sewage pump amacan
Post on 10-Apr-2015
649 Views
Preview:
TRANSCRIPT
DesignationAmacan K 800-380 / 64 U
XG6
Pump typeChannel type impellerDN of discharge pipe [mm]Impeller diameter [mm]Motor power P2 in kW
(only correct for U motor designs)
Number of poles in the motor
Motor design U/U1/U2 = product temperature 30 �CX/X1/X2 = flameproof, product temperature 40�C
Material codeG = grey cast iron
G1= grey cast iron with variantsG3= sea water design
Automation products available:
� PumpExpert� Hyamaster� hyatronic
Baureihenheft Amacan K1579.5/3--10
ApplicationsSewage pumps, mixed water pumps and activated sludgepumps in sewage treatment plants, irrigation and drainagepumping stations. Storm water pumps for flood protection,water pollution control and industrial refuse tip effluents, forpumping all pre--screened or pre--settled media not liable totwist.
Operating dataHeads H up to 30 mCapacity-- standard programme : Q up to 1000 l/s-- custom--made programme : Q up to 2000 l/sMotor power P2 up to 320 kWProduct temperature: up to 40 �Cmax. submersion level: 20 m
DesignWet installed, close--coupledpumpwith channel--type impeller,single--stage, single--entry, for installation in discharge pipes.
DriveThree-phase asynchronous motor, winding acc. to IEC 38 for400/690V supply voltage (also suitable for 380 V and 415 Vmains), enclosure type 58 to IEC 34-5/IP 68 to DIN 40050,motor design to VDE 0530 part 1/IEC 34--1, insulation class F,for flameproof units also VDE 0171/5.78 parts 1 and 5/EN 50014/EN 50018, protection type EEx d IIB T3.
Bearings-- up to motor sizes 646, 548 :
grease lubricated, maintenance--freeanti--friction bearings
-- up to motor sizes 806, 678, 4310 :grease lubricated anti--friction bearings,re--lubrication without dismantling the pumpset.
Shaft sealingShaft sealing is effected by means of two elastomer bellowsmechanical seals in tandem arrangement, independent of thedirection of rotation. A liquid chamber filled withenvironment--friendly non--toxic paraffin oil between the sealsensures cooling and lubrication.
Submersible motor pump withchannel-type impeller for
installation in discharge pipes
OW 380 092-00
MaterialsPump casing GG-25Motor housing GG-25Pump shaft C 45 NShaft prot. sleeve 1.4021.05Impeller GG-25/Noridur �
Nuts and bolts A 4/1.4462Casing wear ring GG-25/VG 434Cathodic corrosion protection available
Q [l/s]
Q [m3/h]
Standard programme
Custom--made programme
H [m]
Amacan K
2
Selection chart 50 Hz
H [m]
Q [l/s]
Q [m3/h]
Amacan K
3
Range chart 60 Hz
Amacan K
4
Product advantages to the benefit of our customers
Two- or three-channelimpeller with largefree passage
The illustration shown corresponds to Amacan K 1000--420
Especially designed lug for receivingcrane hook allows installation andremoval even when inlet chamber isflooded.(No need to enter the pit!)
The cable entry is completely watertight withinsulation at several points:1. Long rubber gland2. Cable embedded in cast resin3. Conductors embedded in cast resin4. Soldered strandsEven in the event of damage to thecable and core insulation there is nopossibility of moisture entering themotor chamber along the strands dueto capillary action.
Increased efficiency thanks to motorshaft made of ferromagnetic steel
Cable mounted with strain relief.
Operationally safe, dry, three-phaseasynchronous motor, surface cooled,in acc. with VDE regulations (from theKSB submersible pump range)
Motor housing with statorremovable after loosening the flangeconnections(simple visual inspection of the motor)
Patented, standard moisturesensor as additional safetydevice.
Early fault detection by means ofbearing temperature monitoring(from motor /286 and /258 onwards)
Inspection ports for separatefunctional test of mechanical seals
Shaft sleeve protects the pumpshaft against corrosion
Mechanical seals in tandemarrangement, trouble-freeoperation guaranteed for manyyears due to a common liquidfeed with large air cushion forexpansion and high quality, wear--resistant sealing materials.
Mechanical seal monitored bymeans of float switchin the leakage chamber
Thermal protection prevents motorfrom overheating
Self-centering positioning ofthe pump in the dischargecolumn by its own weight.Sealing ensured by an O-ring.No additional anchoring orrotational protection required.Fast installation and removalof pump as disconnection ofpipes and cables is notnecessary.
High operational safety dueto protected sealing chamber.
Renewable casing wear ringprotects casing against wear
OW 380 109-00
Amacan K
5
Table of Contents
Programme and scope of supply, order data, general comments Page 6
Table of pumped media, impeller types Page 7
Modes of installation Page 8
Technical data, warranty, testing and quality assurance, operation withfrequency converter, materials, coating Pages 9 -- 12
Connection of monitoring equipment Pages 13
General drawings Pages 14 -- 17
Mechanical seal -- detail Pages 18 -- 19
Dimension tables -- pump/discharge pipe Pages 20 -- 23
Installation plans Pages 24 -- 29
Pump with suspension wire and turnbuckle in discharge pipe, dischargepipe cover with cable entry Pages 30 -- 32
Selection table -- example Page 33
Characteristic curves Pages 34 -- 55
For further motor datarefer to motor documentation: Amarex KRT Reference-No. 2553.53/...-90
Amacan K
6
ProgrammeStandard pump programme : pumpsets up to sizes 1200-540, n = 980 1/min as described in this brochure
Custom-made programme : pumpsets from size 1200-540 on, n = 980 1/min, motor power P2 > 200 kW with various drives.Hydraulic data on request.
Scope of supplyBasic version : pump unit complete and ready for installation, 400 V / 50 Hz, supplied with10 m power cable,
without performance test(deviations from the basic version will result in extra charges and longer delivery period).
Accessories available / required:-- steel discharge pipes in various designs-- lifting rope complete with cable protection
(obligatory from 3.5 m of free cable length in the discharge pipe onwards)-- monitoring unit
General commentsOur pump units comply with enclosure type IP 68 in accordance with DIN 40050 and therefore include the lesserrequirements of IP 58 of IEC 34--5 valid since April 1, 1988.During production the pumps and motors are subjected to functional tests both independently and as a unit.Head and power rating apply only to pumped liquids with a density of ρ = 1 kg/dm3 and kinematic viscosityν up to 20 mm2/s.
Motor ratings P2 should have a safety factor which is adequate for a particular pumping application(see selection example on page 33).To facilitate transportation the electrical cabling will be supplied separately from cross--sectional area 4x50 mm2 upwards.Applicable drawing numbers are indicated below the drawings.
Order data-- Designation of pump unit according to ”Designation” / ”Selection of pump”-- Capacity Q-- Total head H (Hgeo and plant losses)-- Liquid handled and liquid temperature-- Voltage, frequency, starting method, length of cable-- Accessories required -- (for discharge pipes, please indicate installation mode and relevant levels)-- Quantity and language of operating instructions
Closed channel--type impeller (K impeller)for contaminated non--gaseous liquidscontaining solids, not liable to twist
Note:K-impellers are trimmed to meet the exact duty point.
Amacan K
7
List of liquids handledThe application of submersible pumps is versatile and subject to local conditions which are distinct from case to case.The following list serves as recommendation only!For profound counselling in all questions of planning, consult your nearest KSB sales agency or our technical divisions.
Liquid handled 1)
The end user should decide whetherflameproof motors are necessary
Indication, recommendation
Dirty waterRiver water free impeller passage, larger than solids occuringRain water
free impeller passage, larger than solids occuringprescreened or pre--settled if necessary
Sewagep esc ee ed o p e se ed ecessa y
Activated sludge max. 3% dry substance content
Sea water material combination G3, tmax = 30 �C,anode check every 6 months
Industrial effluent, contaminated with ...-- paint suspension free of solvents, refer to operator’s instructions!-- varnish suspension free of solvents, for silicon--free version consult KSB-- fibrous material short fibres, not liable to twist-- abrasive material variant ”G1” 3) - 0.5 g/l max. solids content
Industrial effluent, slightly acid ph-Wert � 6variant ”G1” 3) plus INERTOL POXITAR coating
Chemically neutral waste water-- ammonia water-- ammonia hydroxide 5% NH4OH-- urea 25% (NH2)2-CO-- potassium hydroxide 10% KOH-- calcium hydroxide 5% Ca(OH)2-- sodium hydroxide 5% NaOH-- sodium carbonate 30% Na2CO3
Chemically neutral waste water contaminatedwith ...
-- aliphatic hydrocarbonse.g. oils, petrol, butane, methane
with polyamide cable sheath or Tefzel cable 2)
-- aromatic hydrocarbonse.g. benzene, styrene
FPM(VITON)O-rings andTEFZEL cable 2)
-- chlorinated hydrocarbonse.g. trichlorethylene, ethylene chloride,
chloroform, methylene chloride
FPM(VITON)O-rings andTEFZEL cable 2)
1) Liquids not mentioned here require in most of the cases upgraded materials. Please consult KSB.2) Modified fluoropolymer ETFE, standard variant (page 10 und 11) to be ordered separately3) Standard variant (page 12) to be ordered separately
Impeller type
Amacan K
8
Types of installation
Steel discharge pipewith underfloor discharge
CU
DU Steel discharge pipewith floor-mounted dischargenozzle
Steel discharge pipeoverflow design
BU
CS Design variant of installationmode CU, under installationcover in floor, foot--mounted(on request)
OW 380 086--00 OW 380 088--00
OW 380 089--00 OW 380 087--00
Inclined installation on request.
Amacan K
9
Technical data
Size Pipe dia. req.[mm]
n[1/min]
Impellerno. of blades
Free passage[mm]
Standard programme
700-330 700 735 3 70x92
700-330 700 980 3 70x92
700-321 700 735 2 105x115
700-321 700 980 2 105x115
700-324 700 735 3 70
700-324 700 980 3 70
800-370 800 980 3 75
800-380 800 735 3 115x95
800-381 800 735 2 145x135
800-380 800 980 3 115x95
800-381 800 980 2 145x135
1000-420 1000 735 3 126x100
1000-421 1000 735 2 140x150
1000-420 1000 980 3 126x100
1000-421 1000 980 2 140x150
1000-500 1000/1300 * 980 3 145x110
1200-540 1200 590 3 133x150
1200-540 1200/1300 * 735 3 133x150
1200-540 1300 980 3 133x150
Custom--made programme
1200-540 1400 980 3 133x150
1300-520 1300 590 3 145
1300-520 1300/1400 * 735 3 145
1300-750 1400 490 3 180
1300-750 1300/1400 590 3 180
*) depending on the motor size (see page 21)
mechanical
elektrical
= special version---- = not available
= standard
= standard design variant
Amacan K
10
Technical data -- Pumpset
K 700-330K 700-324/321
K 800-370
Pump sizes K 800-380/381
K 1000-420/421
K 1000-500
K 1200-540K 1300-520
Characteristics K 1300-750
Motor versions : 6 - pole 20 6 26 6 28 6 ... 64 6 80 6 ... 120 6 138 6 ... 200 6 260 6 ... 320 6
U = non-flameproof 8 - pole 10 8; 17 8 21 8 25 8 ... 54 8 67 8 ... 107 8 126 8 ... 180 8 225 8 ... 280 8
X = flameproof 10 - pole 43 10 ... 84 10 107 10 ... 170 10 215 10 ... 270 10
12 - pole 132 12 ... 200 12
Typical sectional drawing / motorsize DKN
p.14161; 181
p.15225
p.16280
p.17315
----355
Shaft sealingpump -- motor 2 bellows mech. seals, independent of direction of rotation, in tandem arrangement
Anti-friction bearing withre-lubrication facility ----
Typical mech. seal detail p. .18/19 ill. 1 OW 309 124-00 ill. 2 OW 309 110-00
Elastomers in Viton(for O-Rings and mech. seal)
Enclosure Pressure-tight enclosure IP 58 to IEC 34-5/IP 68 to DIN 40050
Explosionprotection
VDE 0171/1.690171/5.78EN50014/50018
----protection (Ex) dll G3
VDE 0171/1.69 ----
Insulation class F
Windings for 400V/50 Hz mains(suitable for 380 ... 415 V) 400 V delta ; 690 V star
230 V with special winding ----
Windings for500 V with special winding star connectedWindings for
mainsvoltage
690 V with standard winding star connectedvoltageother voltages
Starting mode d.o.l. or star--delta
Motor cooling by surrounding pumped liquid, S 1 operation
Cable length 10 m
Cable length > 10 m (> 50m )
Cable entry U ; X resin filled cable gland
Polyamide cable sheath (for cross sectional area 4 x 35 mm2) ----TEFZEL 1) cable(waterproof over full length)
Operated with frequencyinverter 2) (flameproof version )
1) modified fluoropolymer ETFE2) see page 11
Monitoringpage13
Operatinglim
its
Amacan K
11
Technical data -- Pumpset
K 700-330K 700-324/321
K 800-370
Pump sizes K 800-380/381
K 1000-420/421
K 1000-500
K 1200-540K 1300-520
Characteristics K 1300-750
Motor versions : 6 - pole 20 6 26 6 28 6 ... 64 6 80 6 ... 120 6 138 6 ... 200 6 260 6 ... 320 6
U = non-flameproof 8 - pole 10 8; 17 8 21 8 25 8 ... 54 8 67 8 ... 107 8 126 8 ... 180 8 225 8 ... 280 8
X = flameproof 10 - pole 43 10 ... 84 10 107 10 ... 170 10 215 10 ... 270 10
12 - pole 132 12 ... 200 12
max.permissible
U 25 mpermissiblesubmersionlevel
X 20 m
Pumpedliquid
U 30 �Cliquidtemperature X 40 �C
U automatic on/off when permissible winding temp. has been reached (control circuit)
temperaturecontrol ofthe winding
X 2 separate control circuits -- automatic on/off control when permissible winding temp.has been reached (control circuit)
-- trip control when the flameproof temperature limit hasbeen reached (limitation circuit)
Temp. control of pump-sideanti--friction bearings (PT 100) ----Moisture electrode in the motorhousing
Float switch in the leakagechamber to monitor mech. seal ----
= special version---- = not available
= standard
= standard design variant
Warranty, tests and quality assuranceEvery pump is subjected to a functional test. We grant a warranty for pump performance(non--witnessed) in line withISO 9906/A or similar/equivalent international standards.
Witnessed performance test in acc. with ISO or equivalent standards possible.
The high quality of our pumps is ensured by constant quality checks.
Frequency inverter operationOnly 95 % of the motor power P2 must be utilized.For flameproof units, only thermistor tripping devices with PTB approval must be used.Observe the exception on page 13 (ill. 1).
Amacan K
12
Materials
Material combinations G G1 G3 1)
(Sea water version)
Part No. Designation Materials
101 Pump casing GG-25
113 Intermediate casing GG-25
138 Inlet nozzle 2) GG-25
163 Discharge cover 3) GG-25
230 Impeller GG-25 9.4460 4) 9.4460 4)
350 Bearing housing GG-25
360 Bearing cover GG-25
412 O--ring NBR NBR 5) Viton 6) Viton 6)
421 Shaft seal ring NBR NBR 5)
433.01 Mechanical seal Carbon / cast chrome
433.02 Mechanical seal Silicon carbide / silicon carbide
502 Casing wear ring GG-25 VG 434 VG 434
524 Shaft protecting sleeve 1.4021.05
571 Lifting lug ST 37 7)
811 Motor housing GG-25
812 Motor housing cover GG-25
818 Shaft (rotor): up tomotor DKN 161/181 1.4021.05 1.4057
Shaft (rotor): from motor DKN 225 on C 45 N 8)
834.1/.2 Cable entry GG
div. Bolts 1.4462 / 1.4571
99-16 Anode ---- Zn
818 Shaft (rotor) C 45 N
1) Pump units with cathodic protection: check anode every 6 months2) for pump sizes 1300--520 and 1300--7503) for pump size 700--3304) Noridur5) Nitrile (Perbunan)6) Fluororubber FPM7) Lifting lug in 1.44628) dry shaft in the pump area (shaft-protecting sleeve in chromium steel)
Standard surface coatingStandard: Primer and final coat
Surface treatment: SA 2 1/2 (SIS 055900) AN 1865Corrosion prevention to AA 0080-06-01Primer: iron oxide (dipped) 0.035 mm to 0.040 0.0mTop coat: KSB standard coating, approx.0.070 mm (RAL 5002)
Standard design variant: -- sea water version:Primer and INERTOL POXITARSurface treatment see standardPrimer: see standard + wash primerTop coat: INERTOL POXITAR, approx. 0.250 mm (2-component epoxy-tar coating)
Special surface treatmentAvailable at extra charge and longer delivery periods
10 1120 21
10 11 Connected via thermistortripping device withmanual reset 1)
20 21 Connected directly intothe control circuit of themotor contactor 2)
20 21
10 11
Flameproof ”X”Non-flameproof ”U”
Connected via thermis-tor tripping device withautomatic reset
PTCbi-metal
PT100
15 16 3 4
floatswitch
9
moisturesensor
Thermal monitoring ofpump-side ball bearing
Moisture detection probe inmotor housing
Mechanical seal monitoringvia float switch
Connected via PT100tripping relay e.g. makeKriwantype PT100--2AV
9 Connected to earthleakage circuit breaker,nominal currentleakage 30--50 mA
3 4 Connected for alarm,i.e. switch off
Not required, if suppliedconnect to blank terminal
Ill 2
Ill 5Ill 4Ill 3
Thermal motor monitoring for all other Amacan K sizes
15 16
2120 = identity of conductor
Bi-Metall / PTC = temperature sensor in the winding
PTC
10 1121 22
10 11
21 2221 22
10 11
Thermal motor monitoring for range of capacity > 4 kW to 30 kW
bi-metal
Motor version ”U” and ”W”(non-flameproof)
Motor version ”X” and ”Y”(flameproof)
Connected directlyinto the control circuitof motor contactor
Connected directlyinto the control circuitof motor contactor
Not required, if suppliedconnect to dummyterminal
Connected via thermistortripping with manual reset
Ill 1
Amacan K
13
Connection of monitoring equipment
1) For inverter operation with flameproof requirements, PTB--approved tripping devices are required, e.g. make Siemens type3UN6 with manual reset.
2) KSB tripping device available with both functions
571
914.26920.26550.26
529
322
932.01
421.01
811/81-59
818
834
914.04
412.07
81-17
900.28
81-56
81-44.28
81-18
99-17
902.01920.01
412.04
113
433.01433.02
260 914.10 940.03 101 502 230
412.20
932.03
321.02
914.02
412.02
441
412.03
330
932.02
903
411.03
903.15
0W 383650-00
Amacan K
14
Sectional drawingtypical for sizes < 4 kW to 30 kW
Part No. Part Designation Part No. Part Designation Part No. Part Designation
101 Pump casing 421 Lip seal 818 Rotor
113 Intermediate casing 433 Mechanical seal 834 Cable duct
230 Impeller 502 Casing wear ring 900 Bolt
260 Impeller hub cap 529 Bearing sleeve 902 Stud
321 Radial ball bearing 550 Disc 903 Screw plug
322 Radial roller bearing 571 Lug 914 Socket head cap screw
330 Bearing bracket 81-17 Cable crimp 920 Nut
411 Joint ring 81-18 Cable socket 932 Circlip
412 O-ring 81-56 Moisture protection of motor 99-17 Desiccant
OW 380 103-00
571
550.25
920.25
68-3.2
901.25
550.25
81-97.259-71
914.01
500.04
322932.01
81-22
81-56
81-45
411.26
99-17
914.02
412.09
914.06
421.02500.02
350
903.5411.05
412.04902.01920.01
113411.06
412.20412.06
550.23
901.21
931.01
940.03 260 502 230 101
321901.01550.02
932.02412.02
433.01433.02903.03
412.05
903.04
901.26
412.01
812
421.01500.0180-1
818360
411.04
411.03
550.01
Amacan K
15
General arrangement drawingAmacan K 800-370 to 1000-420/421 , motors 28 6 to 54 8
Part No. Part Designation Part No. Part Designation Part No. Part Designation Part No. Part Designation
101 Pump casing 421 Lip seal 81-56 Moisture protection of motor 931 Lock washer
113 Intermediate casing 433 Mechanical seal 81-97 Cable protector 932 Circlip
230 Impeller 500 Ring 812 Motor casing cover 940 Key
260 Impeller hub cap 502 Casing wear ring 818 Rotor 99-17 Desiccant
321 Radial ball bearing 550 Disc 834 Cable duct
322 Radial roller bearing 571 Lug 901 Hexagon bolt
350 Bearing housing 68-3 Cover plate 902 Stud
360 Bearing cover 80-1 Semi-finished motor 903 Screw plug
411 Joint ring 81-22 Terminal box cover 914 Socket head cap screw
412 O-ring 81-45 Float switch 920 Nut
OW 380 104-00
571
901.26
812914.01
412.01
500.04322
932.01
421.01
412.09
81-22
421.03
500.05
81-56
914.06
412.02914.02
99-17
412.03
81-45
411.26421.02
903.05411.05902.01920.01412.04
412.05
113
411.06
433.01433.02
412.20
412.06
550.23 901.21
931.01940.03
260
502230 101
903.01411.01636.01
500.01520.0180-1
818
360500.03
647
320
901.01550.02932.02
550.01
500.02
350
903.03411.03636.02903.02411.02903.04411.04
A -- A550.25
920.25
68-32
901.25
550.25
81-97.2
59-71
Amacan K
16
General arrangement drawingAmacan K 1000-420/421 to 1300-520 , motors 80 6 to 84 10
Amacan K 1300-520 with inlet nozzle (Part No. 138)
Part No. Part Designation Part No. Part Designation Part No. Part Designation Part No. Part Designation
101 Pump casing 421 Lip seal 80-1 Semi-finished motor 914 Socket head capscrew113 Intermediate casing 433 Mechanical seal 81-22 Terminal box cover
9 S pscrew
230 Impeller 500 Ring 81-45 Float switch 920 Nut260 Impeller hub cap 502 Casing wear ring 81-56 Moisture protection of motor 931 Lock washer320 Anti--friction bearing 520 Sleeve 81-97 Cable protector 932 Circlip322 Radial roller bearing 550 Disc 812 Motor casing cover 940 Key350 Bearing housing 571 Lug 818 Rotor 99-17 Desiccant360 Bearing cover 636 Grease nipple 901 Hexagon bolt411 Joint ring 647 Grease regulator 902 Stud412 O-ring 68-3 Cover plate 903 Screw plug
OW 380 105-00
571
901.26
901.04
914.01
412.01
812
80-1
818
834.01834.03
412.12
69-6
81-56
411.26
902.03920.03
412.02
99-17
914.02
903.05411.05
902.01920.01
81-45
412.04
412.05
113
433.01433.02
940.03 260 931.01 230 101550.23 901.21 412.06 502 412.20
500.04322
932.01903.01411.01
636.01500.01
360
421.03
320
550.01
901.01550.02
421.02
350
903.02411.02
421.01520.01
500.03
647
500.05
932.02
500.02
412.03
903.03411.03
636.02903.04411.04
916.02
914.03
411.06
916.03
Amacan K
17
General arrangement drawingAmacan K 1000-500 to 1300-520 , motors 138 6 to 170 10(Standard programme)Amacan K 1300-520 with inlet nozzle (Part No. 138)
Part No. Part Designation Part No. Part Designation Part No. Part Designation Part No. Part Designation
101 Pump casing 421 Lip seal 80-1 Semi-finished motor 916 Plug113 Intermediate casing 433 Mechanical seal 81-45 Float switch 920 Nut230 Impeller 500 Ring 81-56 Moisture protection of motor 931 Lock washer260 Impeller hub cap 502 Casing wear ring 812 Motor casing cover 932 Circlip320 Anti--friction bearing 520 Sleeve 818 Rotor 940 Key322 Radial roller bearing 550 Disc 834 Cable duct 99-17 Desiccant350 Bearing housing 571 Lug 901 Hexagon bolt360 Bearing cover 636 Grease nipple 902 Stud411 Joint ring 647 Grease regulator 903 Screw plug412 O-ring 69-6 Temperature sensor 914 Socket head cap screw
OW 309 124-00
figure 1
Seal variants for different pump types see table on p.10
433.01
551.01
932.03
433.02
524
562.13
412.17
Amacan K
18
Mechanical seal detail
Part No. Part designation Part No. Part designation
433.01 Mechanical seal 551.01 Spacer sleeve433.02 Mechanical seal 562.13 Parallel pin412.17 O-ring 932.03 Circlip524 Shaft protection sleeve
OW 309 110-00
figure 2
Seal variants for different pump types see table on p.10
433.01
550.03
932.03500.06
914.07
433.02
524
412.17
940.13
Amacan K
19
Mechanical seal detail
Part No. Part designation Part No. Part designation
433.01 Mechanical seal 550.03 Disc433.02 Mechanical seal 914.07 Socket head cap screw412.17 O-ring 932.03 Circlip500.06 Ring 940.13 Key524 Shaft protection sleeve
OW 380 111-00
OW 380 085-00
d7
b20
Amacan K
20
Dimension tables for pump and support ring
Amacan K
21
Pump and support ring all dim. in mm, standard programme up to 1200-540/10710 2, custom--made progr. from 1200-540/2606 upwards
Amacan K . . . - . . . / . . .U/X . h1 h2 d1 d2 b c D d7 b20 h20 f20700-330 / 206 1195 1000
/ 266 1170 975670 556 250 130 711 570 691 60 5/ 108 1195 1000 670 556 250 130 711 570 691 60 5
/ 178 1195 1000
700-324/321 / 206 1195 1000/ 266 1170 975
670 556 250 130 711 570 691 60 5/ 108 1195 1000 670 556 250 130 711 570 691 60 5
/ 178 1195 1000
800-370 / 206 1155 960 250 130/ 266 1130 935 250 130/ 286 1400 1080 760 640 369 232 813 656 793 60 2/ 376 1400 1080 369 232/ 456 1400 1080 369 232
800-380/381 / 266 1225 930 250 130/ 286 2 1495 1175 369 232/ 376 1495 1175 369 232/ 456 1495 1175 369 232/ 646 1600 1280 770 640 369 232 813 656 793 60 2/ 178 1250 1055 250 130/ 218 1225 930 250 130/ 258 1 1495 1175 369 232/ 338 1 1495 1175 369 232
1000-420/421 / 376 1 1575 1255 369 232/ 456 1 1575 1255 369 232/ 646 1 1680 1360 369 232/ 806 1 1695 1345 449 232/ 1026 1695 1345 469 232/ 1206 1695 1345 970 840 469 232 1016 856 992 70 8/ 258 2 1575 1255 369 232/ 338 2 1575 1255 369 232/ 438 2 1680 1360 369 232/ 548 1680 1360 369 232
1000-500 / 806 1 1700 1350 449 232/ 1026 1900 1550 469 232 1016 992/ 1206 1900 1550 469 232
(1300-500) / 1386 2150 1770 970 820 577 382 856 70 8/ 1656 2150 1770 577 382 1320 1292/ 2006 2150 1770 577 382
(1300-540) / 1656 2205 1825 577 3821320 1292(1300-540) / 2006 2205 1825 577 382 1320 1292
1200-540 / 848 1955 1605 469 2321220 11921200-540 / 1078 2 1955 1605 469 232 1220 1192
(1300-540) / 1268 2 2205 1825 577 382(1300-540) / 1508 2 2205 1825 1140 960 577 382 1320 1015 1292 70 2(1300-540) / 1808 2 2205 1825 577 382
1320 1292
1200-540 / 4310 1 1765 1415 449 2321200-540 / 5410 2 1955 1605 469 232
1220 11921200-540 / 6710 2 1955 1605 469 232 1220 1192
1200-540 / 8410 2 1955 1605 469 232(1300-540) /10710 2 2205 1825 577 382 1320 1292
(1400-540) / 26062700 1935 1140 960 1420 1015 1192 70 2(1400-540) / 3206 2700 1935 1140 960 -- -- 1420 1015 1192 70 2
1300-520 / 1268 11300-520 / 1508 1 2600
2135577 382 1320 1292
1300-520 / 1808 1 2135
(1400-520) / 2258 1 2900 622 494 1420 13921300-520 / 6710 1
2440 19701250 1100
469 2321155 60 5
1300-520 / 8410 1 2440 1970 469 2321320 12921300-520 / 10710 1
2600 2135 577 3821320 1292
1300-520 / 12610 1 2600 2135 577 382
1300-750 / 17010 2 2585 1920 577 382 1320 1292(1400-750) / 21510 2(1400-750) / 23510 2 2900 2135(1400-750) / 27010 2
1260 920 622 494 1420 1170 1392 60 5(1400-750) / 11012 1260 920 622 494 1420 1170 1392 60 5
(1400-750) / 13012 2585 1920(1400-750) / 15512
2585 1920
(1400-750) / 18012 2900 2135
Steel discharge pipes
Overflow design B Underfloor discharge C
Floor-mounted discharge D Floor-mounted discharge Dpressure--tight
� � to suit � � to suit
OW 380 113-00 OW 380 115-00
OW 380 117-00OW 380 119-00
Amacan K
22
Dimension table, discharge pipes
Amacan K
23
Main dimensions -- discharge pipes all dimensions in mm
Pump sizes D pipe dia. A DN2 min DN2 max H1 min H3 min H1,H3 max H2 min H0 max
700-330 711 700 650 300 600 1900 2570 670 7820
700-324/321 711 700 650 300 600 1900 2570 670 7820
800-370 813 800 700 400 700 2080 2850 10000 770 7580
800-380/381 813 800 700 400 700 2250 302010000
770 7410
1000-420/421 1016 1000 810 600 900 2520 3490 (dischargepipes longer
925 7040
1000-500 1016 1000 810 600 900 2730 3700pipes longer
than 925 6830
1320 1300 960 1000 1300 3280 4660than
10,000 mmon request)
1130 6080
1200-540 1220 1200 910 900 1200 2930 4200on request)
1080 6480
1320 1300 960 1000 1300 3280 4660 1130 6080
1420 1400 1010 1100 1400 3640 5000 1180 5660
1300-520 1320 1300 960 1000 1300 3110 4500 1130 6240
1420 1400 1010 1100 1400 3380 4800 1180 5920
1300-750 1320 1300 960 1000 1300 3420 4800 1130 5930
Pump sizes D H4 M1 M2 M3 M4 N1 N2 N3 N4
700-330 711 500 800 1150 1160 1080 1160 910 455 695
700-324/321 711 500 800 1150 1160 1080 1160 910 455 695
800-370 813 550 900 1250 1260 1250 1260 1010 505 745
800-380/381 813 550 900 1250 1260 1250 1260 1010 505 745
1000-420/421 1016 650 1120 1460 1460 1450 1460 1210 605 855
1000-500 1016 650 1120 1460 1460 1450 1460 1210 605 855
1320 1000 1450 1760 1760 1700 1900 1510 755 1005
1200-540 1220 930 1350 1670 1670 1600 1800 1410 710 960
1320 1000 1450 1760 1760 1700 1900 1510 755 1005
1420 1050 1550 1870 1870 1900 2040 1610 810 1060
1300-520 1320 1000 1450 1760 1760 1700 1900 1510 755 1005
1420 1050 1550 1870 1870 1900 2040 1610 810 1060
1300-750 1320 1000 1450 1760 1760 1700 1900 1510 755 1005
Wall thickness against dia. D:-- up to size 800-380/381: 8 mm-- sizes 1000-420/421, 1000-500 with pipe diameter 1000 mm: 10 mm-- sizes 1000-500 with pipe diameter 1300 mm, 1200-540: 12 mm
Discharge flanges to ISO 7005/2 / DIN 2501, PN 6
Admissible deviations for dimensions without tolerance indication:-- flange dimensions: ISO 2768 medium-- welding constructions: B/F to DIN EN ISO 13920
Subject to technical modifications
OW 380 120--00
View Y
0-45�
Y
Section A -- A
100
350
d7
h üh a
X
t 1Hgeo
t 3
t 4t 2
e1
D
s 1/2min
s 1min
s 1min
p2
p 2100
p 1
Foundation holes
View X(without pump)
Foundation holes
Support plate-- discharge pipes
A
A
Minimumwater level
Recommendedinflow direction
Amacan K
24
Installation planInstallation example Installation mode BU
Head loss diagram
H = Hgeo + hü + v2/2g
Allowances for sumpdimensions to DIN 18202,part 4, group B
v as a function of DA
Diagram for minimumwater level t1
Amacan K 1300-750
OW
380110--00
700--324/321
Overflow head hü
hü [m]
Q [m3/s]
Overflow head ”hü” dependent on Q and the design of outletdiam. DA. The characteristic curves only apply for dischargeunobstructed on all sides; otherwise to be regarded as anapproximation.
Amacan K
25
Main dimensions of discharge pipe and pump sump all dimensions in mm
Pump sizes D*) t2 t3 t4 min t4 max d7 e1700-330 711 330 200 1900 570 430700-324/321 711 330 200 1900 570 430800-370 813 330 200 2080 656 480800-380/381 813 410 250 2250
10000656 480
1000-420/421 1016 435 250 252010000
856 6001000-500 1016 480 300 2730 (discharge
pipes856 600
1320 480 300 3280
( gpipes
longer than 856 7501200-540 1220 585 350 2930
longer than10,000 mmon request)
1015 7001320 585 350 3280
,on request) 1015 750
1300-520 1320 1025 400 3570 1155 7501420 1025 400 3670 1155 800
1300-750 1320 940 480 3740 1170 750
Pump sizes D*) s1 min p1 p2 ha700-330 711 1000 900 640 100700-324/321 711 1150 900 640 100800-370 813 1150 1000 740 100800-380/381 813 1400 1000 740 100
1000-420/421 1016 1600 1220 960 1001000-500 1016 1800 1220 960 100
1320 1800 1550 1260 1001200-540 1220 2250 1450 1160 100
1320 2250 1550 1260 1001300-520 1320 2250 1550 1260 100
1420 2250 1650 1360 1001300-750 1320 2700 1550 1260 100
*) from size 1000-500 onwards, D depends on motor size, see page 21
Subject to technical modifications
OW 380 121-00
DN2 can be chosen with regard to the desired outlet speed.See table DN2min/DN2max and head loss diagram.
1
s 1/2min
s 1min
s 1min
Recommendedinflow direction
0-45�
e
Y
X
t 1Hgeo
Minimumwater level
t 3
t 4t 2
D
Vent pipe
t 5
DN2
a
A
A
View Y
Section A -- A
d7
250
300
200
Foundation holes
p2
a 2200
p1
a 1
a 3
200
View X(without discharge pipe cover,
without pump)
Foundation holes
Support plate-- discharge pipe
Amacan K
26
Installation planInstallation example Installation mode CU
Head loss diagramAllowances for sumpdimensions to DIN 18202,part 4, group B
H = Hgeo + HV ges
HV ges includes:
-- elbow-- disch. pipe length = 5xDN2-- check valve-- outlet loss v2/2g
OW
380110--00
Diagram for minimumwater level t1
Amacan K 1300-750
700--324/321
HV ges [m]
Q [m3/s]
Amacan K
27
Main dimensions of discharge pipe and pump sump all dimensions in mm
Pump sizes D*) t2 t3 t4 min t4 max d7 e1 s1 min700-330 711 330 200 2570 570 430 1000700-324/321 711 330 200 2570 570 430 1150800-370 813 330 200 2850 656 480 1150800-380/381 813 410 250 3020 10000 656 480 1400
1000-420/421 1016 435 250 349010000
856 600 16001000-500 1016 480 300 3700 (discharge
pipes856 600 1800
1320 480 300 4660 pipeslonger than 856 750 1800
1200-540 1220 585 350 4200longer than10,000 mm 1015 700 2250
1320 585 350 466010,000 mmon request) 1015 750 2250
1300-520 1320 1025 400 5350
q )
1155 750 22501420 1025 400 5550 1155 800 2250
1300-750 1320 940 480 5520 1170 750 2700
Pump sizes D*) p1 p2 DN2 min DN2 max a a1 a2 a3 t5 min700-330 711 860 960 300 600 650 1100 850 430 670700-324/321 711 860 960 300 600 650 1100 850 430 670800-370 813 960 1060 400 700 700 1200 950 480 770800-380/381 813 960 1060 400 700 700 1200 950 480 770
1000-420/421 1016 1160 1260 600 900 810 1410 1160 580 9251000-500 1016 1160 1260 600 900 810 1410 1160 580 925
1320 1600 1700 1000 1300 960 1710 1460 730 11301200-540 1220 1500 1600 900 1200 910 1620 1370 685 1080
1320 1600 1700 1000 1300 960 1710 1460 730 11301300-520 1320 1600 1700 1000 1300 960 1710 1460 730 1130
1420 1740 1840 1100 1400 1010 1820 1570 785 11801300-750 1320 1600 1700 1000 1300 960 1710 1460 730 1130
*) from size 1000-500 onwards, D depends on motor size, see page 21
Subject to technical modifications
OW 380 122-00
DN2 can be chosen with regard to the desired outlet speed.See table DN2min/DN2max and head loss diagram.
1
s 1/2min
s 1min
s 1min
e
Recommendedinflow direction
0-45�
Y
t 1
Minimumwater level
Vent pipe
A
A
X
DN2
a
Dt7
t 3
H4
t 6t 4
t 2
d7
250
300
200
Section A -- A
View Y
p2
a 2200
p1
a 1
200
Foundation holes(without pump)
Foundationholes
Support plate-- discharge pipe
View X
Amacan K
28
Installation planInstallation example Installation mode DU
-- not pressure sealed
Head loss diagram Allowances for sumpdimensions to DIN 18202,part 4, group BH =
Hgeo + hV Kr + HV Anl
Except for hV Krall losses must be calculatedwith a view to plant conditions
OW
380110--00
Diagram for minimumwater level t1 Amacan K 1300--750
700--324/321
hV Kr [m]
Q [m3/s]
Amacan K
29
Main dimensions of discharge pipe and pump sump all dimensions in mm
Pump sizes D*) t2 t3 t4 min t4 max d7 e1 s1 min p1 p2700-330 711 330 200 1250 8680 570 430 1000 860 960700-324/321 711 330 200 1250 8680 570 430 1150 860 960800-370 813 330 200 1430 8580 656 480 1150 960 1060800-380/381 813 410 250 1600 8580 656 480 1400 960 1060
1000-420/421 1016 435 250 1765 8275 856 600 1600 1160 12601000-500 1016 480 300 1975 8275 856 600 1800 1160 1260
1320 480 300 2180 7520 856 750 1800 1460 15601200-540 1220 585 350 1860 7660 1015 700 2250 1360 1460
1320 585 350 2180 7520 1015 750 2250 1460 15601300-520 1320 1025 400 2740 7520 1155 750 2250 1460 1560
1420 1025 400 2840 7420 1155 800 2250 1560 16601300-750 1320 940 480 2910 7520 1170 750 2700 1460 1560
Pump sizes D*) DN2 min DN2 max a a1 a2 t6 min t6 max H4 t7 max700-330 711 300 600 650 860 610 820 8250 500700-324/321 711 300 600 650 860 610 820 8250 500800-370 813 400 700 700 960 710 870 8020 550800-380/381 813 400 700 700 960 710 870 7850 550
100001000-420/421 1016 600 900 810 1160 910 1075 7585 650
10000
1000-500 1016 600 900 810 1160 910 1075 7375 650 (dischargepipes1320 1000 1300 960 1460 1210 1480 6820 1000
( gpipes
longer than1200-540 1220 900 1200 910 1360 1110 1410 7210 930
longer than10,000 mmon request)1320 1000 1300 960 1460 1210 1480 6820 1000,
on request)
1300-520 1320 1000 1300 960 1460 1210 1460 6260 10001420 1100 1400 1010 1560 1310 1530 6110 1050
1300-750 1320 1000 1300 960 1460 1210 1480 6090 1000*) from size 1000-500 onwards, D depends onmotor size, see page 21
OW 380 090-00
Part list
Cross-section of carrier cable arrangement(Where free cable length in discharge pipe exceeds 3.5 m,this arrangement is absolutely necessary)
Cable length in discharge pipe exceeding 3.5 m:Mounting of tensioning device 59-8-- closed discharge pipe: on the discharge pipe cover
(see ill. above)-- open discharge pipe of installation mode BU on a
girder above water level, to be supplied on site
Cable length in discharge pipe under 3.5 m:On open discharge pipe: electrical cables must bemounted on a girder above water level (to be supplied on site)to avoid damages by the swirl of the water.
Plastic hose for clamp
Clamp
Control cable Power supply cable
Carrier cable59-24
SpacerOW 380 091-00
59-8
59-17.2
59-47
59-24
59-17.2
Part No. Part designation Material
59-8 Turnbuckle 1.457159-17.2 Shackle 1.457159-47 Carrier cable 1.475159-24 Carrier cable to DIN 3088,
form PK 1.4401720 Spacer EPDM
Amacan K
30
Pump with suspension wire and tensioning device in discharge pipe turnbuckle
Top view
Section A -- A
OW 380 836-00
1 Discharge pipe cover2 Cover3 Welding sleeve with input bushing acc. to DIN 22 419 with strain relief, protection against buckling and torsion4 Bracket for fixing turnbuckle (cable)5 Gasket, rubber reinforced with fabric
Note: Versions with split cover are possible, too.
12
3
45 5
A
A
Amacan K
31
Discharge pipe cover with cable ductDesign variant: with welding sleeve
Section A -- A
A
A
81 65 4 7
OW 380 861-00
3
2
1 Discharge pipe cover2 Cable gland, type RGP (cable gland)3 Tecron modules (packing and filling)4 Cover segment with cable duct5 Sealing of the cover division with closed cell profile gasket, which may be pre-stressed by inserting an O-ring.6 Division guard7 Holding brackets for cover segment with cable glands8 Gasket, rubber reinforced with fabric
Note: Versions with split cover are possible, too.
Top view
View X
X
Amacan K
32
Discharge pipe cover with cable ductDesign variant: with cable gland
The following steps lead toa correct selection ofpump:
Given data:Capacity Q=400 l/sHead H = 6 mLiquid temp. t=30 �CNon-flameproofMaterial type G
Q [ l/s ]H [m]
Impellerdiameter
With available QH data,the impeller diam. D2A isapprox. 400 mm and thusPduty can be found.
A
B
P2 min
C
Motor size
Motor size is to be se-lected by considering tem-perature and flameproof/non-flameproof designs.
The maximum value ofthe characteristic curve Pthrough Pduty is the mini-mum motor power P2 min
Amacan K 800-381 980 1/min
Pduty
Minimummotor power
P2 min
Nr. : D2A / D2I[mm]
4 : 408 / 3783 398 / 3442 : 384 / 3171 : 367 / 295
H [m]
P [kW]
FörderhöheHead
Hauteur
LeistungsbedarfPower Input
Puiss. hyd. abs.
Förderstrom/Rate of Flow/Débit
LaufradformImpeller type
Forme de roue
freier Durchgangfree passage
section de passage
145 x 135 mm
H [ft]
P [hp]
Amacan K
33
Selection table -- Example
400 V 50 Hz 3~ (winding 400/690 V) max. temperature of liquid handled 30/40�C
Motor Motor Amacan K Code Irated Istarting 1) cos � Electric cables NSSHöu-J Weight
design rating 800-381/... Nr. d.o.l. Power supply cable Control
U or X P2 Cross-section Outside dia cable 2)
(Flameproof) kW A A mm2 mm kg
24 .../266 U 48.5 225 0.84 1x(7x10+5x1.5) 29.5--32.9 -- 730U 28 .../286 U 60.0 250 0.78 2x4x4 16.6-18.7 A 780
tmax = 30 �C 37 .../376 U 77.0 335 0.78 2x4x6 17.8-19.8 A 870tmax = 30 C45 .../456 U 92.0 460 0.79 2x4x10 21.7-23.7 A 930
24 .../266 X 48.5 225 0.84 1x(7x10+5x1.5) 29.5--32.9 -- 730X 28 .../376 X 61.0 335 0.75 2x4x4 16.6-18.7 A 870
tmax = 40 �C 37 .../456 X 77.0 460 0.77 2x4x6 17.8-19.8 A 930tmax = 40 C45 .../646 X 106.0 600 0.69 2x4x10 21.7-23.7 A 1030
Selected: Motor version ”U”, (non--flameproof), motor with 37.0 kW, 6--pole
Designation of complete pump set: : Amacan K 800--381 / 376 U GFor further data refer to the tables on pages 34-55 and motor documentation Amarex KRT Rh.-Nr. 2553.53/. . .-90
For a flameproof machine or tmax = 40 �C, motor .../45 6 X G should be used.
Note :Impellers are trimmed to the operating point.The QH data should be clearly stated at the time of ordering, in order to define the exact impeller diameter.
Nr. : D2A / D2I[mm]
4 : 323 / 3233 : 320 / 3052 : 314 / 2801 : 305 / 251H [m]
P [kW]
H [ft]
P [hp]
Kennlinien nachISO 9906/A
Curves as perISO 9906/A.
Courbes selonISO 9906/A.
FörderhöheHead
Hauteur
LeistungsbedarfPower Input
Puiss. hyd. abs.
Förderstrom/Rate of Flow/Débit
LaufradformImpeller type
Forme de roue
freier Durchgangfree passage
section de passage
105 x 115 mm
Amacan K
34
Amacan K 700-321 980 1/min
400 V 50 Hz 3~ (winding 400/690 V) max. temperature of liquid handled 30/40�C
Motor Motor Amacan K Code Irated Istarting 1) cos � Electric cables NSSHöu-J Weight
design rating 700-321/... Nr. d.o.l. Power supply cable Control
U or X P2 Cross-section Outsidedia.
cable
(Flameproof) kW A A mm2 mm kg
U 18 .../206 U 35.5 160 0.85 1x(7x4+5x1.5) 26.9--28.8 -- 430
tmax = 30 �C 24 .../266 U 48.5 225 0.84 1x(7x10+5x1.5) 29.5--32.9 -- 470
X 18 .../206 X 35.5 160 0.85 1x(7x4+5x1.5) 26.9--28.8 -- 430
tmax = 40 �C 24 .../266 X 48.5 225 0.84 1x(7x10+5x1.5) 29.5--32.9 -- 470
Data applies to a density of 1 kg/dm3 and a kinematic viscosity of up to max. 20 mm2/sWarranty acc. to ISO 9906/A1) further starting modes on request
Nr. : D2A / D2I[mm]
4 : 323 / 3233 : 320 / 3052 : 314 / 2801 : 305 / 251
H [m]
P [kW]
H [ft]
P [hp]
Kennlinien nachISO 9906/A
Curves as perISO 9906/A.
Courbes selonISO 9906/A.
FörderhöheHead
Hauteur
LeistungsbedarfPower Input
Puiss. hyd. abs.
Förderstrom/Rate of Flow/Débit
LaufradformImpeller type
Forme de roue
105 x 115 mm
freier Durchgangfree passage
section de passage
Amacan K
35
Amacan K 700-321 735 1/min
400 V 50 Hz 3~ (winding 400/690 V) max. temperature of liquid handled 30/40�C
Motor Motor Amacan K Code Irated Istarting 1) cos � Electric cables NSSHöu-J Weight
design rating 700-321/... Nr. d.o.l. Power supply cable Control
U or X P2 Cross-section Outsidedia.
cable
(Flameproof) kW A A mm2 mm kg
U 10 .../108 U 22.5 65 0.79 1x(12x2.5) 22.7--24.7 -- 410
tmax = 30 �C 16 .../178 U 36.0 115 0.79 1x(7x4+5x1.5) 26.9--28.8 -- 435
X 10 .../108 X 22.5 65 0.79 1x(12x2.5) 22.7--24.7 -- 410
tmax = 40 �C 16 .../178 X 36.0 115 0.79 1x(7x4+5x1.5) 26.9--28.8 -- 435
Data applies to a density of 1 kg/dm3 and a kinematic viscosity of up to max. 20 mm2/sWarranty acc. to ISO 9906/A1) further starting modes on request
Nr. : D2A / D2I[mm]
3 : 324 / 3242 : 309 / 2801 : 290 / 234
H [m]
P [kW]
H [ft]
P [hp]
Kennlinien nachISO 9906/A
Curves as perISO 9906/A.
Courbes selonISO 9906/A.
FörderhöheHead
Hauteur
LeistungsbedarfPower Input
Puiss. hyd. abs.
Förderstrom/Rate of Flow/Débit
LaufradformImpeller type
Forme de roue
70 x 70 mmfreier Durchgang
free passagesection de passage
Amacan K
36
Amacan K 700-324 980 1/min
400 V 50 Hz 3~ (winding 400/690 V) max. temperature of liquid handled 30/40�C
Motor Motor Amacan K Code Irated Istarting 1) cos � Electric cables NSSHöu-J Weight
design rating 700-324/... Nr. d.o.l. Power supply cable Control
U or X P2 Cross-section Outsidedia.
cable
(Flameproof) kW A A mm2 mm kg
U 18 .../206 U 35.5 160 0.85 1x(7x4+5x1.5) 26.9--28.8 -- 430
tmax = 30 �C 24 .../266 U 48.5 225 0.84 1x(7x10+5x1.5) 29.5--32.9 -- 470
X 18 .../206 X 35.5 160 0.85 1x(7x4+5x1.5) 26.9--28.8 -- 430
tmax = 40 �C 24 .../266 X 48.5 225 0.84 1x(7x10+5x1.5) 29.5--32.9 -- 470
Data applies to a density of 1 kg/dm3 and a kinematic viscosity of up to max. 20 mm2/sWarranty acc. to ISO 9906/A1) further starting modes on request
Nr. : D2A / D2I[mm]
3 : 324 / 3242 : 309 / 2801 : 290 / 234
H [m]
P [kW]
H [ft]
P [hp]
Kennlinien nachISO 9906/A
Curves as perISO 9906/A.
Courbes selonISO 9906/A.
FörderhöheHead
Hauteur
LeistungsbedarfPower Input
Puiss. hyd. abs.
Förderstrom/Rate of Flow/Débit
LaufradformImpeller type
Forme de roue
freier Durchgangfree passage
section de passage
70 x 70 mm
Amacan K
37
Amacan K 700-324 735 1/min
400 V 50 Hz 3~ (winding 400/690 V) max. temperature of liquid handled 30/40�C
Motor Motor Amacan K Code Irated Istarting 1) cos � Electric cables NSSHöu-J Weight
design rating 700-324/... Nr. d.o.l. Power supply cable Control
U or X P2 Cross-section Outsidedia.
cable
(Flameproof) kW A A mm2 mm kg
U 10 .../108 U 22.5 65 0.79 1x(12x2.5) 22.7-24.7 -- 410
tmax = 30 �C 16 .../178 U 36.0 115 0.79 1x(7x4+5x1.5) 26.9--28.8 -- 435
X 10 .../108 X 22.5 65 0.79 1x(12x2.5) 22.7-24.7 -- 410
tmax = 40 �C 16 .../178 X 36.0 115 0.79 1x(7x4+5x1.5) 26.9--28.8 -- 435
Data applies to a density of 1 kg/dm3 and a kinematic viscosity of up to max. 20 mm2/sWarranty acc. to ISO 9906/A1) further starting modes on requestt
Nr. : D2A / D2I[mm]
4 : 326 / 3263 : 300 / 2922 : 287 / 2451 : 270 / 214
H [m]
P [kW]
H [ft]
P [hp]
Kennlinien nachISO 9906/A
Curves as perISO 9906/A.
Courbes selonISO 9906/A.
FörderhöheHead
Hauteur
LeistungsbedarfPower Input
Puiss. hyd. abs.
Förderstrom/Rate of Flow/Débit
LaufradformImpeller type
Forme de roue
freier Durchgangfree passage
section de passage
70 x 92 mm
Amacan K
38
Amacan K 700-330 980 1/min
400 V 50 Hz 3~ (winding 400/690 V) max. temperature of liquid handled 30/40�C
Motor Motor Amacan K Code Irated Istarting 1) cos � Electric cables NSSHöu-J Weight
design rating 700-330/... Nr. d.o.l. Power supply cable Control
U or X P2 Cross-section Outsidedia.
cable
(Flameproof) kW A A mm2 mm kg
U 18 .../206 U 35.5 160 0.85 1x(7x4+5x1.5) 26.9--28.8 -- 430
tmax = 30 �C 24 .../266 U 48.5 225 0.84 1x(7x10+5x1.5) 29.5--32.9 -- 470
X 18 .../206 X 35.5 160 0.85 1x(7x4+5x1.5) 26.9--28.8 -- 430
tmax = 40 �C 24 .../266 X 48.5 225 0.84 1x(7x10+5x1.5) 29.5--32.9 -- 470
Data applies to a density of 1 kg/dm3 and a kinematic viscosity of up to max. 20 mm2/sWarranty acc. to ISO 9906/A1) further starting modes on request
Nr. : D2A / D2I[mm]
4 : 326 / 3263 : 310 / 3102 : 295 / 2661 : 278 / 231
H [m]
P [kW]
H [ft]
P [hp]
Kennlinien nachISO 9906/A
Curves as perISO 9906/A.
Courbes selonISO 9906/A.
FörderhöheHead
Hauteur
LeistungsbedarfPower Input
Puiss. hyd. abs.
Förderstrom/Rate of Flow/Débit
LaufradformImpeller type
Forme de roue
freier Durchgangfree passage
section de passage
70 x 92 mm
Amacan K
39
Amacan K 700-330 735 1/min
400 V 50 Hz 3~ (winding 400/690 V) max. temperature of liquid handled 30/40�C
Motor Motor Amacan K Code Irated Istarting 1) cos � Electric cables NSSHöu-J Weight
design rating 700-330/... Nr. d.o.l. Power supply cable Control
U or X P2 Cross-section Outsidedia.
cable
(Flameproof) kW A A mm2 mm kg
U 10 .../108 U 22.5 65 0.79 1x(12x2.5) 22.7-24.7 -- 410
tmax = 30 �C 16 .../178 U 36.0 115 0.79 1x(7x4+5x1.5) 26.9--28.8 -- 435
X 10 .../108 X 22.5 65 0.79 1x(12x2.5) 22.7-24.7 -- 410
tmax = 40 �C 16 .../178 X 36.0 115 0.79 1x(7x4+5x1.5) 26.9--28.8 -- 435
Data applies to a density of 1 kg/dm3 and a kinematic viscosity of up to max. 20 mm2/sWarranty acc. to ISO 9906/A1) further starting modes on request
Nr. : D2A / D2I[mm]
4 : 370 / 3703 340 / 3402 : 318 / 3031 : 300 / 278
H [m]
P [kW]
H [ft]
P [hp]
Kennlinien nachISO 9906/A
Curves as perISO 9906/A.
Courbes selonISO 9906/A.
FörderhöheHead
Hauteur
LeistungsbedarfPower Input
Puiss. hyd. abs.
Förderstrom/Rate of Flow/Débit
LaufradformImpeller type
Forme de roue
freier Durchgangfree passage
section de passage
75 mm
Amacan K
40
Amacan K 800-370 980 1/min
400 V 50 Hz 3~ (winding 400/690 V) max. temperature of liquid handled 30/40�C
Motor Motor Amacan K Code Irated Istarting 1) cos � Electric cables NSSHöu-J Weight
design rating 800-370/... Nr. d.o.l. Power supply cable Control
U or X P2 Cross-section Outsidedia.
cable 2)
(Flameproof) kW A A mm2 mm kg
18 .../206 U 35.5 160 0.85 1x(7x4+5x1.5) 26.9--28.8 -- 505
U 24 .../266 U 48,.5 225 0.84 1x(7x10+5x1.5) 29.5--32.9 -- 565
tmax = 30 �C 28 .../286 U 60.0 250 0.78 2x4x4 16.6--18.7 A 710max
37 .../376 U 77.0 335 0.78 2x4x6 17.8--19.8 A 780
18 .../206 X 35.5 160 0.85 1x(7x4+5x1.5) 26.9--28.8 -- 505
X 24 .../266 X 48.5 225 0.84 1x(7x10+5x1.5) 29.5--32.9 -- 565
tmax = 40 �C 28 .../376 X 61.0 335 0.75 2x4x4 16.6--18.7 A 780max
37 .../456 X 77.0 460 0.77 2x4x6 17.8--19.8 A 860
Data applies to a density of 1 kg/dm3 and a kinematic viscosity of up to max. 20 mm2/sWarranty acc. to ISO 9906/A1) further starting modes on request2) Control cable: A = 1x8x1.5 ; Outside: 16.5--18.7 mm ; B = 1x10x1.5 ; Outside : 18.7--20.7 mm
H [m]
P [kW]
H [ft]
P [hp]
Kennlinien nachISO 9906/A
Curves as perISO 9906/A.
Courbes selonISO 9906/A.
FörderhöheHead
Hauteur
LeistungsbedarfPower Input
Puiss. hyd. abs.
Förderstrom/Rate of Flow/Débit
LaufradformImpeller type
Forme de roue
freier Durchgangfree passage
section de passage
115 x 95 mm
Nr. : D2A / D2I[mm]
4 : 388 / 3633 376 / 3412 : 355 / 3061 : 332 / 268
Amacan K
41
Amacan K 800-380 980 1/min
400 V 50 Hz 3~ (winding 400/690 V) max. temperature of liquid handled 30/40�C
Motor Motor Amacan K Code Irated Istarting 1) cos � Electric cables NSSHöu-J Weight
design rating 800-380/... Nr. d.o.l. Power supply cable Control
U or X P2 Cross-section Outsidedia.
cable 2)
(Flameproof) kW A A mm2 mm kg
28 .../286 U 60.0 250 0.78 2x4x4 16.6--18.7 A 780
U 37 .../376 U 77.0 335 0.78 2x4x6 17.8--19.8 A 870
tmax = 30 �C 45 .../456 U 92.0 460 0.79 2x4x10 21.7--23.7 A 930max
64 .../646 U 139.0 600 0.75 2x4x16 27.1--30.1 A 1030
X28 .../376 X 61.0 335 0.75 2x4x4 16.6--18.7 A 870
X
t = 40 �C37 .../456 X 77.0 460 0.77 2x4x6 17.8--19.8 A 930
tmax = 40 �C 45 .../646 X 106.0 600 0.69 2x4x10 21.7--23.7 A 1030
Data applies to a density of 1 kg/dm3 and a kinematic viscosity of up to max. 20 mm2/sWarranty acc. to ISO 9906/A1) further starting modes on request2) Control cable: A = 1x8x1.5 ; Outside: 16.5--18.7 mm ;
Nr. : D2A / D2I[mm]
4 : 388 / 3633 376 / 3412 : 355 / 3061 : 332 / 268
H [m]
P [kW]
H [ft]
P [hp]
Kennlinien nachISO 9906/A
Curves as perISO 9906/A.
Courbes selonISO 9906/A.
FörderhöheHead
Hauteur
LeistungsbedarfPower Input
Puiss. hyd. abs.
Förderstrom/Rate of Flow/Débit
LaufradformImpeller type
Forme de roue
freier Durchgangfree passage
section de passage
115 x 95 mm
Amacan K
42
Amacan K 800-380 735 1/min
400 V 50 Hz 3~ (winding 400/690 V) max. temperature of liquid handled 30/40�C
Motor Motor Amacan K Code Irated Istarting 1) cos � Electric cables NSSHöu-J Weight
design rating 800-380/... Nr. d.o.l. Power supply cable Control
U or X P2 Cross-section Outsidedia.
cable 2)
(Flameproof) kW A A mm2 mm kg
U16 .../178 U 36.0 115 0.79 1x(7x4+5x1.5) 26.9--28.8 -- 630
U
t = 30 �C20 .../218 U 44.0 150 0.75 1x(7x10+5x1.5) 29.5--32.9 -- 700
tmax = 30 �C25 .../258 U1 57.0 230 0.73 2x4x4 16.9-18.7 A 870
X16 .../178 X 36.0 115 0.79 1x(7x4+5x1.5) 26.9--28.8 -- 630
X
t = 40 �C20 .../218 X 44.0 150 0.75 1x(7x10+5x1.5) 29.5--32.9 -- 700
tmax = 40 �C25 .../338 X1 60.0 300 0.69 2x4x4 16.6-18.7 A 930
Data applies to a density of 1 kg/dm3 and a kinematic viscosity of up to max. 20 mm2/sWarranty acc. to ISO 9906/A1) further starting modes on request2)Control cable: A = 1x8x1.5 ; Outside: 16.5--18.7 mm ; B = 1x10x1.5 ; Outside: 18.7--20.7 mm
Nr. : D2A / D2I[mm]
4 : 408 / 3783 398 / 3442 : 384 / 3171 : 367 / 295
H [m]
P [kW]
H [ft]
P [hp]
Kennlinien nachISO 9906/A
Curves as perISO 9906/A.
Courbes selonISO 9906/A.
FörderhöheHead
Hauteur
LeistungsbedarfPower Input
Puiss. hyd. abs.
Förderstrom/Rate of Flow/Débit
LaufradformImpeller type
Forme de roue
freier Durchgangfree passage
section de passage
145 x 135 mm
Amacan K
43
Amacan K 800-381 980 1/min
400 V 50 Hz 3~ (winding 400/690 V) max. temperature of liquid handled 30/40�C
Motor Motor Amacan K Code Irated Istarting 1) cos � Electric cables NSSHöu-J Weight
design rating 800-381/... Nr. d.o.l. Power supply cable Control
U or X P2 Cross-section Outsidedia.
cable 2)
(Flameproof) kW A A mm2 mm kg
24 .../266 U 48.5 225 0.84 1x(7x10+5x1.5) 29.5--32.9 -- 730
U 28 .../286 U 60.0 250 0.78 2x4x4 16.6-18.7 A 780
tmax = 30 �C 37 .../376 U 77.0 335 0.78 2x4x6 17.8-19.8 A 870max
45 .../456 U 92.0 460 0.79 2x4x10 21.7-23.7 A 930
24 .../266 X 48.5 225 0.84 1x(7x10+5x1.5) 29.5--32.9 -- 730
X 28 .../376 X 61.0 335 0.75 2x4x4 16.6-18.7 A 870
tmax = 40 �C 37 .../456 X 77.0 460 0.77 2x4x6 17.8-19.8 A 930max
45 .../646 X 106.0 600 0.69 2x4x10 21.7-23.7 A 1030
Data applies to a density of 1 kg/dm3 and a kinematic viscosity of up to max. 20 mm2/sWarranty acc. to ISO 9906/A1) further starting modes on request2) Control cable: A = 1x8x1.5 ; Outside: 16.5--18.7 mm ; B = 1x10x1.5 ; Outside: 18.7--20.7 mm
Nr. : D2A / D2I[mm]
4 : 408 / 3783 : 398 / 3442 : 384 / 3171 : 367 / 295
H [m]
P [kW]
H [ft]
P [hp]
Kennlinien nachISO 9906/A
Curves as perISO 9906/A.
Courbes selonISO 9906/A.
FörderhöheHead
Hauteur
LeistungsbedarfPower Input
Puiss. hyd. abs.
Förderstrom/Rate of Flow/Débit
LaufradformImpeller type
Forme de roue
freier Durchgangfree passage
section de passage
145 x 135 mm
Amacan K
44
Amacan K 800-381 735 1/min
400 V 50 Hz 3~ (winding 400/690 V) max. temperature of liquid handled 30/40�C
Motor Motor Amacan K Code Irated Istarting 1) cos � Electric cables NSSHöu-J Weight
design rating 800-381/... Nr. d.o.l. Power supply cable Control
U or X P2 Cross-section Outsidedia.
cable
(Flameproof) kW A A mm2 mm kg
U 16 .../178 U 36.0 115 0.79 1x(7x4+5x1.5) 26.9-28.8 -- 630
tmax = 30 �C 20 .../218 U 44.0 150 0.75 1x(7x10+5x1.5) 29.5-32.9 -- 700
X 16 .../178 X 36.0 115 0.79 1x(7x4+5x1.5) 26.9-28.8 -- 630
tmax = 40 �C 20 .../218 X 44.0 150 0.75 1x(7x10+5x1.5) 29.5-32.9 -- 700
Data applies to a density of 1 kg/dm3 and a kinematic viscosity of up to max. 20 mm2/sWarranty acc. to ISO 9906/A1) further starting modes on request
H [m]
P [kW]
H [ft]
P [hp]
Kennlinien nachISO 9906/A
Curves as perISO 9906/A.
Courbes selonISO 9906/A.
FörderhöheHead
Hauteur
LeistungsbedarfPower Input
Puiss. hyd. abs.
Förderstrom/Rate of Flow/Débit
LaufradformImpeller type
Forme de roue
freier Durchgangfree passage
section de passage
126 x 100 mm
Nr. : D2A / D2I[mm]
6 : 450 / 4205 430 / 4004 : 420 / 3703 : 403 / 3492 : 387 / 3221 : 370 / 302
Amacan K
45
Amacan K 1000-420 980 1/min
400 V 50 Hz 3~ (winding 400/690 V) max. temperature of liquid handled 30/40�C
Motor Motor Amacan K Code Irated Istarting 1) cos � Electric cables NSSHöu-J Weight
design rating 1000-420/... Nr. d.o.l. Power supply cable Control
U or X P2 Cross-section Outsidedia.
cable 2)
(Flameproof) kW A A mm2 mm kg
45 .../456 U1 92.0 460 0.79 2x4x10 21.7--23.7 A 1050
U 64 .../646 U1 139.0 600 0.74 2x4x16 27.1--30.1 A 1200
tmax = 30 �C 80 .../806 U1 158.0 740 0.81 2x4x25 32.8--35.8 A 1400max
102 .../1026 U 200.0 1140 0.82 2x4x25 32.8--35.8 A 1550
45 .../646 X1 105.0 600 0.69 2x4x10 21.7--23.7 A 1200
X 64 .../806 X1 131.0 740 0.77 2x4x16 27.1--30.1 A 1400
tmax = 40 �C 80 .../1026 X 158.0 1140 0.80 2x4x25 32.8--35.8 A 1550max
102 .../1206 X 200.0 1450 0.79 2x4x25 32.8--35.8 A 1650
Data applies to a density of 1 kg/dm3 and a kinematic viscosity of up to max. 20 mm2/sWarranty acc. to ISO 9906/A1) further starting modes on request2) Control cable : A = 1x8x1.5 ; Outside: 16.5--18.7 mm ; B = 1x10x1.5 ; Outside: 18.7--20.7 mm
H [m]
P [kW]
H [ft]
P [hp]
Kennlinien nachISO 9906/A
Curves as perISO 9906/A.
Courbes selonISO 9906/A.
FörderhöheHead
Hauteur
LeistungsbedarfPower Input
Puiss. hyd. abs.
Förderstrom/Rate of Flow/Débit
LaufradformImpeller type
Forme de roue
freier Durchgangfree passage
section de passage
126 x 100 mm
Nr. : D2A / D2I[mm]
6 : 450 / 4205 430 / 4004 : 420 / 3703 : 403 / 3492 : 387 / 3221 : 370 / 302
Amacan K
46
Amacan K 1000-420 735 1/min
400 V 50 Hz 3~ (winding 400/690 V) max. temperature of liquid handled 30/40�C
Motor Motor Amacan K Code Irated Istarting 1) cos � Electric cables NSSHöu-J Weight
design rating 1000-420/... Nr. d.o.l. Power supply cable Control
U or X P2 Cross-section Outsidedia.
cable 2)
(Flameproof) kW A A mm2 mm kg
U25 .../258 U2 57.0 230 0.73 2x4x4 16.6--18.7 A 1000
U
t = 30 �C33 .../338 U2 72.0 300 0.75 2x4x6 17.8--19.8 A 1050
tmax = 30 �C 43 .../438 U 100.0 460 0.70 2x4x10 21.7--23.7 A 1150
X25 .../338 X2 59.0 300 0.70 2x4x4 16.6--18.7 A 1050
X
t = 40 �C33 .../438 X 85.0 460 0.64 2x4x10 21.7--23.7 A 1150
tmax = 40 �C 43 .../548 X 105.0 560 0.66 2x4x10 21.7--23.7 A 1200
Data applies to a density of 1 kg/dm3 and a kinematic viscosity of up to max. 20 mm2/sWarranty acc. to ISO 9906/A1) further starting modes on request2) Control cable : A = 1x8x1.5 ; Outside : 16.5--18.7 mm ; B = 1x10x1.5 ; Outside : 18.7--20.7 mm
H [m]
P [kW]
H [ft]
P [hp]
Kennlinien nachISO 9906/A
Curves as perISO 9906/A.
Courbes selonISO 9906/A.
FörderhöheHead
Hauteur
LeistungsbedarfPower Input
Puiss. hyd. abs.
Förderstrom/Rate of Flow/Débit
LaufradformImpeller type
Forme de roue
freier Durchgangfree passage
section de passage
140 x 150 mm
Nr. : D2A / D2I[mm]
4 : 450 / 4153 434 / 3862 : 416 / 3561 : 396 / 324
Amacan K
47
Amacan K 1000-421 980 1/min
400 V 50 Hz 3~ (winding 400/690 V) max. temperature of liquid handled 30/40�C
Motor Motor Amacan K Code Irated Istarting 1) cos � Electric cables NSSHöu-J Weight
design rating 1000-421/... Nr. d.o.l. Power supply cable Control
U or X P2 Cross-section Outsidedia.
cable 2)
(Flameproof) kW A A mm2 mm kg
37 .../376 U1 77.0 335 0.78 2x4x6 17.8--19.8 A 1010
U 45 .../456 U1 92.0 460 0.79 2x4x10 21.7--23.7 A 1050
tmax = 30 �C 64 .../646 U1 139.0 600 0.74 2x4x16 27.1--30.1 A 1200max
80 .../806 U1 158.0 740 0.81 2x4x25 32.8--35.8 A 1400
X37 .../456 X1 77.0 460 0.77 2x4x6 17.8--19.8 A 1050
X
t = 40 �C45 .../646 X1 105.0 600 0.69 2x4x10 21.7--23.7 A 1200
tmax = 40 �C 64 .../806 X1 131.0 740 0.77 2x4x16 27.1--30.1 A 1400
Data applies to a density of 1 kg/dm3 and a kinematic viscosity of up to max. 20 mm2/sWarranty acc. to ISO 9906/A1) further starting modes on request2) Control cable : A = 1x8x1.5 ; Outside : 16.5--18.7 mm ; B = 1x10x1.5 ; Outside : 18.7--20.7 mm
H [m]
P [kW]
H [ft]
P [hp]
Kennlinien nachISO 9906/A
Curves as perISO 9906/A.
Courbes selonISO 9906/A.
FörderhöheHead
Hauteur
LeistungsbedarfPower Input
Puiss. hyd. abs.
Förderstrom/Rate of Flow/Débit
LaufradformImpeller type
Forme de roue
freier Durchgangfree passage
section de passage
140 x 150 mm
Nr. : D2A / D2I[mm]
4 : 450 / 4153 434 / 3862 : 416 / 3561 : 396 / 324
Amacan K
48
Amacan K 1000-421 735 1/min
400 V 50 Hz 3~ (winding 400/690 V) max. temperature of liquid handled 30/40�C
Motor Motor Amacan K Code Irated Istarting 1) cos � Electric cables NSSHöu-J Weight
design rating 1000-421/... Nr. d.o.l. Power supply cable Control
U or X P2 Cross-section Outsidedia.
cable 2)
(Flameproof) kW A A mm2 mm kg
U25 .../258 U2 57.0 230 0.73 2x4x4 16.6--18.7 A 1000
U
t = 30 �C33 .../338 U2 72.0 300 0.75 2x4x6 17.8--19.8 A 1050
tmax = 30 �C 43 .../438 U 100.0 460 0.70 2x4x10 21.7--23.7 A 1150
19 .../258 X2 46.0 230 0.68 2x4x4 16.6--18.7 A 1000
X 25 .../338 X2 59.0 300 0.70 2x4x4 16.6--18.7 A 1050
tmax = 40 �C 33 .../438 X 85.0 460 0.64 2x4x10 21.7--23.7 A 1150max
43 .../548 X 105.0 560 0.66 2x4x10 21.7--23.7 A 1200
Data applies to a density of 1 kg/dm3 and a kinematic viscosity of up to max. 20 mm2/sWarranty acc. to ISO 9906/A1) further starting modes on request2) Control cable : A = 1x8x1.5 ; Outside : 16.5--18.7 mm ; B = 1x10x1.5 ; Outside : 18.7--20.7 mm
H [m]
P [kW]
H [ft]
P [hp]
Kennlinien nachISO 9906/A
Curves as perISO 9906/A.
Courbes selonISO 9906/A.
FörderhöheHead
Hauteur
LeistungsbedarfPower Input
Puiss. hyd. abs.
Förderstrom/Rate of Flow/Débit
LaufradformImpeller type
Forme de roue
freier Durchgangfree passage
section de passage
145 x 110 mmNr. : D2A / D2I
[mm]4 : 508 / 5083 460 / 4602 : 448 / 4121 : 430 / 350
Amacan K
49
Amacan K 1000-500 (applies to Amacan K 1300-500, too) 980 1/min
400 V 50 Hz 3~ (winding 400/690 V) max. temperature of liquid handled 30/40�C
Motor Motor Amacan K Code Irated Istarting 1) cos � Electric cables NSSHöu-J Weight
design rating 1000-500/... Nr. d.o.l. Power supply cable Control
U or X P2 Cross-section Outsidedia.
cable 2)
(Flameproof) kW A A mm2 mm kg
80 .../806 U1 158.0 740 0.81 2x4x25 32.8--35.8 A 1470
102 .../1026 U 200.0 1140 0.82 2x4x25 32.8--35.8 A 1630
U 120 .../1206 U 230.0 1450 0.82 2x4x35 36.9--39.9 A 1750
tmax = 30 �C 138 .../1386 U 245.0 1750 0.87 2x4x35 36.9--39.9 B 2050tmax 30 C165 .../1656 U 285.0 1670 0.89 2x4x50 42.9--45.9 B 2200
200 .../2006 U 345.0 2400 0.91 2x3x70/35 48.4--51.4 B 2350
80 .../1026 X 158.0 1140 0.80 2x4x25 32.8--35.8 A 1630
X102 .../1206 X 200.0 1450 0.80 2x4x25 32.8--35.8 A 1750
X
t = 40 �C120 .../1386 X 215.0 1750 0.87 2x4x35 36.9--39.9 B 2050
tmax = 40 �C 138 .../1656 X 240.0 1670 0.89 2x4x35 36.9--39.9 B 2200
165 .../2006 X 258.0 2400 0.90 2x4x50 42.9--45.9 B 2350
Data applies to a density of 1 kg/dm3 and a kinematic viscosity of up to max. 20 mm2/sWarranty acc. to ISO 9906/A1) further starting modes on request2) Control cable : A = 1x8x1.5 ; Outside: 16.5--18.7 mm ; B = 1x10x1.5 ; Outside: 18.7--20.7 mm
H [m]
P [kW]
H [ft]
P [hp]
Kennlinien nachISO 9906/A
Curves as perISO 9906/A.
Courbes selonISO 9906/A.
FörderhöheHead
Hauteur
LeistungsbedarfPower Input
Puiss. hyd. abs.
Förderstrom/Rate of Flow/Débit
LaufradformImpeller type
Forme de roue
freier Durchgangfree passage
section de passage
133 x 150 mm
Nr. : D2A / D2I[mm]
5 : 582 / 5504 : 565 / 5173 : 550 / 4742 : 540 / 4421 : 520 / 380
Amacan K
50
Amacan K 1200-540 (applies to Amacan k 1300-540 and 1400-540, too) 980 1/min
400 V 50 Hz 3~ (winding 400/690 V) max. temperature of liquid handled 30/40�C
Motor Motor Amacan K Code Irated Istarting 1) cos � Electric cables NSSHöu-J Weight
design rating 1200-540/... Nr. d.o.l. Power supply cable Control
U or X P2 Cross-section Outsidedia.
cable 2)
(Flameproof) kW A A mm2 mm kg
165 .../1656 U 285.0 1670 0.89 2x4x50 42.9--45.9 B 3000
U 200 .../2006 U 345.0 2400 0.91 2x3x70/35 48.4--51.4 B 3150
tmax = 30 �C 260 .../2606 U 450.0 1920 0.89 2x3x95/50 55.0--59.0 B 3550max
320 .../3206 U 590.0 3700 0.83 4x4x50 42.9--45.9 B 3750
X165 .../2006 X 285.0 2400 0.90 2x4x50 42.9--45.9 B 3150
X
t = 40 �C200 .../2606 X 345.0 1920 0.88 2x3x70/35 48.4--51.4 B 3550
tmax = 40 �C 260 .../3206 X 470.0 3700 0.84 4x4x35 36.9--39.9 B 3750
Data applies to a density of 1 kg/dm3 and a kinematic viscosity of up to max. 20 mm2/sWarranty acc. to ISO 9906/A1) further starting modes on request2) Control cable: A = 1x8x1.5 ; Outside: 16.5--18.7 mm ; B = 1x10x1.5 ; Outside: 18.7--20.7 mm
H [m]
P [kW]
H [ft]
P [hp]
Kennlinien nachISO 9906/A
Curves as perISO 9906/A.
Courbes selonISO 9906/A.
FörderhöheHead
Hauteur
LeistungsbedarfPower Input
Puiss. hyd. abs.
Förderstrom/Rate of Flow/Débit
LaufradformImpeller type
Forme de roue
freier Durchgangfree passage
section de passage
133 x 150 mm
Nr. : D2A / D2I[mm]
5 : 582 / 5504 : 565 / 5173 : 550 / 4742 : 540 / 4421 : 520 / 380
Amacan K
51
Amacan K 1200-540 (applies to Amacan K 1300-540, too) 735 1/min
400 V 50 Hz 3~ (winding 400/690 V) max. temperature of liquid handled 30/40�C
Motor Motor Amacan K Code Irated Istarting 1) cos � Electric cables NSSHöu-J Weight
design rating 1200-540/... Nr. d.o.l. Power supply cable Control
U or X P2 Cross-section Outsidedia.
cable 2)
(Flameproof) kW A A mm2 mm kg
84 .../848 U 177.0 680 0.77 2x4x25 32.8--35.8 A 2400
U 107 .../1078 U2 225.0 1000 0.76 2x4x35 36.9--39.9 A 2500
tmax = 30 �C 126 .../1268 U2 240.0 1220 0.83 2x4x35 36.9--39.9 B 2910max
150 .../1508 U2 285.0 1400 0.82 2x4x50 42.9--45.9 B 3100
84 .../1078 X2 199.0 1000 0.67 2x4x25 32.8--35.8 A 2500
X 107 .../1268 X2 205 1220 0.82 2x4x35 36.9--39.9 B 2910
tmax = 40 �C 126 .../1508 X2 250.0 1400 0.80 2x4x50 42.9--45.9 B 3100max
150 .../1808 X2 275.0 1700 0.85 2x4x50 42.9--45.9 B 3210
Data applies to a density of 1 kg/dm3 and a kinematic viscosity of up to max. 20 mm2/sWarranty acc. to ISO 9906/A1) further starting modes on request2) Control cable : A = 1x8x1.5 ; Outside: 16.5--18.7 mm ; B = 1x10x1.5 ; Outside: 18.7--20.7 mm
H [m]
P [kW]
H [ft]
P [hp]
Kennlinien nachISO 9906/A
Curves as perISO 9906/A.
Courbes selonISO 9906/A.
FörderhöheHead
Hauteur
LeistungsbedarfPower Input
Puiss. hyd. abs.
Förderstrom/Rate of Flow/Débit
LaufradformImpeller type
Forme de roue
freier Durchgangfree passage
section de passage
133 x 150 mm
Nr. : D2A / D2I[mm]
5 : 582 / 5504 : 565 / 5173 : 550 / 4742 : 540 / 4421 : 520 / 380
Amacan K
52
Amacan K 1200-540 590 1/min
400 V 50 Hz 3~ (winding 400/690 V) max. temperature of liquid handled 30/40�C
Motor Motor Amacan K Code Irated Istarting 1) cos � Electric cables NSSHöu-J Weight
design rating 1200-540/... Nr. d.o.l. Power supply cable Control
U or X P2 Cross-section Outsidedia.
cable 2)
(Flameproof) kW A A mm2 mm kg
43 .../4310 U1 99.0 380 0.68 2x4x10 21.7--23.7 A 2250
U 54 .../5410 U2 121.0 420 0.71 2x4x16 27.1--30.1 A 2350
tmax = 30 �C 67 .../6710 U2 149.0 540 0.71 2x4x16 27.1--30.1 A 2450max
84 .../8410 U2 189.0 680 0.70 2x4x25 32.8--35.8 A 2550
43 .../5410 X2 102.0 420 0.67 2x4x10 21.7--23.7 A 2350
X 54 .../6710 X2 125.0 540 0.68 2x4x16 27.1--30.1 A 2450
tmax = 40 �C 67 .../8410 X2 159.0 680 0.66 2x4x25 32.8--35.8 A 2550max
84 .../10710 X2 185.0 980 0.70 2x4x25 32.8--35.8 B 2900
Data applies to a density of 1 kg/dm3 and a kinematic viscosity of up to max. 20 mm2/sWarranty acc. to ISO 9906/A1) further starting modes on request2) Control cable: A = 1x8x1.5 ; Outside : 16.5--18.7 mm ; B = 1x10x1.5 ; Outside : 18.7--20.7 mm
H [m]
P [kW]
H [ft]
P [hp]
Kennlinien nachISO 9906/A
Curves as perISO 9906/A.
Courbes selonISO 9906/A.
FörderhöheHead
Hauteur
LeistungsbedarfPower Input
Puiss. hyd. abs.
Förderstrom/Rate of Flow/Débit
LaufradformImpeller type
Forme de roue
freier Durchgangfree passage
section de passage
145 mm
Nr. : D2A / D2I[mm]
5 : 612 / 5324 : 600 / 5053 : 585 / 4872 : 570 / 4601 : 560 / 435
Amacan K
53
Amacan K 1300-520 (applies to Amacan K 1400-520, too) 735 1/min
400 V 50 Hz 3~ (winding 400/690 V) max. temperature of liquid handled 30/40�C
Motor Motor Amacan K Code Irated Istarting 1) cos � Electric cables NSSHöu-J Weight
design rating 1300-520/... Nr. d.o.l. Power supply cable Control
U or X P2 Cross-section Outsidedia.
cable 2)
(Flameproof) kW A A mm2 mm kg
126 .../1268 U1 235 1220 0.84 2x4x35 36.9--39.9 B 3050
U 150 .../1508 U1 290 1400 0.82 2x4x50 42.9--45.9 B 3200U
tmax = 30 �C 180 .../1808 U1 335 1700 0.84 2x3x70/35 48.4--51.4 B 3350max
225 .../2258 U1 425 2650 0.83 2x3x95/50 55.0--59.0 B 3900
126 .../1508 X1 245 1400 0.81 2x4x35 36.9--39.9 B 3200
X 150 .../1808 X1 275 1700 0.85 2x4x50 42.9--45.9 B 3350
tmax = 40 �C 180 .../2258 X1 355 2650 0.80 2x3x70/35 48.4--51.4 B 3900max
225 .../2808 X1 445 3420 0.78 2x3x95/50 55.0--59.0 B 4250
Data applies to a density of 1 kg/dm3 and a kinematic viscosity of up to max. 20 mm2/sWarranty acc. to ISO 9906/A1) further starting modes on request2) Control cable: A = 1x8x1.5 ; Outside: 16.5--18.7 mm ; B = 1x10x1.5 ; Outside: 18.7--20.7 mm
H [m]
P [kW]
H [ft]
P [hp]
Kennlinien nachISO 9906/A
Curves as perISO 9906/A.
Courbes selonISO 9906/A.
FörderhöheHead
Hauteur
LeistungsbedarfPower Input
Puiss. hyd. abs.
Förderstrom/Rate of Flow/Débit
LaufradformImpeller type
Forme de roue
freier Durchgangfree passage
section de passage
145 mm
Nr. : D2A / D2I[mm]
5 : 612 / 5324 : 600 / 5053 : 585 / 4872 : 570 / 4601 : 560 / 435
Amacan K
54
Amacan K 1300-520 590 1/min
400 V 50 Hz 3~ (winding 400/690 V) max. temperature of liquid handled 30/40�C
Motor Motor Amacan K Code Irated Istarting 1) cos � Electric cables NSSHöu-J Weight
design rating 1300-520/... Nr. d.o.l. Power supply cable Control
U or X P2 Cross-section Outsidedia.
cable 2)
(Flameproof) kW A A mm2 mm kg
U67 .../6710 U1 149 540 0.71 2x4x16 27.1--30.1 A 2650
U
t = 30 �C84 .../8410 U1 189 680 0.70 2x4x25 32.8--35.8 A 2750
tmax = 30 �C 107 .../10710 U1 220 980 0.75 2x4x35 36.9--39.9 B 3000
X67 .../8410 X2 159 680 0.66 2x4x25 32.8--35.8 A 2750
X
t = 40 �C84 .../10710 X2 185 980 0.70 2x4x25 36.9--39.9 B 3000
tmax = 40 �C 107 .../12610 X2 205 1070 0.82 2x4x35 36.9--39.9 B 3200
Data applies to a density of 1 kg/dm3 and a kinematic viscosity of up to max. 20 mm2/sWarranty acc. to ISO 9906/A1) further starting modes on request2) Control cable: A = 1x8x1.5 ; Outside: 16.5--18.7 mm ; B = 1x10x1.5 ; Outside: 18.7--20.7 mm
Amacan K
55
Hydraulic data of pump sizes -- 1300--750on request
L
suspension at the cover or with BU / BG / Aat a support
L = mm
lower edge of pit = lower edge of pump
1579.5/3--10
10/97
Subjecttomodificationwithoutnotice
KSB AktiengesellschaftP.O. Box 200743 � 06008 Halle (Saale) � Turmstraße 92 � 06110 Halle (Germany)Tel. +49 (345) 48 26 0 � Fax +49 (345) 48 26 46 99 � www.ksb.com
Amacan K
Order detail -- carrier cable lengthIn order to select the proper length of the carrier cable, it is absolutely necessary to define dimension ”L”.
top related