pi kopftraeger rev 2015-07-20
Post on 25-Feb-2018
216 Views
Preview:
TRANSCRIPT
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
1/124
10.2014
Sommiers pour ponts roulants suspendus et poss
Informations sur le produit
Hnge- und Laufkrankopftrger
Produktinformation
Endcarriages for Suspension and O.H.T. Cranes
Product Information
HL LE
LS
LT
HT
Rev. 20.07.15
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
2/124
HL-T_
LS-T.F
M
2 10.14
Gltigkeit
Die vorliegende Auflage derProduktinformation fr Hnge-und Laufkrankopftrger ist ab
10.2014 gltig und ersetzt damitalle vorigen Produktinformatio-nen.
STAHL CraneSystems steht frWeiterentwicklung, Verbesse-rung und Innovation. Aus diesemGrund mssen wir uns nderun-gen der technischen Daten,Mae, Gewichte, Konstruktions-zeichnungen sowie der Lieferter-mine vorbehalten.Die Abbildungen dienen der
anschaulichen Information, sindjedoch nicht verbindlich.Irrtmer und Druckfehler sindvorbehalten.
Diese Produktinformation dientzur manuellen Auslegung vonKopftrgern. Die Ergebnisse kn-
nen von denen aus Konfigura-tionsprogrammen abweichen.
Validity
This edition of the ProductInformation brochure forendcarriages for suspension and
overhead travelling cranes is validfrom 10.2014 and supersedes allprevious product informationbrochures.
STAHL CraneSystems stands forfurther development,improvement and innovation.We must therefore reserve theright to modify technical data,dimensions, weights, designdrawings and delivery dates.The drawings serve to illustratethe products but are not binding.
Errors and printing errors areexcepted.
This Product Information bro-chure permits the manual config-uration of endcarriages. The
results may differ from those pro-vided by configuration programs.
Validit
Cette dition des Informations surle produit pour les sommiers pourponts roulants suspendus et
poss est valable partir de10.2014 et remplace ainsi toutesInformations sur le produit prc-dentes.
STAHL CraneSystems signifiel'volution, le perfectionnement etl'innovation. Par consquencenous devons nous rserver ledroit de modifier les caractri-stiques techniques, dimensions,poids, les plans de constructionainsi que les dlais de livraison.Les illustrations servent la clart
de linformation, mais ne revtentpas de caractre obligatoire.Sous rserve derreurs et defautes dimpression.
Ces Informations sur le produitservent calculer manuellementles sommiers. Les rsultats peu-
vent diffrer de ceux qu'on obtientd'un programme de configuration.
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
3/124
HL-T_
LS-T.F
M
10.14 3
Inhalt Table of contents Table des matires
Hngekrankopftrger Endcarriages for SuspensionCranes
Sommiers pour ponts roulantssuspendus 1
Laufkrankopftrger Endcarriages for O.H.T. Cranes Sommiers pour ponts roulantsposs 2
Sonstige Komponenten Other Components Autres composants
3
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
4/124
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
5/124
Hngekrankopftrger _Produktinformation
Endcarriages for Suspension Cranes _
Product Information
Sommiers pour ponts roulants suspendus _
Informations sur le produit
1
HL
HT
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
6/124
HL-T_
01.F
M
6 10.14
HngekrankopftrgerEndcarriages for suspension cranesSommiers pour ponts roulants suspendus
HL
HT
Mit den HngekrankopftrgernHL/HT knnen moderne Hnge-krane bis zu einer Tragfhigkeitvon 16.000 kg bzw. 20.000 kg beikleinen Spannweiten gebaut wer-
den.
Nutzen Sie die robuste Konstruk-tion, kompakte Bauweise, War-tungsfreundlichkeit und Zuver-lssigkeit in Verbindung mit denwirtschaftlichen Vorteilen derSerienfertigung fr Ihren Kran-bau.
Modern small-span suspensioncranes up to a working load of16,000 kg or 20,000 kg can bemanufactured on the basis ofHL/HT endcarriages for suspen-
sion cranes.
Make use of their sturdy design,compact construction, mainte-nance friendliness and reliabilityin conjunction with the economicadvantages of series productionfor your crane manufacturing.
Avec les sommiers pour pontsroulants suspendus HL/HT, il peuttre construit des ponts roulantssuspendus modernes ayant unecharge d'utilisation allant jusqu'
16.000 kg resp. 20.000 kg et desportes basses.
Profitez de la constructionrobuste et compacte, de la facilitd'entretien et de la fiabilit allantde pair avec les avantages co-nomiques de la fabrication ensrie pour votre construction deponts roulants.
Symbole Symbols Symboles
Maximale Tragfhigkeit [kg] Maximum working load [kg] Charge maximale dutilisation [kg]
Gewicht [kg] Weight [kg] Poids [kg]
Fahrgeschwindigkeit [m/min] Travel speed [m/min] Vitesse de dplacement [m/min]
Abmessungen siehe Seite .. Dimensions see page .. Dimensions voir page ..
Siehe Seite .. See page .. Voir page ..
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
7/124
HL-T_
01.F
M
10.14 7
HngekrankopftrgerEndcarriages for suspension cranes
Sommiers pour ponts roulants suspendus
1
Inhaltsverzeichnis Table of contents Table des matires
Symbole..............................................6 Symbols..............................................6 Symboles ............................................6
1 Die Technik im berblick............... 8 Technical features at a glance......8 La technique en un coup doeil......81.1 Ausstattung........................................8 Equipment ..........................................8 quipement.........................................81.2 Typenbezeichnung.......................... 10 Type designation............................. 10 Dsignation du type........................10
2 Auswahlanleitung..........................11 Selection instructions................... 11 Instructions pour la slection ......112.1 Grobauswahl ...................................11 Rough determination...................... 11 Dtermination approximatif...........112.2 Bestimmung der Kopftrgergre11 Determination of endcarriage size 11 Dtermination de la taille du som-
mier....................................................112.3 Bestimmung des Fahrantriebs...... 11 Determination of travel drive........11 Dtermination de l'entranement..112.4 Bestimmung des Kranpuffers.......11 Determination of crane buffer......11 Dtermination du butoir.................112.4.1 Pufferauswahltabelle.....................12 Buffer selection table ....................12 Slection du butoir..........................122.5 Fahrbahnendanschlge.................12 Runway end stops .......................... 12 Butes de fin de chemin de roule-
ment...................................................122.6 Erklrung der Abkrzungen ..........13 Explanation of abbreviations........ 13 Explication des abbrviations.......13
3 Abmessungen..................................14 Dimensions...................................... 14 Dimensions......................................14Hngekrankopftrger Endcarriages for suspension
cranesSommiers pour ponts roulantssuspendus
HL08...................................................14 HL08 .................................................. 14 HL08 ...................................................14HL10...................................................16 HL10 .................................................. 16 HL10 ...................................................16HL13...................................................18 HL13 .................................................. 18 HL13 ...................................................18HL20...................................................20 HL20 .................................................. 20 HL20 ...................................................20HT10 ..................................................22 HT10 .................................................. 22 HT10...................................................22HT13 ..................................................24 HT13 .................................................. 24 HT13...................................................24HT20 ..................................................26 HT20 .................................................. 26 HT20...................................................26
4 Optionen...........................................28 Options............................................. 28 Options..............................................28
4.1 Lackierung/Korrosionsschutz.......28 Paint/corrosion protection............ 28 Peinture/protection anticorrosive. 284.2 Pufferverlngerung ........................29 Buffer extension ............................. 29 Rallonge de butoir...........................294.3 Horizontale Fhrungsrollen...........30 Horizontal guide rollers ................. 30 Galets de guidage horizontaux .....304.4 Vertikale Fhrungsrollen ...............31 Vertical guide rollers...................... 31 Galets de guidage verticaux..........314.5 Erdungsbrste (Schienenrumer). 32 Earth brush (rail sweep)................32 Balai de mise la terre (balai de
rail).....................................................324.6 Montagehilfe...................................32 Assembly help tool.........................32 Dispositif de montage.....................324.7 Verdrehsicherung...........................33 Anti-skew support..........................33 Scurit antirotation.......................33
5 Technische Daten........................... 34 Technical data................................ 34 Caractristiques techniques ........345.1 bersicht Kopftrgeranschluss-
kombinationen.................................34Summary of endcarriage connec-
tion combinations........................... 34Vue densemble des combinaisonsdes fixations de sommier...............34
5.2 Zulssige ideelle Ecklasten ausLagerlebensdauer...........................34
Permissible ideal corner loads cal-culated on the basis of bearing life34
Charges angulaires idales admis-sibles selon la dure de vie des
paliers................................................345.2.1 HL08...................................................34 HL08 .................................................. 34 HL08...................................................345.2.2 HL/HT10 ............................................ 34 HL/HT10............................................ 34 HL/HT10.............................................345.2.3 HL/HT13 ............................................ 34 HL/HT13............................................ 34 HL/HT13.............................................345.2.4 HL/HT20 ............................................ 34 HL/HT20............................................ 34 HL/HT20.............................................34
Technische nderungen, Irrtmer undDruckfehler vorbehalten.
Subject to technical modifications,errors and printing errors excepted.
Sous rserve de modifications techni-ques, derreurs et de fautes dimpres-sion.
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
8/124
HL-T_
01.F
M
8 10.14
HngekrankopftrgerEndcarriages for suspension cranesSommiers pour ponts roulants suspendus
Die Technik im berblickTechnical features at a glanceLa technique en un coup doeil
1 Die Technik im berblick Technical features at a glance La technique en un coup doeil
HL
HT
Mit den Hngekrankopftrgernknnen Sie leicht und einfachmoderne Hngekrane bauen.Moderne Fertigungsverfahrenund unser zertifiziertes Qualitts-sicherungssystem nach DIN ISO9001/ EN 29001 garantieren einegleichbleibende Qualitt undMahaltigkeit.
You can build modern suspensioncranes simply and easily with thesuspension crane endcarriages.Modern manufacturing methodsand our certified Quality Assur-ance System to DIN ISO 9001/EN 29001 guarantee consistentquality and dimensional accuracy.
Avec les sommiers pour pontsroulants suspendus, vous pouvezconstruire facilement et simple-ment des ponts roulants suspen-dus modernes.Nos techniques de productionmodernes et notre systme decontrle certifi selon les normesDIN ISO 9001/ EN 29001 garantis-
sent une qualit et une tenue decotes constantes.
1.1 Ausstattung Equipment quipement
Kopftrger (1) Stahlkonstruktion mit hoher
geometrischer Genauigkeit. Laufrder aus Kugelgraphit-
guss. Die hervorragendenSelbstschmiereigenschaftendes LaufradwerkstoffsEN-GJS-700-2 sorgen fr eine
hohe Lebensdauer des Rad-/Laufbahn-Systems.
Geringe Kranbahntrgerbelas-tung. Geringe Unterflanschbie-gung durch ein optimiertesLaufradprofil ermglicht denEinsatz kleinerer Kranbahntr-ger.
Einfache Einstellung auf dasKranbahnprofil ber Abstands-teile.
Endcarriage (1) Steel structure with a high
degree of geometrical accu-racy.
Wheels of spheroidal graphitecast iron. The excellent self-lubricating properties of thewheel material EN-GJS-700-2
ensure a long service life ofthe wheel/runway system.
Minimum load on crane run-way beam. Only slight deflec-tion of the bottom flangethanks to an optimized wheelprofile, enabling the use ofsmaller crane runway beams.
Simple adjustment to cranerunway section using spacerparts.
Sommier (1) Construction d'acier avec une
grande prcision gomtrique. Galets en fonte graphite
sphrodale. Les excellentesproprits autolubrifiantes dela matire des galets EN-GJS-700-2 garantissent une grande
longvit du systme galet/chemin de roulement.
Raction minimale sur la pou-tre du chemin de roulement. Lacourbure minimale de lasemelle infrieure obtenue parun profil de galet spcial, per-met l'utilisation de poutresplus petites pour le chemin deroulement.
Rglage simple au profil de lavoie de roulement du pont.
c1708v01
3 1 2
c1709v01
3 1 2
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
9/124
HL-T_
01.F
M
10.14 9
Die Technik im berblickTechnical features at a glanceLa technique en un coup doeil
HngekrankopftrgerEndcarriages for suspension cranes
Sommiers pour ponts roulants suspendus
1
Krananschluss (2) Hochfeste formschlssige Ver-
bindung zwischen Kranbrckeund Kopftrgern.
Fahrantrieb (3) Robuster Laufradantrieb mit
gekapselter und fettge-schmierter Laufradverzah-nung.
Lebensdauerschmierung. Auslegung nach FEM/ISO M4. Bremsmotor mit Scheiben-
bremse und Schwungmasse.Komfortables Anfahr- undBremsverhalten fr minimales
Lastpendeln. Isolierstoffklasse F nach
EN/IEC 60034. Die Motoren sind mit elektri-
scher Steckverbindung(Anbausteckdose) ausgers-tet.
Sehr geruscharm durchSchrgverzahnung allerGetriebestufen.
Fahrgeschwindigkeiten wahl-weise mit polumschaltbarenMotoren im Verhltnis 1:4 oder1:10 mit 4-poligen Motoren und
Frequenzumrichter.
Crane connection (2) High-tensile positive-locking
connection between cranegirder and endcarriages.
Travel drive (3) Robust wheel drive with
enclosed, grease-lubricatedwheel gearing.
Lifetime lubrication. Design acc. to FEM/ISO M4. Brake motor with disc brake
and centrifugal mass. Smoothacceleration and braking char-acteristics for minimum loadswing.
Insulation class F toEN/IEC 60034.
Motors are equipped with aplug connection (socket).
Very little noise due to helicalgearing of all gear steps.
Travel speeds as desired withpole-changing motors at aratio of 1:4 or with 4-polemotors and frequency inverterat a ratio of 1:10.
Fixation du pont roulant (2) Fixation de la poutre porteuse
au sommier par une liaisonmcanique haute rsistance.
Groupe d'entranement (3) Entranement direct des galets
avec denture des galets prot-ge par cache et lubrifie lagraisse.
Graissage vie. Conception selon FEM/ISO M4. Moteur-frein avec frein dis-
que et masse centrifuge. Frei-nage et roulement doux pourminimaliser l'oscillation de la
charge. Classe d'isolation F selon
EN/IEC 60034. Les moteurs commutation de
polarit sont quips d'uneconnexion lectrique parfiches (prise de raccorde-ment).
Trs silencieux grce la den-ture hlicodale tous les ta-ges.
Vitesses de translation faculta-tives avec moteurs commu-tation de polarit, rapport de
transmission 1 : 4, ou avecmoteurs 4 ples et convertis-seur de frquence, rapport detransmission 1 : 10.
c1584v01
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
10/124
HL-T_
01.F
M
10 10.14
HngekrankopftrgerEndcarriages for suspension cranesSommiers pour ponts roulants suspendus
Die Technik im berblickTechnical features at a glanceLa technique en un coup doeil
1.2 Typenbezeichnung Type designation Dsignation du type
HL/HT
1,2 KopftrgertypHL/HT =Hngekrankopftrger
3,4 Laufraddurchmesser x 1008 = 80 mm, 10 = 100 mm13 = 125 mm, 20 = 200 mm
5 Anschlussbeschreibung- = mittig (Standard)B = gekoppelte KopftrgerC = auermittig (Sonder)
6,7 Radstand x 10012 = 1200 mm, 14 = 1400 mm ...40 = 4000 mm
8-10 Flanschbreite073-313 (HL08)082-322 (HL/HT10)
100-343 (HL/HT13)127-418 (HL/HT20)11 Anzahl Fahrantriebe
- = 1 Antrieb pro Kopftrger(Standard)
D = 2 Antriebe pro Kopftrger12-14 Anschluss (mit/ohne Anschluss-
platte)SA3 / BA1-3 (HL08)SB4 / BB2-5 (HL10)SC3-5 / BC3-5 (HL13)SD3-5 / BD3-5 (HL20)HB4 / KB2-5 (HT10)HC3-5 / KC3-5 (HT13)HD3-5 / KD3-5 (HT20)Anschluss geschweit(bauseits)WA_ (HL08)WB_ (HL10)WC_ (HL13)WD_ (HL20)
15-18 Abstand Anschlussplatte0000 = Standard, mittiger
Anschluss#### = Eintrgerhngekran,
auermittiger Anschluss(Abstand Aufhngebol-zen bis BohrungAnschluss)
#### = Zweitrgerhngekran(Bohrungsabstand zwi-schen den Anschlssen)
19 Puffertyp
A, B, C, D = GummipufferK, G, E, M, F, H, P =Polyurethanpuffer
0 = ohne Puffer20-23 0000 = bei Kopftrgerpaar
(Standard)#### = Abstand der inneren
Aufhngebolzen beigekoppelten Kopftrgern
24 Lackierung- = grundiert 60 m (Standard)K = DecklackE = Sonder
25 AusfhrungN = Standard, ohne OptionenE = Sonder, mit Optionen
1,2 Type of endcarriageHL/HT =Endcarriage for suspen-
sion crane3,4 Wheel diameter x 10
08 = 80 mm, 10 = 100 mm13 = 125 mm, 20 = 200 mm
5 Connection description- = Centre (standard)B = Coupled endcarriagesC = Off-centre (off-standard)
6,7 Wheelbase x 10012 = 1200 mm, 14 = 1400 mm ...40 = 4000 mm
8-10 Flange width073-313 (HL08)
082-322 (HL/HT10)100-343 (HL/HT13)127-418 (HL/HT20)
11 Number of travel drives- = 1 drive per endcarriage
(standard)D = 2 drives per endcarriage
12-14 Joint (with/without joint plate)SA3 / BA1-3 (HL08)SB4 / BB2-5 (HL10)SC3-5 / BC3-5 (HL13)SD3-5 / BD3-5 (HL20)HB4 / KB2-5 (HT10)HC3-5 / KC3-5 (HT13)HD3-5 / KD3-5 (HT20)Welded joint (by customer)WA_ (HL08)WB_ (HL10)WC_ (HL13)WD_ (HL20)
15-18 Spacing between joint plates0000 = Standard, centre con-
nection#### = Single girder suspen-
sion crane, off-centreconnection (distancebetween suspension boltand hole in joint plate)
#### = Double girder suspen-sion crane (hole separa-
tion betweenconnections)
19 Buffer type
A, B, C, D = Rubber buffersK, G, E, M, F, H, P =Polyurethane buffers
0 = Without buffers20-23 0000 = On pair of endcarriages
(standard)#### = Distance between inside
suspension bolts forcoupled endcarriages
24 Paint- = Primer coat 60 m
(standard)K = Top coatE = Off-standard
25 VersionN = Standard, without optionsE = Off-standard, with options
1,2 Type de sommierHL/HT =Sommier pour pont
roulant suspendu3,4 Diamtre du galet x 10
08 = 80 mm, 10 = 100 mm13 = 125 mm, 20 = 200 mm
5 Description de la connexion- = centre (standard)B = sommiers couplsC = excentre (spciale)
6,7 Empattement x 10012 = 1200 mm, 14 = 1400 mm ...40 = 4000 mm
8-10 Largeur daile073-313 (HL08)
082-322 (HL/HT10)100-343 (HL/HT13)127-418 (HL/HT20)
11 Nombre des entranements- = 1 entranement par
sommier (standard)D = 2 entranements par sommier
12-14 Connexion (avec/sans plaquede fixation)SA3 / BA1-3 (HL08)SB4 / BB2-5 (HL10)SC3-5 / BC3-5 (HL13)SD3-5 / BD3-5 (HL20)HB4 / KB2-5 (HT10)HC3-5 / KC3-5 (HT13)HD3-5 / KD3-5 (HT20)Connexion soude (par le client)WA_ (HL08)WB_ (HL10)WC_ (HL13)WD_ (HL20)
15-18 cart de la plaque de fixation0000 = Standard, connexion
centre#### = Pont roulant suspendu
monopoutre, connexionexcentre (cart entreboulon de suspension etforage de la plaque defixation)
#### = Pont roulant suspendubipoutre (cart entre lesforages des connexions)
19 Type de butoirA, B, C, D = Butoirs decaoutchouc
K, G, E, M, F, H, P =Butoirs de polyurthane
0 = Sans butoirs20-23 0000 = Sur sommiers coupls,
cart entre les boulonsde suspension intrieurs
24 Peinture- = Couche d'apprt 60 m
(standard)K = Couche de finitionE = Spciale
25 ExcutionN = Standard, sans optionsE = Spciale, avec options
H. 13 - 23 100 - SC4 0000 C 0000 - N1,2 3,4 5 6,7 8-10 11 12-14 15-18 19 20-23 24 25
= = c1710v01
c1710v02
800
c1710v03
1100
EintrgerhngekranSingle girder suspension cranePont roulant suspendu monopoutre
mittiger Anschlusscentre connectionconnexion centre
HL13-23100-SC4 0000C0000-N
auermittiger Anschlussoff-centre connectionconnexion excentre
HL13C23100-SC40800C0000-N
ZweitrgerhngekranDouble girder suspension cranePont roulant suspendu bipoutre
HL13-23100-SC4 1100C0000-N
20.07.15/
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
11/124
HL-T_
01.F
M
10.14 11
AuswahlanleitungSelection instructionsInstructions pour la slection
HngekrankopftrgerEndcarriages for suspension cranes
Sommiers pour ponts roulants suspendus
1
2 Auswahlanleitung Selection instructions Instructions pour la slection
2.1 Grobauswahl Rough determination Dtermination approximatif
2.2 Bestimmung der Kopftrgergre Determination of endcarriagesize
Dtermination de la taille dusommier
Bedingungen: Rmax Rzul vorh. L1 L1zul
Conditions: Rmax Rzul L1 existante L1zul
Conditions : Rmax Rzul actual L1 L1zul
2.3 Bestimmung des Fahrantriebs Determination of travel drive Dtermination de l'entranement
Bedingung: mFmax mF zul
Condition: mFmax mF zul
Condition : mFmax mF zul
2.4 Bestimmung des Kranpuffers Determination of crane buffer Dtermination du butoir
*1 Formel zur genauen Berechnung desKranpuffers.
Formula for exact calculation of cranebuffer.
Formule pour le calcul exact du butoirdu pont roulant.
*1 Last nicht gefhrtNot guided loadCharge non guide
Erklrung der Abkrzungen sieheSeite 13.
Explanation of abbreviationsseepage 13.
Explication des abbrviations voirpage 13.
5 10 15 20L1 [m]
kg
c1716v01
1000
1600
2000
3200
4000
5000
6300
8000
10000
1250016000
0
HL08
HL/HT10
HL/HT13
HL/HT20
mKr mT mZ mKo k g[ ]+ +=
RmaxmK r
4 100----------------
mL mKa+2 100
-------------------------
L1 L10( )L1
------------------------- kN[ ]+=
RminmKr
4 100----------------
mL mKa+2 100
-------------------------
L10L1-------- kN[ ]+=
2 x R
R Rk 0
c1707v01
L10L 1
b
D
mKr
mL
mKa
RRc0143v01
mF ma x mKr mKa mL kg[ ]+ +=
mpuvorhmKr
2---------- mKa L1 L10
L1-------------------- kg[ ]+=
mp uzu l2 E
zu l
vp u2----------------- kg[ ]=
vp u v kpu60
------------------ m s[ ]=
c1686v01
e
d
M
L10
L 1
b
D
mKr
mL
mKa
RRc0143v01
ege s 2 d mm[ ]
c1686v02
eges
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
12/124
HL-T_
01.F
M
12 10.14
HngekrankopftrgerEndcarriages for suspension cranesSommiers pour ponts roulants suspendus
AuswahlanleitungSelection instructions
Instructions pour la slection
2.4.1 Pufferauswahltabelle(Grobauswahl)
Buffer selection table(rough calculation)
Slection du butoir(slection approximatif)
Max. Fahrgeschwindigkeit v [m/min]Max. travel speed v [m/min]
Vitesse de dplacement max. v [m/min]Ohne Endschalter
Without limit switchesSans interrupteurs de fin de course
kpu = 0,85 10 12,5 16 20 25 32 40 50 63 80
Mit EndschalterWith limit switches
Avec interrupteurs de fin de course
kpu = 0,70 12,5 16 20 25 32 40 50 63 80 100
TypCodeTypeCode
PufferBufferButoir
MaterialMaterialMatriau
d e Ezul Zulssige Aufprallmasse mpu in [kg] fr max. Aufprallgeschwindigkeit vpu in [m/s]Permissible impact mass mpu in [kg] for max. impact speed vpu in [m/s]
Masse d'impact max. admissible mpu en [kg] pour vitesse d'impact max. vpu in [m/s][mm] [mm] [Nm] vpu
[m/s]0,15 0,19 0,23 0,29 0,37 0,47 0,58 0,74 0,93 1,17
A D1801 GummiRubberCaout-chouc
63 53 250
mpu[kg]
23500 14300 9100 5800 3500 2200 1400 900 500 300B D2240 80 68 400 37600 22900 14600 9400 5700 3600 2300 1400 900 500C D2241 100 85 1000 94000 57300 36700 23500 14300 9100 5800 3700 2200 1400D D2242 125 105 1600 150400 91800 58700 37600 22900 14600 9400 5900 3600 2300
K 80x80 Polyure-thanPolyure-thanePolyu-
rthane
80 80 400 37600 22900 14600 9400 5700 3600 2300 1400 900 500G 100x100 100 100 800 75200 45900 29300 18800 11400 7300 4700 2900 1800 1100E 100x150 100 150 1200 112800 68800 44000 28200 17200 11000 7000 4400 2700 1700M 125x125 125 125 1550 145700 88900 56900 36400 22200 14200 9100 5700 3500 2200F 125x190 125 190 2320 218100 133100 85200 54500 33200 21300 13600 8500 5300 3400H 160x160 160 160 3300 310300 189400 121200 77500 47300 30300 19300 12200 7500 4800P 160x240 160 240 4950 465500 284100 181800 116300 71000 45400 29000 18300 11300 7200
Max. zulssige Aufprallmasse beiStandardfahrgeschwindigkeiten(20 bzw. 40 m/min) und Endschalter
Max. permissible impact mass at stan-dard travel speeds (20 or 40 m/min)and with limit switches
Masse d'impact max. admissible avecvitesses de dplacement standard(20 ou 40 m/min) et interrupteurs de finde course
2.5 Fahrbahnendanschlge Runway end stops Butes de fin de chemin de roule-
ment
Die Hngekrankopftrger sindserienmig mit Puffern ausge-stattet. Passende Endanschlgesind bauseits anzubauen.
Die Gre der Anschlge ist ent-sprechend den Pufferkrften aus-zulegen (siehe Kapitel 3"Kran-puffer"). Die Abmessungen sind sozu whlen, dass die ganze Flchedes Puffers auf den Anschlagtrifft.
The suspension crane endcarria-ges are fitted with buffers as stan-dard. The stops required on thecrane bridge must be supplied bythe customer.
The size of the stops must beselected in accordance with thebuffer forces (see chapter 3"Crane buffers"). The dimensionsmust be selected so that thewhole surface of the buffer strikesthe stop.
Les sommiers pour ponts roulantssuspendus sont, en srie, qui-ps de butoirs. Des butes de finde course, fournir par le client,doivent tre montes.
Choisir la taille des butes enfonction des forces exerces parles butoirs (voir chapitre3 "Butoirsde ponts roulants"). Choisir lesdimensions de telle sorte quetoute la surface du butoirs'applique contre la bute.
Erklrung der Abkrzungen sieheSeite 13.
Explanation of abbreviationsseepage 13.
Explication des abbrviations voirpage 13.
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
13/124
HL-T_
01.F
M
10.14 13
AuswahlanleitungSelection instructionsInstructions pour la slection
HngekrankopftrgerEndcarriages for suspension cranes
Sommiers pour ponts roulants suspendus
1
2.6 Erklrung der Abkrzungen Explanation of abbreviations Explication des abbrviations
b [mm] Flanschbreite Flange width Largeur daileEzul [Nm] Zulssige Pufferenergie Permissible buffer energy nergie admissiblekpu Abminderungsfaktor Reduction factor Facteur de rductionL 1 [m] Spurmittenma Kran Crane span Porte du pont roulantL 10 [m] Anfahrma Katze Hook approach trolley Cote d'approche du chariotm F [kg] Fahrlast/Paar Travel load/pair Charge roulant/paire des sommiersm Ka [kg] Gewicht Katze Weight of trolley/crab Poids du chariotm Ko [kg] Gewicht Kopftrger + Anschluss-
platte + AntriebWeight of endcarriage + joint plate+ drive
Poids du sommier + plaque de fixation+ entranement
m Kr [kg] Gewicht Kran Weight of crane Poids du pont roulantm L [kg] Tragfhigkeit Working load Charge d'utilisationm T [kg] Gewicht Kranbrcke(n) Weight of crane bridge(s) Poids de la/des poutre(s) porteuse(s)m Z [kg] Gewicht Zusatzlasten Weight of additional loads Poids des charges additionnellesmpuvorh [kg] Vorhandene Aufprallmasse Actual impact mass Masse d'impact existantempuzul [kg] Zulssige Aufprallmasse Permissible impact mass Masse d'impact admissible D [mm] Laufrad-Durchmesser Wheel diameter Diamtre du galetRmax [kN] Vorhandene maximale Ecklast
(statisch)Max. actual corner load (static) Charge angulaire maximale par galet
(statique)R
zul[kN] Zulssige Ecklast (statisch) Permissible corner load (static) Charge angulaire admissible par galet
(statique)v [m/min] Fahrgeschwindigkeit Travel speed Vitesse de dplacementvpu [m/s] Aufprallgeschwindigkeit Impact speed Vitesse d'impact
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
14/124
HL-T_
02.F
M
14 10.14
HngekrankopftrgerEndcarriages for suspension cranesSommiers pour ponts roulants suspendus
AbmessungenDimensionsDimensions
Dimensions
You will find the respective corner
loads on page 34.
Dimensions
Vous trouvez les charges angulai-
res correspondantes page 34.
Die zugehrigen Ecklasten finden
Sie auf Seite 34.
3 Abmessungen
*1 Spannweite Kran*2 Gewicht pro Kopftrgerpaar ohne
Anschlussplatten*3 Max. zulssige Ecklast (2 Radpaare)*4 Bei geneigtem Flansch
*1 Crane span*2 Weight per pair of endcarriages without
joint plates*3 Max. permissible corner load (2 wheel
pairs)*4 With sloping flange
*1 Porte du pont roulant*2 Poids par paire de sommiers sans
plaques de fixaton*3 Charge angulaire max. admissible
(2 paires de galets)*4 Avec bride incline
c1701v01
"Z" 300 Nm
M16x70-10.9 ISO 4014
B B B
303
b
b + 52
26 41
80
30
b2
133
82
A - A
12,6 (17,0) *4
264
ProfilProfileProfil
KastenBox
Caisson
ProfilProfileProfil
18
m2
d
c1700v01
= =
k1
k0
e
m0
146
A
A
SA3
R
Z
R
min 220 min 220
BA1-3
Horizontale Bewegungsfreiheit Trger + 11 mmFree horizontal movement of the beam +11 mm
Plage de mouvement de la poutre + 11 mm
HL08
L1zul
*1
TypType
k0 k1
[m] [mm] [mm] *29 HL08-12 1200 1530 220
11 HL08-14 1400 1730 23414 HL08-18 1800 2130 26218 HL08-23 2300 2630 29621 HL08-28 2800 3130 330
TypType
Rzul[kN] *3
HL08 SA3 BA1 BA2 BA3-12 21,7 21,7 21,7 21,7
-14 21,7 21,7 21,7 21,7-18 21,7 18,5 21,7 21,7-23 20,0 14,5 20,0 20,0-28 17,4 11,9 16,7 17,4
b b2[mm] [mm]
73-120 306121-168 354169-216 402217-264 450265-313 498
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
15/124
HL-T_
02.F
M
10.14 15
AbmessungenDimensionsDimensions
HngekrankopftrgerEndcarriages for suspension cranes
Sommiers pour ponts roulants suspendus
1
Buffer
Calculation see "Buffer selectiontable"page 46.
Joint
With joint plate
Without joint plate
Travel drives
For more details, see Product
information "Travel drives".
Butoirs
Pour le calcul, voir "Slection dubutoir", page 46.
Connexion
Avec plaque de fixation
Sans plaque de fixation
Groupes dentranement
Pour de plus amples informa-
tions, voir Informations sur le pro-duit "Groupes dentranement".
Puffer
Auslegung siehe "Pufferauswahl-tabelle" Seite 46.
Anschluss
Mit Anschlussplatte
Ohne Anschlussplatte
Fahrantriebe
Nheres siehe Produktinforma-
tion "Fahrantriebe".
Typ CodeType Code PufferBufferButoir
MaterialMaterialMatriau
d e max. Federwegmax. deflectionmax. crasement
Ezul GewindeThreadFilet
[mm] [mm] [mm] [Nm]A D1801 Gummi
RubberCaoutchouc
63 53 30 250 M12x35 0,3B D2240 80 68 32 400 0,6C D2241 100 85 42 1000 1,2K 80x80 Polyurethan
PolyurethanePolyurthane
80 80 60 400 0,4G 100x100 100 100 75 800 0,6E 100x150 100 150 113 1200 0,8
SA3p1 [mm] 360
Bmin-max[mm] 160-300
Gewicht/weight/poids [kg] 31
BA1 BA2 BA3p1 [mm] 100 150 200
Bmin-max[mm] 154-203 204-253 254-320
D GetriebeGear
Rducteur
MotorMotor
Moteur
m0 m2
[mm] [mm]80 SDA2 8/2F12 396 89
8/2F134F18 89/137 *1
c1686v01
e
d
M
B
p1
c1702v01
350
90
450SA3
90
p1
B
c1702v02
BA1-3
*1 Elektrischer Anschluss steckbar *1 Plug-in electrical connection *1 Connexion lectrique enfichable
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
16/124
HL-T_
02.F
M
16 10.14
HngekrankopftrgerEndcarriages for suspension cranesSommiers pour ponts roulants suspendus
AbmessungenDimensionsDimensions
You will find the respective cornerloads on page 34.
Vous trouvez les charges angulai-res correspondantes page 34.
Die zugehrigen Ecklasten findenSie auf Seite 34.
*1 Spannweite Kran*2 Gewicht pro Kopftrgerpaar ohne
Anschlussplatten*3 Max. zulssige Ecklast (2 Radpaare)*4 Bei geneigtem Flansch
*1 Crane span*2 Weight per pair of endcarriages without
joint plates*3 Max. permissible corner load (2 wheel
pairs)*4 With sloping flange
*1 Porte du pont roulant*2 Poids par paire de sommiers sans
plaques de fixaton*3 Charge angulaire max. admissible
(2 paires de galets)*4 Avec bride incline
m2
d
c1700v02
= =
k1
k0
e
m
0 176
A
A
RR
min 250 min 250
SB4BB2-5
Z
c1701v02
"Z" 590 Nm
M20x70-10.9 ISO 4014
B B B
b
b + 51
25,5 41,5
100
35
b2
143
95
A - A
17,5 (23,0) *4
31,54
Profil
ProfileProfil
Kasten
BoxCaisson
Profil
ProfileProfil
358/378(k0
2300/3500)
315mm)
136
590 NmM20x110-10.9 ISO 4014
40
33,5:Spw
20-45
30:Spw
50-55
300 NmM16x90-10.9 ISO 4014
75
100
(SDB4)
(SDB5)
b1
k
125
15
20
250
135 135
c1576v05a
63
"X" "Y" A - A
h1
c1573v05a
=
min 305*
=
k1
k0
e
m0
Xd
A
A
F5-F8
H4-H9
m2
min 250*
Y
150
(155:h1=415)
F4
12
m1
b1 54 59 64 69 74 79 84 89 94 99k*3
40 45(A45)
50 55(A55)
60 65(A65)
70 75(A75)
80 85L1 b1[m] [mm]
L1 < 20 +020 < L1 < 30 +530 < L1 < 35 +10
TypType
h1
LT-25-20/25 315
LT-25-32/40 415
Anschluss seitlich/obenSide/top connectionFixation latrale/par le haut
Anschluss obenTop connectionFixation par le haut
LT-25
L1zul
*1
Typ
Type
k0 k1
[m] [mm] [mm] *215 LT-25-20 2000 2330 818
18,5 LT-25-25 2500 2830 90623,5 LT-25-32 3150 3480 115830 LT-25-40 4000 4330 1342
33,5 LT-25-45 4500 4830 1450
TypType
Rzul[kN]
F4 F4 F5
LT-25
-20 80,0 160,0 118,3-25 64,0 128,0 94,7-32 50,8 101,6 75,1-40 40,0 80,0 59,2-45 35,6 71,1 52,6
TypType
Rzul[kN]
F5 F7 F8
LT-25-20 160,9 160,9 160,9-25 148,7 148,7 148,7-32 147,8 147,8 147,8
-40 118,0 125,8 125,8-45 104,9 111,3 111,3
TypType
Rzul[kN]
LT-25 H4 H5 H7 H9-20 160,9 160,9 160,9 160,9-25 148,7 148,7 148,7 148,7-32 127,0 147,8 147,8 147,8-40 100,0 116,7 137,4 137,4-45 88,9 103,7 111,3 111,3
05.05.15/
* Ma nicht gltig bei Verwendung vonAbhebesicherung, Sturmsicherung
*1 Spannweite Kran*2 Gewicht pro Kopftrgerpaar ohne
Anschlussplatten*3 Bei Schienenbreiten45, 55 etc.
Hinweise in Abs. 5.3 beachten
* Dimension not applicable when usinganti-jump catch or storm lock device
*1 Crane span*2 Weight per pair of endcarriages without
joint plates*3 For rail widths45, 55, etc. observe notes
in section 5.3
* Dimension pas valable en cas dutilisa-tion dun dispositif anti-soulvement ouune scurit-tempte
*1 Porte du pont roulant*2 Poids par paire de sommiers sans
plaques de fixation*3 Respectez les remarques dans la section
5.3 pour les largeurs de rail 45, 55, etc.
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
61/124
LS-T_
02.F
M
10.14 61
AbmessungenDimensionsDimensions
Kopftrger fr EintrgerlaufkraneEndcarriages for single girder o.h.t. cranes
Sommiers pour ponts roulants poss monopoutre
2
Buffer
Calculation see "Buffer selectiontable"page 46.
Joint plates
Travel drives
For more details, see Product
information "Travel drives".
Butoirs
Pour le calcul, voir "Slection dubutoir", page 46.
Plaques de fixation
Groupes dentranement
Pour de plus amples informa-
tions, voir Informations sur leproduit "Groupes dentranement".
B B
c1763v01
b2
Profil KastenProfile BoxProfil Caisson
Puffer
Auslegung siehe "Pufferauswahl-tabelle" Seite 46.
Anschlussplatten
Fahrantriebe
Nheres siehe Produktinforma-
tion "Fahrantriebe".
Typ CodeType Code PufferBufferButoir
MaterialMaterialMatriau
d e max. Federwegmax. deflectionmax. crasement
Ezul GewindeThreadFilet
[mm] [mm] [mm] [Nm]B D2240 Gummi
RubberCaoutchouc
80 68 32 400 M12x35 0,6C D2241 100 85 42 1000 1,2D D2242 125 105 50 1600 2,3E 100x150 Polyurethan
PolyurethanePolyurthane
100 150 113 1200 0,8M 125x125 125 125 94 1550 1,1F 125x190 125 190 143 2320 1,4H 160x160 160 160 120 3300 2,6P 160x240 160 240 180 4950 3,5I 200x200 200 200 150 6400 4,5S 200x300 200 300 225 9600 6,2
F4 F5 F7 F8p1 [mm] 480 660 890 1030p2 [mm] 530 730 960 1100p3 [mm] 320 320 320 320
Bmin-maxProfil/profile/profil [mm] 230-350 350-410 - -
Bmin-maxKasten/box/caisson [mm] 300-410 410-520 520-750 750-890
b2maxoben/top/par le haut [mm] 370 490 720 860
b2maxseitlich/side/latrale [mm] 370 465 695 835
Gewicht pro Platte/weight per plate/poids par plaque [kg]
73 100 133 152
H4 H5 H7 H9p1 [mm] 590 700 920 1170p2 [mm] 640 750 970 1220p3 [mm] 280 280 280 280
Bmin-max[mm] 300-410 410-520 520-740 740-990Gewicht pro Platte/weight per plate/
poids par plaque [kg]34 40 52 66
D GetriebeGear
Rducteur
MotorMotor
Moteur
m0 m1 m2
[mm] [mm]250 SDB4 8/2F12 567 336 134
8/2F138/2F30 624 1548/2F314F18 567 1824F38 629 202
SDB5 8/2F30 661 415 1548/2F318/2F42 7414F38 666 2024F48
c1686v01
e
d
M
p3
p1
p2
B c1678v0115
B
p1
p2
p3
c1678v0252,55
p3
Bc1678v03
p1
p2
60
F4
F5-F8
H4-H9
/05.05.15
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
62/124
LS-T_
02.F
M
62 10.14
Kopftrger fr EintrgerlaufkraneEndcarriages for single girder o.h.t. cranesSommiers pour ponts roulants poss monopoutre
AbmessungenDimensionsDimensions
"Calculation of required railwidth k"see page 45.
You will find the respective wheelloads on page 108.
"Calcul de la largeur de rail nces-saire k", voir page 45.
Vous trouvez les charges pargalet correspondantes page 108.
"Ermittlung der erforderlichenSchienenbreite k"siehe Seite 45.
Die zugehrigen Radlasten findenSie auf Seite 108.
380/480
30h2
170
590 NmM20x130-10.9 ISO 4014
30
32
350
0
215
25
37
300 NmM16x80-10.9 ISO 4014
300 NmM16x80-10.9 ISO 4014
b1
k
20
315
c1576v06a
125 63
135 135
75
100
(SDB4)
(SDB5)
20
"X" "Y" A - A
h1
c1573v06
=
min 310/350* (k0>3150mm)
=
k1
k0
e
m0
X
150
d
A
A
Q4, Q6, Q8, Q0
K4-K9
m2
min 250/290* (k0>3150mm)
Y
Q3, Q5, Q7, Q9
14
m1
b1 64 69 74 79 84 89 94k*3
50 55(A55)
60 65(A65)
70 75(A75)
80L1 b1[m] [mm]
L1 < 20 +020 < L1 < 30 +530 < L1 < 35 +10
L1 > 35 +15
TypType
h1 h2
LT-32-25/32 370 20
LT-32-40/45 470 20
LT-32-50/55 545 95
Anschluss seitlich/obenSide/top connectionFixation latrale/par le haut
Anschluss obenTop connectionFixation par le haut
LT-32
L1zul
*1
Typ
Type
k0 k1
[m] [mm] [mm] *218,5 LT-32-25 2500 3000 107623,5 LT-32-32 3150 3650 124630 LT-32-40 4000 4500 1432
33,5 LT-32-45 4500 5000 154437,5 LT-32-50 5000 5500 179041 LT-32-55 5500 6000 1912
Typ
Type
Rzul[kN]
Q3 Q3 Q5 Q5
LT-32
-25 80,0 160,0 112,0 195,6-32 63,5 127,0 88,9 173,9
TypType
Rzul[kN]
LT-32 Q7 Q9-25 195,6 --32 173,9 173,9
TypType
Rzul[kN]
Q4 Q4 Q6 Q6
LT-32-40 58,3 116,7 79,2 158,3-45 51,9 103,7 70,4 140,7-50 46,7 93,3 63,3 126,7-55 42,4 84,8 57,6 115,2
TypType
Rzul[kN]
LT-32 Q8 Q0-40 180,9 180,9-45 160,9 160,9-50 173,3 173,9-55 157,6 158,3
TypType
Rzul[kN]
LT-32 K4 K5 K7 K9-25 165,3 195,6 195,6 195,6-32 131,2 156,6 173,9 173,9-40 103,3 123,3 161,7 180,9-45 91,9 109,6 143,7 160,9-50 82,7 98,7 129,3 166,7-55 75,2 89,7 117,6 151,5
05.05.15/
* Ma nicht gltig bei Verwendung vonAbhebesicherung, Sturmsicherung
*1 Spannweite Kran*2 Gewicht pro Kopftrgerpaar ohne
Anschlussplatten*3 Bei Schienenbreiten45, 55 etc.
Hinweise in Abs. 5.3 beachten
* Dimension not applicable when usinganti-jump catch or storm lock device
*1 Crane span*2 Weight per pair of endcarriages without
joint plates*3 For rail widths45, 55, etc. observe notes
in section 5.3
* Dimension pas valable en cas dutilisa-tion dun dispositif anti-soulvement ouune scurit-tempte
*1 Porte du pont roulant*2 Poids par paire de sommiers sans
plaques de fixation*3 Respectez les remarques dans la section
5.3 pour les largeurs de rail 45, 55, etc.
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
63/124
LS-T_
02.F
M
10.14 63
AbmessungenDimensionsDimensions
Kopftrger fr EintrgerlaufkraneEndcarriages for single girder o.h.t. cranes
Sommiers pour ponts roulants poss monopoutre
2
Buffer
Calculation see "Buffer selectiontable"page 46.
Joint plates
Travel drives
For more details, see Productinformation "Travel drives".
Butoirs
Pour le calcul, voir "Slection dubutoir", page 46.
Plaques de fixation
Groupes dentranement
Pour de plus amples informa-tions, voir Informations sur le
produit "Groupes dentranement".
B B
c1763v01
b2
Profil KastenProfile BoxProfil Caisson
Puffer
Auslegung siehe "Pufferauswahl-tabelle" Seite 46.
Anschlussplatten
Fahrantriebe
Nheres siehe Produktinforma-tion "Fahrantriebe".
Typ CodeType Code PufferBufferButoir
MaterialMaterialMatriau
d e max. Federwegmax. deflectionmax. crasement
Ezul GewindeThreadFilet
[mm] [mm] [mm] [Nm]B D2240 Gummi
RubberCaoutchouc
80 68 32 400 M12x35 0,6C D2241 100 85 42 1000 1,2D D2242 125 105 50 1600 2,3E 100x150 Polyurethan
PolyurethanePolyurthane
100 150 113 1200 0,8M 125x125 125 125 94 1550 1,1F 125x190 125 190 143 2320 1,4H 160x160 160 160 120 3300 2,6P 160x240 160 240 180 4950 3,5I 200x200 200 200 150 6400 4,5S 200x300 200 300 225 9600 6,2T 250x250 250 250 188 12500 M24x80 9,3
Y 250x375 250 375 281 18750 12,4
Q3 Q4 Q5 Q6 Q7 Q8 Q9 Q0p1 [mm] 520 520 630 630 850 850 1100 1100p2 [mm] 570 570 680 680 900 900 1150 1150p3 [mm] 380 480 380 480 380 480 380 480
Bmin-maxProfil/profile/profil [mm] 300-420 300-420 - - - - - -
Bmin-max Kasten/box/caisson [mm] 300-410 300-410 410-520 410-520 520-740 520-740 740-990 740-990b2maxseitlich/side/latrale [mm] 380 380 490 490 710 710 960 960
Gewicht pro Platte/weight per plate/poids par plaque [kg]
94 110 111 126 144 165 183 209
K4 K5 K7 K9p1 [mm] 520 630 850 1100p2 [mm] 570 680 900 1150p3 [mm] 350 350 350 350
Bmin-max[mm] 90-410 90-520 520-740 740-990
Gewicht pro Platte/weight per plate/poids par plaque [kg]
39 46 61 78
D GetriebeGear
Rducteur
MotorMotor
Moteur
m0 m1 m2
[mm] [mm]315 SDB4 4F18 567 369 182
4F38 629 202SDB5
*18/2F30 661 448 1548/2F318/2F42 7414F38 666 2024F48
c1686v01
e
d
M
c1679v01
p3
B
p1
p2
30
B
p1p2
c1679v02
p3
30
p3
p1
p2
c1679v03B
30
Q3, Q5, Q7, Q9
K4-K9
Q4, Q6, Q8, Q0
*1 SDB5Z (mit Zwischengetriebe)m0+100mm
*1 SDB5Z (with intermediate gear)m0+100mm
*1 SDB5Z (avec rducteur intermdiaire)m0+100mm
/05.05.15
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
64/124
LS-T_
02.F
M
64 10.14
Kopftrger fr EintrgerlaufkraneEndcarriages for single girder o.h.t. cranesSommiers pour ponts roulants poss monopoutre
AbmessungenDimensionsDimensions
"Calculation of required railwidth k"see page 45.
You will find the respective wheelloads on page 110.
"Calcul de la largeur de rail nces-saire k", voir page 45.
Vous trouvez les charges pargalet correspondantes page 110.
L1 b1[m] [mm]
L1 < 20 +020 < L1 < 30 +530 < L1 < 35 +10
L1 > 35 +15
"Ermittlung der erforderlichenSchienenbreite k"siehe Seite 45.
Die zugehrigen Radlasten findenSie auf Seite 110.
b1 55 60 65 70 75 80 85 90 95 100 105 110 115 120k*3
40 45 50 55(A55)
60 65(A65)
70 75(A75)
80 85 90 95 100(A100)
105
540
30
180
590 NmM20x140-10.9 ISO 4014
40
32
300 NmM16x90-10.9 ISO 4014
b1
k
22
400
c1576v08a
145 88
145 145
100
(SDB5)
20
320
350
10
215
25
max 35
300 NmM16x90-10.9 ISO 4014
"X" "Y" A - A
h1
h2
c1573v08
= =
k1
k0
e
m0
X
150
d
A
A
S6, S7, S9
K4, K5, K7, K9
m2
Y
16
min 300*
m1
min 380*
TypType
h1 h2
LT-40-25/32 548 48
LT-40-40 552 52
LT-40-45 668 168
LT-40-50/55 672 172
Anschluss seitlich/obenSide/top connectionFixation latrale/par le haut
Anschluss obenTop connectionFixation par le haut
LT-40
L1zul
*1
Typ
Type
k0 k1
[m] [mm] [mm] *218,5 LT-40-25 2500 3060 194023,5 LT-40-32 3150 3710 180030 LT-40-40 4000 4560 2160
33,5 LT-40-45 4500 5060 240037,5 LT-40-50 5000 5560 276041 LT-40-55 5500 6060 3100
Typ
Type
Rzul[kN]
LT-40 S6 S7 S9-25 304,3 304,3 304,3-32 268,8 304,3 304,3-40 211,7 304,3 304,3-45 188,1 288,0 288,0-50 169,3 259,2 259,2-55 153,9 235,6 235,6
TypType
Rzul[kN]
LT-40 K4 K5 K7 K9-25 165,3 197,3 258,7 304,3-32 131,2 156,6 205,3 264,6-40 103,3 123,3 161,7 208,3-45 91,9 109,6 143,7 185,2-50 82,7 98,7 129,3 166,7-55 75,2 89,7 117,6 151,5
05.05.15/
* Ma nicht gltig bei Verwendung vonAbhebesicherung, Sturmsicherung
*1 Spannweite Kran*2 Gewicht pro Kopftrgerpaar ohne
Anschlussplatten*3 Bei Schienenbreiten45, 55 etc.
Hinweise in Abs. 5.3 beachten
* Dimension not applicable when usinganti-jump catch or storm lock device
*1 Crane span*2 Weight per pair of endcarriages without
joint plates*3 For rail widths45, 55, etc. observe notes
in section 5.3
* Dimension pas valable en cas dutilisa-tion dun dispositif anti-soulvement ouune scurit-tempte
*1 Porte du pont roulant*2 Poids par paire de sommiers sans
plaques de fixation*3 Respectez les remarques dans la section
5.3 pour les largeurs de rail 45, 55, etc.
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
65/124
LS-T_
02.F
M
10.14 65
AbmessungenDimensionsDimensions
Kopftrger fr EintrgerlaufkraneEndcarriages for single girder o.h.t. cranes
Sommiers pour ponts roulants poss monopoutre
2
Buffer
Calculation see "Buffer selectiontable"page 46.
Joint plates
Travel drives
For more details, see Productinformation "Travel drives".
Butoirs
Pour le calcul, voir "Slection dubutoir", page 46.
Plaques de fixation
Groupes dentranement
Pour de plus amples informa-tions, voir Informations sur leproduit "Groupes dentranement".
B B
c1763v01
b2
Profil KastenProfile BoxProfil Caisson
Puffer
Auslegung siehe "Pufferauswahl-tabelle" Seite 46.
Anschlussplatten
Fahrantriebe
Nheres siehe Produktinforma-tion "Fahrantriebe".
Typ CodeType Code PufferBufferButoir
MaterialMaterialMatriau
d e max. Federwegmax. deflectionmax. crasement
Ezul GewindeThreadFilet
[mm] [mm] [mm] [Nm]B D2240 Gummi
RubberCaoutchouc
80 68 32 400 M12x35 0,6C D2241 100 85 42 1000 1,2D D2242 125 105 50 1600 2,3E 100x150 Polyurethan
PolyurethanePolyurthane
100 150 113 1200 0,8M 125x125 125 125 94 1550 1,1F 125x190 125 190 143 2320 1,4H 160x160 160 160 120 3300 2,6P 160x240 160 240 180 4950 3,5I 200x200 200 200 150 6400 4,5S 200x300 200 300 225 9600 6,2T 250x250 250 250 188 12500 M24x80 9,3
Y 250x375 250 375 281 18750 12,4
S6 S7 S9p1 [mm] 520 730 1100p2 [mm] 590 800 1170p3 [mm] 540 540 540
Bmin-max[mm] 410-520 550-740 750-1100
b2maxoben/top/par le haut [mm] 410 620 990b2maxseitlich/side/latrale [mm] 430 640 1010
Gewicht pro Platte/weight per plate/poids par plaque [kg]
126 172 252
K4 K5 K7 K9p1 [mm] 520 630 850 1100p2 [mm] 570 680 900 1150p3 [mm] 350 350 350 350
Bmin-max[mm] 90-410 90-520 520-740 740-990
Gewicht pro Platte/weight per plate/poids par plaque [kg]
39 46 61 78
D GetriebeGear
Rducteur
MotorMotor
Moteur
m0 m1 m2
[mm] [mm]400 SDB5
*18/2F30 671 490 1548/2F318/2F42 7514F38 676 2024F48
c1686v01
e
d
M
B
p1
p2
c1717v01
p3
5
S6-S9
p3
p1
p2
c1679v03
B
30
K4-K9
*1 SDB5Z (mit Zwischengetriebe)m0+100mm
*1 SDB5Z (with intermediate gear)m0+100mm
*1 SDB5Z (avec rducteur intermdiaire)m0+100mm
/05.05.15
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
66/124
LS-T_
03.F
M
66 10.14
Kopftrger fr ZweitrgerlaufkraneEndcarriages for double girder o.h.t. cranesSommiers pour ponts roulants poss bipoutre
AbmessungenDimensionsDimensions
"Calculation of required railwidth k"see page 45.
You will find the respective wheelloads on page 101.
"Calcul de la largeur de rail nces-saire k", voir page 45.
Vous trouvez les charges pargalet correspondantes page 101.
"Ermittlung der erforderlichenSchienenbreite k"siehe Seite 45.
Die zugehrigen Radlasten findenSie auf Seite 101.
c1669v09
k1
k0
m0
e
100
d
A
A
a
Y
A3
8
m2
min 205*
m1
b1 50 55 60 65 70k*3
40 45(A45)
50 55(A55)
60
TypType
a max.[mm]
A3LE-09-16 470LE-09-20 870
140
15
0
300 NmM16x60-10.9ISO 4014
82,5
33
"Y" A - A
b1
k
80
10
15
901
30
83 83
c1576v15
60
24
Anschluss obenTop connectionFixation par le haut
LE-09
L1zul
*1
Typ
Type
k0 k1
[m] [mm] [mm] *212 LE-09-16 1600 1956 13815 LE-09-20 2000 2356 154
TypType
Rzul[kN] *4
A3LE-09-16 24,3LE-09-20 24,3
05.05.15/
* Ma nicht gltig bei Verwendung vonAbhebesicherung, Sturmsicherung
*1 Spannweite Kran*2 Gewicht pro Kopftrgerpaar ohne
Anschlussplatten*3 Bei Schienenbreiten45, 55 etc.
Hinweise in Abs. 5.3 beachten*4 Rzulbei Spurmittenma Katze (Spw)
> 1250 mm
* Dimension not applicable when usinganti-jump catch or storm lock device
*1 Crane span*2 Weight per pair of endcarriages without
joint plates*3 For rail widths45, 55, etc. observe notes
in section 5.3*4 Rzulwith crab track gauge (Spw)
> 1250mm
* Dimension pas valable en cas dutilisa-tion dun dispositif anti-soulvement ouune scurit-tempte
*1 Porte du pont roulant*2 Poids par paire de sommiers sans
plaques de fixation*3 Respectez les remarques dans la section
5.3 pour les largeurs de rail 45, 55, etc.*4 Rzulavec cartement du chariot (Spw)
> 1250mm
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
67/124
LS-T_
03.F
M
10.14 67
AbmessungenDimensionsDimensions
Kopftrger fr ZweitrgerlaufkraneEndcarriages for double girder o.h.t. cranes
Sommiers pour ponts roulants poss bipoutre
2
Buffer
Calculation see "Buffer selectiontable"page 46.
Joint plates
Travel drives
For more details, see Productinformation "Travel drives".
Butoirs
Pour le calcul, voir "Slection dubutoir", page 46.
Plaques de fixation
Groupes dentranement
Pour de plus amples informa-tions, voir Informations sur leproduit "Groupes dentranement".
B B
c1762v01
Profil KastenProfile BoxProfil Caisson
Puffer
Auslegung siehe "Pufferauswahl-tabelle" Seite 46.
Anschlussplatten
Fahrantriebe
Nheres siehe Produktinforma-tion "Fahrantriebe".
Typ CodeType Code PufferBufferButoir
MaterialMaterialMatriau
d e max. Federwegmax. deflectionmax. crasement
Ezul GewindeThreadFilet
[mm] [mm] [mm] [Nm]A D1801 Gummi
RubberCaoutchouc
63 53 30 250 M12x35 0,3B D2240 80 68 32 400 0,6C D2241 100 85 42 1000 1,2K 80x80 Polyurethan
PolyurethanePolyurthane
80 80 60 400 0,4G 100x100 100 100 75 800 0,6E 100x150 100 150 113 1200 0,8
A3
p1 [mm] 360p2 [mm] 410p3 [mm] 140
Bmin-max[mm] 90-310
Gewicht pro Platte/weight per plate/poids par plaque [kg]
7
D GetriebeGear
Rducteur
MotorMotor
Moteur
m0 m1 m2
[mm] [mm]90 SDB3 8/2F12 505 225 134
8/2F134F18 182
c1686v01
e
d
M
p3
c1674v02B
p1
p2A3
/05.05.15
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
68/124
LS-T_
03.F
M
68 10.14
Kopftrger fr ZweitrgerlaufkraneEndcarriages for double girder o.h.t. cranesSommiers pour ponts roulants poss bipoutre
AbmessungenDimensionsDimensions
"Calculation of required railwidth k"see page 45.
You will find the respective wheelloads on page 101.
"Calcul de la largeur de rail nces-saire k", voir page 45.
Vous trouvez les charges pargalet correspondantes page 101.
"Ermittlung der erforderlichenSchienenbreite k"siehe Seite 45.
Die zugehrigen Radlasten findenSie auf Seite 101.
140
15
0
300 NmM16x60-10.9ISO 4014
82,5
33
200
2010
84
590 Nm
M20x70-10.9 ISO 4014
"X" "Y" A - A
b1
k
80
10
15
90
210
83 83
c1576v01
60
24
c1669v01
k1
k0
X
a
m0
e
100
d
A
A
a
Y
A3
8
m2
400x200
min 205*
min 280*
m1
b1 50 55 60 65 70k*3
40 45(A45)
50 55(A55)
60
TypType
a max. [mm]400x200 A3
L.-09-16 270 470L.-09-20 670 870L.-09-25 1170 1370
Anschluss seitlichSide connectionFixation latrale
Anschluss obenTop connectionFixation par le haut
LS/LT-09
L1zul
*1
Typ
Type
k0 k1
[m] [mm] [mm] *212 LS-09-16 1600 1876 17015 LS-09-20 2000 2276 198
18,5 LS-09-25 2500 2776 23612 LT-09-16 1600 1876 17015 LT-09-20 2000 2276 198
18,5 LT-09-25 2500 2776 236
Typ
Type
Rzul[kN] *4
400x200LS-09-16 24,3LS-09-20 24,3LS-09-25 24,3
TypType
Rzul[kN] *4
A3LT-09-16 24,3LT-09-20 24,3LT-09-25 24,3
05.05.15/
* Ma nicht gltig bei Verwendung vonAbhebesicherung, Sturmsicherung
*1 Spannweite Kran*2 Gewicht pro Kopftrgerpaar ohne
Anschlussplatten*3 Bei Schienenbreiten45, 55 etc.
Hinweise in Abs. 5.3 beachten*4 Rzulbei Spurmittenma Katze (Spw)
> 1250 mm
* Dimension not applicable when usinganti-jump catch or storm lock device
*1 Crane span*2 Weight per pair of endcarriages without
joint plates*3 For rail widths45, 55, etc. observe notes
in section 5.3*4 Rzulwith crab track gauge (Spw)
> 1250mm
* Dimension pas valable en cas dutilisa-tion dun dispositif anti-soulvement ouune scurit-tempte
*1 Porte du pont roulant*2 Poids par paire de sommiers sans
plaques de fixation*3 Respectez les remarques dans la section
5.3 pour les largeurs de rail 45, 55, etc.*4 Rzulavec cartement du chariot (Spw)
> 1250mm
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
69/124
LS-T_
03.F
M
10.14 69
AbmessungenDimensionsDimensions
Kopftrger fr ZweitrgerlaufkraneEndcarriages for double girder o.h.t. cranes
Sommiers pour ponts roulants poss bipoutre
2
Buffer
Calculation see "Buffer selectiontable"page 46.
Joint plates
Travel drives
For more details, see Productinformation "Travel drives".
Butoirs
Pour le calcul, voir "Slection dubutoir", page 46.
Plaques de fixation
Groupes dentranement
Pour de plus amples informa-tions, voir Informations sur le
produit "Groupes dentranement".
B B
c1763v01
b2
Profil KastenProfile BoxProfil Caisson
Puffer
Auslegung siehe "Pufferauswahl-tabelle" Seite 46.
Anschlussplatten
Fahrantriebe
Nheres siehe Produktinforma-tion "Fahrantriebe".
Typ CodeType Code PufferBufferButoir
MaterialMaterialMatriau
d e max. Federwegmax. deflectionmax. crasement
Ezul GewindeThreadFilet
[mm] [mm] [mm] [Nm]A D1801 Gummi
RubberCaoutchouc
63 53 30 250 M12x35 0,3B D2240 80 68 32 400 0,6C D2241 100 85 42 1000 1,2K 80x80 Polyurethan
PolyurethanePolyurthane
80 80 60 400 0,4G 100x100 100 100 75 800 0,6E 100x150 100 150 113 1200 0,8
400x200
p1 [mm] 400p2 [mm] 490p3 [mm] 200
Bmin-max[mm] 146-400
b2max[mm] 320
Gewicht pro Platte/weight per plate/poids par plaque [kg]
17
A3p1 [mm] 360p2 [mm] 410p3 [mm] 140
Bmin-max[mm] 90-310
Gewicht pro Platte/weight per plate/poids par plaque [kg] 7
D GetriebeGear
Rducteur
MotorMotor
Moteur
m0 m1 m2
[mm] [mm]90 SDB3 8/2F12 505 225 134
8/2F134F18 182
c1686v01
e
d
M
c1674v01
p3
B
p1
p2400x200
p3
c1674v02B
p1
p2A3
/05.05.15
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
70/124
LS-T_
03.F
M
70 10.14
Kopftrger fr ZweitrgerlaufkraneEndcarriages for double girder o.h.t. cranesSommiers pour ponts roulants poss bipoutre
AbmessungenDimensionsDimensions
"Calculation of required railwidth k"see page 45.
You will find the respective wheelloads on page 102.
"Calcul de la largeur de rail nces-saire k", voir page 45.
Vous trouvez les charges pargalet correspondantes page 102.
"Ermittlung der erforderlichenSchienenbreite k"siehe Seite 45.
Die zugehrigen Radlasten findenSie auf Seite 102.
170
15
0
300 NmM16x60-10.9ISO 4014
95
34
"X" "Y" A - A
255
2513
103
590 Nm
M20x80-10.9 ISO 4014
b1
k
97
15
18
110
265
98 98
c1576v02
60
32
c1669v02
k1
k0
X
a
m0
e
100
d
A
A
a
Y
A4, A6
8
min 280*
400x255
min 205*
m2
m1
b1 52 57 62 67 72 77 82 87k*3
40 45(A45)
50 55(A55)
60 65(A65)
70 75(A75)
L1 b1[m] [mm]
L1 < 20 +020 < L1 < 30 +5
TypType
a max. [mm]400x255 A4 A6
L.-11-16 270 370 -L.-11-20 670 770 390L.-11-25 1170 1270 890L.-11-32 1820 1920 1540
Anschluss seitlichSide connectionFixation latrale
Anschluss obenTop connectionFixation par le haut
LS/LT-11
L1zul
*1
Typ
Type
k0 k1
[m] [mm] [mm] *212 LS-11-16 1600 1876 25815 LS-11-20 2000 2276 304
18,5 LS-11-25 2500 2776 36023,5 LS-11-32 3150 3426 43412 LT-11-16 1600 1876 21615 LT-11-20 2000 2276 254
18,5 LT-11-25 2500 2776 30023,5 LT-11-32 3150 3426 360
TypType
Rzul[kN] *4
400x255LS-11-16 40,0LS-11-20 40,0LS-11-25 40,0LS-11-32 40,0
TypType
Rzul[kN] *4
A4 A6LT-11-16 40,0 -LT-11-20 40,0 40,0LT-11-25 40,0 40,0LT-11-32 40,0 40,0
05.05.15/
* Ma nicht gltig bei Verwendung vonAbhebesicherung, Sturmsicherung
*1 Spannweite Kran*2 Gewicht pro Kopftrgerpaar ohne
Anschlussplatten*3 Bei Schienenbreiten45, 55 etc.
Hinweise in Abs. 5.3 beachten*4 Rzulbei Spurmittenma Katze (Spw)
> 1250 mm
* Dimension not applicable when usinganti-jump catch or storm lock device
*1 Crane span*2 Weight per pair of endcarriages without
joint plates*3 For rail widths45, 55, etc. observe notes
in section 5.3*4 Rzulwith crab track gauge (Spw)
> 1250mm
* Dimension pas valable en cas dutilisa-tion dun dispositif anti-soulvement ouune scurit-tempte
*1 Porte du pont roulant*2 Poids par paire de sommiers sans
plaques de fixation*3 Respectez les remarques dans la section
5.3 pour les largeurs de rail 45, 55, etc.*4 Rzulavec cartement du chariot (Spw)
> 1250mm
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
71/124
LS-T_
03.F
M
10.14 71
AbmessungenDimensionsDimensions
Kopftrger fr ZweitrgerlaufkraneEndcarriages for double girder o.h.t. cranes
Sommiers pour ponts roulants poss bipoutre
2
Buffer
Calculation see "Buffer selectiontable"page 46.
Joint plates
Travel drives
For more details, see Productinformation "Travel drives".
Puffer
Auslegung siehe "Pufferauswahl-tabelle" Seite 46.
Anschlussplatten
Fahrantriebe
Nheres siehe Produktinforma-tion "Fahrantriebe".
Typ CodeType Code PufferBufferButoir
MaterialMaterialMatriau
d e max. Federwegmax. deflectionmax. crasement
Ezul GewindeThreadFilet
[mm] [mm] [mm] [Nm]A D1801 Gummi
RubberCaoutchouc
63 53 30 250 M12x35 0,3B D2240 80 68 32 400 0,6C D2241 100 85 42 1000 1,2K 80x80 Polyurethan
PolyurethanePolyurthane
80 80 60 400 0,4G 100x100 100 100 75 800 0,6E 100x150 100 150 113 1200 0,8
400x255
p1 [mm] 400p2 [mm] 490p3 [mm] 255
Bmin-max[mm] 146-400
b2max[mm] 320
Gewicht pro Platte/weight per plate/poids par plaque [kg]
24
A4 A6p1 [mm] 410 600p2 [mm] 460 650p3 [mm] 170 170
Bmin-max[mm] 90-350 300-550
Gewicht pro Platte/weight per plate/poids par plaque [kg] 9 13
D GetriebeGear
Rducteur
MotorMotor
Moteur
m0 m1 m2
[mm] [mm]110 SDB3 8/2F12 519 235 134
8/2F134F18 182
c1686v01
e
d
M
p3
B c1675v01
p1
p2400x255
p3
c1675v02B
p1
p2A4, A6
Butoirs
Pour le calcul, voir "Slection dubutoir", page 46.
Plaques de fixation
Groupes dentranement
Pour de plus amples informa-tions, voir Informations sur le
produit "Groupes dentranement".
B B
c1763v01
b2
Profil KastenProfile BoxProfil Caisson
/05.05.15
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
72/124
LS-T_
03.F
M
72 10.14
Kopftrger fr ZweitrgerlaufkraneEndcarriages for double girder o.h.t. cranesSommiers pour ponts roulants poss bipoutre
AbmessungenDimensionsDimensions
"Calculation of required railwidth k"see page 45.
You will find the respective wheelloads on page 103.
"Calcul de la largeur de rail nces-saire k", voir page 45.
Vous trouvez les charges pargalet correspondantes page 103.
"Ermittlung der erforderlichenSchienenbreite k"siehe Seite 45.
Die zugehrigen Radlasten findenSie auf Seite 103.
170
15
0
300 NmM16x60-10.9ISO 4014
95
34
"X" "Y" A - A
255
2513
103
590 Nm
M20x80-10.9 ISO 4014
6075
(SDB3)
(SDB4)
b1
k
100
15
140
265
98 98
c1576v07
31
18
c1669v07
k1
k0
X
a
m0
e
100
d
A
A
a
Y
A4, A6
12
min 280*
400x255
min 205*
m2
m1
b1 54 59 64 69 74 79 84k*3
40 45(A45)
50 55(A55)
60 65(A65)
70L1 b1[m] [mm]
L1 < 20 +020 < L1 < 30 +530 < L1 < 35 +10
TypType
a max. [mm]400x255 A4 A6
L.-14-16 270 370 -L.-14-20 670 770 390L.-14-25 1170 1270 890L.-14-32 1820 1920 1540L.-14-35 2170 2270 1890L.-14-40 2670 2770 2390
Anschluss seitlichSide connectionFixation latrale
Anschluss obenTop connectionFixation par le haut
LS/LT-14
L1zul
*1
Typ
Type
k0 k1
[m] [mm] [mm] *212 LS-14-16 1600 1884 28215 LS-14-20 2000 2284 328
18,5 LS-14-25 2500 2784 38423,5 LS-14-32 3150 3434 45826 LS-14-35 3500 3784 49830 LS-14-40 4000 4284 55812 LT-14-16 1600 1884 24415 LT-14-20 2000 2284 282
18,5 LT-14-25 2500 2784 32823,5 LT-14-32 3150 3434 38826 LT-14-35 3500 3784 42230 LT-14-40 4000 4284 468
TypType
Rzul[kN] *4
400x255LS-14-16 47,8LS-14-20 47,8LS-14-25 47,8LS-14-32 47,8LS-14-35 47,8LS-14-40 bei/for/pour Spw [mm]
1250 32,51400 33,4
1800 36,72240 42,12500 46,6
>2800 47,8
TypType
Rzul[kN] *4
A4 A6LT-14-16 47,8 -LT-14-20 47,8 47,8LT-14-25 47,8 47,8
LT-14-32 47,8 47,8LT-14-35 47,8 47,8LT-14-40 bei/for/pour Spw [mm]
1250 32,5 32,51400 33,4 33,41800 36,7 36,72240 42,1 42,12500 46,6 46,6
>2800 47,8 47,8
05.05.15/
* Ma nicht gltig bei Verwendung vonAbhebesicherung, Sturmsicherung
*1 Spannweite Kran*2 Gewicht pro Kopftrgerpaar ohne
Anschlussplatten*3 Bei Schienenbreiten45, 55 etc.
Hinweise in Abs. 5.3 beachten*4 Rzulbei Spurmittenma Katze (Spw)
> 1250 mm
* Dimension not applicable when usinganti-jump catch or storm lock device
*1 Crane span*2 Weight per pair of endcarriages without
joint plates*3 For rail widths45, 55, etc. observe notes
in section 5.3*4 Rzulwith crab track gauge (Spw)
> 1250mm
* Dimension pas valable en cas dutilisa-tion dun dispositif anti-soulvement ouune scurit-tempte
*1 Porte du pont roulant*2 Poids par paire de sommiers sans
plaques de fixation*3 Respectez les remarques dans la section
5.3 pour les largeurs de rail 45, 55, etc.*4 Rzulavec cartement du chariot (Spw)
> 1250mm
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
73/124
LS-T_
03.F
M
10.14 73
AbmessungenDimensionsDimensions
Kopftrger fr ZweitrgerlaufkraneEndcarriages for double girder o.h.t. cranes
Sommiers pour ponts roulants poss bipoutre
2
Buffer
Calculation see "Buffer selectiontable"page 46.
Joint plates
Travel drives
For more details, see Productinformation "Travel drives".
Butoirs
Pour le calcul, voir "Slection dubutoir", page 46.
Plaques de fixation
Groupes dentranement
Pour de plus amples informa-tions, voir Informations sur leproduit "Groupes dentranement".
B B
c1763v01
b2
Profil KastenProfile BoxProfil Caisson
Puffer
Auslegung siehe "Pufferauswahl-tabelle" Seite 46.
Anschlussplatten
Fahrantriebe
Nheres siehe Produktinforma-tion "Fahrantriebe".
Typ CodeType Code PufferBufferButoir
MaterialMaterialMatriau
d e max. Federwegmax. deflectionmax. crasement
Ezul GewindeThreadFilet
[mm] [mm] [mm] [Nm]A D1801 Gummi
RubberCaoutchouc
63 53 30 250 M12x35 0,3B D2240 80 68 32 400 0,6C D2241 100 85 42 1000 1,2K 80x80 Polyurethan
PolyurethanePolyurthane
80 80 60 400 0,4G 100x100 100 100 75 800 0,6E 100x150 100 150 113 1200 0,8M 125x125 125 125 94 1550 1,1F 125x190 125 190 143 2320 1,4H 160x160 160 160 120 3300 2,6P 160x240 160 240 180 4950 3,5
400x255p1 [mm] 400p2 [mm] 490p3 [mm] 255
Bmin-max[mm] 146-400
b2max[mm] 320
Gewicht pro Platte/weight per plate/poids par plaque [kg]
24
A4 A6p1 [mm] 410 600p2 [mm] 460 650p3 [mm] 170 170
Bmin-max[mm] 90-350 300-550
Gewicht pro Platte/weight per plate/poids par plaque [kg]
9 13
D GetriebeGear
Rducteur
MotorMotor
Moteur
m0 m1 m2
[mm] [mm]140 SDB3 8/2F12 519 249 134
8/2F13
4F18 182
c1686v01
e
d
M
p3
B c1675v01
p1
p2400x255
p3
c1675v02B
p1
p2A4, A6
/05.05.15
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
74/124
LS-T_
03.F
M
74 10.14
Kopftrger fr ZweitrgerlaufkraneEndcarriages for double girder o.h.t. cranesSommiers pour ponts roulants poss bipoutre
AbmessungenDimensionsDimensions
"Calculation of required railwidth k"see page 45.
You will find the respective wheelloads on page 104.
"Calcul de la largeur de rail nces-saire k", voir page 45.
Vous trouvez les charges pargalet correspondantes page 104.
"Ermittlung der erforderlichenSchienenbreite k"siehe Seite 45.
Die zugehrigen Radlasten findenSie auf Seite 104.
255
20
0
300 NmM16x70-10.9ISO 4014
180
36
"X" "Y" A - A
255/305
2513
104
590 Nm
M20x80-10.9 ISO 4014
6075
(SDB3)
(SDB4)
b1
k
100
15
160
98 101
c1576v09a
31
18
h1
c1669v03
k1
k0
m0
e
100
d
A
A
a
Y
B4, B6
min 310*
450x305
min 235*
m2
X
a
350x255
12
m1
b1 54 59 64 69 74 79 84k*3
40 45(A45)
50 55(A55)
60 65(A65)
70L1 b1[m] [mm]
L1 < 20 +020 < L1 < 30 +530 < L1 < 35 +10
TypType
a max. [mm]350x255 450x305 B4 B6
L.-16-16 300 - 130 -L.-16-20 700 - 530 130L.-16-25 1200 - 1030 630L.-16-32 1850 - 1680 1280L.-16-40 - 2380 2530 2130L.-16-45 - 2880 3030 2630
TypType
h1
LS LT
16-16/20/25/32 268 265
16-40/45 318 315
Anschluss seitlichSide connectionFixation latrale
Anschluss obenTop connectionFixation par le haut
LS/LT-16
L1zul
*1
Typ
Type
k0 k1
[m] [mm] [mm] *212 LS-16-16 1600 1924 39415 LS-16-20 2000 2324 440
18,5 LS-16-25 2500 2824 49623,5 LS-16-32 3150 3474 56830 LS-16-40 4000 4324 736
33,5 LS-16-45 4500 4824 80012 LT-16-16 1600 1924 39415 LT-16-20 2000 2324 440
18,5 LT-16-25 2500 2824 49623,5 LT-16-32 3150 3474 56830 LT-16-40 4000 4324 736
33,5 LT-16-45 4500 4824 800
TypType
Rzul[kN] *4
350x255 450x305LS-16-16 60,0 -LS-16-20 60,0 -LS-16-25 60,0 -LS-16-32 60,0 -LS-16-40 - 54,8LS-16-45 bei/for/pour Spw [mm]
1250 - 41,71400 - 43,3
1800 - 47,62240 - 54,6
>2500 - 60,0
TypType
Rzul[kN] *4
B4 B6LT-16-16 60,0 -LT-16-20 60,0 60,0LT-16-25 60,0 60,0LT-16-32 60,0 60,0
LT-16-40 60,0 60,0LT-16-45 bei/for/pour Spw [mm]1250 41,7 41,71400 43,3 43,31800 47,6 47,62240 54,6 54,6
>2500 60,0 60,0
05.05.15/
* Ma nicht gltig bei Verwendung vonAbhebesicherung, Sturmsicherung
*1 Spannweite Kran*2 Gewicht pro Kopftrgerpaar ohne
Anschlussplatten*3 Bei Schienenbreiten45, 55 etc.
Hinweise in Abs. 5.3 beachten*4 Rzulbei Spurmittenma Katze (Spw)
> 1250 mm
* Dimension not applicable when usinganti-jump catch or storm lock device
*1 Crane span*2 Weight per pair of endcarriages without
joint plates*3 For rail widths45, 55, etc. observe notes
in section 5.3*4 Rzulwith crab track gauge (Spw)
> 1250mm
* Dimension pas valable en cas dutilisa-tion dun dispositif anti-soulvement ouune scurit-tempte
*1 Porte du pont roulant*2 Poids par paire de sommiers sans
plaques de fixation*3 Respectez les remarques dans la section
5.3 pour les largeurs de rail 45, 55, etc.*4 Rzulavec cartement du chariot (Spw)
> 1250mm
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
75/124
LS-T_
03.F
M
10.14 75
AbmessungenDimensionsDimensions
Kopftrger fr ZweitrgerlaufkraneEndcarriages for double girder o.h.t. cranes
Sommiers pour ponts roulants poss bipoutre
2
Buffer
Calculation see "Buffer selectiontable"page 46.
Joint plates
Travel drives
For more details, see Productinformation "Travel drives".
Butoirs
Pour le calcul, voir "Slection dubutoir", page 46.
Plaques de fixation
Groupes dentranement
Pour de plus amples informa-tions, voir Informations sur leproduit "Groupes dentranement".
B B
c1763v01
b2
Profil KastenProfile BoxProfil Caisson
Puffer
Auslegung siehe "Pufferauswahl-tabelle" Seite 46.
Anschlussplatten
Fahrantriebe
Nheres siehe Produktinforma-tion "Fahrantriebe".
Typ CodeType Code PufferBufferButoir
MaterialMaterialMatriau
d e max. Federwegmax. deflectionmax. crasement
Ezul GewindeThreadFilet
[mm] [mm] [mm] [Nm]B D2240 Gummi
RubberCaoutchouc
80 68 32 400 M12x35 0,6C D2241 100 85 42 1000 1,2D D2242 125 105 50 1600 2,3K 80x80 Polyurethan
PolyurethanePolyurthane
80 80 60 400 0,4G 100x100 100 100 75 800 0,6E 100x150 100 150 113 1200 0,8M 125x125 125 125 94 1550 1,1F 125x190 125 190 143 2320 1,4H 160x160 160 160 120 3300 2,6P 160x240 160 240 180 4950 3,5
350x255 450x305p1 [mm] 350 450p2 [mm] 430 650p3 [mm] 255 305
Bmin-max[mm] 146-370 300-470
b2max[mm] 270 370
Gewicht pro Platte/weight per plate/poids par plaque [kg]
23 38
B4 B6p1 [mm] 500 700p2 [mm] 550 750p3 [mm] 255 255
Bmin-max[mm] 200-350 350-550
Gewicht pro Platte/weight per plate/poids par plaque [kg]
21 29
D GetriebeGear
Rducteur
MotorMotor
Moteur
m0 m1 m2
[mm] [mm]160 SDB3 4F18 522 259 182
SDB4 8/2F12 533 291 1348/2F138/2F30 590 1548/2F314F18 533 1824F38 595 202
c1686v01
e
d
M
c1676v01
p3
B
p1
p2
c1676v02
p3
B
p1
p2
60
c1676v03
p3
p1
p2
B
48
350x255
450x305
B4, B6
/05.05.15
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
76/124
LS-T_
03.F
M
76 10.14
Kopftrger fr ZweitrgerlaufkraneEndcarriages for double girder o.h.t. cranesSommiers pour ponts roulants poss bipoutre
AbmessungenDimensionsDimensions
"Calculation of required railwidth k"see page 45.
You will find the respective wheelloads on page 105.
"Calcul de la largeur de rail nces-saire k", voir page 45.
Vous trouvez les charges pargalet correspondantes page 105.
"Ermittlung der erforderlichenSchienenbreite k"siehe Seite 45.
Die zugehrigen Radlasten findenSie auf Seite 105.
c1669v04
k1
k0
m0
e
150
d
A
A
a
Y
L3-L6
min 290*
R3-R6
min 225*
m2
X
a
12
m1
b1 54 59 64 69 74 79 84 89 94k*3
40 45(A45)
50 55(A55)
60 65(A65)
70 75(A75)
80L1 b1[m] [mm]
L1 < 20 +020 < L1 < 30 +530 < L1 < 35 +10
TypType a max. [mm]R3 R4 R5 R6 L3 L4 L5 L6LT-20-16 520 300 80 - 330 110 - -LT-20-20 920 700 480 260 730 510 290 70LT-20-25 1420 1200 980 760 1230 1010 790 570LT-20-32 2070 1850 1630 1410 1880 1660 1440 1220LT-20-40 2920 2700 2480 2260 2730 2510 2290 2070
280
L3: 25L4-L6: 20
0
300 NmM16x70-10.9 ISO 4014
180
31/36
"X" "Y" A - A
325
2015
122
25
300 NmM16x70-10.9 ISO 4014
590 NmM20x90-10.9 ISO 4014
31
6075
(SD
B3)
(SD
B4)
b1
k
110
15
200
315
122 122
c1576v04
45
20
Anschluss seitlich/obenSide/top connectionFixation latrale/par le haut
Anschluss obenTop connectionFixation par le haut
LT-20
L1zul
*1
Typ
Type
k0 k1
[m] [mm] [mm] *212 LT-20-16 1600 1920 39815 LT-20-20 2000 2320 454
18,5 LT-20-25 2500 2820 53023,5 LT-20-32 3150 3470 62230 LT-20-40 4000 4320 744
33,5 LT-20-45 4500 4820 818
Typ
Type
Rzul[kN] *4
R3 R3 R4 R5 R6
LT-20
-16 104,3 104,3 104,3 104,3 --20 104,3 104,3 104,3 104,3 104,3-25 96,0 104,3 104,3 104,3 104,3-32 76,2 104,3 104,3 104,3 104,3-40 bei/for/pour Spw [mm]
1250 60,0 73,9 73,9 73,9 73,91400 60,0 77,5 77,5 77,5 77,51800 60,0 87,5 87,5 87,5 87,5
>2240 60,0 104,3 104,3 104,3 104,3-45 bei/for/pour Spw [mm]
1250 51,3 51,3 51,3 51,3 51,31400 53,2 53,2 53,2 53,2 53,2
1800 53,3 58,5 58,5 58,5 58,52240 53,3 67,1 67,1 67,1 67,12500 53,3 744 74,4 74,4 74,42800 53,3 85,8 85,8 85,8 85,83150 53,3 99,6 104,3 104,3 104,3
TypType
Rzul[kN] *4
LT-20 L3 L4 L5 L6-16 104,3 104,3 - --20 104,3 104,3 104,3 104,3-25 104,3 104,3 104,3 104,3-32 104,3 104,3 104,3 104,3-40 bei/for/pour Spw [mm]
1250 73,9 73,9 73,9 73,91400 77,5 77,5 77,5 77,51800 87,5 87,5 87,5 87,5
>2240 104,3 104,3 104,3 104,3-45 bei/for/pour Spw [mm]
1250 51,3 51,3 51,3 51,31400 53,2 53,2 53,2 53,21800 58,5 58,5 58,5 58,52240 67,1 67,1 67,1 67,12500 74,4 74,4 74,4 74,42800 85,8 85,8 85,8 85,8
3150 94,8 104,3 104,3 104,3
05.05.15/
* Ma nicht gltig bei Verwendung vonAbhebesicherung, Sturmsicherung
*1 Spannweite Kran*2 Gewicht pro Kopftrgerpaar ohne
Anschlussplatten*3 Bei Schienenbreiten45, 55 etc.
Hinweise in Abs. 5.3 beachten*4 Rzulbei Spurmittenma Katze (Spw)
> 1250 mm
* Dimension not applicable when usinganti-jump catch or storm lock device
*1 Crane span*2 Weight per pair of endcarriages without
joint plates*3 For rail widths45, 55, etc. observe notes
in section 5.3*4 Rzulwith crab track gauge (Spw)
> 1250mm
* Dimension pas valable en cas dutilisa-tion dun dispositif anti-soulvement ouune scurit-tempte
*1 Porte du pont roulant*2 Poids par paire de sommiers sans
plaques de fixation*3 Respectez les remarques dans la section
5.3 pour les largeurs de rail 45, 55, etc.*4 Rzulavec cartement du chariot (Spw)
> 1250mm
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
77/124
LS-T_
03.F
M
10.14 77
AbmessungenDimensionsDimensions
Kopftrger fr ZweitrgerlaufkraneEndcarriages for double girder o.h.t. cranes
Sommiers pour ponts roulants poss bipoutre
2
Buffer
Calculation see "Buffer selectiontable"page 46.
Joint plates
Travel drives
For more details, see Productinformation "Travel drives".
Butoirs
Pour le calcul, voir "Slection dubutoir", page 46.
Plaques de fixation
Groupes dentranement
Pour de plus amples informa-tions, voir Informations sur leproduit "Groupes dentranement".
B B
c1763v01
b2
Profil KastenProfile BoxProfil Caisson
Puffer
Auslegung siehe "Pufferauswahl-tabelle" Seite 46.
Anschlussplatten
Fahrantriebe
Nheres siehe Produktinforma-tion "Fahrantriebe".
Typ CodeType Code PufferBufferButoir
MaterialMaterialMatriau
d e max. Federwegmax. deflectionmax. crasement
Ezul GewindeThreadFilet
[mm] [mm] [mm] [Nm]B D2240 Gummi
RubberCaoutchouc
80 68 32 400 M12x35 0,6C D2241 100 85 42 1000 1,2D D2242 125 105 50 1600 2,3G 100x100 Polyurethan
PolyurethanePolyurthane
100 100 75 800 0,6E 100x150 100 150 113 1200 0,8M 125x125 125 125 94 1550 1,1F 125x190 125 190 143 2320 1,4H 160x160 160 160 120 3300 2,6P 160x240 160 240 180 4950 3,5I 200x200 200 200 150 6400 4,5S 200x300 200 300 225 9600 6,2
R3 R4 R5 R6p1 [mm] 250 360 470 580p2 [mm] 300 410 520 630p3 [mm] 325 325 325 325
Bmin-maxProfil/profile/profil [mm] 230-300 300-410 - -
Bmin-maxKasten/box/caisson Var 1 [mm] 230-300 300-410 410-520 520-630
b2maxVar 1 [mm] 196 306 416 528Bmin-maxKasten/box/caisson Var 2 [mm] - 300-320 321-430 431-540
b2maxVar 2 [mm] - 250 360 470
Gewicht pro Platte/weight per plate/
poids par plaque [kg]
33 43 53 63
L3 L4 L5 L6p1 [mm] 410 520 630 740p2 [mm] 460 570 680 790p3 [mm] 280 280 280 280
Bmin-max[mm] 240-300 300-410 410-520 520-630
Gewicht pro Platte/weight per plate/poids par plaque [kg]
24 25 29 34
D GetriebeGear
Rducteur
MotorMotor
Moteur
m0 m1 m2
[mm] [mm]200 SDB3 4F18 543 270 182
SDB4 8/2F12 554 301 1348/2F138/2F30 611 1548/2F314F18 554 1824F38 616 202
c1686v01
e
d
M
p3
c1677v01BVar1
BVar2
p1
p2
13
Var 2
Var 1
R3-R6
p1
p2
p3
c1677v02
B30
L3-L6
/05.05.15
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
78/124
LS-T_
03.F
M
78 10.14
Kopftrger fr ZweitrgerlaufkraneEndcarriages for double girder o.h.t. cranesSommiers pour ponts roulants poss bipoutre
AbmessungenDimensionsDimensions
"Calculation of required railwidth k"see page 45.
You will find the respective wheelloads on page 106.
"Calcul de la largeur de rail nces-saire k", voir page 45.
Vous trouvez les charges pargalet correspondantes page 106.
"Ermittlung der erforderlichenSchienenbreite k"siehe Seite 45.
Die zugehrigen Radlasten findenSie auf Seite 106.
280
25
0
300 NmM16x70-10.9 ISO 4014
180
29
320
3035/
135(h1>31
5mm)
136
590 Nm
M20x110-10.9 ISO 4014
40
33,5:Spw
20-45
30:Spw
50-55
300 NmM16x90-10.9 ISO 4014
75
100(S
DB4)
(S
DB5)
b1
k
125
15
20
250
135 135
c1576v10a
63
"X" "Y" A - A
h1
c1669v05
k1
k0
m0
e
d
A
A
a
Y
H4-H9
min 305*
F5-F8
min 250*
m2
X
a150
(1
55:h1=415)
12
F4
m1
b1 54 59 64 69 74 79 84 89 94 99k*3
40 45(A45)
50 55(A55)
60 65(A65)
70 75(A75)
80 85L1 b1[m] [mm]
L1 < 20 +020 < L1 < 30 +530 < L1 < 35 +10
TypType a max. [mm]F4 F5 F7 F8 H4 H5 H7 H9LT-25-25 930 570 - - 820 600 160 -LT-25-32 1580 1220 760 480 1470 1250 810 310LT-25-40 2430 2070 1610 1330 2320 2100 1660 1160LT-25-45 2930 2570 2110 1830 2820 2600 2160 1660
TypType
h1
LT-25-25/32 315
LT-25-40/45 415
Anschluss seitlich/obenSide/top connectionFixation latrale/par le haut
Anschluss obenTop connectionFixation par le haut
LT-25
L1zul
*1
Typ
Type
k0 k1
[m] [mm] [mm] *218,5 LT-25-25 2500 2830 90623,5 LT-25-32 3150 3480 102030 LT-25-40 4000 4330 1342
33,5 LT-25-45 4500 4830 1450
TypType
Rzul[kN] *4
F4 F4 F5
LT-25-25 128,0 160,9 160,9-32 101,6 160,9 150,3-40 80,0 160,0 118,3-45 bei/for/pour Spw [mm]
1400 71,1 120,9 105,21800 71,1 132,8 105,22240 71,1 142,2 105,2
>2500 71,1 142,2 105,2
TypType
Rzul[kN] *4F5 F7 F8
LT-25
-25 160,9 - -
-32 160,9 160,9 160,9-40 160,9 160,9 160,9-45 bei/for/pour Spw [mm]
1400 120,9 120,9 120,91800 132,8 132,8 132,82240 152,4 152,4 152,4
>2500 160,9 160,9 160,9
TypType
Rzul[kN] *4
LT-25 H4 H5 H7 H9-25 160,9 160,9 160,9 --32 160,9 160,9 160,9 160,9-40 160,9 160,9 160,9 160,9-45 bei/for/pour Spw [mm]
1400 120,9 120,9 120,9 120,91800 132,8 132,8 132,8 132,82240 152,4 152,4 152,4 152,4
>2500 160,9 160,9 160,9 160,9
05.05.15/
* Ma nicht gltig bei Verwendung vonAbhebesicherung, Sturmsicherung
*1 Spannweite Kran*2 Gewicht pro Kopftrgerpaar ohne
Anschlussplatten*3 Bei Schienenbreiten45, 55 etc.
Hinweise in Abs. 5.3 beachten*4 Rzulbei Spurmittenma Katze (Spw)
> 1400 mm
* Dimension not applicable when usinganti-jump catch or storm lock device
*1 Crane span*2 Weight per pair of endcarriages without
joint plates*3 For rail widths45, 55, etc. observe notes
in section 5.3*4 Rzulwith crab track gauge (Spw)
> 1400mm
* Dimension pas valable en cas dutilisa-tion dun dispositif anti-soulvement ouune scurit-tempte
*1 Porte du pont roulant*2 Poids par paire de sommiers sans
plaques de fixation*3 Respectez les remarques dans la section
5.3 pour les largeurs de rail 45, 55, etc.*4 Rzulavec cartement du chariot (Spw)
> 1400mm
-
7/25/2019 Pi Kopftraeger Rev 2015-07-20
79/124
LS-T_
03.F
M
10.14 79
AbmessungenDimensionsDimensions
Kopftrger fr ZweitrgerlaufkraneEndcarriages for double girder o.h.t. cranes
Sommiers pour ponts roulants poss bipoutre
2
Buffer
Calculation see "Buffer selectiontable"page 46.
Joint plates
Travel drives
For more details, see Product
information "Travel drives".
Butoirs
Pour le calcul, voir "Slection dubutoir", page 46.
Plaques de fixation
Groupes dentranement
Pour de plus amples informa-
tions, voir Informations sur leproduit "Groupes dentranement".
B B
c1763v01
b2
Profil KastenProfile BoxProfil Caisson
Puffer
Auslegung siehe "Pufferauswahl-tabelle" Seite 46.
Anschlussplatten
Fahrantriebe
Nheres siehe Produktinforma-
tion "Fahrantriebe".
Typ CodeType Code PufferBufferButoir
MaterialMaterialMatriau
d e max. Federwegmax. deflectionmax
top related