

1

·Check the camera’s blue light, if it is flashing slowly, please tap “Blue light is flashing slowly”, and Scan the QR code on the bottom of the camera, and name the camera. Then “Next” (keep "admin" as login name and "123456" as the default password ).

3QR Code

Q3

·Your WiFi name will be located there (If the WiFi is not what you want to connect. please tap to switch the needed WiFi), input the correct WiFi Password (Wi-Fi name and Password should not contain special characters ' and & .)and click “Connect to WiFi”.And move your phone close to the camera and turn up the phone volume, then “Next” and “Start”.

5

76

8

·The phone will send a sequence of beeps to the camera and try to connect WiFi, If wifi set up succeed, the app will go back to Camera page and show “ Succeed”and the camera will be “online”.

WiFi Configuration

Q3S

Attention: When the camera shows “online”, you can move the camera to other place where has a good WiFi signal.

If failed to connect to WiFi, Please try to connect the camera with ethernet cable and use “Add camera via wired method” to set up the camera.

1

2

3

4

Tap this icon to turn night vision on

Tap this icon to turn night vision off

Antenna

IR light

Photoresistant

Lens

Speaker

RJ45

Reset Mirco-SD SlotPower Port

Reset

QR Code

DDNSCamera ID(DID)

Factory DefaultAccout Info

1080P

2