curso básico construccion de un motor bedini
Post on 10-Oct-2015
104 Views
Preview:
TRANSCRIPT
-
Curso Bsico de Construccin de un motor BediniNoviembre 2013
Por Arturo Cano Jaraba
-
A QU LLAMAMOS MOTOR BEDINI
Introduccin
-
John Bedini 1984
-
SSG Esquema de John Bedini
-
SSG motor (Simplified School Girl motor)
-
SG motor (school girl motor)
-
ES OVERUNITY ESTE MOTOR?
Motor BEDINI
-
es overunity este motor?
No, nunca vas a obtener del motor ms energa de la que pongas. Da igual cmo lo midas.
-
TUV test
John Bedini dice que puedes cargar cuatro bateras al precio de una!
-
TUV testBATTERY TEST FOR THE BEDINI MOTOR GENERATOR
DATE : OCTOBER 13, 2000 BATTERY TEST SEQUENCE:One lead acid gel-cell (12 volts, 450 milliamps) is being utilized as the primary source fully charged at 12.5 volts. Three (3) lead acid gel-cell batteries (12 volt, 450 milliamps) strapped in parallel are being used as the charge destination. The batteries are discharged to 10 volts for the test purposes. Test #1 starts at 10:45 AM utilizing primary battery fully charged at 12.5 volts charging three (3) destination batteries paralleled. The destination batteries reach a charge capacity of 14 volts at 11:20 AM. The destination batteries are then discharged to 10 volts under working load to prepare for Test #2. Test #2 starts at 11:25 AM utilizing primary battery measured at 11.5 volts. Charging three (3) destination batteries paralleled. The destination batteries reach a charge capacity of 14 volts at 12:50 PM. The destination batteries are then discharged to 10 volts under working load to prepare for Test #3. Test #3 starts at 1:00 PM utilizing primary battery measured at 10.5 volts. Charging three (3) destination batteries paralleled. The destination batteries reach a charge capacity of 14 volts at 1:40 PM. The destination batteries are then discharged to 10 volts under working load to prepare for Test #4. Test #4 starts at 2:05 PM utilizing primary battery measured at 9.5 volts. Charging three (3) destination batteries paralleled. The destination batteries reach a charge capacity of 13 volts at 2:40 PM. The primary battery is now discharged to 9 volts under working load and unable to further run the Bedini motor generator. TOTAL BATTERIES CHARGED: 12 lead acid gel-cell batteries (12 volts, 450 milliamps each). This ratio is a 12 to 1 charging factor. The motor operation (work) being performed as this was done is not included as an additional factor in this test.
-
es overunity este motor?
Pero no dices que no es OVERUNITY?
-
Qu ms hace un motor Bedini?
Se mueve, hace un trabajo y puedes aprovecharlo, por ejemplo te puedes hacer un ventilador .
Carga bateras sin calentarlas Carga bateras ms rpido que un cargador
convencional Recupera bateras sulfatadas Genera energa radiante
-
MATERIAL NECESARIO
MOTOR BEDINI
-
Material necesario
Rueda de bicicleta o un rotor. NO MAGNTICA. Usa tu imaginacin
-
Material necesario
Un carrete de plstico u otro material no magntico.Plastico, 75mm largo, 18mm
dametro del agujero central
-
Material necesario
Varillas de soldadura.Lincoln R60.
Acero recubiertas de cobre 1,6 mm.
-
Material necesario
Imanes Cermicos Aconsejables (25mm x 50mm x 18mm).OJO! NO DE NEODIMIO
-
Material necesario
Soporte para el rotorAconsejable de madera o plstico- NO MAGNTICO!
-
Material necesario
Hilo de Cobre45 metros
0,4mm y 0,56 mm
-
Material necesario
Bateras de plomoAconsejables de ciclo profundo. Para este motor como mnimo de 7 Amp. No fuerces la batera por encima del C20
-
Transistor
2N3055, 100V, TO-3 MJL21194
Hilo de conexin
2 Diodos
1N4001, 1A, 50V (1N914)
1N4007, 1A, 1000V ( 1N5408)
Lmpara de Nen Resistencia
100 ohms, w
Potencimetro
1K ohms, 2 w
-
Herramientas que puedes necesitar
Tijeras o pela cables Ampermetro de 5 amp (como muy poco de
1 amp) Polmetro Alicates para cortar las varillas Soldador y estao Destornilladores Cuenta km de bici o un tacmetro Brjula Cinta aislante Pegamento Loctite o Glue 3 Cinta americana
-
Y DESPUS DE CONSTRUIDO QU
MOTOR BEDINI
-
Pruebas
Calculadora de COP
-
HAGAMOS UN MOTOR
MOTOR BEDINI
-
La seguridad es lo primero
Los imanes si salen disparados son peligrosos. Usa cinta americana o equivalente alrededor de la rueda para sujetar los imanes. Esta seguridad es adicional a pegar los imanes a la rueda.
Las bateras de plomo contienen cido sulfrico que es altamente corrosivo y es venenoso. Cuando se trabaja con bateras debes usar gafas de seguridad y ropa de proteccin adecuada, el espacio de trabajo debe estar ventilado y debes quitarte todo tipo de joyas, relojes, etc.
Lava tus manos despus de estar en contacto con las bateras. Para neutralizar cido derramado usa bicarbonato de sosa.
-
SSG motor (Simplified School Girl motor)
-
SG motor (Pulser)
top related