certificados para produtos em aço 10204.pdf
TRANSCRIPT
-
8/13/2019 Certificados para produtos em ao 10204.pdf
1/2
BRITISH STAINLESS STEEL ASSOCIATION
Making the Most of Stainless Steel
HOME CONTACT MEMBERS AREA
Follow us on Twitter
HOME ABOUT BSSA TECHNICAL HELP FIND A SUPPLIER NEWS TRAINING EVENTS BSSA MEMBERS CONTACT US
Home Technical Help Technical Library Standards, Specifications & Grades European Standardisation
TECHNICAL HELP
About S tain less Steel
FAQ
Technical L ibrary
Special Topics
Technical Enquiries
Featured Articles & Publications
Availability of Stainless Steel
Grades
Opportunities for Stainless
Steel in Renewable and Low
Carbon Energy Technologies
BSSA Guide to Stainless Steel
Specifications - 2010 Edition
Getting the Best out of
Stainless Stee l
Special Grades of Stainless
Steel - Where to Find Them
BSSA Understanding Stainless
Steel - New Centenary Edition
Duplex Stainless Steels - A
Simplified Guide
Fabricating Duplex Stainless
Steel
Importance of Surface Finishin the Design of Stainless
Steel
More Than Just Scratching the
Surface - A Practical Approach
to Surface Finish
The Then and Now of
Electropolishing
Structural Sections in Stainless
Steel
Stainless steel fasteners
European Standards -
Referenced Standards for
Stainless Stee l Products
European EN Standard Grade
Summary
Stainless Stee l Grades
Datasheets
Stainless Stee l Datasheets for
Tubular Products
Selection of stainless steels
for the food processing
industries
Stainless Stee l Pipe
Fabrication
Stainless Stee l in IndoorSwimming Pool Buildings
BSSA Stainless Steel Surface
Finishes Pack
BSEN 10204 test certificates for stainless steel productsIntroduction
In Germany inspection documents (certificate types) were originally specified in standard DIN 50049. The definitions ofmaterial testing and certificate types in DIN 50049 was adopted for European standard EN 10204, first published in 1991.Certificate types 2.1, 2 .2, 2.3, 3.1A, 3.1B, 3.1C and 3.2 were defined, closely following the definitions in the German standard.EN 10204 was revised in 2004 and published as BSEN 10204 in October 2004 with a simplified range of inspectiondocuments (certificate types).These now only include types 2 .1, 2.2, 3.1 and 3.2.Type 2.3 has been deleted.Type 3.1 replaces 3.1BType 3.2 replaces 3.1A, 3.1C and 3.2 of the previous edition.This reduced range o f op tions should be easier to understand and work with.When this standard and certificate type is shown, it only refers to the certificate type and not the steel standard. This should becovered separately eg BSEN 10088-2, for stainless steel sheet or plate type products
Test certi ficate standards and types
Each of the certificate types has a reference number, which has both its content and 'validation' requirements described in thestandard in Appendix A, Table A.1. These descriptions are sometimes a little difficult to interpret and need some additionalinterpretation. The table below shows the full range of current (C) and withdrawn (W) EN 10204 certificate types, with someinterpretation of what they cover. In any case of dispute however the descriptions given in Table A.1 of EN 10204:2004 shouldbe used.
Certificate
typeTitle Status
Summary of EN10204
requirementsNotes
2.1Declaration ofcompliance withthe order
CStatement of compliance with theorder by the manufacturer.
No test results shown.
2.2 Test report C
Statement of compliance with theorder by the manufacturer basedon non-specific inspections (tests)by the manufacturer.
Like the old BS1449 'Cast Test' certificate. Mechanical test sample results fromanother coil from same cast, manufactured by the same process route, can beused.
2.3Specific testreport
WWith mention of test results fromspecific inspection and testing
Batch test results needed on the certificate. Difficult to distinguish this from the3.1B type.
3.1 Inspectioncertificate
C Statement of compliance with theorder by the manufacturer withresults of specific inspection
Replaces 3.1B. Common certificate type issued for 'batch tested' material. Cert.
issued and signed by manufacturer's representative, who must be independentof the manufacturing department. Eg Inspection department or test housemanager/supervisor.
3.1AInspectioncertificate 3.1A
WWith mention of test results fromspecific inspection and testing
Batch test results. Cert. issued by independent inspector required by releasingauthority (eg TUV for German pressure vessels). Replaced by 3.2 in 2004
3.1BInspectioncertificate 3.1B
WWith mention of test results fromspecific inspection and testing
Batch test results. Cert. issued and signed by manufacturer's representative.Replaced by 3.1 in 2004
3.1CInspectioncertificate 3.1C
WWith mention of test results fromspecific inspection and testing
Batch test results. Cert. issued by independent inspector appointed by customer(eg Lloyds). Replaced by 3.2 in 2004
3.2Inspectioncertificate
CStatement of compliance withorder with indication of results ofspecific inspection
Batch test results. Cert. issued by both manufacturer's representative and anindependent inspector appointed either by the customer (cf withdrawn 3.1C) oran inspector designated by official regulations (cf withdrawn 3.1A). ie 3.2 nowcovers scope of both 3.1A and 3.1C of 1991 edition. This cover what is oftenreferred to as 'outside inspection'
When the 3.2 certificate type is requested the manufacturing mill may prepare a 3.1 type certificate to present to the 'outsideinspector' to use as a basis for preparing the independent 3.2 certificate. Only the 3.2 certificate is valid however for theordered requirements and to match the product marking and inspectors stamp.
top
Site Map Terms & Conditions Members Area
cle: BSEN 10204 test certificates for stainless steel products http://www.bssa.org.uk/topics.php?article=195
2 16-01-2013 22:59
-
8/13/2019 Certificados para produtos em ao 10204.pdf
2/2
British Stainless Steel Association (BSSA): registered in England and Wales as a private company limited by guarantee; registration no. 07547349Registered Office: Broomgrove, 59 Clarkehouse Road, Sheffield S10 2LE, United KingdomTel: +44 (0)114 267 1260 | Fax: +44 (0)114 266 1252 | Email: [email protected]
Copyright 2007-2012 British Stainless Steel Association
web design sheffieldby Llama Digital | Businessmagnet IAP Partner
cle: BSEN 10204 test certificates for stainless steel products http://www.bssa.org.uk/topics.php?article=195
2 16-01-2013 22:59