technical course technical course - bikesportz imports · technical course technical course ......
Post on 19-Jul-2018
304 Views
Preview:
TRANSCRIPT
1
Technical course
Technical course
Campagnolo Training Center
REV.06
Programme
2
1
2
5
4
3
The EPS and its operation
Installation
Diagnostics
Spare parts and warranty6
Maintenance
Adjustments after installation
2
Campagnolo Training Center
REV.06
Important information
3
The EPS system
The product
Danger: if care is not taken injury to personnel and to those nearby may occur
Information and agreements
Section Chapter
Campagnolo Training Center
REV.06
ascend
4
Definitions used in this presentation
ascend descend
descend
1st11th
3
Campagnolo Training Center
REV.06 5
12
4
3
5
The EPS and its operation
• The product• Operation on the road• System components• Customer adjustments
6
Campagnolo Training Center
REV.06
EPS, Electronic Power Shift, is the 11 speedelectronic rear derailleur system conceived, builtand marketed by Campagnolo.
2 versions are available:
6
The EPS system
The product
4
Campagnolo Training Center
REV.06
The requests that the cyclist makes through the levers of the two controllers located on the handlebar are received by the electronic system. This system, with some optimisations, implements the requests, activating the rear and front derailleurs through electric motors.
Simultaneously the electronic system verifies that the rear and front derailleurs move correctly and reaches the required position.
The system also carries out other functions which we will discuss later.
7
The EPS system
Operation on the road
Campagnolo Training Center
REV.06
The control levers of the EPS system are positioned and act with the same logic as mechanical Campagnolo system levers.Lever 1 brake
Lever 2 lever near the brake
Lever 3 internal lever
8
The EPS system
Operation on the road
3
1
2
5
Campagnolo Training Center
REV.06
Right control
Lever 2
9
The EPS system
Operation on the road
Campagnolo Training Center
REV.06
Right control
Lever 3
10
The EPS system
Operation on the road
6
Campagnolo Training Center
REV.06
Right control
By holding down levers 2 or 3 we obtain a continuous movement of the rear derailleur in ascent or descent.
11
The EPS system
Operation on the road
Campagnolo Training Center
REV.06
Left control
Lever 2
12
The EPS system
Operation on the road
7
Campagnolo Training Center
REV.06 13
The EPS system
Operation on the road
Left control
Lever 3
Campagnolo Training Center
REV.06
Depending on the sprocket selected, the EPS automatically repositions the front derailleur to optimise its position with respect to the chain and prevent rubbing.
This allows crossovers of the chain that are not ideal in traditional systems.
Both in ascent and descent, 2 corrections are carried out.
14
The EPS system
Operation on the road
Automatic correction of the front derailleurExample of a correction
8
Campagnolo Training Center
REV.06
In order to aid the front derailleur in ascent, in the event of a large chain crossover, the front derailleur carries out anover‐run with respect to the expected movement and, after a moment, assumes it’s correct position. The overrun is proportional to the sprocket used and cannot be adjusted by the user.
15
The EPS system
Operation on the road
The front derailleur over‐run
Campagnolo Training Center
REV.06
In case of large chain crossover, but with a front derailleur shifting to the small chainring, the front derailleur does NOT carry out an overrun as it may seem, but carries out the normal run and, immediately afterward, carries out a correctionpreviously described.
16
The EPS system
Operation on the road Front derailleur in descent with high chain crossover
9
Campagnolo Training Center
REV.06
The system also carries out a rear derailleur over‐run in case of descent and ascent on the first 5° sprockets
17
The EPS system
Operation on the road
Example of descent to the 4th sprocket
The rear derailleur over‐run
Campagnolo Training Center
REV.06
Other advantages of the EPS system are:greater positioning precision (max error of 0.05 mm thanks to the electric motor’s position resolver) compared to a mechanical rear derailleur ‐ in whichprecision is tied to the cable movement and the returnspring in the derailleur.constant front and rear derailleur action speed, by eliminating cable frictionsoft action and limited run of the leverspossibility of braking and changing gearssimultaneouslythe design of the frame is no longer dictated by the need for simple cable runs
18
The EPS system
Operation on the road
10
Campagnolo Training Center
REV.06
The EPS system, unlike traditional systems, is made up of 6 main components, 2 of which are completely new:
right rear derailleur controlleft front derailleur controlinterfacepower unitfront derailleurrear derailleur
Each of these components has one or more cables for properinterconnection.
A battery charger is also provided in order to recharge the batteries as well asa magnet to switch off the system.
19
System components
The EPS system
Campagnolo Training Center
REV.06 20
System components
The EPS system
11
Campagnolo Training Center
REV.06 21
System components
The EPS system
Campagnolo Training Center
REV.06
Right control lever 1 brakelever 2 command to “ascend” to the largest sprocketlever 3 command to “descend” to the smallest sprocketMODE button: short‐press this button to view the battery charge state
22
System components
The EPS system
MODE
12
Campagnolo Training Center
REV.06
Left controllever 1 brakelever 2 command to “ascend” to the largest chain ringlever 3 command to “descend” to the smallest chain ringMODE button: short‐press this button to view the battery charge state
23
System components
The EPS system
MODE
Campagnolo Training Center
REV.06
Interface
Its main functions are:
To activate the various coloured LEDs in order to communicate with the user
To receive the command actions
To dialogue, thanks to a digital line, with the power unit
24
System components
The EPS system
13
Campagnolo Training Center
REV.06 25
FIXED GREEN LEDFrom 100 % to 60 % charge
FLASHING GREEN LEDFrom 60 % to 40 % charge
FIXED YELLOW LEDFrom 40 % to 20 % charge
FIXED RED LEDFrom 20 % to 6 % charge
FLASHING RED LED + ACOUSTIC ALARM (BUZZER)From 6 % to 0 % charge (with decreasing frequency of automatic indication)
The battery charge level can be verified by short pressing one of the two Mode buttons
Verification of the battery charge state
The EPS system
Campagnolo Training Center
REV.06
Power system
Its main functions are:
Contains and manages the battery pack
Activates and controls the rearderailleur and the front derailleur
Indicates any faults with the LEDDialogues, thanks to a digitalline, with the interface
Activates the buzzer
26
System components
The EPS system
14
Campagnolo Training Center
REV.06
So ‐ EPS is an electronic system, controlled by a number of electronic components, that communicate and manage the drive train to obtain the best performance.
27
System components
Il sistema EPS
Campagnolo Training Center
REV.06 28
Il sistema EPS
Example of electric circuit(electro‐mechanic system)
EPS: electronic system
Interface
Powersystem
I = VxR
…11100101101..
…110101..
System components
15
Campagnolo Training Center
REV.06
Average duration of the battery for use on the road:
•average of 500 km/month: 1500 km
•average of 1000 km/month: 1800 km
•average of 2000 km/month: 2000 km
Range in km with 0‐6% charge is variable depending on the outdoor temperature and conditions of use
Battery charge times from a charge of 0‐6 % to 100%: about 4 hours
29
System components
The EPS system
Campagnolo Training Center
REV.06
The rear derailleur
Is made up of:
Mechanical structure
Electric motor with resolver
Mechanical limit switchadjustment screw
Adjustment screw for the distance between the pulleyand the sprocket cassette
30
System components
The EPS system
16
Campagnolo Training Center
REV.06 31
System components
The EPS system
The front derailleur
Is made up of:
Mechanical structure with cage
Electric motor with resolver
Campagnolo Training Center
REV.06
In case of assembly/disassembly or maintenance of the components, the EPS must be switched off by inserting the magnet in its lodging on the lower part of the power unit.
32
System components
The EPS system
In case of transportation of the bicycle leaving the system in stand‐by is recommended (do NOT insert the magnet) because, in the event the rear or front derailleur should be accidentally moved, the system will not lose the reference point for its proper position.
The shut‐off magnet
17
Campagnolo Training Center
REV.06
There are 2 LEDs on the power supply unit which perform the following functions:
•on in the presence of mains power
•on while the battery is being charged; once the battery is fully charged, this LED turns off.
33
System components
The EPS system
The battery charger
Campagnolo Training Center
REV.06
The battery charger is compatible with:
•110‐220V voltage and 50‐60 Hz frequency
•12 V voltage for car recharging (optional cable)
34
System components
The EPS system
Do not use a battery charger other than the oneprovided with the EPS system
The battery charger
18
Campagnolo Training Center
REV.06
The battery charger
While recharging the interface displays the battery charge state while the rear and front derailleur motors are deactivated.
In this state, even if the magnet is inserted to switch off the system, the battery charge procedure will not be interrupted.
35
System components
The EPS system
Campagnolo Training Center
REV.06
The MODE buttons, besides verifying the batterycharge state, allow the user to
carry out adjustments to the rear and front derailleur which correspond to the adjustmentscarried out with the cable adjusters in traditional systems
cancel any temporary malfunctions detectedby the system and indicated by the LED on the power unit (please see the Diagnostics Chapter)
36
Customer adjustments
The EPS system
19
Campagnolo Training Center
REV.06
Adjustment of the rear and front derailleursThe customer can adjust the reference position of the rear and/or front derailleur through the adjustment procedure. Adjustment of the rear derailleur is done mainly in the event of a wheel change. This might be required if the wheel that is fitted has the casette positioned differently relative to the rear drop‐out.In the case of adjustments of the rear and front derailleur, we can position the chain on whichever chainring we wish.With each pressing of buttons 2 or 3, the system carries out a fixed movement of about 0. 25 mm if we act on the rear derailleur, and about 0.1 mm if we act on the front derailleur.
37
Customer adjustments
The EPS system
Campagnolo Training Center
REV.06
Adjustment of the rear and front derailleursOnce adjustment is completed, the system will implement a change to the positions established for all of the sprockets (or chainrings) with a correction equal to that reset with the adjustment.For example, if the distance of the first 3 index points from the drop‐out is: 12.40 ‐ 16.60 ‐ 20.4 mmafter a correction of about 0.25 mm with lever 3 toward the drop‐out, the new positions which the rear derailleur assumes will be about:12.15 – 16.35 – 20.15 mm …
38
The EPS system
Customer adjustments
20
Campagnolo Training Center
REV.06
Adjustment of the rear and front derailleurs
Remember that the chain is perfectly centred, for the sprockets from the 3rd to the 10th, with about 3 movements in descent the chain approaches the lower sprocket and with 3 movements in ascent it approaches the upper sprocket.
39
The EPS system
Customer adjustments
Campagnolo Training Center
REV.06
Adjustment of the rear and front derailleurs
40
The EPS system
Customer adjustments
Note that any adjustment carried out whilst in motion may cause a danger of injury to the cyclist or others: proceed with extreme caution if you decide to carry out the adjustment anyway.
21
Campagnolo Training Center
REV.06
Adjustment of the rear derailleur
press the right MODE button for about 6 seconds
adjust the position by pressing buttons 2 and/or 3
short‐press the right MODE button to store the adjustment
41
A
The EPS system
Customer adjustments
Campagnolo Training Center
REV.06
Adjustment of the front derailleur
press the left MODE button for about 6 seconds
adjust the position by pressing buttons 2 and/or 3
short‐press the left MODE button to store the adjustment
42
The EPS system
Customer adjustments
22
Campagnolo Training Center
REV.06
Failure to conclude the adjustmentIf the MODE button is not short‐pressed to conclude the adjustment procedure, after a predetermined time of about 48sec, the system automatically exits the adjustment procedure and the new adjustment is stored.
43
The EPS system
Customer adjustments
Contemporary adjustment of front and rear derailleurWhen you press one of the two MODE button, right or left, it’spossible to do the adjustment of the front or rear derailleur.
The memorization can be done with one of the 2 MODE buttons.
Campagnolo Training Center
REV.06
In some case of rear wheel replacement, if the cassette of the new wheel is very different from the previously installed one, it may be more adviseable to carry out a more precise adjustment by performing a full reset of the rear derailleur.
44
Rear derailleur reset procedure
The EPS system
Customer adjustments
23
Campagnolo Training Center
REV.06
This procedure allows the system to learn the positions of the chain on the 2nd and 10th sprockets, from which it can then calculate the positions of the other sprockets.
During the reset procedure movements of the rear derailleur take place continuously, and not with fixed incriments as during adjustment, depending on the time that rear derailleur levers 2 and 3 are held in.
It is possible to very accurately modify the position, by just a few hundredths of a millimetre.
45
The EPS system
Rear derailleur reset procedure
Customer adjustments
Campagnolo Training Center
REV.06
1. Position the rear derailleur on the 11°sprocket and on the large chainring
46
The EPS system
Rear derailleur reset procedure
24
Campagnolo Training Center
REV.06
2. simultaneously press the two MODE buttons until the blue LED turns on (about 6 seconds)
47
The EPS system
Rear derailleur reset procedure
Customer adjustments
Campagnolo Training Center
REV.06
3. position the rear derailleur on the 2nd sprocket
4. adjust the position by pressing buttons 2 and/or 3
48
The EPS system
Rear derailleur reset procedure
Customer adjustments
25
Campagnolo Training Center
REV.06
5. press the right MODE button to store the position of the 2nd sprocket
6. position the rear derailleur on the 10th sprocket
49
The EPS system
Rear derailleur reset procedure
Customer adjustments
Campagnolo Training Center
REV.06
7. adjust the position by pressing buttons 2 and/or 3
8. short‐press the right MODE button to store the position of the 10th sprocket and to conclude the procedure.
50
The EPS system
Rear derailleur reset procedure
Customer adjustments
26
Campagnolo Training Center
REV.06 51
2
1
4
3
5
Installation • Workshop tools• Interface with the frame• Compatibility• Preparation of the frame and
components• Cable run and installation6
Campagnolo Training Center
REV.06
The specific tools, available for the operators(S.C., OEM, Pro Shop), for installation of the EPS system are:
•Cable run magnet kit
52
Installation
Workshop tools
27
Campagnolo Training Center
REV.06
• Connector disconnection tool
53
Installation
Workshop tools
Campagnolo Training Center
REV.06
The generic tools for the EPS system are:
54
Installation
Workshop tools
Tool code or size used for
Chain tool UT‐CN300 chain
Torque wrench 20‐100 Nm BB axle, BB cups
BB cups tool (for torque wrench) UT‐BB130 BB cups
Allen wrench UT‐BB110 BB
Torque wrench 0 ‐ 20 Nm ergopower, rear gear, f. deraill.clamp on
Allen wrench (for torque wrench) 5 ergopower, rear gear, f. deraill.clamp on
Torx wrench (for torque wrench) T25 rear derailler
Caliper frame
Allen wrench 2‐3‐4‐5‐6 various
Torx wrench T25 rear derailler
Philips screwdriver 1,5 ergopower cover
Philips screwdriver medium
Screwdriver medium
Wrench 7 front derailler
Cutter housing
Pliers flat tips various
Derailleur Hanger Alignment Gauge to check the drop out
Bottom Bracket Tapping & Facing Set frame
Thickness gauge chain position
28
Campagnolo Training Center
REV.06
The EPS system is compatible with the following threaded bottom bracket shells and cups
55
Installation
Interface with the frame
TYPE X
Italian thread From 69.2 to 70.8
English thread From 67.2 to 68.8
Campagnolo Training Center
REV.06
In case of frames with bottom bracket cups Press Fit 86.5 x41 the following measurements have to be observed
56
Installation
Interface with the frame
29
Campagnolo Training Center
REV.06
In case of frames with Press Fit BB30 68 X 42bottom bracket cups the following measurements have to be observed
57
Installation
Interface with the frame
Campagnolo Training Center
REV.06 58
Installation
In case of frames with Press Fit BB30 68 X 46bottom bracket cups the following measurements have to be observed
Interface with the frame
30
Campagnolo Training Center
REV.06 59
Installation
Braze‐on version
Interface with the frame
Campagnolo Training Center
REV.06 60
Installation
QUOTA L
CENTRATURA
ATTACCO A
SALDARE
INGRANAGGI COMPATIBILI
138 48T 45T,46T,47T,48T,49T,50T,51T
140 49T 46T,47T,48T,49T,50T,51T,52T
142 50T 47T,48T,49T,50T,51T,52T,53T
144 51T 48T,49T,50T,51T,52T,53T,54T
146 52T 49T,50T,51T,52T,53T,54T,55T
148 53T 50T,51T,52T,53T,54T,55T,56T
150 54T 51T,52T,53T,54T,55T,56T
152 55T 52T,53T,54T,55T,56T
Braze‐on version (other than mechanical front derailleur)
Interface with the frame
31
Campagnolo Training Center
REV.06 61
Installation
Clamp‐on versionA new clamp was created for frames with 35 mm tube diameter. The clamp also replaces the current clamp for non EPS units.For 32 mm frames use the current clamp.
Interface with the frame
Use Campagnolo clamp only (code R1134888 for 35 mm tube)
Campagnolo Training Center
REV.06 62
Installation
Rear derailleur
L = 405 mm min
Interface with the frame
32
Campagnolo Training Center
REV.06 63
Il montaggio
Rear derailler
|LA-LB| & |LC-LD|6 mm
The tool must be positioned on vertical position (LA & LB) and on horizontal position: if the measurements are out of tolerance, use the tool to set the rear derailler hanger
Interface with the frame
Campagnolo Training Center
REV.06 64
Installation
Rear derailleur
Interface with the frame
33
Campagnolo Training Center
REV.06 65
Installation
Rear derailleur
B = 30 mm
Interface with the frame
Campagnolo Training Center
REV.06
The diameter of the holes and their positions have to conform to the measurements indicated here (note that the connector has a diameter of 7 mm)
66
Installation
Interface with the frame
34
Campagnolo Training Center
REV.06 67
Il montaggio
Interface with the frame
Campagnolo Training Center
REV.06 68
Il montaggio
Interface with the frame
M4
M5
M2,5
35
Campagnolo Training Center
REV.06 69
Installation
Interface with the frame
Campagnolo Training Center
REV.06
The compatible cranksets are:
53‐39, 52‐39 (Standard),
50‐34 (Compact EVO),
55‐42, 54‐42 (Individual Time Trial),
52‐36 (New 2013).
The 11 V compatible cassettes are:
11‐23, 11‐25, 12‐25, 12‐27, 12‐29
70
Installation
Compatibility
36
Campagnolo Training Center
REV.06
For complete functionality of the EPS system the dimensions of the compatible chainrings or sprockets cannot be changed.
71
Installation
Compatibility
Campagnolo Training Center
REV.06 72
Installation
Preparation of the frame and components
Because the presence of impurities, dirt or even worse, liquids, must be avoided during assembly of the electrical connectors, it is important that installation of the EPS system is carried out with clean hands, in a clean environment and not carried out whilst exposed to inclement weather in order to avoid the presence of dust, grease, water, etc. during installation.
37
Campagnolo Training Center
REV.06
Before installation, where possible, remember to mill the bottom bracket shell with the bottom braket facing tool in order to have:
•the two surfaces faced
•the correct chain line: 43,5 mm
Verify that the frame is free of any possible obstructions internally (i.e. bags from the production of carbon frames...)
73
Installation
Preparation of the frame and components
Campagnolo Training Center
REV.06
It’s important to chase the thread of the rear derailler hanger to install correctly the rear derailler.
Verify that the frame is free of any possible obstructions internally (i.e. bags from the production of carbon frames ...)
74
Installation
Preparation of the frame and components
38
Campagnolo Training Center
REV.06
Power system: install bracket for water‐bottle fixing or for lower position on the frame and verify the presence of the magnet
75
Installation
Preparation of the frame and components
Campagnolo Training Center
REV.06 76
Il montaggio
70 cm
55 cm 55 cm
55 cm
50 cm85 cm
Component connectors
Each pair of connectors is marked by differently coloured cable ties near the connectors.
Preparation of the frame and components
39
Campagnolo Training Center
REV.06
Component connectors
Each pair has polarized slots in order to make incorrect installation impossible (Poka‐yoke).
77
Installation
Preparation of the frame and components
Example of slots
Campagnolo Training Center
REV.06
Component connectors
In order to facilitate installation, each connector has an arrow for alignment with the respective counterpart.
78
Installation
Preparation of the frame and components
40
Campagnolo Training Center
REV.06
Component connectors
In a well lit area, before installation on the frame, highlighting the arrow with a white marker is recommended.
79
Installation
Preparation of the frame and components
Campagnolo Training Center
REV.06 80
Installation
Cable run and installationCable connection diagram
41
Campagnolo Training Center
REV.06 81
Installation
Cable run and installation
Control front derailleur
interface
Powersystem
Front derailleur
Rear derailleur
Control rear derailleur
yellow
green
red
blue violet
Cable connection diagram
Campagnolo Training Center
REV.06 82
Installation
Control front derailleur
interface
Powersystem
Front derailleur
Rear derailleur
Control rear derailleur
green
blue violet
Cable run and installationCable run for rear derailleur
42
Campagnolo Training Center
REV.06
Temporarily install the power unit
83
Installation
Cable run and installation
Campagnolo Training Center
REV.06
Running the rear derailleur connection cable
84
Installation
Cable run and installation
43
Campagnolo Training Center
REV.06 85
Installation
Control front derailleur
interface
Powersystem
Front derailleur
Rear derailleur
Control rear derailleur
green
red
blue violet
Cable run and connection to the interface Cable run and installation
Campagnolo Training Center
REV.06
Cable run and connection to the interface
86
Installation
Cable run and installation
44
Campagnolo Training Center
REV.06 87
Installation
Controlfront derailleur
interface
Powersystem
Front derailleur
Rear derailleur
Control rear derailleur
yellow
green
red
blue violet
Running the rear derailleur connection cable Cable run and installation
Campagnolo Training Center
REV.06
Running the rear derailleur connection cable
88
Installation
Cable run and installation
45
Campagnolo Training Center
REV.06
Installation of the controls on the handlebar
89
Installation
Cable run and installation
Tightening torque 10 Nm
Campagnolo Training Center
REV.06
Installation of the power unit
90
Installation
Cable run and installation
Installation of vibration damping rubber washer
46
Campagnolo Training Center
REV.06
Installation of the rear derailleur
91
Installation
Cable run and installation
Tightening torque: 15 Nm (Torx wrench T25)
Campagnolo Training Center
REV.06
Do not let the front derailleur cable slide back into the frame ‐anchor it with adhesive tape
92
Installation
Cable run and installation
47
Campagnolo Training Center
REV.06
Installation of the crankset
93
Installation
Cable run and installation
Be careful with the rear derailleur cable run
Campagnolo Training Center
REV.06 94
I ricambi e la garanzia
R 1137097: BB cable guide
Example of BB cable guide with Press Fit cups
Cable run and installation
48
Campagnolo Training Center
REV.06
Insert the BB cable guide cover cylinder from the bevelled side to ease insertion despite the presence of the rear derailleur cable
95
Installation
Cable run and installation
Campagnolo Training Center
REV.06 96
Installation
Cable run and installationInstallation of the cranksetBottom bracket cup tightening torque 35 Nm with tool UT‐BB130Crankset tightening torque: 42‐60 Nm
49
Campagnolo Training Center
REV.06 97
Installation
Cable run and installationInstallation of the rear derailleurtightening torque: clamp on versione 5 Nm; brazed on version 7 Nm
Campagnolo Training Center
REV.06 98
Installation
Cable run and installationInstallation of the front derailleur observing the distance from the largest chainring (1.5 – 3 mm) and the parallelism between the derailleur cage and the chainring itself
50
Campagnolo Training Center
REV.06 99
Installation
Cable run and installationInstallation of the interface
Fit elastic ring and adhesive rubber
Campagnolo Training Center
REV.06 100
Installation
Cable run and installationInstallation of the control connectors
51
Campagnolo Training Center
REV.06 101
Installation
Cable run and installationFunctional test of the system after installation: remove the system shut‐off magnet, the green led on the power unit will blinck, and activate levers 2, 3 and the mode button of each command, whilst observing the interface LED.
The blincking of the green led happens only if the magnet was inserted for a certain time (about 30 s, it can be shorter if the handlebars levers are activated )
Campagnolo Training Center
REV.06 102
Installation
Cable run and installation
The final phases of installation are:
•completion of installation of the controls
•power unit cable protection
•installation of rubber grommets
•chain installation
52
Campagnolo Training Center
REV.06
Position the control connector as illustrated in the photo below, being careful that the cable runs in the channel shown and close the cover.
103
Installation
Cable run and installation
Campagnolo Training Center
REV.06 104
Installation
Cable run and installationPower unit cable protection
53
Campagnolo Training Center
REV.06 105
Installation
Cable run and installationInstallation of the 3 rubber grommets in the holes near the interface,…
Campagnolo Training Center
REV.06 106
Installation
Cable run and installation…the rear and front derailleur
54
Campagnolo Training Center
REV.06 107
Installation
Cable run and installationChain
Install the chain in accordance with the procedure required for the mechanical groups using the tool UT‐CN300
Campagnolo Training Center
REV.06 108
Installation
Cable run and installation
After completing the installation of the EPS group, we are now ready to carry out the adjustments.
55
Campagnolo Training Center
REV.06 109
3
2
4
5
Adjustments after installation
1
6
• The phases• The rear derailleur reset procedure• The rear derailleur mechanical
travel limit• Jockey cage distance adjustment• The front derailleur reset procedure• Conclusion
Campagnolo Training Center
REV.06
The EPS system, after installation, needs to know the position of 2 sprockets and of one chainring, in order to calculate the position of all the other sprockets and of the other chainring.
Additionally it’s necessary to make a mechanical setting of the rear derailleur for a perfect functionality and to avoid any possibility that the rear derailleur might touch the spokes.
In the following page are the phases of the adjustment after the installation.
110
The phases
Adjustment after installation
56
Campagnolo Training Center
REV.06
A. Rear derailleur reset
B. Rear derailleur travel limit adjustment
C. Jockey cage distance adjustment
D. Front derailleur reset
E. Test on the road of the EPS system with evaluation of the behaviour of the transmission
F. Correction of the system behaviour with the front and/or rear derailleur adjustment or resetting of the front and/or rear derailleur.
111
The phases
Adjustment after installation
Campagnolo Training Center
REV.06
The rear and front derailleur reset procedures are fundamentalfor proper operation of the system.
These procedures allow the system to learn the reference positions of the chain on the sprockets and the chainrings from which it can then calculate the position to assume in all operating conditions.
During the reset phase movements of the rear and front derailleur take place continuously, and not with fixed movements as during adjustment, depending on the time that rear derailleur levers 2 and 3 are held in.
It is possible to modify the position by just a few hundredths of a millimetre.
112
The reset procedures
Adjustment after installation
57
Campagnolo Training Center
REV.06 113
Rear derailleur reset procedureThis procedure allows the system to learn the position of the 2nd
and 10th sprocket with respect to the rear derailleur drop‐out attachment.
Starting from these two reference positions, the system will calculate the position of all the other sprockets.
In the 11 speed units the distance between the two adjacent sprockets is 3.8 mm except:
•between the 1st and 2nd it is 4.3 mm for 11 t smallest sprocket and 4.2 mm for 12 t smallest sprocket
•between the 2nd and 3rd it is 3.94 mm for 11 t smallest sprocket
Overall tolerance for each sprocket position with respect to the first: +/‐0.1 mm.
Adjustments after installation
Campagnolo Training Center
REV.06
1. Position the front derailleur on the large chainring and the rear derailleur on the 11°sprocket (or on the 10° if the system doesn’t reach the 11°sprocket).
114
Rear derailleur reset procedure
Adjustments after installation
58
Campagnolo Training Center
REV.06
2. simultaneously press the two MODE buttons until the blue LED lights (about 6 seconds)
115
Rear derailleur reset procedure
Adjustments after installation
Campagnolo Training Center
REV.06
3. position the rear derailleur on the 2nd sprocket
4. adjust the position by pressing buttons 2 and/or 3
116
Adjustments after installation
Rear derailleur reset procedure
59
Campagnolo Training Center
REV.06
5. press the right MODE button to store the position of the 2nd sprocket
6. position the rear derailleur on the 10th sprocket
117
Rear derailleur reset procedure
Adjustments after installation
Pay attention when pressing Lever 2 ‐ the speed of movement of the rear derailleur isnot constant and it’s possible for the rear derailleur to run into the spokes.
Campagnolo Training Center
REV.06
7. adjust the position by pressing buttons 2 and/or 3
8. short‐press the right MODE button to store the position of the 10th sprocket and to conclude the procedure.
118
Rear derailleur reset procedure
Adjustments after installation
60
Campagnolo Training Center
REV.06
After resetting the rear and front derailleurs it is essentialto adjust the mechanical travel limit screw which ensures that the rear derailleur does not move inward to the point of interfering with the spokes of the rear wheel.
119
The rear derailleur mechanical travel limit
Adjustments after installation
Campagnolo Training Center
REV.06
In order to obtain a more rapid and accurate shift, the distance of the top jockey wheel from the largest sprocket (11th) must be adjusted.
The adjustment screw is in the same position as the mechanical rear derailleurs.
120
Rocker distance adjustment
Adjustments after installation
61
Campagnolo Training Center
REV.06
The distance must be about 5 – 7 mm.
121
Top jockey wheel distance adjustment
Adjustments after installation
Campagnolo Training Center
REV.06 122
Front derailleur reset procedure
In this procedure we position the front derailleur on the smallest chainring and the rear derailleur on the 11th sprocket (the largest).
Adjust the distance of the inside plate of the front derailleur cage from the inside surface of the chain to 0.5 mm.
Starting from this position, the system calculates the position of the largest chainring and all of the proportional travel based on the position requested by the user.
Adjustments after installation
62
Campagnolo Training Center
REV.06 123
Front derailleur reset procedure Position the front derailleur on the smallest chainring and the rear derailleur on the 11th
sprocket (the largest)
Adjustments after installation
Campagnolo Training Center
REV.06
1. simultaneously press the two MODE buttons until the blue LED lights (about 6 seconds)
124
Front derailleur reset procedure
Adjustments after installation
63
Campagnolo Training Center
REV.06
2. adjust the position by pressing lever 2 and/or 3 until the distance between the chain and the drop‐out is about 0.5 mm (use a feeler gauge if necessary)
3. press the left MODE button to store the position and finish the procedure
125
Front derailleur reset procedure
Adjustments after installation
Campagnolo Training Center
REV.06
In the event that, after entering the rear or front derailleur reset phase, the MODE button is not short‐pressed to finish the procedure, the procedure will not end and will remain active.
The system operates but movement of the rear or front derailleur is continuous and not in steps, as in normal operation.
It is ABSOLUTELY necessary to exit the procedure and carry out the reset again if required
126
Failure to finish reset
Adjustments after installation
64
Campagnolo Training Center
REV.06
The next phase is to check that the transmission works correctly on the road.
If the shifting isn’t perfect on the road, it may be necessary to make the adjustment of the rear or/and front derailleur as seen in the first chapter.
If the system still doesn’t work perfectly, repeat the resetting of the rear or/and front derailleur.
127
Conclusion
Adjustments after installation
Campagnolo Training Center
REV.06 128
4
2
3
5
Maintenance
1
6
• Routine maintenance• Special maintenance
65
Campagnolo Training Center
REV.06
Although the system meets the IP67 standards of water infiltration resistance, we would notrecommend washing the bicycle with pressurisedwater and aggressive detergents.
Periodically clean and lubricate the pivots of the derailleurs with a suitable oil for thermo‐plasticcomponents
Never use denatured alcohol to clean the power unit.
129
Cleaning
Maintenance
Routine maintenance
Campagnolo Training Center
REV.06
Power system
In order to prevent damage to the system battery pack, the system automatically switches off when it reaches 9 Volts to prevent dropping under this voltage.
If 7.2 Volts are reached, the system also shuts down other electronic components to prevent further energy absorption, protecting the battery from damage
130
Routine maintenance
Maintenance
66
Campagnolo Training Center
REV.06
Without use on the road
131
Routine maintenance
Maintenance
Campagnolo Training Center
REV.06
We therefore strongly recommend recharging the battery once the interface LED turns off.
The times indicated in the previous outline relate to temperatures up to 35°C and can drop significantly with an increase in temperature. Therefore storage of the power unit or the complete bicycle at a higher temperature for several months is not recommended.
132
Routine maintenance
Maintenance
67
Campagnolo Training Center
REV.06
Ergopower controls
Lever 1 can be replaced as with mechanical systems.
133
Special maintenance
Maintenance
Campagnolo Training Center
REV.06
Front derailleur
134
Special maintenance
Maintenance
The cage and the plate on the cage can be replaced as with mechanical systems.
Be careful not damage the component because the 3 pivots are inserted with a press since they have a knurled area for an interference fit. Use Molikote 40 grease on the pivots.
68
Campagnolo Training Center
REV.06 135
5
2
3
4
Diagnostics
• Diagnostics by the end customer
• Diagnostics by technical support service
• Malfunctions without the LEDs turning on
1
6
Campagnolo Training Center
REV.06
The EPS system can automatically detect various malfunctions.
In the event that a malfunction is detected, the EPS system turns on a LEDon the power unit.
Depending on the area in which the malfunction was detected, the LED takes on different colours based on the following table:
136
Diagnostics by the end customer
Diagnostics
69
Campagnolo Training Center
REV.06
WHITE Power system
YELLOW Front derailleur
GREEN Rear derailleur
BLUE Front derailleur control
VIOLET Rear derailleur control
RED Interface system
137
LEDs on the power unit
Diagnostics
Diagnostics by the end customer
Campagnolo Training Center
REV.06
Since, in some situations, the LED on the power unit may light because of a temporarymalfunction, the operations in the following pages are suggested for the end customer.
If the LED turns back on after these procedures have been followed, the customer should contact an Authorised Service Centre
138
Diagnostics by the end customer
Diagnostics
70
Campagnolo Training Center
REV.06
Power system: contact an Authorised Service Centre
Front derailleur: give a command and short‐press the MODE button
Activate the front derailleur: if it operates correctly, turn the LED off by short pressing the MODE button. If it does not operate properly and the LED remains on, contact an Authorised Service Centre
139
Diagnostics
Diagnostics by the end customer
Campagnolo Training Center
REV.06
Rear derailleur: give a command and short‐press a MODE button
If it does not operate properly and the LED remains on, contact an Authorised Service Centre.
140
Diagnostics
Diagnostics by the end customer
71
Campagnolo Training Center
REV.06
Rear derailleur control: If lever 2 or 3 was pressed for more than 9 seconds, this LED will light.
SOLUTION: short‐press a MODE button
If the rear derailleur does not operate properly and the LED remains on after this has been done, contact an Authorised Service Centre
141
Diagnostics
Diagnostics by the end customer
Campagnolo Training Center
REV.06 142
Diagnostics
Front derailleur control: If lever 2 or 3 was pressed for more than 9 seconds, this LED will light. SOLUTION: short‐press a MODE button. If the front derailleur then operates correctly, turn the LED off by short‐pressing the MODE button. If it does not operate properly and the LED remains on, contact an Authorised Service Centre
Diagnostics by the end customer
72
Campagnolo Training Center
REV.06 143
Diagnostics
Interface system: SOLUTION: short‐press a MODE button. If the system still does not operate properly and the LED remains on, contact an Authorised Service Centre
Diagnostics by the end customer
Campagnolo Training Center
REV.06
In case of a fall or accidental impact on the rear derailleur, it may «disengage» (to avoid damage).You will notice this because the rearderailleur will not shift into the smallersprockets.We recommend to take the rear derailleur to the smallest reachable sprocket, stop pedalling and act repeatedly on lever 2.
144
Diagnostics
Rear derailleur disengaged due to impact
Diagnostics by the end customer
In order to verify whether the rear derailleur is hooked again, drop down to the 1st sprocket: If this has not occurred "manually force"the rear derailleur. After successful re‐engagement, check the alignment of the drop‐out/rear derailleur mount and proper operation of the rear derailleur.
73
Campagnolo Training Center
REV.06
In normal operation, the rear derailleur works by the motor driving the yellow female screw. The female screw is locked by a trasvere screw that pushes a ballbearing into a depression.When the rear derailleur is disengaged, the sphere runs into the external channel on the female screw and so, independently from the motor activation, permits the user to change the position of the rear gear.
145
Diagnostics
Rear derailleur disengaged due to impact
Diagnostics by the end customer
Campagnolo Training Center
REV.06
Position of the rear derailleur disengaged
146
Diagnostics
Rear derailleur disengaged due to impact
Diagnostics by the end customer
depressionchannel
74
Campagnolo Training Center
REV.06
If the battery goes flat on the road, it is possible to ‘disengage’ the rear derailleur manually so that the user can move the rear derailleur position onto any of the lower sprockets.Once ‘back home’ remember to re‐engage the rear derailleur and to re‐charge the battery.
147
Diagnostics
‘Ride back home’ function
Diagnostics by the end customer
Campagnolo Training Center
REV.06
Since in some cases the EPS system is not able to detect a malfunction or the malfunction does not cause the LED on the power unit to light, please follow the EPS fault troubleshooting flow chart. In some cases the chart refers to diagnostics based on the colour of the power unit LED or it indicates the diagnostics to follow where no LED lights.
148
Diagnostics
Diagnostics by technical support service
75
Campagnolo Training Center
REV.06 149
Diagnostics
Diagnostics by technical support service
Campagnolo Training Center
REV.06
The procedures which should be followed in the event that a LED on the power unit lights are listed below.
150
Diagnostics
Diagnostics by technical support service
76
Campagnolo Training Center
REV.06
Power systemCAUSE: malfunction of power electronics.
SOLUTION: the component must be replaced.
Once the new component is installed, since the memory of the rear and front derailleur positions were stored in the original unit, the rear and front derailleur reset procedure must be carried out again.
151
Diagnostics
Diagnostics by technical support service
Campagnolo Training Center
REV.06
Front derailleurCAUSES: connector disconnected, damaged cabling (cable or terminal) and / or malfunctioning electric motor.
SOLUTION: visually check that the connector is properly connected, disconnect it, check to see whether there are traces of water, dirt, oxidation or abnormalities in the pins and reconnect the connector, after eliminating any abnormalities found. If necessary, use antioxidizing products. If this does not work and the LED remains on, check the entire cable that goes from the front derailleur to the power unit to ensure that there are no cuts, crushed sections or other abnormalities.
152
Diagnostics
Diagnostics by technical support service
77
Campagnolo Training Center
REV.06
Front derailleurIf an abnormality has been detected with the power system cable, replace the power unit. If an abnormality has been detected with the front derailleur cable or if no abnormality is detected, replace the front derailleur.
Once the new component is installed, the front derailleur reset procedure must be carried out again.
153
Diagnostics
Diagnostics by technical support service
Campagnolo Training Center
REV.06
Rear derailleurCAUSES: connector disconnected, damaged cabling (cable or terminal) or / and malfunctioning electric motor.
SOLUTION: visually check that the connector is properly connected, disconnect it, check to see whether there are traces of water, dirt, oxidation or abnormalities in the pins and reconnect the connector, after eliminating any abnormalities found. If necessary use antioxidizing products.
If an abnormality has been detected with the power system cable, replace the power unit. If an abnormality has been detected with the rear derailleur cable or if no abnormality is detected, replace the rear derailleur.
Once the new component is installed, the rear derailleur reset procedure must be carried out again.
154
Diagnostics
Diagnostics by technical support service
78
Campagnolo Training Center
REV.06
Rear derailleur controlCAUSE: one or more of the 3 circuits remain constantly closed (pressed buttons mechanically ‘stuck’, dome deformed, short circuit in cabling, water causing a short circuit).
SOLUTION: check that the control hoods do not press on the lever
in an abnormal way or foul levers 2 and 3.Visually check that the connector is properly connected, disconnect it, check to see whether there are traces of water, dirt, oxidation or abnormalities in the pins and reconnect the connector, after eliminating any abnormalities found. If necessary use antioxidizing products.
155
Diagnostics
Diagnostics by technical support service
Campagnolo Training Center
REV.06
Rear derailleur control
If it operates correctly, turn the LED off by short‐pressing the MODE button.
If an abnormality with the interface system cable has been detected replace the interface system. If an abnormality has been detected to the control cable or if no abnormality was detected replace the control.
Once the new component is installed the error must be cancelled by short‐pressing the MODE button.
156
Diagnostics
Diagnostics by technical support service
79
Campagnolo Training Center
REV.06
Front derailleur commandCAUSES: one or more of the 3 circuits remain constantly closed (pressed buttons mechanically ‘stuck’, dome deformed, short circuit in cables, water which causes a short circuit).
SOLUTION: check that the control hoods do not press on the lever in an abnormal way or foul levers 2 and 3.
Visually check that the connector is properly connected, disconnect it, check to see whether there are traces of water, dirt, oxidation or abnormalities in the pins and reconnect the connector, eliminating any abnormalities found. If necessary use antioxidizing products.
157
Diagnostics
Diagnostics by technical support service
Campagnolo Training Center
REV.06
Front derailleur controlIf it operates correctly, turn the LED off by short‐pressing the MODE button.
If an abnormality with the interface system cable has been detected replace the interface system. If an abnormality has been detected to the control cable or if no abnormality was detected replace the control.
Once the new component is installed the error must be cancelled by short‐pressing the MODE button.
158
Diagnostics
Diagnostics by technical support service
80
Campagnolo Training Center
REV.06
Interface system:
The LED turns on or a fault is detected only when the magnet is initially removed and the system turns on.
CAUSE: cable or connector or internal electronics.
SOLUTION: Visually check that the connector is properly connected, disconnect it, check to see whether there are traces of water, dirt, oxidation or abnormalities in the pins and reconnect the connector once any abnormality is corrected. Position the magnet in the housing on the power unit, wait about 10 seconds and remove the magnet: if the LED turns back on, check the entire cable which goes ... (ctd)
159
Diagnostics
Diagnostics by technical support service
Campagnolo Training Center
REV.06
Interface system
... from the interface to the power unit, ensuring that there are no cuts, crushed sections or other abnormalities.
If an abnormality is found with the power unit cable replace the power unit. If an abnormality has been detected with the interface system cable, or if no abnormality is detected, replace the power unit.
Once the new component is installed the error must be cancelled.
160
Diagnostics
Diagnostics by technical support service
81
Campagnolo Training Center
REV.06
In some cases, as indicated in the troubleshooting chart, electrical malfunctions occur without the LEDs on the power unit turning on:
•one or more circuits of the rear and front derailleur are interrupted
•battery is completely flat
161
Diagnostics
Malfunctions without the LEDs turning on
Campagnolo Training Center
REV.06
One or more circuits of the rear and front derailleur are interrupted:This is the normal situation when the rear or front derailleur control is not being activated by the user, because the switch the control operates is open. Therefore the system does not ‘see’ this as a malfunction. When the defective circuit's lever is activated the system does not activate the requested command because there is an additional break in the circuit. Check the entire cable that goes from the interface to the rear or front derailleur control, ensuring that there are no cuts, crushed sections or other abnormalities.Visually check that the connector is properly connected, disconnect it, check to see whether there are traces of dirt, oxidation or abnormalities in the pins and reconnect the connector after correcting any abnormality.If no abnormality is detected, replace the control.
162
Diagnostics
Malfunctions without the LEDs turning on
82
Campagnolo Training Center
REV.06
Battery is completely flat: The system does not have sufficient energy to indicate the excessively low charge level of the battery.
163
Diagnostics
Malfunctions without the LEDs turning on
Campagnolo Training Center
REV.06 164
6
2
3
4
Spare parts and warranty
1
5
• Product options• Accessories• Spare parts• Warranty: terms and
conditions/what is covered• Warranty: management
83
Campagnolo Training Center
REV.06 165
I ricambi e la garanzia
Some components of the EPS system must be chosen based on kind of installation on the frame required and depending on the geographical area where the system will be used:•power system bracket•BB cups•power cable for battery charger
Product options
Campagnolo Training Center
REV.06 166
Spare parts and warranty
Product options
POWER SYSTEM AC12‐HOSTDEPS POWER SYST. BRACKET + VIBRATION DAMP. AB
POWER SYSTEM AC12‐HOOPTEPS POWER SYST.BRACKET FIXED HT.
BATTERY CHARGER AC12‐CACEEEPS EEC POWER CABLE
BATTERY CHARGER AC12‐CAUSEPS AMERICAN TYPE POWER CABLE
BATTERY CHARGER AC12‐CAUKEPS BRITISH TYPE POWER CABLE
BATTERY CHARGER AC12‐CAAUSEPS OCEANIA TYPE POWER CABLE
84
Campagnolo Training Center
REV.06 167
I ricambi e la garanzia
We are producing new cups, to fit the BB cable guide, that are also compatible with mechanical series.
The new cups will be marked: EPS COMPATIBLE.
We’ll also produce new BBright cups (Cervelo)
Product options
Seriesthread /
press fitCode Name
Mechanical
series
compatibility
SUPER RECORD italian OC12‐SRI outboard cups SUPER RECORD™ ULTRA‐TORQUE™ ‐ IT yes
SUPER RECORD english OC12‐SRG outboard cups SUPER RECORD™ ULTRA‐TORQUE™ ‐ BSC yes
‐ press fit IC12‐SR41 Ultra Torque™ OS‐Fit™ integrated cups 86,5x41 yes
‐ press fit IC12‐SR42 Ultra Torque™ OS‐Fit™ integrated cups BB30 68x42 yes
‐ press fit IC12‐RE46 Ultra Torque™ OS‐Fit™ integrated cups BB30 68x46 yes
RECORD italian OC12‐REI outboard cups RECORD™ ULTRA‐TORQUE™ EPS ‐ IT yes
RECORD english OC11‐REG outboard cups RECORD™ ULTRA‐TORQUE™ ‐ BSC yes
Campagnolo Training Center
REV.06 168
Spare parts and warranty
Accessories
PART CODE DESCRIPTION
COMMANDS R1137084 LARGE HANDS INSERT KIT FOR EPS
FRONT DER FD‐SR001EPS FRONT DER. STIFFNESS INCREASER
FRONT DER R7204008 CHAIN SAVER SYSTEM
FRONT DER DC12‐SR2B SR Ø 32 mm BLACK clamp front derailleur
FRONT DER DC12‐SR5B SR Ø 35 mm BLACK clamp front derailleur
EPS AC12‐CAADBBEPS CABLE EXTENTION KIT
EPS AC12‐CAADSPEPS UNDER SADDLE CABLE EXTENTION KIT
85
Campagnolo Training Center
REV.06 169
Front derailleur mount stiffness increaser
It guarantiees a perfect working of the front derailleur even with ‘brazed on’ type mountings with low stiffness.In particular it’s necessary with carbon frames with carbon ‘brazed on’ mountings, where one can sometimes reach up to 10 mm of movement by forcing the derailleur cage with the hands.
Spare parts and warranty
Accessories
Campagnolo Training Center
REV.06 170
Front derailleur stiffness increaser
Spare parts and warranty
Accessories
It’s composed of two hinged pieces kept open by a spring. The position can be locked by a screw that can be tightened or loosened with an Allen wrench.
Installation procedure
1.Unscrew the screw, close the 2 sides and lock it with an Allen wrench.
86
Campagnolo Training Center
REV.06 171
Front derailleur stiffness increaser
Spare parts and warranty
Accessories
2. Install the stiffness increaser on the ‘frame’ side of the front derailleur, screwing the mounting screw in the threaded hole provided in the derailleur body.
Campagnolo Training Center
REV.06 172
Front derailleur stiffness increaser
Spare parts and warranty
Accessories
3. Install the front derailleur on the frame.
4. Put the rubber piece provided on the frame where the stiffness increaser touches it.
5. Unscrew the screw, and when the stiffness increaser opens, re-tighten the screw in order that the stiffness increaser touches both the frame and the front derailleur.
87
Campagnolo Training Center
REV.06 173
Spare parts and warranty
Accessories
CHAIN GUARD
Campagnolo Training Center
REV.06 174
Chain guard
The chain saver system guarantees that, when the chain descends to the smallest chain ring, it doesn’t drop onto the bottom bracket shell, even if external forces push on it.It’s suggested for:•racing use if under pressure the mechanic doesn’t set the front gear correctly•racing use where it may be necessary to shift to the smallest chainring on bends•use of the bike on poor road surfaces or pavè
Spare parts and warranty
Accessories
88
Campagnolo Training Center
REV.06 175
Chain guard
It’s compulsary for:•use of the bike on particularly badly surface roads, pavè as in Paris-Roubaix, etc or other cobblestonepaving.•Cyclo-cross races
Spare parts and warranty
Accessories
Campagnolo Training Center
REV.06 176
Spare parts and warranty
Accessories
CABLE EXTENTION KIT
89
Campagnolo Training Center
REV.06 177
Spare parts and warranty
Spare partsPART CODE DESCRIPTION
REAR DERAILER R1119250 REAR DERAILER AXLE ROCKER S.REC‐REC
REAR DERAILER R1119253 EPS REC REAR DERAILER AXLE ROCKER
REAR DERAILER R7350671 MECHANICAL TRAVEL LIMIT SCREW
REAR DERAILER R1102380 REAR DERAILER BODY WITHOUT ROCKER ASSEMBLY
REAR DERAILER R1102370 S.REC REAR DERAILER BODY WITHOUT ROCKER ASSEMBLY
COMMANDS HANDLEBAR FIXING CLAMP BRACKET
COMMANDS R118128‐129 EP REC COMMAND without lever 1
COMMANDS R118126‐127 EP S.REC COMMAND without lever 1
COMMANDS R1241208‐209 EP S.RECORD EPS LEVER 1
COMMANDS R1241210‐211 EP RECORD EPS LEVER 1
COMMANDS R1137098/099 COVER + 2 SCREWS
COMMANDS R1137100 8 SCREWS
COMMANDS R1137083 EPS BRACKET COVER PKG
Campagnolo Training Center
REV.06 178
Spare parts and warranty
Spare parts
PART CODE DESCRIPTION
FRONT DERAILER R1137085 EPS NUT+WASHER KIT FOR FRONT DERAILLEUR
FRONT DERAILER R1137090 EPS 5pcs FRONT DERAILLEUR CAGE INSERT KIT
FRONT DERAILER R7136211 EPS COVER FOR FRONT DERAILER ROCKER ASSEMBLY
FRONT DERAILER CAGE RECORD
FRONT DERAILER CAGE S.RECORD
INTERFACE R1137101 3 (O‐RING + PLASTIC + ADHESIVE PLUG) INTERFACE SYSTEM
POWER R1134886 MAGNET PKG 5 PCS
SPECIAL TOOL R1318001 MAGNETS KIT
SPECIAL TOOL ELECTRICAL CONNECTOR OPENER TOOL
90
Campagnolo Training Center
REV.06 179
Spare parts and warranty
Warranty
Procedure for the end customer
In case of malfunction, after having conducted any checks suggested on the instruction sheet, the end customer must contact an Authorised Service Centre for the additional, necessary checks to be carried out, which the ASC is equipped to perform.
Campagnolo Training Center
REV.06 180
Spare parts and warranty
WarrantyProcedure for the dealer/Pro Shop
In the event that malfunctions are found after having conducted the prescribed checks, the dealer or Pro Shop sends the defective component, after reporting, to the Authorised Service Center in their country.
Together with the component, the dealer or Pro Shop also sends the EPS Check Control document, filled in as far as the customer and dealer / Pro Shop are concerned.
91
Campagnolo Training Center
REV.06 181
Spare parts and warranty
WarrantyProcedure for the Service Center The Service Center, based on the indications from the dealer / Pro Shop, conducts:1.a visual/mechanical check2.a functional check connecting the component to the EPS group in its possessionImmediately sends a new component to the dealer / Pro Shop, completes the EPS Check control document and sends it, together with the defective component, to the Vicenza headquarters.
Campagnolo Training Center
REV.06 182
Spare parts and warranty
Warranty
Procedure for the Service Center
In order to provide optimum service for the end customer, the Authorised Service Centre will keep a stock of components to be sent to the dealers / Pro Shops in case of malfunctions covered under warranty.
This is because during the 1st year all defective components must be immediately returned to the Vicenza headquarters.
92
Campagnolo Training Center
REV.06 183
Spare parts and warranty
Warranty3 year warranty
The Record EPS and Super Record EPS groups, in addition to the 2 year warranty (or 3 for chainset, chain and sprocket), have a warranty extention of 1 year, power unit excluded, if:
•they are used on the same bicycle
•they are registered on the Campagnolo web site
•the components subject to wear are replacedwith Campagnolo components.
Campagnolo Training Center
REV.06 184
Thank you for your attention
top related