network+ guide to networks, fourth edition
Post on 10-Jan-2016
13 Views
Preview:
DESCRIPTION
TRANSCRIPT
NETWORK+ GUIDE TO NETWORKS, FOURTH EDITION
Chapter 5Networking Hardware
2
OBJECTIVES
Identify the functions of LAN connectivity hardware
Install and configure a NIC (Network Interface Card)
Identify problems associated with connectivity hardware
2
4
OBJECTIVES (CONTINUED)
Describe the factors involved in choosing a NIC, hub, switch, or router
Discuss the functions of repeaters, hubs, bridges, switches, routers, and gateways, and the OSI Model layers at which they operate
Describe the use and types of routing protocols
4
6
NICS (NETWORK INTERFACE CARDS)
Connectivity devices that enable workstations, servers, printers, or other nodes to receive and transmit data over network media Usually contain data transceiver Belong to Physical and Data Link layers Apply data signals to wire Assemble and disassemble data frames Interpret physical addressing information Determine which node has right to transmit data at
any given instant
6
7
Kết nối thiết bị cho phép máy trạm, máy chủ, máy in, hoặc các nút khác để nhận và truyền dữ liệu qua phương tiện truyền thông mạngThường chứa các dữ liệu thu phátPhụ thuộc về các lớp liên kết vật lý và dữ liệuÁp dụng các tín hiệu dữ liệu kết nối dâyLắp ráp và tháo rời các khung dữ liệuGiải thích vật lý thông tin địa chỉXác định nút có quyền truyền dữ liệu bất cứ lúc nào ngay lập tức
8
TYPES OF NICS
NICs come in variety of types depending on: Access method Network transmission speed Connector interfaces Type of compatible motherboard or device Manufacturer
8
9
NIC có nhiều loại tùy thuộc vào:Phương pháp truy cậpTốc độ mạng truyền dẫnGiao diện kết nối Sự tương thích bo mạch chủ với thiết bị Nhà sản xuất
10
INTERNAL BUS STANDARDS
Bus: circuit used by motherboard to transmit data to computer’s components Including memory, processor, hard disk, and NIC Capacity defined principally by:
Width of data path (number of bits that can be transmitted in parallel)
Clock speed
Expansion slots allow devices to connect to computer’s expanded bus Devices found on circuit board called an expansion
card
10
11
INTERNAL BUS STANDARDS
Bus: mạch được sử dụng bởi bo mạch chủ để truyền dữ liệu để các thành phần của máy tínhBao gồm bộ xử lý, bộ nhớ, đĩa cứng, và NICCông suất được xác định chủ yếu bởi:Độ rộng của đường dẫn dữ liệu (số bit có thể được truyền song song)Tốc độKhe cắm mở rộng cho phép các thiết bị để kết nối với đường truyền mở rộng của máy tínhThiết bị trên bảng mạch gắn trên khe cắm nêu trên được gọi là một card mở rộng
11
12
INTERNAL BUS STANDARDS (CONTINUED)
Peripheral Component Interconnect (PCI): 32- or 64-bit bus with 33- or 66-MHz clock speed Maximum data transfer rate is 264 MBps
Industry Standard Architecture (ISA): original PC bus type
PCI Express specifies 64-bit bus with 133-MHz clock speed Capable of up to 500 MBps per data path Efficient data transfer, support for quality of service
distinctions, error reporting and handling, and compatibility with current PCI software
12
13
INTERNAL BUS STANDARDS (CONTINUED)
Peripheral Component Interconnect (PCI): truyền 32 bits - hoặc 64-bits với tốc độ 33 - hay 66 MHzTốc độ truyền dữ liệu tối đa là 264 MBpsIndustry Standard Architecture (ISA): loại card máy tính ban đầuPCI Express truyền dữ liệu 64-bit với tốc độ 133-MHzCó khả năng lên đến 500 MBps cho mỗi đường dẫn dữ liệuTruyền dữ liệu hiệu quả, hỗ trợ cho chất lượng truyền riêng biệt nhiều dịch vụ, báo cáo lỗi và xử lý, và khả năng tương thích với phần mềm PCI hiện tại
13
14
INTERNAL BUS STANDARDS (CONTINUED)
14
Figure 5-3: A motherboard with multiple expansion slots
15
PERIPHERAL BUS STANDARDS
Personal Computer Memory Card International Association (PCMCIA) adapter: connect external devices to most laptop computers PC Card: First PCMCIA adapter
Specified 16-bit interface running at 8 MHz CardBus: 32-bit interface running at 33 MHz ExpressCard: 26-pin interface, offering data transfer
rates of 250 MBps in each direction
15
16
Card chức năng (PCMCIA) là thiết bị ngoại vi của hầu hết các máy laptop PC Card: trước nhất Card PCMCIA
Chạy trên giao diên 16 bits với tốc độ 8 MHz CardBus: Chạy trên gao diện 32-bit với tốc độ 33 MHz ExpressCard: card có 26-pin (chân ) truyền dữ liệu và
khả năng truyền đến 250 MBps trên mỗi hướng truyền
17
PERIPHERAL BUS STANDARDS (CONTINUED)
17
Figure 5-4: A CardBus NIC
18
PERIPHERAL BUS STANDARDS (CONTINUED)
USB: standard interface used to connect multiple types of peripherals USB 1.1, USB 2.0 and USB 3.0
FireWire: codified by IEEE as IEEE 1394 Can be used to connect many types of peripherals Can connect computers on a small network 4-pin and 6-pin connectors
CompactFlash: most likely found connecting devices too small to handle PCMCIA slots
18
19
PERIPHERAL BUS STANDARDS (CONTINUED)
USB: tiêu chuẩn giao diện được sử dụng để kết nối nhiều loại thiết bị ngoại viUSB 1.1, USB 2.0 và USB 3.0FireWire: hệ thống hóa bởi IEEE là IEEE 1394Có thể được sử dụng để kết nối nhiều loại thiết bị ngoại viCó thể kết nối máy tính trên một mạng nhỏLoại 4-chân kết nối và loại 6-chânCompactFlash: có khả năng kết nối các thiết bị quá nhỏ để xử lý các khe cắm PCMCIA
19
20
PERIPHERAL BUS STANDARDS (CONTINUED)
20
Figure 5-6: A USB NIC
21
ON-BOARD NICS
Some peripheral devices connect directly to motherboard using on-board ports e.g., a mouse
Many new computers use on-board NICs Integrated into motherboard
21
22
ON-BOARD NICS
Một số thiết bị ngoại vi kết nối trực tiếp với bo mạch chủ bằng cách sử dụng cổng mạchVí dụ: chuộtNhiều máy tính mới sử dụng NIC on-boardTích hợp vào bo mạch chủ
22
23
WIRELESS NICS
23
Figure 5-9: Wireless NICs
24
INSTALLING NICS
First install hardware, then software May have to configure firmware
Set of data or instructions saved to a ROM [electrically erasable programmable read-only memory (EEPROM)]
Always read manufacturer’s documentation and follow proper safety procedures
Multiple NICs may be installed Jumper: plastic piece with metal receptacle Dual inline package (DIP) switch indicates
parameter setting
24
25
INSTALLING NICS
Đầu tiên cài đặt phần cứng, sau đó phần mềmCó thể cấu hình từ hảng sản xuất Bộ dữ liệu hoặc lênh thực thi lưu vào ROM [lập trình bộ nhớ chỉ đọc (EEPROM)]Luôn luôn đọc tài liệu của nhà sản xuất và thực hiện theo quy trình an toàn thích hợpNIC đa năng có thể được cài đặtJumper: mảnh nhựa đựng kim loại (đóng mở mạch)Gói nội tuyến kép (DIP) chuyển đổi cho thấy cài đặt thông số
25
26
INSTALLING AND CONFIGURING NIC HARDWARE
26
Figure 5-10: A properly inserted NIC
27
INSTALLING AND CONFIGURING NIC HARDWARE (CONTINUED)
27
Figure 5-11: Installing a PCMCIA-standard NIC
28
INSTALLING AND CONFIGURING NIC SOFTWARE
Device driver: software enabling attached device to communicate with computer’s OS Must ensure that correct device driver installed and
configured properly for the NIC To install from Windows XP interface, need
Windows XP software and NIC’s device drivers Can usually download NIC software from
manufacturer’s Web site Installing NIC drivers on UNIX or Linux depends
somewhat on OS version
28
29
INSTALLING AND CONFIGURING NIC SOFTWARE
Điều khiển thiết bị: phần mềm cho phép thiết bị này để giao tiếp với hệ điều hành máy tínhPhải đảm bảo đúng trình điều khiển thiết bị được cài đặt và cấu hình đúng cho NICĐể cài đặt từ giao diện Windows XP, cần có phần mềm Windows XP và trình điều khiển thiết bị của NICThường có thể tải về phần mềm NIC từ trang Web của nhà sản xuấtCài đặt trình điều khiển NIC trên UNIX hay Linux phụ thuộc phần nào vào phiên bản hệ điều hành
29
30
INSTALLING AND CONFIGURING NIC SOFTWARE (CONTINUED)
30
Figure 5-13: Fedora Core Linux Network Configuration window
31
INTERPRETING LED INDICATORS
NICs may have one or more of following lights:ACT: if blinking, indicates that NIC is either
transmitting or receiving dataLNK: if lit, NIC is functionalTX: if blinking, NIC is functional and
transmitting framesRX: if blinking, NIC is functional and receiving
frames
31
32
INTERPRETING LED INDICATORS
NIC có thể có một hoặc nhiều đèn sau đây:ACT: nếu nhấp nháy, chỉ ra rằng các NIC hoặc truyền tải hoặc nhận dữ liệuLNK: nếu ánh sáng, NIC chức năng hoạt độngTX: nếu nhấp nháy, NIC chức năng truyền khungRX: nếu nhấp nháy, NIC chức năng nhận khung
32
33
IRQ (INTERRUPT REQUEST)
Message to computer instructing it to stop what it is doing and pay attention to something else
Interrupt: circuit board wire over which device issues voltage to signal IRQ
IRQ number: means by which bus understands which device to acknowledge Range from 0 to 15
33
34
IRQ (INTERRUPT REQUEST)
Thông điệp tới máy tính các cấu trúc lịnh để ngăn chặn những gì nó đang làm và lưu ý vấn đề nào đó khácCác ngắt: bảng mạch dây cho kết nối thiết bị với điện áp theo tín hiệu IRQIRQ :là phương thức thiết bị nhận biết đường truyềnCó phạm vi từ 0 đến 15
34
35
IRQ (CONTINUED)
Symptoms possibly indicating two devices attempting to use same IRQ: Computer locks up either upon starting or when OS is
loading Computer runs much more slowly than usual Devices such as USB or parallel ports stop working Video or sound card problems Computer fails to connect to network Intermittent data errors during transmission
35
36
IRQ (CONTINUED)
Các triệu chứng có thể chỉ ra hai thiết bị cố gắng sử dụng cùng một IRQ:Máy tính bị treo khi khởi động hoặc khi hệ điều hành đang tảiMáy tính chạy chậm hơn nhiều hơn bình thườngCác thiết bị như USB hoặc cổng song song ngừng làm việcCó vấn đề về Video hoặc card âm thanhMáy tính không kết nối vào mạngDữ liệu liên tục sai sót trong quá trình truyền
36
37
IRQ (CONTINUED)
If IRQ conflicts occur, must reassign device’s IRQ Through OS Through adapter’s EEPROM configuration utility or
computer’s CMOS configuration utility Complementary metal oxide semiconductor
(CMOS): microchip that stores settings pertaining to computer’s devices
Basic input/output system (BIOS): instructions enabling computer to initially recognize hardware
37
38
IRQ (CONTINUED)
Nếu IRQ xung đột xảy ra, phải gán lại các cổng IRQ của thiết bịThông qua hệ điều hànhThông qua tiện ích cấu hình EEPROM hoặc bộ chuyển đổi tiện ích cấu hình CMOS của máy tínhGán lại (CMOS): vi mạch và lưu các cài đặt liên quan đến thiết bị máy tínhThiết bị nhập xuất hệ thống (BIOS): gán lịnh cho phép máy tính tự động nhận ra phần cứng
38
39
MEMORY RANGE
Indicates area of memory that NIC and CPU use for exchanging (buffering) data Hexadecimal notation
Some memory ranges reserved for specific devices
NICs typically use memory range in high memory area A0000–FFFFF Some manufacturers prefer certain ranges
39
40
MEMORY RANGE
Xác định vùng bộ nhớ mà NIC và CPU sử dụng để trao đổi dữ liệu (buffering)ký hiệu theo hexadecimalMột số vùng bộ nhớ dành riêng cho các thiết bị cụ thểNIC thường sử dụng bộ nhớ phạm vi trong khu vực bộ nhớ caoA0000-FFFFFMột số nhà sản xuất tham chiếu phạm vi nhất định
40
41
BASE I/O PORT
Specifies area of memory that will act as channel for moving data between NIC and CPU Hexadecimal notation Device’s base I/O port cannot be used by any other
device Most NICs use two memory ranges for this
channel Base I/O port settings identify beginning of each
range
41
42
BASE I/O PORT
Xác định khu vực của bộ nhớ sẽ hoạt động như là một kênh để di chuyển dữ liệu giữa NIC và CPUKý hiệu theohexadecimal Thiết bị của cổng xuất nhập cơ sở I / O không thể được sử dụng bởi bất kỳ thiết bị khácHầu hết các NIC sử dụng hai dãy bộ nhớ cho kênh nàyCổng cơ sở I / O thiết lập nhận diện bắt đầu của mỗi phạm vi
42
43
FIRMWARE SETTINGS
Modify NIC’s transmission characteristics When changing firmware settings, actually
writing to NIC’s EEPROM chip Need bootable disk containing configuration or install
utility shipped with NIC NIC configuration utilities:
View IRQ, I/O port, base memory, node address Perform diagnostics
To perform entire group of diagnostic tests on utility disk, must have loopback plug
43
44
FIRMWARE SETTINGS
Hiệu chỉnh các đặc tính truyền dẫn của NICKhi thay đổi các thiết lập firmware, thực sự là ghi lại lệnh cho chip EEPROM NICCần đĩa khởi động có khả năng chứa cấu hình hay cài đặt tiện ích gán vào NICTiện ích cấu hình NIC:Xem IRQ, I / O port, bộ nhớ cơ sở, các nút địa chỉ Thực hiện chẩn đoánĐể thực hiện toàn bộ nhóm các xét nghiệm chẩn đoán trên đĩa tiện ích phải có thiết bị hồi báo
44
45
REPEATERS AND HUBS
Repeaters: simplest type of connectivity devices that regenerate a digital signal Operate in Physical layer
Cannot improve or correct bad or erroneous signal Regenerate signal over entire segment One input port and one output port Suited only to bus topology networks
45
46
REPEATERS AND HUBS
Bộ lặp: đơn giản là thiết bị kết nối phục hồi các tín hiệu kỹ thuật sốHoạt động trong lớp vật lýKhông thể cải thiện hoặc sửa chữa tín hiệu xấu hoặc có sai sótTái tạo tín hiệu trên toàn bộ phân khúcMột cổng đầu vào và đầu ra một cổngPhù hợp nhất với cấu trúc truyền trong hình thái mạng
46
47
REPEATERS AND HUBS (CONTINUED)
Hub: repeater with more than one output port Multiple data ports Operate at Physical layer Uplink port: allows connection to another hub or
other connectivity device On Ethernet networks, can serve as central
connection point of star or star-based hybrid topology On Token Ring networks, hubs are called Multistation
Access Units (MAUs)
47
48
REPEATERS AND HUBS (CONTINUED)
Hub: bộ lặp có nhiều cổng đầu raNhiều cổng dữ liệuHoạt động ở lớp vật lýCổng đa kết: cho phép kết nối đến một trung tâm hoặc thiết bị kết nối khácTrên các mạng Ethernet, có thể phục vụ như là điểm kết nối trung tâm của ngôi sao ngôi sao dựa trên cấu trúc liên kết laiTrên các mạng Token Ring, trung tâm được gọi là đơn vị truy cập đa trạm Multistation (Maus)
48
49
REPEATERS AND HUBS (CONTINUED)
Hubs (continued): Connected devices share same amount of bandwidth
and same collision domain Logically or physically distinct Ethernet network segment on
which all participating devices must detect and accommodate data collisions
Types of hubs: Passive Intelligent Standalone Stackable
49
50
REPEATERS AND HUBS (CONTINUED)
Trung tâm (tiếp theo):Thiết bị kết nối chia sẻ cùng một lượng băng thông và va chạm cùng một miềnLuận lý và vật lý phải có sự khác biệ qua phân đoạn mạng Ethernet mà trên đó tất cả các thiết bị tham gia phải phát hiện và để tránh dữ liệu va chạmCác loại trung tâm:thụ độngthông minhđộc lậpstackable
50
51
BRIDGES
Connect two network segments Analyze incoming frames
Make decisions about where to direct them based on each frame’s MAC address
Operate at Data Link layer Protocol independent
Can move data more rapidly than traditional routers Extend Ethernet network without extending collision
domain or segment Can be programmed to filter out certain types of
frames
51
52
BRIDGES
Kết nối hai phân đoạn mạngPhân tích khung đếnĐịa chỉ MAC của mỗi khung là nền để quyết định trực tiếp về kết nốiHoạt động ở lớp liên kết dữ liệuGiao thức độc lậpCó thể di chuyển dữ liệu nhanh hơn so với các bộ định tuyến truyền thốngMở rộng mạng Ethernet mà không cần mở rộng phân khúc hoặc gia tăng va chạmCó thể được lập trình để lọc ra một số loại khung hình
52
53
SWITCHES
Subdivide network into smaller logical pieces (segments) Can operate at levels 2, 3, or 4 of OSI model Multiport bridges Most have internal processor, OS, memory, and
several ports Each port on switch acts like bridge Each connected device effectively receives own
dedicated channel
53
54
Chia thành nhiều mạng con luận lý nhỏ hơn, phân đoạn mạng(segments)
Có thể thực hiện các cấp 2,3 hay 4 theo mô hình OSI
Nhiều cổng cầu nối Sử dụng hầu hết bộ xử lý, hệ điều hành, bộ nhớ
và các cổng. Mỗi cổng trên mạch chuyển như là một cầu Mỗi thiết bị hiệu ứng kết nối tự nhận như một
kênh
55
INSTALLING A SWITCH
55
Figure 5-20: Connecting a workstation to a switch
56
INSTALLING A SWITCH (CONTINUED)
56
Figure 5-21: A switch on a small network
57
CUT-THROUGH MODE
Switch running in cut-through mode reads frame’s header and decides where to forward the data before receiving the entire packet Cannot read FCS before transmission
Cannot detect corrupt packets Can detect Erroneously shortened packets Biggest advantage is speed
57
58
CUT-THROUGH MODE
Chuyển đổi chạy trong cắt giảm thông qua chế độ đọc tiêu đề của khung hình và quyết định nơi để chuyển tiếp các dữ liệu trước khi nhận được gói toàn bộKhông thể đọc FCS trước khi truyềnKhông thể phát hiện các gói dữ liệu bị hỏngCó thể phát hiện sai lầm các gói dữ liệu ngắnLợi thế lớn nhất là tốc độ
58
59
STORE AND FORWARD MODE
Switch reads entire data frame into memory and checks for accuracy before transmitting Transmits data more accurately Slower than cut-through mode Can transfer data between segments running
different transmission speeds
59
60
STORE AND FORWARD MODE
Bộ chuyển đổi đọc toàn bộ khung dữ liệu vào bộ nhớ và kiểm tra về tính chính xác trước khi truyềnTruyền dữ liệu chính xác hơnChậm hơn so với chế độ cắt-thông quaCó thể chuyển dữ liệu giữa các phân đoạn chạy tốc độ truyền dẫn khác nhau
60
61
USING SWITCHES TO CREATE VLANS
Virtual LANs (VLANs) logically separate networks within networks
Use switches to group a number of ports into a broadcast domain Combination of ports making up a Layer 2 segment
In TCP/IP, referred to as a subnet
VLANs created by properly configuring switch’s software
VLAN configuration requires careful planning
61
62
USING SWITCHES TO CREATE VLANS
Các mạng LAN ảo (VLAN) một mạng lưới luận lý riêng biệt trong mạng lướiSử dụng các thiết bị chuyển mạch nhóm với một số cổng vào quảng bá miền Sự kết hợp của các cổng làm cho một Layer 2 phân khúcTrong TCP / IP, được gọi là một mạng conVLAN được tạo ra bằng cách đúng cấu hình phần mềm chuyển đổiVLAN cấu hình yêu cầu lập kế hoạch cẩn thận
62
63
HIGHER-LAYER SWITCHES
Layer 3 switches (routing switch) and Layer 4 switches
Ability to interpret higher-layer data enables switches to perform advanced filtering, statistics keeping, and security functions
63
64
HIGHER-LAYER SWITCHES
Lớp 3 bị chuyển mạch (switch định tuyến) và Layer 4 thiết bị chuyển mạchKhả năng để phiên dịch các lớp dữ liệu cao hơn cho phép các thiết bị chuyển mạch để thực hiện lọc nâng cao, thống kê, lưu giữ, và chức năng bảo mật
64
65
ROUTERS
Multiport connectivity devices that direct data between nodes on a network Can integrate LANs and WANs
Running at different transmission speeds Using variety of protocols
Reads incoming packet’s logical addressing information Determines where to deliver packet Determines shortest path to that network
Operate at Network layer Protocol-dependent
65
66
ROUTERS
Thiết bị nhiều cổng kết nối trực tiếp dữ liệu giữa các nút trên mạngCó thể tích hợp các mạng LAN và WANChạy ở tốc độ truyền dẫn khác nhauSử dụng nhiều giao thứcĐọc gói dữ liệu đến, địa chỉ thông tin logicXác định nơi để cung cấp các gói tinXác định con đường ngắn nhất để mạngHoạt động ở lớp mạngPhụ thuộc vào giao thức
66
67
ROUTER FEATURES AND FUNCTIONS
Typical router has internal processor, OS, memory, various input and output jacks, and management console interface
Modular router: multiple slots to hold different interface cards or other devices
All routers can: Connect dissimilar networks Interpret Layer 3 addressing and other information Determine the best path for data to follow Reroute traffic
67
68
Bộ định tuyến điển hình có bộ vi xử lý nội bộ, hệ điều hành, bộ nhớ và giắc cắm đầu ra, đầu vào khác nhau, và giao diện điều khiển giao diện quản lýModular router: nhiều khe để giữ thẻ giao diện khác nhau hoặc các thiết bị khácTất cả các router có thể:Kết nối mạng không tương tựPhiên dịch địa chỉ lớp 3 và các thông tin khácXác định đường đi tốt nhất cho dữ liệu theoĐịnh tuyến lại lưu lượng truy cập
69
ROUTER FEATURES AND FUNCTIONS (CONTINUED)
Other router functions: Filter out broadcast transmissions Prevent certain types of traffic from getting to a
network Support simultaneous local and remote connectivity Provide high network fault tolerance through
redundant components Monitor network traffic and report statistics Diagnose internal or other connectivity problems
69
70
ROUTER FEATURES AND FUNCTIONS (CONTINUED)
Các bộ định tuyến chức năng khác:Lọc ra các truyền dẫn quảng báNgăn chặn một số loại giao thông nhận được từ một mạngHỗ trợ đồng thời kết nối địa phương và từ xaCung cấp dung sai lỗi mạng cao thông qua các thành phần dư thừaĐiều khiển truyền thông mạng và báo cáo thống kêChẩn đoán các vấn đề kết nối nội bộ hoặc khác
70
71
ROUTER FEATURES AND FUNCTIONS (CONTINUED)
Interior router directs data between nodes on autonomous LANs
Exterior router directs data between nodes external to given autonomous LAN
Border routers connect autonomous LAN with a WAN
Static routing: network administrator programs router to use specific paths between nodes
Dynamic routing automatically calculates best path between two nodes Accumulates information in routing table
71
72
ROUTER FEATURES AND FUNCTIONS (CONTINUED)
Định tuyến trực tiếp từ trong các dữ liệu giữa các nút trên mạng LAN tự độngĐịnh tuyến trực tiếp bên ngoài các dữ liệu giữa các nút bên ngoài trên mạng LAN tự độngĐịnh tuyến biên tự động kết nối mạng LAN với một mạng WANĐịnh tuyến tĩnh: chương trình quản trị mạng định tuyến để sử dụng đường dẫn cụ thể giữa các nútĐịnh tuyến năng động tự động tính toán đường đi tốt nhất giữa hai nútTích luỹ thông tin trong bảng định tuyến
72
73
ROUTER FEATURES AND FUNCTIONS (CONTINUED)
73
Figure 5-24: The placement of routers on a LAN
74
ROUTING PROTOCOLS: RIP, OSPF, EIGRP AND BGP
Best path: most efficient route between nodes Routers communicate via routing protocols
Characterized according to convergence time Time taken to recognize best path
Routing Information Protocol (RIP) for IP and IPX Open Shortest Path First (OSPF) for IP Enhanced Interior Gateway Routing Protocol (EIGRP)
for IP, IPX, and AppleTalk Border Gateway Protocol (BGP) for IP
74
75
ROUTING PROTOCOLS: RIP, OSPF, EIGRP AND BGP
Con đường tốt nhất: tuyến đường hiệu quả nhất giữa các nútThiết bị định tuyến giao tiếp thông qua giao thức định tuyếnĐặc trưng theo thời gian hội tụThời gian thực hiện để nhận ra con đường tốt nhấtRouting Information Protocol (RIP) cho IP và IPXOpen Shortest Path First (OSPF) cho IPMở rộng cổng trong Gateway Routing Protocol (EIGRP) cho IP, IPX, AppleTalkBorder Gateway Protocol (BGP) cho IP
75
76
BROUTERS
Bridge routers Routers that take on some characteristics of
bridges Can forward nonroutable protocols Connect multiple network types through one device
76
77
BROUTERS
Cầu các bộ định tuyếnBộ định tuyến mà phải có một số đặc điểm như là cầuGiao thức chuyển tiếp không định tuyếnKết nối nhiều loại mạng thông qua một thiết bị
77
78
GATEWAYS
Connect two systems using different formatting, communications protocols, or architecture Repackage information to be read by another system
Operates at multiple OSI Model layers E-mail gateway Internet gateway LAN gateway Voice/data gateway Firewall
78
79
GATEWAYS
Kết nối hai hệ thống bằng cách sử dụng định dạng khác nhau, giao thức truyền thông, hoặc kiến trúcĐóng gói lại thông tin được đọc bởi một hệ thống khácHoạt động ở nhiều lớp mô hình OSIE-mail gatewayInternet gatewayLAN cửa ngõThoại / dữ liệu cổngFirewall
79
80
SUMMARY
Network adapters come in a variety of types depending on access method, network transmission speed, connector interfaces, type of compatible motherboard, and manufacturer
Desktops or tower PCs may use an expansion card NIC, which must match the system’s bus
NICs are designed to be used with either wire-bound or wireless connections
Firmware combines hardware and software Repeaters are the connectivity devices that
perform the regeneration of a digital signal
80
81
SUMMARY (CONTINUED)
A hub contains multiple data ports into which the patch cables for network nodes are connected
Bridges resemble repeaters in that they have a single input and a single output port, but they can interpret the data they retransmit
As nodes transmit data through a bridge, the bridge establishes a filtering database
Switches subdivide a network into smaller, logical pieces
81
82
SUMMARY (CONTINUED)
A router is a multiport device that can connect dissimilar LANs and WANs running at different transmission speeds, using a variety of protocols
Routers are protocol-dependent Routing protocols provide rules for
communication between routers and help them determine the best path between two nodes
Gateways are combinations of networking hardware and software that connect two dissimilar kinds of networks
82
top related