corso di stampa 3d - parte 1
Post on 13-Jun-2015
1.994 Views
Preview:
DESCRIPTION
TRANSCRIPT
Parte 1/2
3D Printing e Prototipazione Rapida Low Cost
Creare Oggetti
Tecnica Sottrattiva
Tecnica Additiva
Stampanti Open Hardware
Rapid Replicating Prototiper
Open Hardware <> Free Hardware
FDM
fused deposition modeling
190 - 230°C
Cosa posso creare?
Tecnologie
FDM
Fused Deposition Modeling
SLS
Selective Laser Sintering
LOM
Laminated Object Manifacturing
Area di 150 x 170 metri per un'altezza di 26 metri - Siviglia. Jurgen Mayer H.
DLP
Digital Light Processing
«A Getto»
Storia delle stampanti
Quando è stata inventata la prima
stampante 3D?
1984
Chuck Hull
1985, ZCorp
Oggi non esiste più: è stata acquisita nel 2012 dalla 3D System
La brevetta
Una ZCorp a Milano
Il laboratorio OneOf
Il brevetto scade nel 2005...
nessuno lo rinnova!
2004, Università di Bath
Adrian Bowyer
Pubblica un post sulla possibilità di costruire una macchina autoreplicante
Deve costare poco
RepRap
RepRap
2007, NYCResistor
NYCResistor è un hackerspace...
Bre Pettis + Zach Smith
Sono due maker! nel 2009 si aggiunge Adrian Mayer
Deve essere ancora più semplice da montare
Vendono stampanti in kit
2009, SXSW
South by Southwest è un festival musicale e cinematografico che si tiene ogni anno ad Austin, Texas.
Sono una MakerBot. Creo oggetti. Cosa posso fare per te? Portami a casa
Primo post del blog di MakerBot
3500 kit in un mese
403.000.000$
Nel 2013 Stratasys acquista MakerBot
Intanto, in Italia...
Siamo nel 2011
KentStrapper
In Brianza...
ShareBot
ShareBot NG
Wasp
FabTotum
Nel 2013 chiedono 50.000 euro su IndieGoGo e ne ricevono 560.000
Una stampa in 5 minuti
Stampa di un oggetto in ABS, scaricato da Thingiverse
Affetto il file (slicing)
Make!
Toolchain di stampa
IdeaDisegnoSTLGCodeStampante
IdeaDisegnoSTLGCodeStampante
IdeaDisegnoSTLGCodeStampante
IdeaDisegnoSTLGCodeStampante
IdeaDisegnoSTLGCodeStampante
I bravi artisti copiano, i grandi artisti rubano
Picasso
Non conta da dove prendete le cose,
ma dove le portate
Godard
Export in STL
Formato StereoLitografico ... mesh di triangoli
Watertight
Normale alla superficie
Slicing
Il disegno fatto a fette e la produzione di G-Code - CAM
Slic3r
Creato da Alessandro Ranellucci, Architetto di Roma
Skeinforge
Progetto Open Source legato a MakerBot
PrintRun
Repetier Host
ReplicatorG
Slicing
Raft
The reason to print a supportive raft or base underneath your 3D model is obvious: the base absorbs any imperfections of your build plate; and if curling has to happen, it only afects the base, will not infect your model, so that your model bottom could retain flat.
Raft
Over Hang
Shells
GCode
Printing...
Letture
http://www.lulu.com/spotlight/zeppelinmaker
Grazie!Paolo Aliverti@zeppelinmakerwww.zeppelinmaker.it
top related