as1200 moederbord
DESCRIPTION
AS1200 moederbord. AS1200 moederbord. P W F. I²C -Bus (seriëel). REL. Micro- controller. AS1225. AS1220. AS1225. AS1221. DP2. EEPROM. DP1. AS1222. B3. B4. B1. B2. B3. B4. B1. B2. I / O. AS1200 Structuur. Hoe het programma werkt. Hallo, mijn naam is teller. Sensoren - PowerPoint PPT PresentationTRANSCRIPT
AS1200 moederbord
AS1200 moederbord
AS1200 Structuur
REL
Micro-controller
P W F
I / O
I²C -Bus (seriëel)
EEPROM DP1
B1 B2
DP2
B3 B4
AS1225
B1 B2
AS1225
B3 B4
AS1220 AS1221 AS1222
Hoe het programma werkt
Externe
Commando’s
filter
I/O status
Slagboombeheer
RESET
Sensoren (DP)
Time-outBewegings-
omkering
1 32
Hallo, mijn naam is
teller.
Beschrijving
• 1:1 to 10 Aansluitklemmen
• 1:11 Transformator 230/24V -
500mA
• 1:12 Microcontroller
• 1:13/14 Testknop open/dicht
• 1:15 DIP Switch SW4
• 1:16/17 Programmatie knop / led
• 1:18/19 Zekeringen
• 1:20/21 Uitgangs-relais
• 1:22/23 Mono-fazige motorrelais
• 1:24 to 28 LED ’s
1:3 1:4 1:26 1:21 1:20
1:7
1:25
1:8
1:11
1:14
1:131:17
1:16
1:15
1:1
1:2
1:27 1:22 1:23 1:18 1:19
1:10
1:28
1:5
1:6
1:24
1:12
1:9
Aansluitingen
• X1 Voedingsaansluiting
• X2 Aansluiting voor monofazige motor
• X3/4 Sensorkaarten voor DP1 tot DP4-functie
• X5 Uitbreidingskaart (AS1220 - AS1226)
• X6 Uitbreidingskaart (RS232 - AS1221)
• X7/8 I/O Input - Output aansluitingen
• X9 Aansturing voor AS1206 (3 fase
contactor)– X11 Voor de AS1033 - console
X7 en X8 aansluitingen1-2
24 VDC Aansluiting
3 openingscommando n°1 (NO contact)
4 0 Volt
5 sluitcommando n°1 (NO contact)
6 0 Volt
7 stopcommando n°1 (NC contact)
8 stopcommando n°1 (NC contact)
9 geblokkeerd open (NO contact)
10 0 Volt
11 Geblokkeerd gesloten (NO contact)
12 0 Volt
13 Relais 1: gemeenschappelijk
14 Relais 1: NC
15 Relais 1: NO
16 Relais 2: gemeenschappelijk
17 Relais 2: NC
18 Relais 2: NO
19 DP2 detectiesensor
20 DP2 detectiesensor
21 DP1 detectiesensor
22 DP1 detectiesensor
23 openingscommando n°2 (NO contact)
These commands must be bypassed if they are
not used.
24 0 Volt
25 openingscommando n°3 (NO contact)
26 0 Volt
27 sluitcommando n°2 (NO contact)
28 0 Volt
29 sluitcommando n°3 (NO contact)
30 0 Volt
31 stopcommando n°2 (NC contact)
32 stopcommando n°2 (NC contact)
33 stopcommando n°3 (NC contact)
34 stopcommando n°3 (NC contact)
35 zwengel eindeloopcontact FCM
36 +24V DC (de voedingsspanning gaat via deze aansluiting door het zwengel-eindeloopcontact en zo wordt de sturing spanningsloos gemaakt als de zwengel geplaatst is.)
37 eindeloopcontact open stand FCO
38 0 Volt
39 Eindeloopcontact FCF
40 0 Volt
41 DP4 detectiesensor
42 DP4 detectiesensor
43 DP3 detectiesensor
44 DP3 detectiesensor
Aansluitschema : Drie-fazige voeding
LED ’s
LD 1 (1:24) : Groen, watchdog ( processor/programma = OK)
LD 2 (1:17) : Rood, programmatie indicators en uit-bedrijf signalisatie
LD 3 (1:25) : Groen, eindeloopcontact open stand
LD 4 (1:25) : Groen, eindeloopcontact gesloten stand
LD 5 (1:25) : Groen, zwengelbeveiligingscontact
LD 6 (1:25) : Groen, openingscommando (OVB)
LD 7 (1:25) : Groen, sluitcommando (FRB)
LD 8 (1:25) : Groen, stopcommando (STOP)
LD 9 (1:25) : Groen, geblokkeerd open commando (BLQO)
LD10 (1:25) : Groen, geblokkeerd gesloten commando (BLQF)
LD11 (1:26) : Groen, relais REL1 actief
LD12 (1:26) : Groen, relais REL2 actief
LD15 (1:27) : Groen, relais REL3 actief
LD16 (1:27) : Groen, relais REL4 actief
LD17 (1:28) : Oranje, 24V DC
LD18 (1:28) : Oranje, 5V DC
DIP Schakelaars van SW4
DIP 1-2 Keuze van de werkingsmodus (zie tabel hieronder)
DIP 3 ON Intensieve test
DIP 4 ON Activatie van parameter 13: "Stroomuitval modus"
DIP 5 ON Weergave van de geprogrammeerde data op een PC. Deze optie dient ook voor foutdiagnose.
DIP 6 ON ON = Overbrugging van de drie STOP commando’s
DIP 7 OFF Niet toegewezen : altijd OFF
DIP 8 ON EEPROM programmatie
DIP 1 DIP 2 Mode Omschrijving
OFF OFF 0 Het openings- en sluitbevel zijn aangesloten op aparte aansluitingen. De aansluiting OVB opent de slagboom en FRB sluit de slagboom.
OFF ON 1 "Input -slaaf": alleen het openingsbevel is aangesloten. Een gesloten contact op de OVB aansluiting opent de slagboom en bij het wegnemen van dit contact sluit de slagboom opnieuw. De FRB klemmen worden niet gebruikt.
ON OFF 2 "Impuls relais": alleen het openingsbevel is aangesloten. Een impuls op de OVB klemmen inverteert het huidige bevel (bij elke puls verandert de motor van de slagboom van draairichring). De FRB klemmen worden niet gebruikt.
Dank u voor uw aandacht