cartes électroniques
TRANSCRIPT
CARTES électroniques Les documents relatifs aux cartes électroniques contenues dans le matériel fabriqué par nous ne sont qu'approximatifs et fournis à titre indicatif, étant donné que les cartes électroniques sont soumis à des changements ou mises à jour en temps. Nous n'assumons aucune responsabilité pour falsification d'étalonnage ou modifications non autorisées par nous, ou non faites par nos spécialistes.
Convel s.r.l. Via dei Tigli N° 3 20853 BIASSONO -MB- ITALY Tel. 039/492763 (4 linee r.a.) Fax 039/493125 e-mail: [email protected] internet: http://www.convel.com
Relè Multifunzione Programmabile Multifunctional programmable relay
Modello / Type: SRVT2 SRTE2 SRPG2 SRAE2
Caratteristiche generali modelli: All types general characteristics: SRVT2 Relè voltmetrico di minima o massima tensione, per sistemi in continua, provvisto di due contatti in scambio in uscita. Versione a due potenziometri................. Versione a un potenziometro.................. SRVT2 Low or high voltage relay, for direct current system, with two output changeover contacts Two-trimmer version................. One-trimmer version.................. SRTE2 Relè temporizzatore ritardabile alla eccitazione, per sistemi in continua e alternata,provvisto di due contatti in scambio in uscita. SRTE2 Time relay on delay, for direct current and alternate system, with two output changeover contacts. SRPG2 Relè sorvegliatore d'isolamento, per sistemi in continua,provvisto di due contatti in scambio in uscita. RPG2 Insulation monitoring relay, for direct current system, with two output changeover contacts. SRAE2 Relè amperometrico di minima o massima corrente,per sistemi in continua, provvisto di due contatti in scambio in uscita. SRAE2 Low or high current relay, for direct current system, with two output changeover contacts Fissaggio su omega 35mm Omega fixing 35mm
Caratteristiche Segnalazione/regolazioni: Characteristics Segnalisations/settings: Led verde ON/ Green led ON Segnalazione relè eccitato / Energised relay signalisation Aggancio/Switch ON Potenziometro per regolazione soglia d'intervento - aggancio Trimmer setting - switch on Sgancio/Switch OFF Potenziometro (se presente) per regolazione soglia d'intervento - sgancio Trimmer (if present) setting - switch off
100mm
120mm
ALTO/TOP - VISTA LATERALE/LATERAL VIEW
1 2 3 4 5 6 7 8 9 10
Caratteristiche Contatti: Contacts features :
Portata contatto relè Relay contact rating 2A @ 24Vdc
22mm
VISTA FRONTALE FRONTAL VIEW
1 2 3 4 5 6 7 8 9 10
Alimentazione Main supply
Tensione da controllare Voltage to be checked
Collegamenti per i modelli: Connections for types : SRVT2 SRPG2 SRAE2
1 2 3 4 5 6 7 8 9 10
Collegamenti per i modelli: Connections for types : SRVT2 SRTE2 SRPG2
Alimentazione Main supply
Convel s.r.l. Via dei Tigli N° 3 20853 BIASSONO -MB- ITALY Tel. 039/492763 (4 linee r.a.) Fax 039/493125 e-mail: [email protected] internet: http://www.convel.com
Scheda controllo corrente effetto di Hall Current Hall effect control card Modello / Type: µTA2
Caratteristiche generali: General Characteristics: Scheda controllo corrente effetto di Hall Current Hall effect control card
Versioni scheda disponibili: Card version available: Scheda con trasformatore effetto Hall Card with Hall effect transformer 100A - 200A - 500A 1000A (Trasformatore non montato sulla scheda-Transformer not mounted on the card)
VISTA DALL'ALTO / TOP VIEW
75mm
120mm
REV:01
Convel s.r.l. Via dei Tigli N° 3 20853 BIASSONO -MB- ITALY Tel. 039/492763 (4 linee r.a.) Fax 039/493125 e-mail: [email protected] internet: http://www.convel.com
Scheda regolatore SCR 1F/3F 1Ph/3Ph SCR regulation card Modello / Type: 0215 µXFB3
LED: Acceso Spento Flashing Lampeggio lento Lampeggio veloce
LD1 (giallo)
Carica a fondo Sistema in funzione Carica manuale Test batteria (Entrambi i led contemporaneamente) Guasto fusibile extrarapido
LD2 (rosso)
Scheda in blocco Sistema in funzione Comunicazione seriale Guasto hardware
LD3 (verde)
Sequenza fasi OK Frequenza OK
Sequenza fasi errata Frequenza OK
Sequenza fasi OK Frequenza errata
Sequenza fasi errata Frequenza errata
LED: On Off Flashing Slow blink Fast blink
LD1 (yellow)
Boost charge System in function Manual charge Battery test (Both leds simultaneously) Fault speed fuse LD2
(red) Card failure System in function Serial
communication Hardware fault
LD3 (green)
Phase sequency OK Frequency OK
Incorrect phase sequency Frequency OK
Phase sequency OK Incorrect frequency
Incorrect phase sequency Incorrect frequency
100mm
160mm
VISTA DALL'ALTO / THE TOP VIEW
LD3 Verde/Green
LD2 Rosso/Red LD1 Giallo/Yellow
Legenda Led / Led Legend : LD1 Giallo/Yellow - Stato di funzionamento / Operating status LD2 Rosso/Red - Stato di funzionamento / Operating status LD3 Verde/Green - Stato linea ingresso / Input line status
Condizione di funzionamento/Allarmi : Operating condition / Alarms :
INGRESSO 6 IMPULSI 6 PULSE GATES
GATES 12 IMPULSI
INGRESSO 12 IMPULSI 12 PULSE GATES
INGRESSO CORRENTI TA CURRENT TA GATES
SEGNALI AUSILIARI AUXILIARY SIGNAL
ALIMENTAZIONE SUPPLY
SERIALE DI COMUNICAZIONE SERIAL COMMUNICATION
Convel s.r.l. Via dei Tigli N° 3 20853 BIASSONO -MB- ITALY Tel. 039/492763 (4 linee r.a.) Fax 039/493125 e-mail: [email protected] internet: http://www.convel.com
190mm
300mm
VISTA DALL'ALTO/ON THE TOP VIEW
Scheda inverter Inverter card
Modello / Type: µINV1F
Legenda Led / Led Legend : LD1 Giallo/Yellow - Limitazione massima potenza / Limitation maximum power LD2 Rosso/Red - Sovraccarico / OverloadLD3 Verde/Green - Parallelo attivo / Parallel activeLD4 Verde/Green - Linea emergenza OK /Emergency line OKLD5 Verde/Green - Sincronismo OK / Synchronism OKLD6 Giallo/Yellow - Vedi Tabella LD6 / See LD6 Table LD7 Rosso/Red - Vedi Tabella LD7 / See LD7 Table LD8 Verde/Green - Power ON / Linea ON
Tabella LD6 / LD6 Table : LD6 Giallo/Yellow Lampeggio veloce (+ LD7 led rosso-lampeggio veloce) : Fusibile Guasto / fast blink (+ LD7 red led-fast blink) : Fuse Failure Lampeggio veloce (+ LD7 led rosso acceso) : Massima Corrente Uscita / fast blink (+ LD7 red led-on stable) : Maximum Output CurrentLampeggio : Sovraccarico / Blink : Overload Acceso : Minima/Massima Tensione Uscita / On : Low/High Output Voltage Spento / Off
Tabella LD7 / LD7 Table : LD7 Rosso/Red Lampeggio veloce : Guasto Hardware / Fast blink : Hardware Failure Lampeggio : Errore eeprom / Blink : eeprom errorAcceso : Blocco Scheda / ON : Card block Flash veloce : Indica Trasmissione/ricezione seriale / Fast flashing : Indicates Transmit/serial receiving
LD8 Verde/Green
LD5 Verde/Green
LD4 Verde/Green LD3 Verde/Green
LD6 Giallo/Yellow LD7 Rosso/Red
LD2 Rosso/Red LD1 Giallo/Yellow
Convel s.r.l. Via dei Tigli N° 3 20853 BIASSONO -MB- ITALY Tel. 039/492763 (4 linee r.a.) Fax 039/493125 e-mail: [email protected] internet: http://www.convel.com
scheda isolamento impulsi IGBT IBGT insulation pulse card Modello / Type: FISPW2
VISTA DALL'ALTO / ON THE TOP VIEW
Caratteristiche generali: General Characteristics: scheda isolamento impulsi IGBT IGBT insulation pulse card
50mm
170mm
Convel s.r.l. Via dei Tigli N° 3 20853 BIASSONO -MB- ITALY Tel. 039/492763 (4 linee r.a.) Fax 039/493125 e-mail: [email protected] internet: http://www.convel.com
Scheda isolamento impulsi 1F/3F insulation pulses 1Ph/3Ph card Modello / Type: 0714 µXFBI2
VISTA DALL'ALTO / ON THE TOP VIEW
Caratteristiche generali: General Characteristics: Scheda isolamento impulsi 1F/3F Insulation pulses card 1Ph/3Ph
75mm
140mm
Convel s.r.l. Via dei Tigli N° 3 20853 BIASSONO -MB- ITALY Tel. 039/492763 (4 linee r.a.) Fax 039/493125 e-mail: [email protected] internet: http://www.convel.com
scheda BY-PASS BY-PASS card
Modello / Type: 0596-BPSC5
VISTA DALL'ALTO / ON THE TOP VIEW
102mm
148mm
Legenda Led / Led Legend : LD1 Giallo/Yellow - sovraccarico / overload LD2 Verde/Green - sincronismo OK / synchronism OKLD3 Verde/Green - carico alimentato da inverter / load on inverterLD4 Rosso/Red - carico alimentato da rete / load on main supplyLD5 Verde/Green - senso ciclico e fasi OK ( solo per 3F) / main supply voltage and phases OK (3Ph only) LD6 Verde/Green - senso ciclico e fasi inverter OK ( solo per 3F) / inverter voltage cycle and phases OK (3Ph only)
Legenda Potenziometri / Trimmer Legend : RV1 - regolazione controllo tensione inverter / inverter voltage controller regulation RV2 - regolazione controllo tensione di rete / main voltage controller regulation RV3 - regolazione controllo corrente uscita / inverter current regulation
DIPSWITCH : SW1 ON = by-pass 1F / 1Ph by-pass OFF = by-pass 3F / 3Ph by-pass SW2 ON = 50 Hz OFF = 60Hz SW3 ON = controllo tensione rete / OFF = esclusione controllo tensione rete / main supply controlled main supply not controlled SW4 ON = ritardo contattore c.a. 5sec. / OFF = ritardo contattore c.a. 30sec. /
LD1 giallo/yellowLD2/3/5/6 verde/green LD4 rosso/red
RV3
RV1 RV2
SW1÷4
Convel s.r.l. Via dei Tigli N° 3 20853 BIASSONO -MB- ITALY Tel. 039/492763 (4 linee r.a.) Fax 039/493125 e-mail: [email protected] internet: http://www.convel.com
scheda COMANDO SCR BY-PASS DRIVER SCR BY-PASS card
Modello / Type: 0596-BPDRV
VISTA DALL'ALTO / ON THE TOP VIEW
60mm
125mm
Caratteristiche generali: General Characteristics: scheda comando SCR by-pass drive SCR By-pass card
Convel s.r.l. Via dei Tigli N° 3 20853 BIASSONO -MB- ITALY Tel. 039/492763 (4 linee r.a.) Fax 039/493125 e-mail: [email protected] internet: http://www.convel.com
Scheda 4 ingressi e 8 allarmi 4 inputs and 8 alarms card Modello / Type: µIO2
MORSETTIERA INGRESSO INPUT TERMINAL BLOCK
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
MORSETTIERA USCITA OUTPUT TERMINAL BLOCK
SW1 Selettore indirizzo scheda Card address selector
**ATTENZIONE** Nel caso di acquisto di una
scheda di ricambio, l’indirizzo di quest’ultima dovrà essere il medesimo della scheda che
andrà a sostituire. (Per impostare l’indirizzo agire sul selettore SW1)
**WARNING**
In case you purchase a new spare card,its address will have to be the same of the
card it replaces. (To set the address,work on
SW1 selector)
VISTA DALL'ALTO / TOP VIEW
Caratteristiche generali : General characteristics :
Scheda 4 ingressi 8 allarmi con led di segnalazione. 4 inputs 8 alarms card with led indicator.
Caratteristiche Contatti : Contacts features : Portata contatto relè 10A @ 24Vdc. Relay contact rating 10A @ 24Vdc.
Segnali morsettiera ingresso: Input signals: 1 GND 2 Ingresso 4- / input 4- 3 Ingresso 4+ / input 4+ 4 Ingresso 3- / input 3- 5 Ingresso 3+ / input 3+ 6 Ingresso 2 / input 2 7 Ingresso 1 / input 1 8 +24V 9 +24V NOTA/NOTE : I segnali d’ingresso sono programmabili, riferirsi allo schema funzionale per la relativa funzione. The input signal are programmable, refer to functional drawing for its function.
Contatti morsettiera uscita: Output contacts : NO C NC 1 2 3 Contatto allarme 1 / Alarm contact 1 4 5 6 Contatto allarme 2 / Alarm contact 2 7 8 9 Contatto allarme 3 / Alarm contact 3 10 11 12 Contatto allarme 4 / Alarm contact 4 13 14 15 Contatto allarme 5 / Alarm contact 5 16 17 18 Contatto allarme 6 / Alarm contact 6 19 20 21 Contatto allarme 7 / Alarm contact 7 22 23 24 Contatto allarme 8 / Alarm contact 8 NOTA/NOTE : I contatti d’uscita sono programmabili, riferirsi allo schema funzionale per la relativa funzione. The output contacts are programmable, refer to functional drawing for its function.
70mm
190mm
LED ACCESO RELE' ECCITATO - LED SPENTO RELE' NON ECCITATO LED ON ENERGIZED RELAY - LED OFF DE-ENERGIZED RELAY
1 2 3 4 5 6 7 8 9
SERIALE DI COMUNICAZIONE SERIAL COMMUNICATION