gsw 6ax - gaspari menotti
Post on 10-Mar-2016
227 Views
Preview:
DESCRIPTION
TRANSCRIPT
GASPARIMENOTTI
GSWMACCHINA SAGOMATRICE A FILO DIAMANTATO
PROFILING MACHINE BY DIAMOND WIRE
LA PROGRAMMAZIONE DELLE FORME DA REALIZZARE PUÒ ESSERE FATTA DIRETTAMENTE SUL PC A BORDO MACCHINA OPPURE DA UN PC DALL'UFFICIO, CON LA POSSIBILITÀ DI SIMULARE LA LAVORAZIONE, E QUINDI TRASFERIRLA SULLA MACCHINA.
THE PROGRAM OF THE SHAPES TO BE DONE CAN BE DIRECTLY DONE ON PC, ON MACHINE’S BOARD OR BY A PC FROM THE OFFICE, WITH THE POSSIBILITY TO SIMULATE THE PROCESSING AND THEN, TRANSFERRED ON THE MACHINE.
Durante la fase di lavoro è visibile graficamente la forma del pezzo ed il suo stato di avanzamento. In caso di interruzione del ciclo di lavoro, causato da qualunque motivo, la macchina è in grado di ripartire dal punto in cui è stata interrotta senza la necessità di fare un reset degli assi perché ogni asse è dotato di trasduttore di posizione di tipo "assoluto".
Il software in dotazione, residente sulla macchina o in un Pc esterno, permette la programmazione della modalità con cui deve essere eseguito il pezzo: si possono impostare sia il percorso di taglio che le eventuali pause per il recupero cavallo, le fermate per assicurare il pezzo, i percorsi a ritroso per uscire dal pezzo in maniera automatica e poi riprendere l'esecuzione da un altro punto.Ogni pezzo, può essere realizzato in svariati modi e quindi l'operatore è libero di eseguire il profilo, in base alla sua esperienza e alle sue esigenze, in modo semplice ed intuitivo.
GLI ASSI_THE AXES
During the working phase, the shape of the piece and its progress can be graphically seen. In case of interruption of working cycle, caused by any reason, the machine is able to start again from the point in which it has been interrupted, without the necessity to do a reset of axes as, each axis, is equipped with a position transducer “absolute” type.
The software, on the machine or on an external PC, allows to program of the way by which the piece has to be done: both the cutting and eventual pauses to extend the wire again, the stops to secure the piece, the backward ways to go out, from the piece, in automatic and then, start the execution again, from another point etc. Each piece, of any material, can be done in many ways and then the operator is free to do the profile, according to his experience and his needs, in a simple and intuitive way.
L'UNICO LIMITE... LA TUA FANTASIA
ONLY ONE LIMIT...YOUR IMAGINATION
L'UNICO LIMITE... LA TUA FANTASIA
ONLY ONE LIMIT...YOUR IMAGINATION
LA PROGRAMMAZIONE DELLE FORME DA REALIZZARE PUÒ ESSERE FATTA DIRETTAMENTE SUL PC A BORDO MACCHINA OPPURE DA UN PC DALL'UFFICIO, CON LA POSSIBILITÀ DI SIMULARE LA LAVORAZIONE, E QUINDI TRASFERIRLA SULLA MACCHINA.
THE PROGRAM OF THE SHAPES TO BE DONE CAN BE DIRECTLY DONE ON PC, ON MACHINE’S BOARD OR BY A PC FROM THE OFFICE, WITH THE POSSIBILITY TO SIMULATE THE PROCESSING AND THEN, TRANSFERRED ON THE MACHINE.
Durante la fase di lavoro è visibile graficamente la forma del pezzo ed il suo stato di avanzamento. In caso di interruzione del ciclo di lavoro, causato da qualunque motivo, la macchina è in grado di ripartire dal punto in cui è stata interrotta senza la necessità di fare un reset degli assi perché ogni asse è dotato di trasduttore di posizione di tipo "assoluto".
Il software in dotazione, residente sulla macchina o in un Pc esterno, permette la programmazione della modalità con cui deve essere eseguito il pezzo: si possono impostare sia il percorso di taglio che le eventuali pause per il recupero cavallo, le fermate per assicurare il pezzo, i percorsi a ritroso per uscire dal pezzo in maniera automatica e poi riprendere l'esecuzione da un altro punto.Ogni pezzo, può essere realizzato in svariati modi e quindi l'operatore è libero di eseguire il profilo, in base alla sua esperienza e alle sue esigenze, in modo semplice ed intuitivo.
GLI ASSI_THE AXES
During the working phase, the shape of the piece and its progress can be graphically seen. In case of interruption of working cycle, caused by any reason, the machine is able to start again from the point in which it has been interrupted, without the necessity to do a reset of axes as, each axis, is equipped with a position transducer “absolute” type.
The software, on the machine or on an external PC, allows to program of the way by which the piece has to be done: both the cutting and eventual pauses to extend the wire again, the stops to secure the piece, the backward ways to go out, from the piece, in automatic and then, start the execution again, from another point etc. Each piece, of any material, can be done in many ways and then the operator is free to do the profile, according to his experience and his needs, in a simple and intuitive way.
L'UNICO LIMITE... LA TUA FANTASIA
ONLY ONE LIMIT...YOUR IMAGINATION
L'UNICO LIMITE... LA TUA FANTASIA
ONLY ONE LIMIT...YOUR IMAGINATION
GSW DAI FORMA ALLE TUE IDEESHAPE YOUR IDEAS
LA MACCHINA SAGOMATRICE A FILO DIAMANTATO MODELLO GSW/6AX, GRAZIE ALL'UTILIZZO DI UN SISTEMA A 6 ASSI INDIPENDENTI È IN GRADO DI ESEGUIRE LAVORAZIONI COMPLESSE NELLO SPAZIO DI FORMA CILINDRICA, CONICA O FORME COMBINATE PER ARTE FUNERARIA, EDILIZIA URBANA, SCULTURA, SU OGNI TIPO DI MATERIALE LAPIDEO.
THE PROFILING MACHINE BY DIAMOND WIRE MODEL GSW/6AX, THANKS TO A SYSTEM WITH 6 INDEPENDENT AXES, IS ABLE TO PERFORM 2D AND 3D SHAPES SUCH AS COLUMNS, CONES, TOMBSTONES, COMPLEX SHAPES FOR TOMBSTONES OR URBAN BUILDING IN ALL TYPES OF NATURAL STONES.
La struttura della macchina è realizzata in carpenteria metallica in acciaio elettro-saldato, progettata per garantirne la massima rigidità e precisione durante tutte le fasi di lavoro.
I due volani, uno motore e l'altro tensionatore sono realizzati in una speciale lega di alluminio, hanno un diametro di 1500 mm per preservare la durata del filo diamantato.
The body of the machine is made in electro-welded structure and has been designed to grant the max rigidity and precision during all working phases.
The two large flywheels, one driving and one idle devoted to the tensioning of the diamond wire are made in special aluminium-alloy having a diameter of 1500mm. to grant the maximum life of the diamond wire.
STRUTTURA MACCHINA
Il tensionamento del filo diamantato si ottiene facendo scorrere il volano tenditore su ruote prismatiche e guide rettificate tramite un cilindro pneumatico regolato idraulicamente.
Durante il taglio la tensione del filo viene controllata tramite le posizioni del cilindro tensionatore, rilevata da un trasduttore lineare.
The tensioning of the diamond wire is ensured by a pneumatic cylinder, hydraulically adjusted, that control the displacements of the idle-flywheel, moving in a system of prismatic wheels on rectified guides.
During the cut, the tensioning of the diamond wire is controlled and kept constant by a linear transducer that control the position of the tensioning-piston.
SISTEMA DI TENSIONAMENTOSTRUCTURE OF THE MACHINE TENSIONING
La programmazione delle forme da realizzare può essere fatta direttamente sul pc a bordo macchina oppure da un Pc dall'ufficio, con la possibilità di simulare la lavorazione, e quindi trasferirla sulla macchina.
L'interfaccia TOUCH SCREEN dedicata è semplice ed intuitiva, quindi estremamente facile da utilizzare da parte dell'operatore.
The programming of the shapes can be done directly on the machine PC installed on the control-board or in your PC with the possibility to simulate the required profile; once realised the obtained shape can be easily transferred to the machine.
The dedicated interface is simple, intuitive and extremely easy to be utilised by the operator.
INTERFACCIAINTERFACE
GSW 6AXGSW 6AX
GSW DAI FORMA ALLE TUE IDEESHAPE YOUR IDEAS
LA MACCHINA SAGOMATRICE A FILO DIAMANTATO MODELLO GSW/6AX, GRAZIE ALL'UTILIZZO DI UN SISTEMA A 6 ASSI INDIPENDENTI È IN GRADO DI ESEGUIRE LAVORAZIONI COMPLESSE NELLO SPAZIO DI FORMA CILINDRICA, CONICA O FORME COMBINATE PER ARTE FUNERARIA, EDILIZIA URBANA, SCULTURA, SU OGNI TIPO DI MATERIALE LAPIDEO.
THE PROFILING MACHINE BY DIAMOND WIRE MODEL GSW/6AX, THANKS TO A SYSTEM WITH 6 INDEPENDENT AXES, IS ABLE TO PERFORM 2D AND 3D SHAPES SUCH AS COLUMNS, CONES, TOMBSTONES, COMPLEX SHAPES FOR TOMBSTONES OR URBAN BUILDING IN ALL TYPES OF NATURAL STONES.
La struttura della macchina è realizzata in carpenteria metallica in acciaio elettro-saldato, progettata per garantirne la massima rigidità e precisione durante tutte le fasi di lavoro.
I due volani, uno motore e l'altro tensionatore sono realizzati in una speciale lega di alluminio, hanno un diametro di 1500 mm per preservare la durata del filo diamantato.
The body of the machine is made in electro-welded structure and has been designed to grant the max rigidity and precision during all working phases.
The two large flywheels, one driving and one idle devoted to the tensioning of the diamond wire are made in special aluminium-alloy having a diameter of 1500mm. to grant the maximum life of the diamond wire.
STRUTTURA MACCHINA
Il tensionamento del filo diamantato si ottiene facendo scorrere il volano tenditore su ruote prismatiche e guide rettificate tramite un cilindro pneumatico regolato idraulicamente.
Durante il taglio la tensione del filo viene controllata tramite le posizioni del cilindro tensionatore, rilevata da un trasduttore lineare.
The tensioning of the diamond wire is ensured by a pneumatic cylinder, hydraulically adjusted, that control the displacements of the idle-flywheel, moving in a system of prismatic wheels on rectified guides.
During the cut, the tensioning of the diamond wire is controlled and kept constant by a linear transducer that control the position of the tensioning-piston.
SISTEMA DI TENSIONAMENTOSTRUCTURE OF THE MACHINE TENSIONING
La programmazione delle forme da realizzare può essere fatta direttamente sul pc a bordo macchina oppure da un Pc dall'ufficio, con la possibilità di simulare la lavorazione, e quindi trasferirla sulla macchina.
L'interfaccia TOUCH SCREEN dedicata è semplice ed intuitiva, quindi estremamente facile da utilizzare da parte dell'operatore.
The programming of the shapes can be done directly on the machine PC installed on the control-board or in your PC with the possibility to simulate the required profile; once realised the obtained shape can be easily transferred to the machine.
The dedicated interface is simple, intuitive and extremely easy to be utilised by the operator.
INTERFACCIAINTERFACE
GSW 6AXGSW 6AX
GSW 6AX
Dati Tecnici | Technical data
Le descrizioni, i disegni ed i pesi non sono impegnativi. L’azienda costruttrice si riserva il diritto di apportare variazioni, anche sostanziali, senza darne preavviso, non permettendo perciò a terzi diritto di
contestazione o rivalse di sorta. Le macchine vengono fornite prive di lubrificanti.
Descriptions, drawings and weights are not binding. The supplier can make any change, even substantial, without notice. Nobody can raise any objections or claims. The machines are supplied without lubricants.
7.5
2500
max 1500
girevole 360°
20
+/-2000
20°
18
Main electric motor
Useful cutting length
Useful cutting height
Block carrying trolley (A axis)
Block carrying trolley loading capacity
Useful block carrying trolley stroke
Max working inclination
Total power
Motore elettrico principale
Lunghezza utile di taglio
Altezza utile di taglio
Carrello portablocchi (asse A)
Portata carrello portablocchi
Corsa utile carrello portablocchi
Inclinazione massima di lavoro
Potenza totale installata
kW
mm
mm
Ton
mm
kW
GSW/6AX
930
500
585
105
630
LA PROGRAMMAZIONE DELLE FORME DA REALIZZARE PUÒ ESSERE FATTA DIRETTAMENTE SUL PC A BORDO MACCHINA OPPURE DA UN PC DALL'UFFICIO, CON LA POSSIBILITÀ DI SIMULARE LA LAVORAZIONE, E QUINDI TRASFERIRLA SULLA MACCHINA.
THE PROGRAM OF THE SHAPES TO BE DONE CAN BE DIRECTLY DONE ON PC, ON MACHINE’S BOARD OR BY A PC FROM THE OFFICE, WITH THE POSSIBILITY TO SIMULATE THE PROCESSING AND THEN, TRANSFERRED ON THE MACHINE.
Durante la fase di lavoro è visibile graficamente la forma del pezzo ed il suo stato di avanzamento. In caso di interruzione del ciclo di lavoro, causato da qualunque motivo, la macchina è in grado di ripartire dal punto in cui è stata interrotta senza la necessità di fare un reset degli assi perché ogni asse è dotato di trasduttore di posizione di tipo "assoluto".
Il software in dotazione, residente sulla macchina o in un Pc esterno, permette la programmazione della modalità con cui deve essere eseguito il pezzo: si possono impostare sia il percorso di taglio che le eventuali pause per il recupero cavallo, le fermate per assicurare il pezzo, i percorsi a ritroso per uscire dal pezzo in maniera automatica e poi riprendere l'esecuzione da un altro punto.Ogni pezzo, può essere realizzato in svariati modi e quindi l'operatore è libero di eseguire il profilo, in base alla sua esperienza e alle sue esigenze, in modo semplice ed intuitivo.
GLI ASSI_THE AXES
During the working phase, the shape of the piece and its progress can be graphically seen. In case of interruption of working cycle, caused by any reason, the machine is able to start again from the point in which it has been interrupted, without the necessity to do a reset of axes as, each axis, is equipped with a position transducer “absolute” type.
The software, on the machine or on an external PC, allows to program of the way by which the piece has to be done: both the cutting and eventual pauses to extend the wire again, the stops to secure the piece, the backward ways to go out, from the piece, in automatic and then, start the execution again, from another point etc. Each piece, of any material, can be done in many ways and then the operator is free to do the profile, according to his experience and his needs, in a simple and intuitive way.
GSW 6AX
GSW 6AX
Dati Tecnici | Technical data
Le descrizioni, i disegni ed i pesi non sono impegnativi. L’azienda costruttrice si riserva il diritto di apportare variazioni, anche sostanziali, senza darne preavviso, non permettendo perciò a terzi diritto di
contestazione o rivalse di sorta. Le macchine vengono fornite prive di lubrificanti.
Descriptions, drawings and weights are not binding. The supplier can make any change, even substantial, without notice. Nobody can raise any objections or claims. The machines are supplied without lubricants.
7.5
2500
max 1500
girevole 360°
20
+/-2000
20°
18
Main electric motor
Useful cutting length
Useful cutting height
Block carrying trolley (A axis)
Block carrying trolley loading capacity
Useful block carrying trolley stroke
Max working inclination
Total power
Motore elettrico principale
Lunghezza utile di taglio
Altezza utile di taglio
Carrello portablocchi (asse A)
Portata carrello portablocchi
Corsa utile carrello portablocchi
Inclinazione massima di lavoro
Potenza totale installata
kW
mm
mm
Ton
mm
kW
GSW/6AX
930
500
585
105
630
LA PROGRAMMAZIONE DELLE FORME DA REALIZZARE PUÒ ESSERE FATTA DIRETTAMENTE SUL PC A BORDO MACCHINA OPPURE DA UN PC DALL'UFFICIO, CON LA POSSIBILITÀ DI SIMULARE LA LAVORAZIONE, E QUINDI TRASFERIRLA SULLA MACCHINA.
THE PROGRAM OF THE SHAPES TO BE DONE CAN BE DIRECTLY DONE ON PC, ON MACHINE’S BOARD OR BY A PC FROM THE OFFICE, WITH THE POSSIBILITY TO SIMULATE THE PROCESSING AND THEN, TRANSFERRED ON THE MACHINE.
Durante la fase di lavoro è visibile graficamente la forma del pezzo ed il suo stato di avanzamento. In caso di interruzione del ciclo di lavoro, causato da qualunque motivo, la macchina è in grado di ripartire dal punto in cui è stata interrotta senza la necessità di fare un reset degli assi perché ogni asse è dotato di trasduttore di posizione di tipo "assoluto".
Il software in dotazione, residente sulla macchina o in un Pc esterno, permette la programmazione della modalità con cui deve essere eseguito il pezzo: si possono impostare sia il percorso di taglio che le eventuali pause per il recupero cavallo, le fermate per assicurare il pezzo, i percorsi a ritroso per uscire dal pezzo in maniera automatica e poi riprendere l'esecuzione da un altro punto.Ogni pezzo, può essere realizzato in svariati modi e quindi l'operatore è libero di eseguire il profilo, in base alla sua esperienza e alle sue esigenze, in modo semplice ed intuitivo.
GLI ASSI_THE AXES
During the working phase, the shape of the piece and its progress can be graphically seen. In case of interruption of working cycle, caused by any reason, the machine is able to start again from the point in which it has been interrupted, without the necessity to do a reset of axes as, each axis, is equipped with a position transducer “absolute” type.
The software, on the machine or on an external PC, allows to program of the way by which the piece has to be done: both the cutting and eventual pauses to extend the wire again, the stops to secure the piece, the backward ways to go out, from the piece, in automatic and then, start the execution again, from another point etc. Each piece, of any material, can be done in many ways and then the operator is free to do the profile, according to his experience and his needs, in a simple and intuitive way.
GSW 6AX
GASPARIMENOTTI
Gaspari Menotti S.p.A.Viale Zaccagna, 18/F 54033 - CARRARA (MS) - ITALIATel.: +39 0585 64551 Fax.: +39 0585 645555 gaspari@gasparimenotti.com
www.gasparimenotti.com
Discover the Gaspari World
The Gaspari Solution
MADE IN ITALY
I N N OVAT I O N + T E C H N O LO GY + D E S I G N + C U S T O M E R CA R E + I N N OVAT I O N + T E C H N O LO GY + D E S I G N + C U S T O M E R CA R E
top related