asian issue - (주)육천건설 · 2012-03-20 · shoe width — 1,120mm wide as standard. track...

28
ASIAN ISSUE (주)육천건설 Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Upload: others

Post on 01-Apr-2020

1 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

ASIAN ISSUE

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

leeth
Typewritten Text
(주)육천건설 Yuekchun Const. Co. Ltd TEL +82 22691 6000 FAX +82 22691 6001 Web : y6000.co.kr E-mail1 : [email protected] E-mail2 : [email protected]
Page 2: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

2

Specifications

UPPER REVOLVING FRAME:All-welded, precision machined, robustconstruction. A machined surface providedfor mounting load hoist and boom hoistassemblies, and mounting itself on turntablebearing. And pins bail frame with a 12-sheave machinery and single center sheaveof a 21.0 D/d ratio for 2×12-part boom hoistreeving.

TURNTABLE BEARING WITH INTERNAL SLEWING GEAR:Heavy duty, single shear ball type; inner raceof turntable bearing with integral, internalswing (ring) gear bolted to lower frame, andouter race of turntable bearing bolted to upperrevolving frame.

CONTROL SYSTEM:System contains two sets of triplicate tandemvalves which direct oil to various machinefunction and are actuated by control levers viaremote controlled hydraulic servo for allmotions. Working speeds can be preciselycontrolled by motorcycle type throttle andpilot-operated arm chair single axis controllevers in cooperation with “EPC” controllerthat varies engine rpm and hyd. pumpdischarge simultaneously, or varies just hyd.pump discharge while keeping engine rpm viamotorcycle type grip throttle. System alsotakes a specially-tailored unique hydrauliccircuit to maximizes drum horsepower, andreduces horsepower loss with eliminating thepossibility of engine stall.

Pump control system — By “EPC” controller thatprovides two modes of engine-pump control.MODE I:The “EPC” Controller is normally programmedto vary the engine speed and pump dischargesimultaneously. Simply twisting the gripadvances the engine to maximum speed andthe hydraulic pumps to maximum flow at thesame time. This mode is suitable to precisioncrane work.MODE II:By activating a switch, it is able to vary justthe pump discharge by means of the gripthrottle, while keeping engine speed fixed.Mode II is convenient for operations such aslifting magnet and bucket work, where theengine is normally run at full throttle.

A specially-tailored pressure compensating valve —Utilized in hydraulic circuits to realize a goodminute operation of two main, boom hoist andopt. luffing jib hoist drums.

HYDRAULIC SYSTEM:System provided with three variabledisplacement axial piston pumps and onefixed displacement duplicate tandem gearpump for both independent and combinedoperations of all functions. Gear pump alsoused for system valves and cylinder controls.

Main/aux. crane hoist motors — Variable dis-placement axial piston motor withcounterbalance valve and spring-applied/hydraulically released multiple wet-disc typeautomatic brake as std.

Boom hoist motor — Variable displacement axialpiston type with counterbalance valve andspring-applied/hydraulically released multiplewet-disc type automatic brake.

Luffing jib hoist drum motor — Optional extra; axial

SuperstructureHITACHI SUMITOMO

ASIAN ISSUE

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 3: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

piston type with counterbalance valve andspring-applied/hydraulically released multiplewet-disc type automatic brake; available forluffing jib hoisting/lowering.

Slewing motor — Two; axial piston type with spring-applied/hydraulically released multiple wet-disc type brake; electrically controlled frominstrument panel of operator's cab.

Travel motors — Shoe-in design; axial piston motorwith brake valve and spring-applied/hydrauli-cally released multiple wet-disc type automaticbrake.

Oil cooler — Aluminum-make; located at a part ofsuperstructure as separated from engineradiator together with an independentautocooling fan for better cooling efficiencyand heat balance.

Hydraulic oil reservoir — 450 liters capacity.Kind of hyd. oil — Standardized with ISO VG46

having viscosity ranging from 41.4 thru50.6mm2/sec at 40°C.

BOOM HOIST ASSEMBLY:Twin-drum design; driven by single bi-directional, axial piston hydraulic motorthrough a 3-stage planetary reduction gearunit powering the rope drum in either directionfor hoisting and lowering boom.

Brake — Spring-applied, power hydraulically releasedmultiple wet-disc type automatic brake.

Drum — One piece, twin-design, parallel grooved laggingwith locking ratchet wheel cast integral; bolted toplanetary reduction gear unit outer case.

Drum lock — Power hydraulically operated automaticpawl.

Drum rotation speed control — Max. rotation speedcan be tuned according to arbitrary value thatis electrically controlled by dialing, and thenvaries pump discharge.

LUFFING JIB HOISTING MECHANISM:Optional extra; driven by bi-directional, axialpiston hydraulic motor through 2-stageplanetary reduction gear unit powering therope drum in either direction for hoisting andlowering luffing jib; required when rear drumis used for l i f twork with tower head topsheave machinery. Mounted on boom bottomsection.

Brake — Spring-applied, power hydraulically releasedmultiple wet-disc type automatic brake;provided within hydraulic motor.

Drum — One piece, parallel grooved lagging withlocking ratchet wheel cast integral; bolted toplanetary reduction gear unit outer case.

Drum lock — Power hydraulically operated automaticpawl.

Drum rotation speed control — Max. rotation speedcan be tuned according to arbitrary value thatis electrically controlled by dialing, and thenvaries pump discharge.

SLEWING:Driven by two units of bi-directional, axialpiston hydraulic motors through 2 sets ofplanetary reduction gear unit powering swingpinion. Swing pinion meshes with internalteeth of swing (ring) gear of turntable bearinginner race.

Brakes — Spring-applied, power hydraulicallyreleased multiple wet-disc type; provided oneach of hydraulic motor.

Slewing speed control — Max. slewing speed canbe tuned according to arbitrary value that iselectrically controlled by dialing, and thenvaries pump discharge.

Lock — Mechanically operated drop pin.Speed — 1.5min.–1 <1.5rpm>

OPERATOR’S CAB:A 2.3mm thickeness steel plate constructionwith 940mm wide and a stamped-and-rounded corner designs; acoustically treated,full-vision, cushion rubber mounted, well-ventilated, full compartment, roomy operator’scab with a large straighted front window withgreen-tinted safety glass; provided with anarrangement of “EPC” control/slewing lever,armchair control station, sunvisor, sunshade,rear-view mirrors, dual intermittent typewindow shield wipers with washer on bothfront and roof windows, sliding windows onboth sides of cab, and swing-link type slidingdoor.

Swing-away mechanism — Provided as standard;available to set a 3-meter overall width ofsuperstructure for a good transport.

Tilting mechanism — Power hydraulically tiltable cabis standrdized for a good upward visibility.

Instrument panel — Contains engine monitoringlamps, graphic display panel of Load MomentIndicator, gauges & meter, warning lamps andother necessary controllers and switches.

Operator’s seat — Full adjustable reclining seat withhead rest and both R/H and L/H side armrests.

Air-conditioner — Provided as std.; built-in type fullair-conditioning.

Electric cab fan — Optional extra; wind-directionadjustable type.

Anemometer — Optional extra; recomimened forluffing jib attachment.

Engine foot throttle — Optional extra; available forright-hand foot with electrical control.

Electric outlet — 24V; available in cab.Operator’s cab sidestep — Available for access

ease to operator’s cab.AM/FM radio — Provided as std. with clock.Fire extinguisher — Optional extra; powder type with

1kg capacity.Drum brake pedals — Optional extra;

correspondingly designed in the case that anoptional free-fail function is reqired on twomain operating drums.

MACHINERY CAB:Equipped with hinged doors on both sides formachinery access and inspection; affixedtape-type non-skid material on the roof.

CATWALKS:Optional extra; hitched in place along bothsides of machinery cab.

HYDRAULIC TAGLINE WINDER:Optional extra; provided in front of upperrevolving frame, and this is available forpreventing a shake of suspended load like

3

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 4: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

clamshell bucket by an 10mm dia. tug cablewith light force.

COUNTERWEIGHTS:Weighs 102.8ton consisting of a 22.4ton baseweight and a 12-piece cast iron block of80.4ton in its total.

Counterweight self-removal device — Provided asstd.; raises and lowers a 102.8ton fullcounterweight by a lifting mechanism with twopower hyd. cylinders attached on the baseweight.

ELECTRICAL SYSTEM:24-volt negative ground system; provided withtwo maintenance free 12-volt batteries.

LIGHTING SYSTEM:Includes following lights.• Two 70 W working lights;• One 10 W interior cab light.

POWER UNIT:

A PORTABLE ENGINE-HYDRAULIC POWER PACK:Optional extra; available to supply powerhydraulic to hydraulic cylinders as used asrear post backstops. Required when luffing jibatt.

LOWER FRAME:All-welded, precision machined, box typeconstruction; provided with four tip blocksw/pins and lugs to hook and then assemblecrawer side frames on.To mount turntablebearing, a machined surface is provided too.

Hyd. removal joint-pins — Four; available to hold inplace crawler side frames on carbody framewith a face-contact design to bear reactionforce of crawler side frame. And, four pins areeach operated by hyd. cylinder thru remotecontrol box shown in clause of “LOWERFRAME JACK-UP DEVISCE” below.

LOWER FRAME JACK-UP DEVICE:Contains four hydraulic jack cylindersattached on lower frame jack cylinder beamsfor disassembling/assembling ease of crawlerside frames.

Remote control box — Provided for control of lowerframe jack cylinders and hyd. removal joint-pins.

Pontoon — All-welded construction; four pontoonseach attached on outside of carbody weight.

CRAWLER SIDE FRAMES:All-welded, box type construction, precisionmachined; each provided with two steel platehooks for an assembling ease on carbodyframe. Held in place by hydraulic removalheavy duty joint-pins provided on four tipblocks of carbody frame.

Crawler side steps — Provided at both ends of theframes for easy access to superstructure.

LOWER WEIGHT:Weighs 18ton; made of cast iron. A 9ton eachmounted on carbody jack cylinder beamsprovided at front and rear of the carbody.

DRIVE SPROCKETS:Cast steel, heat treated; one per side frame.Track drive sprocket assembly bolt-coupled to3-stage planetary reduction gear unit outercase as an integral part of shoe-in typetraction motor. Sealed between parts ofrotation and non-rotation of the motor withfloating seal.

IDLER WHEELS:Cast steel, heat treated; one per side frame.Mounted on two bronze bushings with floatingseals for lifetime lubrication.

TRACK ROLLERS:Thirteen per side frame; each heat treatedcast steel with double flange design. Allrollers mounted on two bronze bushings withfloating seals for lifetime lubrication.

4

Make & ModelType�

No. of CylindersBore & StrokeDisplacement

Rated Output

Maximum Torque

Fuel Tank

Mitsubishi 6M70–TLWater-cooled, 4-cycle,�direct injection, turbo-charged, diesel w/automatic cooling fan

Six (6)130 mm × 150 mm

12,880 cc

272 kW/2,000 min–1�

〈370 ps/2,000 rpm〉

1,510 N·m/1,600 min–1�

〈154 kgf-m/1,600 rpm〉 500 liters

Notes:1. The engine meets Stage/Tier 3 of current smoke

emission regulations in Europe, America and Japan.

2. A 272kW engine horsepower shown above isdefined under a current international engine horsepower indication formula which includes necessary horsepower for engine alternator drive but excludes engine fan drive.

Undercarriage

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 5: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

CARRIER ROLLERS:Three per side frame; each heat treated caststeel with double flang design. All rollersmounted on bronze bushings with floatingseals for lifetime lubrication.

TRACKS:Heat treated, self-cleaning, multiple hingedtrack shoes joined by full floating pins; 58 pcs.per side frame.

Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with

oil jack and shim plate packs is standardized. Automatic track tension adjusting device —

Optional extra; available instead of std. trackadjustment to always keep track tension atoptimum level by means of power hyd.cylinder thru idler wheel actuated by powerhydraulic supplied from superstructure.

TRAVEL AND STEERING:A bi-directional, shoe-in type axial pistonhydraulic motor bolt-couples drive sprocket thru3-stage planetary reduction gear unit outer caseat each crawler side frame end for travel andsteer. Straight-line travel (forward or reverse),pivot or differential turns, and counter-rotation forspin turns are available.

Brake — Spring-applied, hydraulically releasedmultiple wet-disc type automatic brake; locatedwithin hydraulic motor. Brakes automaticallyset when travel levers are in neutral or whenengine is shut down.

Travel speed — 1.1/0.5km/hr. (based on flat, leveland firm supporting surface, and under theconditions that no load must be applied andfront-end att. must be 15.25m basic boomonly).

Gradeability — 30% (17°) permissible based on basicmachine without front-end attachment.

LOAD MOMENT INDICATOR:This is a fully computerized automatic over-load preventing system including total safeoperation control system; provided with thedesigns of (1) no zero-point adjustment, (2) datainput according to interface counter-indication/message on display panel, and (3) agraphic display panel with setting ease ofviewing angle.

Construction (standard version) — Comprises (1)load detecting device with amplifier, (2) boomangle detector, (3) computerized MicroProcessing Unit (M.P.U.), and (4) graphicdisplay panel.

Functions — This system functions that if the liftingload reaches 90% of the rated one specifiedin the crane capacity chart, an intermittentpre-warning buzzer is given; if it is 100%, a

warning is given by a continuous buzzer, andall peri l side motions are automaticallystopped. The machine, however, can beoperated in safety side motions.

Display panel design — A graphic display panel isdesigned, and it is able to input necessaryoperating conditions/data according to interfacecounter-indication/message on the display panel,and the display panel indicates ten and somekinds of the present lifting and workingconditions/data like “l i f t ing load”, “max.allowable lifting load”, “working radius”, “max.allowable working radius”, “boom angle”, “loadratio”, “boom/jib lengths”, “engine rpm” and soon when working. In addition, the displaypanel is provided with three warning indicatorsover “engine over-heat”, “hyd. oil over-temp.”and “brake oil over-temp.”.

HOOK OVER-HOIST LIMITER:Limit switch type. Available to prevent hookover-hoisting with functions of automatic drumbraking with hydraulic lock, and warnings byan alarm.

BOOM OVER-HOIST AND -LOWERING LIMITING DEVICE:Available in two kinds of devices; one is limitswitch located on a part of boom foot forpreventing boom over-hoisting, and the otheris the safety function of the LMI available toautomatically prevent boom over-hoisting and-lowering with the functions of automatic drumbraking with hydraulic lock, and warnings byan alarm. Further boom protection from rapidboom over-hoist by hook over-hoist motionunder mal-function of hook over-hoist limitingdevice is available as one of functions of the LMI.

BOOM BACKSTOPS:Dual; telescopic design with spring buffers.

DUAL BOOM OVER-HOIST LIMITING DEVICE:Additional l imit switch located on boombackstops; this is as a further safety devicefor redundant boom protection.facing front or rear or left or right to undercarriage.

SLEWING LOCK:Mechanically operated drop pin; available tofirmly lock superstructure in four positions offacing front or rear or left or right to undercarriage.

DRUM LOCKS:Electrically operated pawl locks is available onfront and rear main drums while powerhydraulically operated pawl lock is availableon boom hoist drum with an automatic lockingdevice as std.

FREE-FALL INTERLOCKING DEVICE:Available on both front and rear main drumbrake lines for fail-safe operation. Functionsthat free-fall brake mode is only availablewhen drum brake pedal is pressed eventhough brake mode is switched on free-fallmode.

5

Safety Devices

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 6: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

6

SLEWING BRAKE SAFETY CIRCUIT:Available not to start engine whenever swingbrake is off.

NON-DRUM BRAKE PREVENTING DEVICE:Available not to start engine whenever drumbrake mode is in “free-fall”.

BOOM ANGLE INDICATOR:Pendulum type; mounted on right-hand side ofbottom section of crane main boom.

HOOK LATCH:Provided on every kinds of hook to preventout of place of cable from hook.

LEVEL GAUGE:Bubble type; located on operator’s cab floorand a part of undercarriage.

LEVER LOCKS:Provided on all control levers (except swinglever) to lock levers in neutral.

SLEWING ALARM:This is by buzzer, and flasher lamps locatedon both sides of machinery cab.

SPEED SLOWDOWN DEVICE:This is for speed slowdown of hoisting andlowering motions of boom which are availablejust before automatic stopping at both upperand lower side limits of boom angle eventhough control lever(s) is sti l l athoisting/lowering position to prevent a shock.

SLEWING BRAKE LAMP:Provided on operator’s cab instrument panel;this is available to confirm whether or notslewing brake is applied.

SIGNAL HORN:Available as warning just before every kindsof motions are initiated.

FOOL PROOF SHUT-OFF SYSTEM:Located in the cab exit; this is available toautomatically deactivate and lock hydraulicsystem.

TRAVEL ALARM:An intermittent buzzer warns when travelmotion is initiated.

ENGINE MONITORING LAMPS:Available to let operator warn engine abnormalconditions as to battery charge, lubrication oilpressure, radiator coolant level, oil filterclogging, air filter clogging, water temp.,contorol unit and glow plug.; provided oninstrument panel.

FRONT-END ATT. ERECTION MODE:This is an internal, integral function of the LMI.In the range out of crane working area, the LMIdisplay panel automatically indicates “Now, outof crane working range” with a rigginginstruction, and it is available to lift front-end att.off ground without the influence of LMI safetyfunctions, and, after front-end att. is lifted over

the range of crane working area, LMI safetyfunction gets back automatically for safeerection work. This function is also available forthe work of vice-versa.

LIFTING HEIGHT METER:Available to indicate l ift ing height aboveground or depth below ground on displaypanel of the LMI. Also, hook hoisting speedslowdown function is available just beforeautomatic stopping at a desired height underhook height setting before operation.

LMI SAFETY CIRCUIT-OFF SWITCH:Available in key type for a good crane safetyoperation management without fail.

TRAVEL DIRECTION ARROW:Attached each on crawler side frames.

GAUGES & METER:Engine water temperature gauge, fuel gaugeand hour-meter are provided on instrumentpanel.

WARNING LAMPS:Available to let operator warn abnormalmachine conditions as to pilot pressure andbrake system of two main and opt. luffing jibhoist drums; provided on instrument panel.

REAR VIEW MIRRORS:Two; each provided on front-left and -rightcorners of superstructure.

DRUM MIRROR:Available to check rope winding onto frontand rear drums from operator's cab.

THREE COLOR PERCENTAGE INDICATOR:Optional extra; this is with three colours ofGreen, Yellow and Red. Each colourindicates the load percentage to ratedcapacity; Green shows less than 90% assafety, Yellow shows 90 to 99% as marginal,and Red shows over 100% as over-loading.As further function, Red lamp comes onautomatically when operator cuts off safetycircuit of LMI absent-mindedly.

MICROPHONE & LOUD-SPEAKER:Optional extra; this is for operator’sconvenience for loud speaking.

DRUM LIGHT:Optional extra; available for checking ropewinding onto front and rear drums.

AUX. CRANE HOOK OVER-HOIST LIMITING DEVICE:Optional extra; this is available for auxiliarycrane hoist with optional. short jib and/or flyjib. Performs the same function as that of“Hook over-hoist limiting device” mentionedbefore.

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 7: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

CRANE BOOM:Lattice construction, round tubular main chords, alloy, hi-ten steel, with bracing of round steel tubing.Boom connections........................................In-line pin connections at 2.10m deep and 2.10m wide.Basic boom .............................................Two-piece, 15.24m basic length; 7.62m heavy-duty base and tapered top

sections. Provided with boomfoot pin removal cylinders.Boom head machinery.................................Five head sheaves, and two guide sheaves mounted on anti-friction bearings

of conventional non-sealed grease type.Six-hanger sheave block ............................Optional extra; pinned to boom head shaft. Sheaves each mounted on anti-

friction bearings of conventional non-sealed grease type. Required when liftingload exceeds 145ton, and available up to 275ton lift.

Five-hanger sheave block...........................Optional extra; pinned to boom head shaft. Sheaves each mounted on anti-friction bearings of conventional non-sealed grease type. Required when liftingload exceeds 145ton, and available up to 250ton lift.

Ultra heavy-duty boom extensions ..............Optional extra; available in 3.05m, 6.10m and 12.20m with pendants.Heavy-duty boom extension ........................Optional extra; available in 12.20m with pendants.Maximum boom length.................................91.45m meters.

Note: All of ultra heavy- and heavy-duty boom extensions are designed with no intermediate diagonal bracing(s); the diagonal bracing isonly designed at one of two picture frames. Accordingly, it is able to nest luffing jib extension into appropriate boom extension inlength.

FLY JIB:Optional extra; lattice construction, round tubular main chords, alloy, hi-ten steel, with bracing of round steel tubinghaving in-line pin connections at 1.0m deep and 1.0m wide, and jib head machinery with single sheave mounted onantifriction bearings of conventioral non-grease type. Provided with jib strut, jib backstops, and jib/boom guylinependants. Mounted on 7.62m tapared top section, and available for light load lifting operation with less than 27ton withtwo-part hoist line. Single part hoist line is also available for a 13.5ton lift as max.Basic fly jib ...................................................Two-piece, 12.20m basic length; 6.10m base and top sections.Fly jib extensions .........................................Available in 6.10m length with pendants.Maximum fly jib length .................................36.55m.Boom plus fly jib length ...............................Max. 70.1m + 36.55m.

AUXILIARY SHORT JIB:Optional extra; all-welded construction having single sheave head machinery. Pinned to 7.62m tapered top section.

BOOM LIVE MAST:A 7m long; all-welded, box construction. Mounted in front of upper revolving frame, and pins bridle frame with a 12-sheavemachinery of a 21.0 D/d ratio for a 2x12-part boom hoist line. Raised by two power hyd. cylinders from transportationposition to a certain working position as a short boom for self-assembling work as this mast is available to use for self-assembling of a whole machine without helper crane in cooperation with hydraulic counterweight self-removal device, andqucik-draw power hydraulic cylinder with hook attached onto the mast. In addition, a 2-large diameter single pendant ropeof short length with plate link is pinned on top of the mast for easy connection with a 2-dual extender cables.

MID-POINT SUSPENSION LINK:Optional extra; required when boom length exceeds 88.40m.

7

Front-end Attachment

In addition to the above, following safety devices arestandard for luffing jib attachment.

LUFFING JIB ANGLE DETECTOR:This is one of key safety device in a case ofluffing jib attachment.

LUFFING JIB LOAD DETECTOR:This is also important safety device whenluffing towercrane attachment is required.

LUFFING JIB OVER-HOIST AND -LOWERING LIMITINGDEVICE:

Performs all the same function as that of“Boom over-hoist and -lowering l imit ingdevice” stated before.

LUFFING JIB HOOK OVER-HOIST LIMITING DEVICE:Performs the same function as that of “Hookover-hoist lifting device” described before.

LUFFING JIB BACKSTOPS:Dual; telescopic design with spring buffers.

DUAL LUFFING JIB OVER-HOIST LIMITING DEVICE:Additional limit switch located on tower jibbackstops; this is as a further safety devicefor redundant tower jib protection.

LUFFING JIB HOIST DRUM LOCK:Provided with automatic pawl-locking devicelike boom hoist drum pawl-locking (if luffing jibhoist drum is optionally provided).

REAR POST BACKSTOPS:Two power hydraulic cylinders are designedto easily set rear post position as necessarywhen assembling front post and luffing jib;power hydraulic is supplied to these cylindersby a portable engine-hydraulic power pack.

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 8: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

HOOK BLOCKS:275/145t, five sheaves plus 5-hanger sheave block with duplex type hook ....Optional extra.250/145t, five sheaves plus 5-hanger sheave block with duplex type hook ....Optional extra.145t, five sheaves with duplex type hook(275t use) .........................................Optional extra.145t, five sheaves with duplex type hook(250t use) .........................................Optional extra.80t, three sheaves..............................................................................................Optional extra.35t, one sheave..................................................................................................Optional extra.13.5t, ball hook ...................................................................................................Optional extra.Notes: An 145t hook block is each available from 250/275t hook block by dismounting a 5-hanger sheave block.

BAIL AND BRIDLE:All-welded construction; provided with larger sheaves of a 21.0 D/d ratio on both bail and bridle for 2×12-part boom hoistrope reeving. Bail pinned to upper revolving frame directly, and bridle pinned to boom live mast respectirely. And,pendant ropes bridge the gap between boom live mast and 7.62m tapered top section.

DRUM DATA:

Notes:1. Line speed is based on drum first layer and rated engine rpm with no load.2. Hoisting line speed varies under load and operating conditions.3. Crane hoist applications of front and rear main drums shall be upon kind of front-end attachment.

HOIST REEVING:

CABLES:Front drum ..................................................P·S (19)+39×P·7, non-spin type, 28mm dia./450m long, breaking load 755kN

(77.0t). Rear drum ...............................................Optional extra; P·S (19)+39×P·7, non-spin type, 28mm dia., breaking load

755kN (77.0t). Length depends on crane hoist applications as under:1. Fly jib application..................................................350m.2. Aux. short jib application......................................190m.

Boom hoist drum ......................................XP rope with construction of IWRC 6×P·WS (31), 22.4mm dia./320m long,breaking load 417kN (42.5t).

Luffing jib hoist drum ..............................Optional extra; XP rope with construction of IWRC 6×P·WS (31), 28mmdia./210m long, breaking load 657kN (67.0t).

8

����

����

���

��

����

� �� �� �� � � � � � � �

��� ���� ���

���� ���� ��� ���

���

��

��

���

���

���

���

���

���

���

���

� ����������

����

���

����

��

����

��� ��� ���

���

����

���� ��� ���� �������

�����

���� ���� �� ������ ����

�������� ������������� ����

��� ����

�������� ���� �!���� ��� "#$�� %%& ' (��� ()��(*"+,

�("�&����

�������� ���� ����� ��� "#$�� %%& ' (��� ()��(*"+,

�("�&����

�������� ���� �-��� .��� $*%�� ( × ((* ' %�&���� ((�*��%$"+,

�%$�#���� × (

�������� ���� ���//�� 0� .��� ������ "#$�� "" ' (��� ()��(*"+,

�("�&����

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 9: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

9

Liftcrane Capacities 275 metric tons

����� ����� ����� ��� ��� ����� ����� ����� ����� ���� ��� ��� ����� ���� ���� ����� ����

��

��

���

���

���

��

���

���

����

����

���

����

����

����

����

���

����

����

����

����

���

����

����

���

���

��

���

���

����

����

���

����

����

����

����

���

�����

�����

���

�����

�����

�����

�����

����

��� ���

���� ��

���

�����

�����

���

����

�����

����

�����

����

����

���� ���

����� ���

�����

�����

���

����

�����

����

�����

����

���

��

����

��� ����

����� ��

����

����

�����

�����

����

�����

���

���

���

���

���

��� ����

����� ���

����

����

����

�����

�����

����

���

��

��

���

���

��� ����

����� ���

�����

����

�����

�����

���

����

���

���

���

���

����

���

����

���� ����

����

���

�����

����

���

���

���

���

���

���

����

���

����

����

��� ����

����� ��

����

�����

�����

���

���

���

����

���

��

����

����

����

����

����

���� ���

�����

�����

�����

����

��

���

����

����

��

����

����

����

���

����

���

����

����� ��

�����

�����

����

���

����

��

���

��

���

��

����

����

����

���

����

����

��� ���

����� ���

�����

���

���

���

����

��

���

���

���

����

����

���

����

���

����

����

�� ���

��� ���

���

����

���

����

���

���

��

���

���

����

����

����

����

���

���

����

����

����

���� ���

����

���

���

����

���

���

���

����

���

����

��

����

����

����

����

���

����

����

���

��� ���

���� ����

����

���

���

����

��

���

���

����

����

��

���

���

����

����

���

����

����

���

����

���� ���

��� ���

��

����

���

���

���

���

���

���

����

���

��

����

���

����

���

����

���

����

����

����

���� ����

��� ����

���

���

����

����

��

���

����

���

����

���

���

����

����

���

���

����

���

����

����

����

����

����

��� ���

���� ����

���

���

��

���

���

����

���

���

���

���

����

����

���

����

����

���

����

����

����

����

��

���

��� ���

����� ���� ���� ���� ����� ���� ����

���

���

���

���

��

���

���

���

���

��

���

���

���

���

��

���

���

���

���

��

���

���

���

���

��

���

���

���

���

��

���

���

���

���

����

��� ���

��

���

����

����

���

���

���

���

����

����

����

���

����

����

����

����

����

����

���

��

��

���

���

��

���

���

��� ����

���� ����

����

����

����

����

���

����

���

����

���

����

��

���

����

����

����

����

����

����

���

��

���

��

���

���

��

���

��

��� ����

���� ����

����

���

��

���

����

����

���

����

����

����

���

����

���

����

����

����

����

���

��

���

���

���

���

���

���

���

���

���

��� ���

���� ����

����

���

����

����

���

���

����

����

����

���

����

����

����

����

���

����

���

��

���

���

��

���

���

���

���

���

���

���

��� ���

���� ����

����

����

��

���

����

����

����

����

����

���

���

����

����

����

����

����

���

��

���

��

���

���

��

���

���

���

��

���

��

���

��� ����

��� ����

��

����

����

����

����

����

���

����

���

��

����

����

����

����

����

����

���

��

���

���

���

���

���

��

���

��

���

��

���

���

���

���

���

��� ����

����

����

����

����

����

����

���

���

����

����

����

����

���

����

����

���

��

���

��

���

���

���

���

���

��

���

��

���

��

���

���

�������

���

���

����

���

����

���

����

���

��

����

����

����

���

����

����

����

���

����

����

��

���

��

���

��

��� ���

��� ����

���

����

����

����

����

���

����

����

����

���

����

���

����

����

����

���

����

����

��

���

��

���

��

���

���

��� ����

■WORKING MASS & GROUND PRESSURE:

Note: Working mass shown above is with 15.24mbasic boom, 102.8ton counterweight, 18tonlower weight and optional 275t hook block.

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 10: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

10

Notes — Liftcrane capacities1. Capacities included in these charts are the maximum

allowable, and are based on machine standing level on firmsupporting surface under ideal job conditions.

2. Capacities are in metric tons, and are rated in accordancewith European EN13000 Standards in terms of machinestability and structural strength limitations; the figuressurrounded by bold lines are based on factors other thanthose which would cause a tipping condition.

3.Capacities are based on freely suspended loads and make noallowance for such factors as the effect of wind, suddenstopping of loads, supporting surface conditions, and operatingspeeds. Operator must reduce load ratings to take suchconditions into account. Deduction from rated capacities mustbe made for weight of hook block, weighted ball/hook, sling,spreader bar, or other suspended gear.Hook block weight is as follows:275t...........4.3ton 250t ..........3.7ton145t...........3.3ton (275t use)145t...........2.7ton (250t use)80t.............1.4ton 35t ............0.9ton 13.5t ........0.6ton

4. All capacities are rated for 360° slewing.5. Least stable rated condition is over the side.6. An 102.8ton counterweight and 18.0ton carbody weight are

required for all capacities on this chart.7. Attachment must be erected and lowered over the ends of

the crawler mounting.8. Main boom length must not exceed 91.45m.

Maximum fly jib length permitted — 36.55m.Maximum boom plus fly jib combination length permitted —70.1m+36.55m.Maximum boom length when mounting short jib is 88.40m.

9. Capacities when handling load off main boom head sheavesin case of mounting fly jib or short jib on top of boom aredetailed; if required, please consult us or nearest distributor.

10. Boom combination shall be in accordance withmanufacturer’s standard described here in “BoomCombination Diagram” of page 16.

SCX2800-2 SHORT JIB CAPACITIES:Max. 13.5ton

Note: Jib capacities is almost equal to the figures made by thededuction of apporx. 600kg from the liftcrane capacities forboom length up to 88.40m unless restricted by themaximum jib capacity shown above. As to the details,please consult us or nearest distributor.

Short jib (Option)

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 11: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

11

Fly Jib Capacities 27 metric tons

�����

�� �� �� �� �� �� �� �� �� ��

����� ���� ����� ����� ����

�����������������������������������������������������������������������������

���������

�����������������������������������������������������������������������������������������

��������

������������������������������������������������������������������

�������

���������������������������������������������������������������

������

��������������������������������������������������������������������������������������

������

���������������������������������������������������������������������������������������������

�����

����������������������������������������������������

�������

����������������������������������������������������������������������������������

������

���������������������������������������������������������

�����

���������������������������������������������������������������������

�������

������������������������������������������������������������

��������

������������������������������������������������������������������������

��������������������������������������������������������������

�������

����������������������������������������������������������������������������������������������������������

�� �� ���� ����

48.75

10 30 10 30 10 30 10 30 10 30

12.20 18.30 24.40 30.50 36.55

27.0/12.827.027.027.027.027.026.625.023.522.221.120.119.118.217.516.815.614.513.512.611.711.0

10.6/55.0

2

13.5/13.013.513.513.513.513.513.513.513.513.513.513.513.513.513.513.513.513.513.512.611.711.0

10.5/55.7

1

13.9/16.313.613.112.612.111.811.311.010.710.510.110.09.79.59.39.19.08.98.88.7

8.7/55.7

2

13.5/16.713.513.112.612.111.811.311.010.710.510.110.09.79.59.39.19.08.98.88.78.7

8.7/56.5

1

23.4/14.723.122.421.821.320.820.319.118.117.116.215.514.814.113.613.012.612.111.611.310.910.610.09.3

9.1/60.7

2

13.5/14.913.513.513.513.513.513.513.513.513.513.513.513.513.513.513.012.612.111.611.310.910.610.09.3

8.8/61.5

1

10.1/20.59.89.59.18.88.68.38.07.87.67.47.27.06.96.86.66.56.46.46.36.2

6.2/62.6

1

13.5/16.913.513.513.513.513.513.513.513.513.513.212.612.011.511.110.610.29.89.59.18.88.68.37.9

7.5/67.2

1

7.8/24.37.57.37.06.86.56.36.16.05.85.65.55.45.35.15.05.04.94.84.74.6

4.6/68.7

1

11.8/18.811.611.311.010.610.410.19.89.69.49.18.98.68.38.17.97.77.57.37.17.06.96.56.36.1

6.0/72.9

1

6.1/28.15.95.75.55.35.15.04.84.74.54.54.34.24.14.04.03.93.73.63.5

3.5/74.8

1

8.1/20.78.07.87.47.06.86.56.26.05.75.55.35.15.04.84.64.54.44.34.14.03.83.63.53.4

3.3/78.6

1

4.7/31.94.74.54.54.34.24.14.03.93.73.63.53.43.33.23.23.02.92.82.72.72.71

12.314.016.018.020.022.024.026.028.030.032.034.036.038.040.042.044.046.048.050.052.054.056.058.060.064.068.072.076.080.080.8

No. of part line

51.80

10 30 10 30 10 30 10 30 10 30

12.20 18.30 24.40 30.50 36.55

27.027.027.027.027.027.027.025.724.323.021.820.719.819.017.816.515.314.113.112.211.310.69.9

9.3/57.7

2

13.5/13.413.513.513.513.513.513.513.513.513.513.513.513.513.513.513.513.513.513.112.211.310.69.99.3

9.1/58.4

1

13.9/16.713.613.112.712.311.911.511.210.910.610.310.19.89.69.59.39.19.08.98.88.88.7

8.7/58.3

2

13.5/17.213.513.112.712.311.911.511.210.910.610.310.19.89.69.59.39.19.08.98.88.88.7

8.7/59.1

1

23.3/15.223.122.521.921.521.020.519.718.617.716.716.015.314.614.013.513.012.512.111.611.010.39.69.0

8.1/63.4

2

13.5/15.413.513.513.513.513.513.513.513.513.513.513.513.513.513.513.513.012.512.111.611.010.39.69.07.9

7.9/64.1

1

10.1/21.09.99.69.28.98.68.38.17.97.77.57.47.17.06.96.86.66.56.46.46.36.2

6.2/65.2

1

13.5/17.313.513.513.513.513.513.513.513.513.513.313.012.411.811.411.010.610.19.89.59.18.98.68.17.4

7.0/69.8

1

7.8/24.87.57.37.06.86.66.46.26.05.95.85.65.55.45.35.15.05.04.94.84.6

4.6/71.3

1

11.8/19.211.611.311.110.810.510.210.09.79.59.39.08.88.68.38.17.97.67.57.37.17.06.76.56.2

6.0/75.6

1

6.1/28.56.05.85.55.45.25.04.94.84.64.54.44.34.14.14.03.93.73.73.63.5

3.5/77.4

1

8.1/21.28.17.97.57.16.96.56.36.05.85.65.45.35.04.94.84.64.54.34.24.13.93.73.53.43.3

3.3/81.3

1

4.7/32.34.64.54.44.24.14.03.93.73.73.53.53.43.33.23.03.02.92.82.7

2.7/83.5

1

13.214.016.018.020.022.024.026.028.030.032.034.036.038.040.042.044.046.048.050.052.054.056.058.060.064.068.072.076.080.084.086.1

No.of part line

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 12: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

12

54.85

10 30 10 30 10 30 10 30 10 30

12.20 18.30 24.40 30.50 36.55

27.0/13.727.027.027.027.027.027.026.625.123.722.621.520.519.117.616.215.013.812.811.811.010.39.58.88.3

8.2/60.3

2

13.5/13.913.513.513.513.513.513.513.513.513.513.513.513.513.513.513.513.513.512.811.811.010.39.58.88.3

8.0/61.0

1

13.9/17.213.813.312.812.412.111.611.311.110.810.510.310.09.89.69.59.39.19.08.98.88.88.4

8.1/60.9

2

13.5/17.613.513.312.812.412.111.611.311.110.810.510.310.09.89.69.59.39.19.08.98.88.88.4

8.1/61.7

1

23.2/15.623.222.622.121.621.120.620.219.118.217.216.515.815.114.513.913.412.912.311.510.69.99.38.67.5

7.0/66.0

2

13.5/15.813.513.513.513.513.513.513.513.513.513.513.513.513.513.513.513.412.912.311.510.69.99.38.67.5

6.7/66.7

1

10.1/21.410.09.69.39.08.88.58.38.07.87.67.57.37.17.06.96.76.66.56.46.46.2

6.2/67.8

1

13.5/17.813.513.513.513.513.513.513.513.513.513.513.312.812.211.711.310.810.510.19.89.59.18.98.17.06.1

6.0/72.5

1

7.8/25.27.67.47.16.96.66.56.36.16.05.85.65.55.45.35.25.15.05.04.84.74.6

4.6/73.9

1

11.8/19.711.711.411.110.810.610.310.19.89.69.39.19.08.78.58.38.07.87.67.57.37.16.96.56.45.6

5.2/78.2

1

6.1/29.06.05.85.65.45.35.15.04.84.64.54.54.44.34.14.04.03.83.73.63.53.5

1

8.1/21.68.17.97.57.37.06.66.46.15.95.75.55.45.15.04.94.74.54.44.34.24.03.83.63.53.4

3.2/83.9

1

4.7/32.84.64.54.44.34.14.03.93.83.73.63.53.43.43.23.13.02.92.82.72.72.71

13.214.016.018.020.022.024.026.028.030.032.034.036.038.040.042.044.046.048.050.052.054.056.058.060.064.068.072.076.080.084.086.1

No.of part line

57.90

10 30 10 30 10 30 10 30 10 30

12.20 18.30 24.40 30.50 36.55

27.027.027.027.027.027.027.025.824.523.222.120.618.917.316.014.713.612.611.610.810.09.38.68.1

7.3/62.9

2

13.5/14.313.513.513.513.513.513.513.513.513.513.513.513.513.513.513.513.512.611.610.810.09.38.68.1

7.1/63.6

1

13.8/17.613.713.413.012.612.111.811.511.210.910.610.410.110.09.89.69.49.39.19.08.98.88.2

7.1/63.6

2

13.5/18.113.413.012.612.111.811.511.210.910.610.410.110.09.89.69.49.39.19.08.98.88.27.0

6.8/64.4

1

23.2/16.122.722.221.721.320.820.419.618.717.717.016.215.514.914.313.813.112.111.210.59.79.18.47.36.4

6.2/68.7

2

13.5/16.313.513.513.513.513.513.513.513.513.513.513.513.513.513.513.513.112.111.210.59.79.18.47.36.4

6.2/69.4

1

10.1/21.910.19.79.49.18.88.68.38.17.97.77.57.47.27.07.06.86.76.66.56.46.36.2

6.1/70.5

1

13.5/18.213.513.513.513.513.513.513.513.513.513.413.112.612.111.611.110.810.410.19.89.59.07.96.86.0

5.4/75.1

1

7.7/25.77.67.47.17.06.86.56.46.26.05.95.85.65.55.45.35.15.15.04.94.84.64.6

4.6/76.6

1

11.8/20.111.511.110.910.610.410.110.09.79.59.39.18.88.68.48.18.07.87.67.47.37.06.76.25.44.7

4.5/80.8

1

6.1/29.56.05.85.65.55.35.15.04.94.84.64.54.44.34.24.14.03.93.73.73.53.5

3.5/82.7

1

8.1/22.18.07.67.47.06.86.56.36.05.85.65.45.35.15.04.84.64.54.44.34.03.93.73.53.43.3

3.2/86.6

1

4.7/33.24.64.54.44.34.14.04.03.93.73.73.53.53.43.33.23.02.92.92.72.72.7

2.7/88.81

14.116.018.020.022.024.026.028.030.032.034.036.038.040.042.044.046.048.050.052.054.056.058.060.064.068.072.076.080.084.088.091.4

No.of part line

60.95

10 30 10 30 10 30 10 30 10 30

12.20 18.30 24.40 30.50 36.55

27.0/14.627.027.027.027.027.027.026.525.223.922.320.318.717.115.714.513.312.311.310.59.79.08.37.76.6

6.3/65.6

2

13.5/14.813.513.513.513.513.513.513.513.513.513.513.513.513.513.513.513.512.311.310.59.79.08.37.76.6

6.0/66.3

1

13.8/18.113.513.112.612.312.011.611.311.110.810.610.310.19.99.79.69.49.39.19.08.67.96.8

6.2/66.2

2

13.5/18.513.513.112.612.312.011.611.311.110.810.610.310.19.99.79.69.49.39.19.08.67.96.8

6.0/67.0

1

23.2/16.522.822.321.821.421.020.620.119.118.217.416.716.015.314.813.812.811.811.010.19.48.88.17.06.0

5.3/71.3

2

13.5/16.713.513.513.513.513.513.513.513.513.513.513.513.513.513.513.512.811.811.010.19.48.88.17.06.05.1

1

10.1/22.39.89.59.28.98.68.58.28.07.87.67.57.37.17.06.96.86.66.56.56.46.25.5

5.3/73.1

1

13.5/18.713.513.513.513.513.513.513.513.513.513.513.312.812.311.911.511.110.710.310.09.38.77.56.55.64.9

4.5/77.7

1

7.7/26.17.57.37.06.86.66.56.36.16.05.85.75.55.55.45.35.15.04.94.84.74.6

4.5/79.2

1

11.7/20.611.511.311.010.710.510.210.09.89.69.39.19.08.88.68.48.18.07.87.67.57.16.85.95.14.4

3.9/83.5

1

6.0/29.96.05.95.75.55.45.25.04.94.84.64.54.54.44.34.14.14.03.83.73.63.53.5

3.5/85.3

1

8.1/22.58.07.87.57.47.27.06.96.66.66.46.26.06.05.85.65.55.45.25.04.84.64.44.24.03.93.4

3.2/89.21

4.9/33.74.94.64.54.44.34.14.03.93.83.73.63.53.43.43.23.03.02.92.82.72.72.71

14.116.018.020.022.024.026.028.030.032.034.036.038.040.042.044.046.048.050.052.054.056.058.060.064.068.072.076.080.084.088.091.4

No.of part line

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 13: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

13

64.00

10 30 10 30 10 30 10 30 10 30

12.20 18.30 24.40 30.50 36.55

27.027.027.027.027.027.027.027.025.823.821.920.118.316.715.314.113.012.011.010.19.38.68.07.46.35.3

5.3/68.2

2

13.5/15.213.513.513.513.513.513.513.513.513.513.513.513.513.513.513.513.012.011.010.19.38.68.07.46.35.3

5.2/68.9

1

13.8/18.513.613.112.812.412.111.811.511.210.910.610.510.310.19.89.79.59.39.39.08.37.66.55.4

5.2/68.9

2

13.5/19.013.513.112.812.412.111.811.511.210.910.610.510.310.19.89.79.59.39.39.08.37.66.55.4

5.1/69.7

1

23.1/17.022.922.422.021.521.120.720.219.618.717.817.116.415.814.613.512.411.510.69.89.18.47.86.65.64.8

4.5/73.9

2

13.5/17.213.513.513.513.513.513.513.513.513.513.513.513.513.513.513.512.411.510.69.89.18.47.86.65.64.8

4.3/74.7

1

10.1/22.89.89.69.39.08.88.58.38.17.97.87.57.47.37.17.06.96.86.66.56.46.25.3

4.4/75.8

1

13.5/19.113.513.513.513.513.513.513.513.513.513.513.413.112.712.211.811.311.010.59.79.18.47.26.25.34.53.9

3.7/80.4

1

7.7/26.67.57.37.06.96.76.56.46.16.05.95.85.65.55.45.35.25.15.04.94.74.64.0

3.7/81.9

1

11.7/21.011.611.311.110.810.610.310.19.89.69.59.39.18.88.78.58.48.28.07.87.57.36.55.54.84.03.4

3.1/86.1

1

6.0/30.45.95.75.55.45.35.15.04.94.74.64.54.44.34.24.14.03.93.73.73.53.53.0

1

8.1/23.08.07.87.67.47.37.06.96.76.56.46.36.16.05.95.75.55.55.35.24.94.64.54.34.13.63.0

2.5/91.8

1

4.9/34.14.74.54.44.34.14.04.03.83.73.73.53.53.43.23.13.02.92.82.72.72.7

2.5/94.0

1

15.016.018.020.022.024.026.028.030.032.034.036.038.040.042.044.046.048.050.052.054.056.058.060.064.068.072.076.080.084.088.092.096.096.7

No.of part line

67.05

10 30 10 30 10 30 10 30 10 30

12.20 18.30 24.40 30.50 36.55

27.0/15.527.027.027.027.027.027.026.225.123.221.219.517.916.315.013.712.611.610.69.89.08.37.57.05.94.9

4.3/70.9

2

13.5/15.713.513.513.513.513.513.513.513.513.513.513.513.513.513.513.512.611.610.69.89.08.37.57.05.94.9

4.2/71.6

1

13.8/19.013.713.312.912.512.211.811.611.311.110.810.610.310.110.09.89.69.59.38.67.97.26.05.0

4.3/71.5

2

13.5/19.413.513.312.912.512.211.811.611.311.110.810.610.310.110.09.89.69.59.38.67.97.26.05.04.1

4.0/72.3

1

23.2/17.423.122.622.121.721.220.820.420.019.118.317.516.815.514.313.112.111.110.29.48.68.07.46.25.34.43.7

3.5/76.6

2

13.5/17.613.513.513.513.513.513.513.513.513.513.513.513.513.513.513.112.111.110.29.48.68.07.46.25.34.43.7

3.5/77.3

1

10.1/23.29.99.69.39.18.88.68.48.28.07.87.67.57.47.27.17.06.96.86.66.55.94.94.0

3.5/78.4

1

13.5/19.613.513.513.513.513.513.513.513.513.513.513.513.313.012.512.111.611.010.19.38.68.06.95.95.04.13.5

3.0/83.0

1

7.7/27.07.57.47.16.96.86.56.46.36.16.05.85.75.65.55.45.35.25.04.94.84.53.73.0

2.9/84.5

1

11.6/21.511.611.311.110.810.610.410.110.09.89.69.39.19.08.88.68.48.28.07.87.67.16.15.24.43.73.02.5

2.4/88.8

1

6.0/30.86.05.85.65.55.35.15.04.94.84.64.54.54.44.34.14.03.93.73.73.63.42.7

2.3/90.6

1

8.1/23.48.17.97.67.37.06.86.56.36.15.95.75.55.45.25.04.94.84.64.54.34.13.93.73.63.22.72.2

1.8/94.5

1

4.6/34.64.54.54.44.34.14.04.03.93.73.73.63.53.43.23.23.03.02.92.82.72.51.91.81

15.016.018.020.022.024.026.028.030.032.034.036.038.040.042.044.046.048.050.052.054.056.058.060.064.068.072.076.080.084.088.092.096.096.7

No.of part line

70.10

10 30 10 30 10 30 10 30 10 30

12.20 18.30 24.40 30.50 36.55

15.916.018.020.022.024.026.028.030.032.034.036.038.040.042.044.046.048.050.052.054.056.058.060.064.068.072.076.080.084.088.092.096.0

No.of part line

27.027.027.027.027.026.124.823.722.621.620.619.217.716.314.913.612.511.510.69.68.88.17.56.95.74.83.9

3.7/73.5

2

13.5/16.113.513.513.513.513.513.513.513.513.513.513.513.513.513.512.511.510.69.68.88.17.56.95.74.83.9

3.5/74.2

1

13.8/19.413.813.313.012.612.312.011.711.411.111.010.710.510.310.19.99.89.69.38.57.87.16.05.04.0

3.6/74.1

2

13.5/19.913.513.313.012.612.312.011.711.411.111.010.710.510.310.19.99.89.69.38.57.87.16.05.04.0

3.4/74.9

1

23.0/17.922.922.622.121.721.220.920.520.219.618.717.816.615.314.113.012.011.010.19.38.67.97.36.15.14.33.5

3.0/79.2

2

13.5/18.113.513.513.513.513.513.513.513.513.513.513.513.513.513.012.011.010.19.38.67.97.36.15.14.33.5

2.8/79.9

1

10.0/23.710.09.69.49.18.98.78.58.38.17.97.87.67.57.37.17.06.96.86.76.55.84.84.03.2

3.0/81.0

1

13.513.513.513.513.513.513.513.513.513.513.513.513.212.812.311.810.810.19.38.67.96.85.74.84.03.32.7

2.5/85.7

1

7.6/27.57.67.47.17.06.86.66.56.36.16.05.95.85.65.55.55.45.35.15.04.84.53.72.9

2.4/87.1

1

11.6/21.911.611.311.110.910.610.510.210.09.89.69.59.39.18.98.78.58.38.18.07.87.06.05.14.33.52.92.4

1.9/91.4

1

6.0/31.36.05.85.65.55.35.25.04.94.84.74.64.54.44.34.24.04.03.83.73.63.42.72.0

1.9/93.21

8.1/23.98.17.97.67.47.16.96.66.46.16.05.85.65.55.35.15.04.94.74.64.44.14.03.83.73.12.52.0

1.8/94.01

4.6/35.04.64.54.44.34.14.14.03.93.83.73.63.53.53.33.23.03.02.92.82.72.41.81

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 14: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

14

Notes — Fly jib capacities1. Capacities included in these charts are the maximum

allowable, and are based on machine standing level on firmsupporting surface under ideal job conditions.

2. Capacities are in metric tons, and are rated in accordancewith European EN13000 Standards in terms of machinestability and structural strength limitations; the figuressurrounded by bold lines are based on factors other thanthose which would cause a tipping condition.

3.Capacities are based on freely suspended loads and make noallowance for such factors as the effect of wind, suddenstopping of loads, supporting surface conditions, and operatingspeeds. Operator must reduce load ratings to take suchconditions into account. Deduction from rated capacities mustbe made for weight of hook block, weighted ball/hook, sling,spreader bar, or other suspended gear.Hook block weight is as follows:35t.............0.9ton 13.5t .........0.6ton

4. All capacities are rated for 360° slewing.5. Least stable rated condition is over the side.6. An 102.8ton counterweight and 18.0ton carbody weight are

required for all capacities on these charts.7. Attachment must be erected and lowered over the ends of

the crawler mounting.8. Maximum fly jib length permitted — 36.55m.

Maximum boom plus fly jib combination length permitted —70.1m+36.55m.

9. Capacities when handling load off main boom head sheavesin case of mounting fly jibon top of boom are detailed; ifrequired, please consult us or nearest distributor.

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 15: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

8.0m

7.8m

6.3m7.4m

Hook lift allowance height:

13.5t (w/aux.short jib)

30t (w/fly jib)145/80/35t275/250t

12.20m Fly jib 18.30m Fly jib

24.40m Fly jib

30.50m Fly jib

36.55m Fly jib

15.25m

18.30m

21.35m

24.40m

27.45m

30.50m

33.50m

36.55m

39.60m

42.65m

45.70m

48.75m

51.80m

54.85m

57.90m

60.95m

64.00m

67.05m

70.10m

73.15m

76.20m

79.25m

82.30m

85.35m

88.40m

91.45m

Short jib

Short jib

10° 30°

1.50m

2.725m

81.5° 70° 60° 50°

40°

30°

12.20m Fly jib

18.30m Fly jib

24.40m Fly jib

30.50m Fly jib

36.55m Fly jib

8

12

16

20

24

28

32

36

40

44

48

52

56

60

64

68

72

76

80

4 8 12 16 20 24 3228 36 40 44 48 52 56 60

84

88

92

96

100

64 68 72 76 80 84 88

4

0

104

108

92 96 100

Hei

ght a

bove

gro

und

(m)

Working radius (m)

15

Liftcrane Working Ranges

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 16: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

16

Boom Combination Diagram

� ����� � �� � �����

� ����� � ��� � � ��� � �����

� ����� ����� � ��� �� �����

� ����� ����� � ��� �� �����

� ������ ����� � ��� �� �����

� ������ � ��� �� �����

�� �� � ������ � ��!� � ��� �"���� ���#� ��$ �� �� ����#��

�� % ���� ���& ' ( ������� � ���! ���!� �)� � ���� �� � ��� ��� ��!������ �� � ������ ������ ���� �� �� �� �� � �

��� � ���� �� �� ����� � ���� � � �� ��� ��� �����!� � ����* ��� � ��� ��� ��!������ #��� �� ���� ���& ' (

�� ��� �� �� �� �!�� �� ������ � �� � ��� � �����

Note:

Boom length Boom length(m)

Boom combination Boom combination(m)

15.25

18.30

21.35

24.40

27.45

30.50

33.50

36.55

39.60

42.65

45.70

48.75

51.80

54.85

57.90

60.95

64.00

67.05

70.10

73.15

76.20

79.25

82.30

85.35

88.40

91.45

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

���

������ ���

���

���

���

��� ���

���

���

��� ���

��� ���

��� ���

���

���� ����

��� ���� ���

���

���

���� ���

��� ���� ���

��� ���

���

���� ���

���� ���

���� ���

��� ���

���� ���� ���

��� ���� ���� ���

���� ���� ���

�������� ��� ���

���

���

���

���

���

��� ���

���� ���� ���

�������� ��� ���

�������� ��� ���

���

���

�������� ��� ������

�������� ��� ���

�������� ������ ���

�������� ������ ���

�������� ������ ���

�������� ������ ���

������

�������� ��� ������

���

���

��� ���

���

���

���

��� ���

��� ���

���

��������

����

������ ���

������� ������ ���

���� ������� ������ ���

���

�������� ������ ������

�������� ������ ��� ���

�������� ������ ��� ���

�������� ������ ��� ���

��� ��� �������� ������ ��� ���

���

���

���

���� ���� ���

��� ���

���

����

���

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 17: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

17

General Dimensions

Note: The above general arrangement is under liftcrane application with 15.25m basic boom, and optional 275t hook block.

����

����

����

��

����

������� � ��� �����

���� ���������� ���

����

��

����

���

���� ���

��

���

���

���

����

���

���

����

���� ����� ���� �

���� ����� ���� �

!�����"#

    �"����"�

$"�%��� ���� �

��� ���

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 18: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

18

Transport Data

����� ����

����

����

����

��������

���

����

��

���

����

����� ����

����

� ���� ���� � ���

���� ������

���� � ���

��� !"# �$��%��

&�'(���)

�"#� *� "��" � ����+

�, ���� � ���-�, .��� ��/� ��*� �'( ����-�, � �%� � "� ��(��-, .'0 � "� ��(��1 �%��, ���� � ��� 2�� !"#

��/���,

�"#� *� "��" � ����+

�, ���� � ���-�, .��� ��/� ��*� �'( ����-�, � �%� � "� ��(��1 �%�, .'0 � "� ��(��,

1���

�1���

3��1���

3���

3�1���

���,��

����

��,����

����

���

���

���

���

����

����

Dimensiors(mm)Description Q'ty Mass(kg)

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 19: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

19

����������� � ����� �����

������

������

�����

�������

��� ������� �

������� � !

������� � "

#$��� %& ����

��� '�����

���(��)���*��

�+��

����

����

����

����

�+��

���� +�,�

����

���

�,��

���

����

+#��

-��� . ����

��,�

��+� ����

����

���

���

,�,���#$��� %& ����

/�* '�����

���*����� �*��

���*����� �*��

Dimensiors(mm)Description Q'ty Mass(kg)

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 20: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

20

�����

�����

�����

��� � ��� �� ���

���������

���� � ��� �� ���

���������

���� �� ���

���������

������ ��� ��� �����!

������ ��� ��� �����!

������ ��� ��� �����!

����

����

����

����� ����

����

����� ����

����

"������ � ��� �� ���

���������

������ ��� ��� �����!

������ ��� �����!

����

����

����

#�����

#�� �� ���

���� $�%����

��� �&&��' (�) *���� ��!���)�%+�����!

"#��

,� �*- ����

����

Dimensiors(mm)Description Q'ty Mass(kg)

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 21: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

21

���� �� ����� � ��� ��� ����� �� ��������� � ��� �� ����������� ���� �� �� � ����

�����

���

� !����� "����#

� !����� "����#

���� $�% &��

'��� (�����

� !�"�#

���� $�% &��

��� (�����

��������

����

����

��)� ����

���

*��

� !����� "����#

���� $�% &��

+�������

(��" &��

��,� ����

��,�

��,�

���

��*�

��*���-���" �.�����"

(����� '���/

0��1

��*�

��)�

���

Dimensiors(mm)Description Q'ty Mass(kg)

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 22: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

22

���� �� ������� �� ���� ���� ���� � ��� ������ ���� �����

���� �� ����� �� ���� ���� ���� ��� �� ��������� ���� �� ���������� �� ���� �� ���� !����� ���� ��� �� �� ����������

" "������� #��� $����

%��&

'�� '��

��"�

����

���

�"�

� � "������ #��� $����

(�������� ���� ����)

"*"�

��

"�

��

"�

'��

� � ���+�� � �����

,��� $����

%��&

��"�"��

�"

��

Dimensiors(mm)Description Q'ty Mass(kg)

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 23: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

23

���� �� ������� �� ���� ���� ���� � ��� ������ ���� �����

��� �� ���������� ���� � � �� ���� �� ��� � �������� �� �� ��� ���� �� ��� � ������� �� ��� �� ��� �� �� ���������� �� ����� � �����!����� � �����!�����!����� ��� ��� ��� �� ����" ��� ��� ���� ���� ��� ������� ��� ���� �� ���� �����"�

#��

$��

%

� &��

' &��

% (��

%

%

%

%

���� )��� *����

+�!������ ���� ����,

%(�� )��� *����

-�� )��� *����

'�� )��� *����

%'��� *��� )��� *����

.��/

.��/

0����/ '#�

0����/ ���

&#�

'�'�

�%'�

&#

%�'�

'(�

%�%�

-%�

#(�

��'�

-%�

�$

��

��

-��

#(�

%-�

Dimensiors(mm)Description Q'ty Mass(kg)

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 24: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

24

Standard equipment Optional equipment

Standard and Optional Equipment

¡Luffing jib hoisting mechanism;¡Drum rollers; available on front/rear main drums;¡Fire extinguisher;¡Catwalks, along both sides of machinery

cab;¡Re-fuel pump;¡Engine foot throttle;¡Electric cab fan;¡Portable engine-hydraulic power pack;

required when luffing jib att;¡Reeving winch;¡Add. air cleaner element;¡Hyd oil filter;¡Boom hooking bracket.

Superstructure ¡Mitsubishi 6M70-TL diesel engine with a272kW <370ps> rated output;

¡Hydraulic system with three variabledisplacement axial piston pumps and one fixeddisplacement duplicate tandem gear pump;provided with an aluminum-make independentoil cooler;

¡Control system with one each of quadruplicateand triplicate tandem valves and pilot-operatedarm chair single axis control levers; providedwith motorcycle type “EPC” controller (easy-precise-minute engine rpm and hyd. pump oilflow control device), and specially-tailoredpressure compensating valves. In addition,drum rotation speed control is desighed on;

¡Front and rear main operating drum winchesof 245kN<25t> line pull with 596mm dia. drumlagging driven by independent variabledisplacement hyd. motor; each provided withmultiple wet-disc type automatic brake with nofree-fall function;

¡Boom hoist mechanism with a twin-drum designdriven by a hyd. motor with automatic brakes;provided with drum rotation speed control design;

¡Slewing mechanism with heavy-duty turntablebearing; driven by two hyd. motors w/spring-applied, power hydraulically released multiplewet-disc brakes; provided with speed controldesign;

¡Bail frame with a 10-sheave machinery andsingle center sheave; pinned to a rear part ofupper revolving frame;

¡940mm wide, full-vision operator’s cab with astamped-and-rounded corner design and largefront window; provided with an arrangement ofarmchair operator control station andinstrument panel. Slewing-away and tiltingmechanisms, and air-conditioner are providedtoo;

¡102.8ton counterweight; provided with a self-removal device for full weight;

¡Machinery cab with hinged doors;¡24-volt electrical system with two 12-volt batteries;¡Lighting system:

• Two 70W working lights;• One 10W interior cab light;

¡Accessories;• AM/FM radio w/clock;• Engine hourmeter; • Engine tachometer;indicated on displaypanel of LMI;

• Fuel gauge;• Eng. water temp. gauge;• Engine over-heat indicator; available on

display panel of LMI;• Hyd. oil over-temp. indicator; available ondisplay panel of LMI;

• 24V electric outlet;• Dual, intermittent window shield wipers withwashers; available on both front and roofwindows;

• Cigar lighter;• Ash tray;• Book holder;• Sunvisor;• Sunshade;• Cup Holder;• Non-skid surfaces;• Cab front step;• Cab sidestep;• Cab floor mat;• Superstructure under-cover.

¡Std. spare parts and tools.

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 25: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

25

Standard equipment Optional equipment

Undercarriage ¡7,520mm width by 9,045mm long crawler lowerwith removable crawler side frames; providedwith four of tip blocks with pins, lugs and hyd.joint-pin removal cylinders;

¡Crawler drive units with shoe-in type tractionmotor with wet-disc type automatic brakes;

¡Lower frame jack-up device w/4-vertical hyd.jack-up cylinder and remote control unit;

¡1,120mm wide track shoes;¡Manual track tension adjusting devices;¡18ton carbody weight;¡Lifetime lubricated track components;¡Crawler side steps.

Liftcrane Att. ¡15.25m basic crane boom; 7.62m base section,and 7.62m tapered top section w/five headsheaves, and two guide sheaves; provided withboom foot pin removal cylinders;

¡Boom live mast and bridle frame with a 12-sheave machinery; provided with “quick draw”power hyd. cylinder;

¡Main crane hoist cable; 28mm dia./450m long;¡Boom hoist cable; 22.4mm dia./320m long;

Liffting jib Att.

¡Automatic track tension adjusting device.

¡3.05m ultra heavy-duty boom extension;¡6.10m ultra heavy-duty boom extension; ¡12.20m ultra heavy-duty boom extension;¡12.20m heavy-duty boom extension;¡12.20m basic fly jib; 6.10m bottom and

top sections with jib strut and boom/jib quyline pendants;

¡6.10m fly jib extension;¡275/145t duplex type hook (145t hook with

5sheaves hanger block);¡250/145t duplex type hook (145t hook with

5sheaves hanger block);¡80t hook block;¡35t hook block;¡13.5t ball hook;¡Six-hanger sheave block (pinned to boom

head shaft); required together with 275thook block when lift ing load exceeds145ton, and available up to 275ton lift;

¡Five-hanger sheave block (pinned toboom head shaft); required together with250t hook block when lifting load exceeds145ton, and available up to 250ton lift.

¡Aux. crane hoist cable, 28mm dia./350mlong; available for fly jib application;

¡Aux. crane hoist cable, 28mm/190m long;available for aux. short jib application;

¡Mid-point link; requird when boom lengthexceeds 88.40m;

¡Boom skywalk(w/o stanchion); availablefor all sections of lificrane main boom.

See separate catalog, “SCX2800-2Luffing Towercrane Att.” with ref. no.0709(A)01T.EA131.

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 26: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

26

Standard equipment Optional equipment

Safety Devices ¡Load Moment Indicator; this is a computerizedautomatic over-load preventing system incl. totalsafe operation control system; provided with agraphic display panel indicating ten and some kindsof present lifting conditions;

¡Lifting height meter;¡Main and aux. drum pawl locks;¡Boom hoist drum pawl lock (w/automatic locking

device);¡Slewing lock;¡Slewing alarm;¡Travel alarm;¡Hook over-hoist limiting device;¡Boom over-hoist and -lowering limiting device;¡Secondry boom over hoist prient device;¡Boom backstops;¡Speed slowdown device;¡Boom angle indicator;¡Level gauge; fitted on floor of operator’s cab;¡Swing brake lamp;¡Warning lamps; avallable for pilot line;¡Swing brake safety circuit;¡Non-drum brake preventing device;¡Signal horn;¡Hook latch;¡Independent lever lock;¡Fool proof shut-off system;¡Engine monitoring lamps;¡Rear view mirrors;¡Free-fall interlocking device;¡Travel direction arrow;¡Front-end att. erection mode;¡Drum mirror;¡LMI safety circuit-off switch;¡Engine start interlock system.

¡Aux. hook over-hoist limiting device;¡Three color percentage indicator;¡Microphone & loud-speaker;¡Working light.

Followings are standard in case of luffing jibattachment:

¡Luffing jib angle detector;¡Luffing jib load detector;¡Luffing jib hook over-hoist limiting device;¡Luffing jib over-hoist and -lowering limiting

device;¡Luffing jib hoist drum pawl lock (if luffing jib

hoist drum is optionally provided);¡Luffing jib backstops;¡Secondry luffing jib over-hoist limiting device;¡Rear post backstops (hyd. cylinder type);¡Anemometer (recommend for tower crane

application);¡Cabin roof window guard;¡Aux. hook over hoisting limiter.

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 27: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

27

MEMO

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

Page 28: ASIAN ISSUE - (주)육천건설 · 2012-03-20 · Shoe width — 1,120mm wide as standard. Track adjustment — Manual adjustment device with oil jack and shim plate packs is standardized

• We are constantly improving our products and therefore reserve the right to change designs and specifications without notice.• Units in this specification are shown under International System of Units; the figures in parenthesis are under GravitationalSystem of Units as old one.

Address Inquires to:

SCX2800-2

Printed in Japan0903(A)01T.EA143

(Superedes 0709(A)05H.EA076)

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]