ch03cid installation

15
F2880_D09 CID OPERATING GUIDE 3. CID INSTALLATION 3.1 Preparation Required before CID Installation 3.1.1 Preparation In order to avoid unsteady operations, which may cause some failures, the following preparations are necessary before installing the CID: 1. Check hardware environment 2. Prepare CID installation disk (CD-ROM) 3. Setup display resolution, color number and appearance requirement 4. Install TCP/IP protocol 5. Specify IP address 6. Set PC LAN interface as 10M/Half. NOTE: If Network equipment is used between PC and NE, Network equipment Ether interface is change to 10/half . When PC or Router connnects to C-Node F port, the port for PC or Router need set to 10M half Duplex. 7. Set PC time 8. Install printer (if necessary) CID Installation 1

Upload: sctl05

Post on 18-Jul-2016

217 views

Category:

Documents


1 download

DESCRIPTION

Install

TRANSCRIPT

Page 1: Ch03CID Installation

F2880_D09CID OPERATING GUIDE

3. CID INSTALLATION

3.1 Preparation Required before CID Installation

3.1.1 PreparationIn order to avoid unsteady operations, which may cause some failures, the following preparations are necessary before installing the CID:

1. Check hardware environment

2. Prepare CID installation disk (CD-ROM)

3. Setup display resolution, color number and appearance requirement

4. Install TCP/IP protocol

5. Specify IP address

6. Set PC LAN interface as 10M/Half.

NOTE:If Network equipment is used between PC and NE, Network equipment Ether interface is change to 10/half. When PC or Router connnects to C-Node F port, the port for PC or Router need set to 10M half Duplex.

7. Set PC time

8. Install printer (if necessary)

3.1.2 Procedure

1. Check hardware environment (basic system requirements).

2. Check that the hardware environment satisfies the requirements shown in the section 2. About CID; 2.3 Requirements.

3. Prepare CID installation disk (CD-ROM).

4. Set display resolution, color number and appearance.

CID Installation1

Page 2: Ch03CID Installation

F2880_D09CID OPERATING GUIDE

Set resolution as 1024 * 768 or more and color number 256 or better.

5. Setup TCP/IP Protocols.

Check that TCP/IP protocol has been installed in the operating system. Select “Start -> Settings -> Control Panel -> Network and Dial-up Connections-> Local Area Connection” to open the Network dialog box (Figure 3-1). When a Network Neighborhood icon is prepared on the desktop, the Network dialog box can also be displayed by right-clicking this icon and select “Property” from the displayed menu.If there is no TCP/IP, select “Add -> Protocol -> Microsoft -> TCP/ IP” then add the TCP/IP protocol.

Figure 3-1. Setting Network Connection Protocol

6. Specify IP Address.

Select “TCP/IP” and click the “Property” button (or double-click TCP/IP) in the Network dialog box. TCP/IP property dialog box (Figure 3-2) will be displayed. Click IP Address tab and specify the IP address.

CID Installation 2

Page 3: Ch03CID Installation

F2880_D09CID OPERATING GUIDE

Figure 3-2. Specify IP address

7. Install Printer (if necessary).

Check that a printer has been installed in the operating system. Select “Start -> Setting -> Printer” to open the Printer dialog box (Figure 3-3). If no printer has been installed, double-click “Add Printer” then install the printer according to the printer installation wizard.

CID Installation3

Page 4: Ch03CID Installation

F2880_D09CID OPERATING GUIDE

Figure 3-3. Install Printer

This step is the end of the procdure.

CID Installation 4

Page 5: Ch03CID Installation

F2880_D09CID OPERATING GUIDE

3.2 Install CID

3.2.1 Task FlowThe CID is installed according to the following procedure:

1. Startup CID installation program.

2. Operate with CID installation wizard.

3. Enter user information.

4. Choose destination location.

5. Select components.

6. Select program folder.

7. Finish the installation and restart the computer.

3.2.2 Procedure

3.2.2.1 Startup Installation Program

1. Turn on the PC and startup the OS.

2. Close all other application programs, including varied tool item and background program (such as business application software).

3. Insert the installation disk (CID CD-ROM) into the CD-ROM drive. The installation wizard automatically starts up. Then go to Step 6.

If the installation wizard does not start, perform Steps 4 and 5.

4. Click the Start button in the lower left of the window to show the menu, and select Run. A dialog box with an entry field appears.

5. Enter the path in which the CID setup program exists (see the following example), then click the OK button.

5

Page 6: Ch03CID Installation

F2880_D09CID OPERATING GUIDE

Figure 3-4. Run Setup

6. The Setup dialog box shown in Figure 3-5 below appears, showing that all data required for CID installation is loaded automatically. After preparation is completed, the Welcome dialog box will appear to start the CID installation wizard.

Figure 3-5. Setup Diagram (Loading)

This step is the end of the procedure.

CID Installation6

Page 7: Ch03CID Installation

F2880_D09CID OPERATING GUIDE

3.2.2.2 Operate with CID Installation Wizard

After all the necessary data has been loaded, the CID installation wizard will start with the Welcome dialog box (Figure 3-6).

1. Click the Next button on the Welcome dialog box to proceed. The User Information dialog box will be displayed.

NOTE: Clicking the Cancel button quits the CID installation.

Figure 3-6. Welcome Dialog Box

2. In the User Information dialog box (Figure 3-7), enter user’s name, company name and the product serial number. Then click the Next button to proceed. The Choose Destination Location dialog box will be displayed.

The loading program will record your information.

7

Page 8: Ch03CID Installation

F2880_D09CID OPERATING GUIDE

Figure 3-7. User’s information Dialog Box

3. The Choose Destination Location dialog box (Figure 3-8) shows the destination folder to which the CID program is to be installed. The default directory is C:\CID.

Figure 3-8. Choose Destination Location Dialog box

CID Installation8

Page 9: Ch03CID Installation

F2880_D09CID OPERATING GUIDE

To change the default destination, click the Browse button to open the Choose Folder dialog box (Figure 3-9). Enter a desired destination location, then click the OK button to go back to the Choose Destination Location dialog box.

Figure 3-9. Choose Folder Dialog box

Confirm the destination location you have chosen, then click the Next button on the Choose Destination Location dialog box. The Select Components dialog box will be displayed.

4. In the Select Components dialog box (Figure 3-10), select the components to be installed by clicking the check box on the left of each component (leaving a tick). After selecting all components to be installed, then click the Next button. The Select Program Folder dialog box will be displayed.

NOTE: All components should be selected.

9

Page 10: Ch03CID Installation

F2880_D09CID OPERATING GUIDE

Figure 3-10. Select Component Dialog box

5. In the Select Program Folder dialog box (Figure 3-11), select the program folder in which the shortcut icon of the CID application software should be created and saved. You can select the default folder (named “CID”) or another existing program folder. It is also possible to prepare a new program folder by entering a new folder name in the Program Folders field.

After selecting (clicking) the program folder, click the Next button. The Setup Complete dialog box will be displayed.

10

Page 11: Ch03CID Installation

F2880_D09CID OPERATING GUIDE

Figure 3-11. Select Program Folder Dialog box

NOTE: Program folder means the menu item list, which can be seen by clicking “start” -> “program” on the system. Each program folder contains many program items, each of them is a functional program, and each application will be started up by selecting the corresponding the program in it.

11

Page 12: Ch03CID Installation

E

F2880_D09CID OPERATING GUIDE

3.2.2.3 Finish CID Installation

Installation program goes to general setting after the replication work of installation disk finished. Some information will automatically appear and disappear on the screen, and when all the settings have been completed, the Setup Complete dialog box (Figure 3-12) will be displayed.

Figure 3-12. Setup Complete Dialog box

Click the Finish button to complete the CID installation.

This step is the end of the procedure.

CID Installation12