eternus dx60 s2 - fiola - login customer · configure lun mapping with affinity (1) following...

0 Copyright Fujitsu Technology Solutions, Release September 2011

ETERNUS DX60 S2

Management Utility GUI and CLI

Management Utility GUI and CLI ETERNUS DX60 S2

ETERNUS Management

Web GUI CLI

Management Utility GUI and CLI ETERNUS DX60 S2 Copyright Fujitsu Technology Solutions, Release September 2011 1

Management Utility Overview: GUI

Outline Logon Built-in User Accounts ETERNUS Login Screen Menu Structure Sub Menu Overview

Management Utility GUI and CLI ETERNUS DX60 S2 Copyright Fujitsu Technology Solutions, Release September 2011 2

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2

Outline (1) A Management Utility, or Web GUI, is used to set the operating

environment and to check the status of the ETERNUS DX60 S2 The Web GUI is operated via a web browser

Fibre Channel (FC) / iSCSI / SAS

Ethernet ETERNUS DX60 S2

3

Outline (2) Basic requirements for the server or PC required for the use of

the GUI Browser

• Internet Explorer 6.0, 7.0 or 8.0 • Mozilla Firefox 3.0.x, 3.5.x and 3.6.x

Screen resolution • 1024 x 768 or higher

LAN connection

Two connection topologies are allowed Direct cable connection

• Either a normal or crossover LAN cable can be used Network connection via an existing LAN

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2 4

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2

Outline (3) Initial and basic settings by the wizards The wizards enable you to set the basic features of the ETERNUS DX60 S2 by

following the given instructions

System status General status of the system

Advanced system configuration For example: Defining Hot Spares, RAID migration, setting up Eco-mode

etc.

Checking the extent of a failure If a disk drive failure occurs, this function provides additional diagnostics

information helping to understand how widespread the consequences are • For example, which Volumes, LUNs and Host ports are being affected

Easy operation If a hardware failure is detected, the system administrator can receive an email

containing the detected fault information

5

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2

Logon Start the browser and connect to the default IP address of the

ETERNUS (192.168.1.1)

6

Built-in User Accounts (1) The available menus of the GUI depend on the account type

used to log in The table on the following page shows the user roles and the

respectively available functions

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2 7

Built-in User Accounts (2)

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2

User Role Description Available Functions Account

Advanced Account with maintenance engineer privileges such as status display, configuration management and maintenance functions

• Initial Setup • Status • Volume Settings • Global Settings • Maintenance • Log/Dump • Utilities

f.ce

Standard Account with System Administrator privileges such as status display and configuration management

• Initial Setup • Status • Volume Settings • Global Settings • Maintenance (Add Drive

Enclosures), Log/Dump

root

Monitor Account with general user privileges, only status display function is available

• Status • Log/Dump (Display Event

Log and Display Performance Information)

User settable

8

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2

ETERNUS Login Screen After Logon the first screen you see is the Storage System

Status

9

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2

Menu Structure Global Header

Menu Bar

Sub Menu Bar

10

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2

Sub Menu Overview Status

Easy Setup

Volume Settings

Global Settings

Maintenance

Log/Dump

Utilities

11

ETERNUS Management

Configuration Wizard RAID Group Management Volume Management Host Interface Management Configuring LUN Mapping

Management Utility GUI and CLI ETERNUS DX60 S2 Copyright Fujitsu Technology Solutions, Release September 2011 12

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2

Configuration Wizard (1) Create RAID Group Bind a group of disks to a RAID Group

Create Volume Define storage capacity within a RAID Group as a Volume which is seen

by the server as a LUN

Define Host Register the server information to be connected to the ETERNUS DX60

S2 via an FC port

Configure Affinity Group Creates a group of LUNs and Servers

Define LUN Mapping Specify the Volume to be recognized by the server

• With or without Host affinity • LUN visible for selected Host or Hosts • LUN visible for all Hosts

13

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2

Configuration Wizard (2) The Wizard is started from the Menu Bar "Easy Setup" Select "Configuration Wizard" from the Sub Menu Bar Press Start

14

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2

Configuration Wizard (3) The Configuration Wizard guides you from creation of a RAID

Group…

…to the definition of the LUN Mapping

15

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2

RAID Group Management (1) Overview of the RAID Group Management functions Create/Delete RAID Group Assign/Release Hot Spare Logical Device Expansion Set RAID Group name Set ECO Mode Schedule Modify RAID Group Parameters

16

RAID Group Management (2) Number of disks that can be set for each RAID level

Maximal total number of RAID Groups is 12

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2

RAID Level

Number of Disks Recommended Number of Disks DX60 S2

RAID 1 2 2 (1D+1M) RAID 1+0 4 - 24 4 (2D+2M), 6 (3D+3M), 8 (4D+4M), 10 (5D+5M) RAID 5 3 - 16 3 (2D+1P), 4 (3D+1P), 5 (4D+1P), 6 (5D+1P) RAID 6 5 - 16 5 (3D+2P), 6 (4D+2P), 7(5D+2P) RAID 5+0 (3-12) x2 3 (2D+1P) x2, 4 (3D+1P) x 2,

5 (4D+1P) x2, 6 (5D+1P) x2

17

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2

Volume Management (1) The Create Volume function creates Volumes in existing RAID

Groups Open Data Volume or Snap Data Volume (SDV) can be created with this

function

After completing the Volume creation, the new Volumes are formatted automatically Maximal number of Volumes that can be set per RAID Group 1024 in total, 128 per RAID Group

Volumes can be accessed by the Host after LUN mapping has been done

18

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2

Volume Management (2) Overview of the Volume Management functions Create/Delete Volume Format Volume Encrypt Volume LUN Concatenation RAID Migration Initialize Snap Data Volume Modify Cache Parameters Release Reservation Set Volume Name

19

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2

Volume Management (3) Create Volume(s) in a selected RAID Group

20

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2

Host Interface Management Overview of the Host Interface Management functions Set FC Port Parameters Setup FC Host Configure LUN Mapping Setup Host Response Modify Reset Group

21

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2

Configure LUN Mapping The Configure LUN Mapping function sets the relationship

between a Logical Unit Number (LUN) and a Volume number LUN mapping enables the server access to the Volumes in the

ETERNUS DX60 S2 The maximal number of WWNs and Affinity Groups varies

depending on the overall system configuration Prerequisites for the Host Affinity function Host Affinity must be enabled at least on one Host port At least one server must be connected to a port for which Host Affinity is

enabled

Up to 512 LUNs can be mapped

22

Configure LUN Mapping with Affinity (1) Following parameters can be set here LUN Mapping Affinity Group Port connected to the server Specific information (WWN for HBA) for the server to access the Affinity

Group

An "Affinity Group" defines which server(s) can access which LUNs Multiple Affinity Groups

can be created

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2 23

Configure LUN Mapping with Affinity (2) Connecting an Affinity Group with a Host (server)

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2 24

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2

Configure LUN Mapping without Affinity This section describes the following settings LUN Mapping Port connected to the server

This function specifies the Host LUN allocation to the Volume for each port

25

Command Line Interface (CLI)

Command Format

Management Utility GUI and CLI ETERNUS DX60 S2 Copyright Fujitsu Technology Solutions, Release September 2011 26

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2

ETERNUS CLI In addition to the graphical Web GUI, the ETERNUS DX60 S2

has also a character based Command Line Interface (CLI) With CLI it is possible to carry out configuration settings and

maintenance tasks using commands and command scripts The CLI can be used over the Ethernet port Telnet, an SSH application, or a terminal emulator on the

management server or PC is used to connect to the CLI

27

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2

CLI Command Format The command format command-name parameter parameter ... parameter command-name: Verb section + Object section

• Example: create volume parameter: hyphenated parameter section + Operand section

• Example: -n 80

Create raid-group Show raid-groups

28

Additional Reading Reference documentation for the ETERNUS Web GUI ETERNUS Web GUI, User's Guide, ETERNUS DX60 S2

• P2X0-1120-01ENZ0 • Link to document

ETERNUS documentation in Fujitsu PRIMEWEB Link to Fujitsu PRIMEWEB

Please note that accessing the above links require a Fujitsu Partner user account

Copyright Fujitsu Technology Solutions, Release September 2011 Management Utility GUI and CLI ETERNUS DX60 S2 29