output impedance matching for trf79xxa (single and dual channel receive examples, with potential...
Post on 24-Dec-2015
217 Views
Preview:
TRANSCRIPT
Output Impedance Matching for TRF79xxA(single and dual channel receive examples, with potential improvement to existing
match)
Texas Instruments S2 MCU NFC/RFID Applications/Systems Team
Background / Problem being solved
• Need for impedance match for TRF79xxA devices which are utilizing only one of the RX channels and still operates with 50Ω antenna.
• This impedance match must transform a source resistance of 4Ω to a 50Ω load.
Calculations• Math for L Network low pass filter impedance match follows. • We start by calculating the Q of the legs, using the known values of the load and
source.
Where: QS = Q of the series leg
QP = Q of the parallel (shunt) leg
RL = Resistance of the load, in this case = 50Ω
RS = Resistance of the source, in this case Pin 5 of TRF79xxA (RDSON = ~4Ω)
Calculations (cont.)• Using XS and XP, we can now calculate L and C values needed for the impedance match circuit.
Calculated circuit values populated and plotted on Smith Chart
• Using L and C values calculated, we can simulate (using Smith chart) and see that the result produces the desired transformation from 4Ω to 50Ω
How do we get there with math?Single RX Channel Matching Calc
Qs 3.391164992Qp 3.391164992Rp (antenna connection) 50Rs (TRF79xxA Pin 5) 4
Qs = Qp = sqrt of (Rp/Rs - 1) 3.391164992Xs = Qs * Rs 13.56465997 Xp = Rp / Qp 14.74419562
L 159.3E-9 move to standard value of 150nHC 796.5E-12 move to standard value of 1500pF + 100pF (in parallel), in series with same for voltage divider presentation to RXIN_1
Standard component value circuit populated and simulated on Smith Chart
• Using standard L and C values, closest to what was calculated, we can simulate again (using Smith chart) and see that the result produces similar desired transformation from 4Ω to 50Ω
Results!
• Increase in read range with ISO15693 (+1cm), ISO14443A & B (+0.5cm) versus standard USB Dual RX EVM.
Background
• TRF79xxA devices have single transmit (TX) out and two receive (RX) channels.
• Impedance match from TX_OUT pin of TRF79xxA device to a single ended 50Ω 13.56MHz resonant antenna circuit is desired.
• Dual receive inputs need consideration for both voltage input and phase relationship to each other.
• The following slides will explain the basic theory and practical implementation of these requirements.
Simulated Ideal Match from 4Ω to 50Ω @ 13.56MHz
Note: Ideal circuit, there are no DC blocking caps and non-standard component values are shown
Simulated Practical Match from 4Ω to 50Ω @ 13.56MHz
Note: Practical circuit, as we inserted DC blocking caps and used standard component values
Simulation of actual (also practical) match from 4Ω to 50Ω @ 13.56MHz
Note: Actual circuit populated on EVM, as we inserted DC blocking caps and used standard component values
Improved Matching circuit using standard values
• 680pF in first L section changes to 560pF, this allows us to get to 50Ω point later.• 100pF + 27pF change to 82pF (reduction in BOM), this allows us to hit 50Ω and not over
shoot the target impedance.
How do we get there with math?Dual RX Channel Matching Calc
Qs 2.061552813Qp 2.061552813Rp (antenna connection) 21 to midpointRs (TRF79xxA Pin 5) 4 from TRF79xxA
Qs = Qp = sqrt of (Rp/Rs - 1) 2.061552813Xs = Qs * Rs 8.246211251
Xp = Rp / Qp 10.18649625
L 96.8E-9 because of DC block, need to move to 150nH C 1152.8E-12 use 560pF in parallel with existing 1200pF in series to get close enough
Qs 1.175139303Qp 1.175139303Rp (antenna connection) 50 to antenna connectionRs (midpoint) 21 midpoint
Qs = Qp = sqrt of (Rp/Rs - 1) 1.175139303Xs = Qs * Rs 24.67792536
Xp = Rp / Qp 42.54814717
L 289.8E-9 move to 330nH (standard value)C 276.0E-12 use 82pF in parallel with existing 220pF, 680pF in series with each other
NOTE: the final C value can be adjusted for the actual PCB circuit implementation
top related