breakers schurter typ_t12-211
TRANSCRIPT
-
8/11/2019 Breakers Schurter Typ_t12-211
1/7www.schurter.com26
Produktebeschreibung
Der Gerteschutzschalter (CBE) der T12 Serie ist ein einpoligerberlast-Schutzschalter mit thermischer Auslsung. Er ist ein platz-sparender, kostengnstiger und zuverlssiger Schutzschalter mitpositiver Freiauslsung bei berlastungen und Kurzschlssen inner-
halb der maximalen Abschaltleistung. Er wird vor allem zumberstromschutz von Motoren, Transformatoren, Solenoids etc.eingesetzt.
Der speziell konstruierte und bewhrte Mechanismus ffnet die Kon-takte im Falle einer berlast. Ein Bimetallstreifen wird durch denberstrom erhitzt und bettigt den Auslsemechanismus. Die Kon-takte werden selbst dann geffnet, wenn der Einschaltknopf manuellin der Schliessposition gehalten wird. Dieses Verhalten nennt manpositive Freiauslsung. Die Kontakte werden durch einen Sprung-vorgang geffnet und geschlossen und die Ausschaltung ist durchdas Vorstehen des Einschaltknopfes ersichtlich. Nach einer Aus-lsung wird der Mechanismus erst dann verklinkt, wenn der manuelleEinschaltknopf zuerst vollstndig hinuntergedrckt und dann losge-lassen wird. Die Kontakte knnen nicht durch sanften Druck auf den
Einschaltknopf bei geringem Kontaktdruck geschlossen werden.
Die Zeit, welche verstreichen kann nachdem ein berstrom zufliessen beginnt, ist aus der Auslsekennlinie (der Auslsezone)ersichtlich. Sie gilt fr eine Raumtemperatur von +23C, ohneVorbelastung.
Ausfhrungs-Varianten
Flanschbefestigung Gewindehalsbefestigung Bettigungsarten: Reset- oder manuelles
Ein-/Ausschalten (Druck/Druck) Anschlsse: Flachstecker oder Schraubanschlsse Unabhngiger Hilfskontakt (Wechsler) Nebenanschluss Stellungsanzeige am Rckstellknopf visualisiert den Schaltzustand
Besondere Merkmale
Vorteilhafter Preis Flachsteckanschlsse Mehrere Montagearten Positive Freiauslsung Unempfindlich gegen Schock und Vibration UL, CSA, VDE und weitere Approbationen
Product description
A circuit breaker for equipment (CBE) of the T12 series is a singlepole, thermally operated device providing small size, low cost andreliable trip-free operation on overloads and short circuits, up to themaximum breaking capacity. It is intended primarily for protection
of motors, transformers, solenoids etc. against damage due to over-current conditions.
The well proven mechanism is designed to open the contacts in theevent of a current flow in excess of the time/current characteristic ofthe device. A bimetal strip is heated by the overcurrent and deflects,thereby releasing the latch mechanism. The contacts will open even ifthe reset button is manually held in the closed position. This is knownas the positively trip-free feature. The contacts open and close with asnap action and the tripped state is clearly shown by the increasedprojection of the reset button. After operation, the mechanism will notlatch closed until the manual reset button is fully depressed and thenreleased. It is impossible to tease the contacts by gentle pressureon the reset button.
The time which can elapse in case of an overcurrent is given bythe tripping characteristic (tripping zone). This curve is valid for adevice operating at an ambient temperature of +23C, withouthany preloading.
Available options
Flange type Threaded neck type Type of actuation: reset or manual ON/OFF (push/push) Terminals:
quick connect terminals screw clamp terminals
Independent auxiliary contact (change-over contact) Shunt terminal Setting indication on the reset button indicates the position
of the contacts
Special features
Competitive pricing Quick connect terminals Choice of mounting styles Positively trip-free Not affected by shock or vibration UL, CSA, VDE and other approvals
CIRCUIT BREAKERS FOR EQUIPMENTGERTESCHUTZSCHALTER T12
-
8/11/2019 Breakers Schurter Typ_t12-211
2/7www.schurter.com 27
BeispielNennstrom bei +23C 5,0 A Umgebungstemperatur +50CKorrekturfaktor 1,2Gewhlter Nennstrom bei+50C Umgebungstemperatur5,0 A x 1,2 = 6,0 A
Umgebungs- Korrekturfaktortemperatur [C]
-5 0,87
0 0,90
+10 0,95
+23 1,00
+30 1,05
+40 1,12
+50 1,20
+60 1,30
Einflu derUmgebungstemperatur
Die Eichung gilt fr eine Umgebungs-temperatur von +23C. Zur Bestimmung
des Nennstromes fr eine tiefere oderhhere Umgebungstemperatur ist einKorrekturfaktor gem untenstehenderTabelle zu verwenden:
Trippingtime/Auslsezeit
10'000
60
2`000
1`000
500
200
100
50
20
10
5
2
1
0,5
0,3
0,2
0,1
[ sec ][ min ]
10
5
1
30
20
1,05
Multiple of rated currentNennstrom-Vielfaches
[ x In ]
10854321,32
Rated current/ Nennstrom
< 7,0 A
7,0 A
Ambient temp.Umgebungstemp. +23 C
Technical data/ Technische Daten
Main circuit/ Hauptstromkreis:
Rated voltage Ue See approvals, page 28 AC 240 V; DC 28 VNennspannung Ue Siehe Approbationen Seite 28 AC 240 V; DC 28 V
Rated current In See approvals, page 28 AC/DC 0,05 16 A Nennstrom In Siehe Approbationen Seite 28 AC/DC 0,05 16 A
Conditional short circuit current Inc EN 60934PC1, AC 240 V 1000 A
Bedingtes Schaltvermgen Inc EN 60934PC1, AC 240 V 1000 A
Short circuit capacity Icn AC 240 V with In
-
8/11/2019 Breakers Schurter Typ_t12-211
3/7www.schurter.com28
Technical data (continued)/ Technische Daten (Fortsetzung)
Degree of protection Accessible range IP40Termination range IP00
Schutzgrad Bettigungsbereich IP40
Anschlubereich IP00
Dielectric strength Operating range AC 4000 VSpannungsfestigkeit Bettigungsbereich AC 4000 V
Insulation resistance DC 500 V >100 MIsolationswiderstand DC 500 V >100 M
Endurance Number of cycles at 6 x In (AC) R-type 40Number of cycles at In S-type 5000
Lebensdauer Anzahl Schaltspiele bei 6 x In (AC) R-Typ 40Anzahl Schaltspiele bei In S-Typ 5000
Permissible ambient temperature -5C to +60CZulssige Umgebungstemperatur -5C bis +60C
Vibration resistance IEC 60068-2-6, Test Fc, 10 g1 mm amplitude 5-60 Hz, 60-500 Hz
Schwingungsfestigkeit IEC 60068-2-6, Test Fc, 10 g1mm Amplitude 5-60 Hz, 60-500 Hz
Shock resistance IEC 60068-2-27, Test Ea 100 gStossfestigkeit IEC 60068-2-27, Test Ea 100 g
Type of actuation Reset type R Manual ON/OFF (push/push) S
Bettigungsart Reset Typ R Manuell EIN/AUS (Druck/Druck) S
Type of tripping Thermal TO Positively trip-freeAuslseart Thermisch TO
Positive Freiauslsung
Weight approx. 23 gGewicht ca. 23 g
Approvals/ Approbationen
Main circuit/ Hauptstromkreis Auxiliary circuit/ Hilfsstromkreis
EVD
Rated Rated Rated Rated Rated Ratedcurrent range voltage AC voltage DC current voltage AC voltage DCNennstrom- Nenn- Nenn- Nennstrom Nenn- Nenn-bereich spannung AC spannung DC spannung AC spannung DC
UL UL 1077 0,3 15 A 240 V 28 V 3 A 28 V
2 A 120 V
CSA CSA C22.2 235 0,3 16 A 240 V 28 V 1 A 240 V
VDE EN 60934 0,05 16 A 240 V 28 V 1 A 240 V 28 V
SEMKO EN 60934 0,3 12 A 240 V 1 A 240 V
NEMKO 0,1 16 A 240 V 1 A 240 V
DEMKO 0,05 16 A 240 V 1 A 240 VSEV EN 60934 0,05 16 A 240 V 28 V 1 A 240 V 28 V
CIRCUIT BREAKERS FOR EQUIPMENTGERTESCHUTZSCHALTER T12
-
8/11/2019 Breakers Schurter Typ_t12-211
4/7www.schurter.com 29
Order code/ Bestellcode
Basic type/ Grundtyp
T12 Single pole thermal overload protection switch, positively trip-freeEinpoliger thermischer berstromschutzschalter mit positiverFreiauslsung
Mounting style/ Montageart
1 Flange typeFlanschbefestigung
2 Threaded neck type 3/8 27 UNS 2 Awith hexagonal- and knurled nutGewindehalsbefestigung 3/8 27 UNS 2 Amit Sechskant- und Rndelmutter
Actuation type/ Bettigungsart
1 Reset type (R-type)Reset Typ (R-Typ)
2 Manual ON/OFF (push/push) (S-type)Manuell EIN/AUS (Druck/Druck) (S-Typ)
Terminal type/ Anschluart
1 6,3 x 0,8 mm quick connect terminals IEC 612106,3 x 0,8 mm Flachstecker IEC 61210
2 Screw clamp terminals*Schraubklemmen** Not available with S-auxiliary contact or N-shunt terminal* Nicht lieferbar mit den Bauform-Varianten S Hilfskontakt und N Nebenanschluss
Construction variants/ Bauform-Varianten *
S Auxiliary contact
HilfskontaktN Shunt terminal only for rated currents
-
8/11/2019 Breakers Schurter Typ_t12-211
5/7www.schurter.com30
Threaded neck type/ Gewindehalsbefestigung
Cut-outMontageffnung
9.6
8.9
16 16
Maximum torque 1,5 NmAnzugsdrehmoment max. 1,5 Nm
T12211
1 2
3/8-27UNS-2A
OFF/AUS
10
24.6
14.7
18
5.7ON
/OFF
11.5
48.5
+0.5
0.2
2
310.2
8.8
LabelEtikette
SW14
14.5
8.8
LabelEtikette
48.5
Maximum torque 1,5 NmAnzugsdrehmoment max. 1,5 Nm
1 2
3/8-27UNS-2A
OFF/AUS
101
4.7
18
5.7ON
/OFF
+0.5
0.2
2
57.5
57.5
2.520.224.6310.2
3
14.5
SW14
A 6.3
T12211SN
546
14.5
Maximum torque 1,5 NmAnzugsdrehmoment max. 1,5 Nm
1 2
3/8-27UNS-2A
O
FF/AUS
101
4.7
18
5.7
O
N
/OFF
48.5
+0.5
0.2
310.2
8.1
M 4
T12212
11.5
8.8
LabelEtikette
SW14
CIRCUIT BREAKERS FOR EQUIPMENTGERTESCHUTZSCHALTER T12
-
8/11/2019 Breakers Schurter Typ_t12-211
6/7www.schurter.com 31
Cut-outMontageffnung
50
17
4.5
11.5
LabelEtikette
310.2
11.5
1 2
48.5
+0.5
0.2
13.5
10.7
6
4
OFF/AUS
ON
/OFF 40
5.7
M 4
8
T12112
Installation from rear/ Montage von hinten
Installation from front/ Montage von vorne
11.5
LabelEtikette
11.5
T12111
1 2
24.6
48.5
+
0.5
0.2
2
310.2
13.5
10.7
6
4
OFF/AUS
ON
/OFF 40
5.7
50.0
17
5.7
6.3
170.2
11.5
LabelEtikette
T12111SN
11.5
1 2
57.5
13.5
10.7
6
4
OFF/AUS
ON
/OFF 40
5.7
48.5
+0
.5
0
.2
3
9
2.524.6310.2
50 4.5
17
8.6
56
4
Flange type/ Flanschbefestigung
17.5 17.5
4031
+1.0+0.2
12
4.5
17.5 17.5
20
40
4.5
12
3.0
CIRCUIT BREAKERS FOR EQUIPMENTGERTESCHUTZSCHALTER T12
-
8/11/2019 Breakers Schurter Typ_t12-211
7/7www.schurter.com32
Protective transparent coverDegree of protection IP54Schutzhaube transparentSchutzgrad IP54
TZZ01
Protective cover rear side IP41Schutzhaube hinten IP41
TZZ06
Schematic diagrams accessories colours/ Schaltbilder Zubehr Farben
ColoursFarben Black/ schwarz
Setting display R whiteStellungsanzeige R weiss
Nickel plated/ vernickelt
White label/ Etikette weiss
Black/ schwarz
Nickel plated/ vernickelt
Black galvanized/ brniert schwarz
1 23
2
AccessoriesZubehr
32
46
Schematic diagramsSchaltbilder
T12-... T12-...N T12-...S T12-...SN
55 4
62 32
1 1
2 3
1 4
62
1
21
16
CIRCUIT BREAKERS FOR EQUIPMENTGERTESCHUTZSCHALTER T12