check-q-meter fd · re 27551/12.2015, bosch rexroth ag features the check-q-meter is a leakage-free...
TRANSCRIPT
![Page 1: Check-Q-meter FD · RE 27551/12.2015, Bosch Rexroth AG Features The check-Q-meter is a leakage-free pilot operated check valve. It controls the returning flow V2q in relation to the](https://reader034.vdocuments.pub/reader034/viewer/2022042509/5f4dd193045b64163a4921ea/html5/thumbnails/1.jpg)
RE 27551/12.2015, Bosch Rexroth AG
FeaturesThe check-Q-meter is a leakage-free pilot operated check valve. It controls the returning flow qV2 in relation to the flow being directed into the opposite side of the actuator qV1. With cylinders the area ratio (qV2 = qV1 × ϕ) has to be taken into account.
▶ By-pass valve, free-flow in opposite direction ▶ Optional built-on secondary pressure relief valve (only
for valve with flange connections) ▶ For installation in manifolds (cartridge valve) ▶ With SAE flanged ports ▶ For sub plate mounting, porting pattern to
– ISO 5781-06-07-0-00 (size 12, 16) – ISO 5781-08-10-0-00 (size 25) – ISO 5781-10-13-0-00 (size 32)
▶ Use sub plate version when valve panel mounting
Fields of application ▶ Construction machinery ▶ Cranes ▶ Excavators ▶ Material handler ▶ Drilling rigs ▶ Stationary applications
▶ Sizes 12, 16, 25, 32 ▶ Series 2X ▶ Max. operating pressure 350 bar ▶ Max. flow 560 l/min
Check-Q-meterFD
RE 27551Edition: 12.2015Replaces: 06.2003
ContentsFunctional description 2Technical data 4Type code 5Characteristic curves 6Circuit examples 7Dimensions 8
![Page 2: Check-Q-meter FD · RE 27551/12.2015, Bosch Rexroth AG Features The check-Q-meter is a leakage-free pilot operated check valve. It controls the returning flow V2q in relation to the](https://reader034.vdocuments.pub/reader034/viewer/2022042509/5f4dd193045b64163a4921ea/html5/thumbnails/2.jpg)
Bosch Rexroth AG, RE 27551/12.2015
2 FD | Check-Q-meterFunctional description
Functional description
Check-Q-meters are used in hydraulic systems to influence the speeds of hydraulic motors and cylinders independent of the load (prevents running away). In addition there is an isolator function for pipe burst safety.The check-Q-meter comprises basically of the housing (1), main poppet (2), pilot part (3), pilot spool (4), damping spool (5) und pilot damping (6).
Lifting the loadWith free-flow from A to B the main spool (2) is opened. If the load pressure fails (e.g. pipe break between the direc-tional valve and ports A) then the main spool (2) immedi-ately closes. This function is achieved by the connection of the load side (7) with spring chamber (8).
Lowering the load (circuit examples)The direction of flow is from B to A. Port A is connected to tank via the directional valve. The piston rod side of the cylinder has a flow applied which corresponds to the work-ing conditions. The relationship between the control pres-sure at port X and the load pressure at port B = 1 : 20.When the control pressure is reached the pre-opening of the main spool takes place. Via the control spool (4) the pilot stage (3) is lifted off its seat and chamber (8) is decompressed via this drilling and port A to tank. At the same time the load pressure in port B is no longer applied to chamber (8), within the main spool. The main poppet (2) is thereby unloaded. The reverse side of the control spool (4) at the main poppet (2), lies against the collar of the damping spool (5).
The pressure required at port X to open B to A is now only influenced by the spring in chamber (9). The pressure required to begin opening the connection B to A is 20 bar; to fully open the connection up to 70 bar is required depending on the version.The opening cross-section for flow control increases pro-gressively. It is created by the successive opening of radial drillings in the bush and the main poppet (2) land.The relationship between the control pressure, cracking pressure and differential pressure determines the flow to the actuator via the connection of B to A. Thus uncon-trolled running away of the actuator is prevented.The controlled lowering procedure is not affected even if there is a pipe burst between the directional valve and port A.
Guidelines for influencing the opening and closing times of the check-Q-meter
▶ Throttling of the opening sequence is via orifice (6) in the control spool (4) and both sides of the damping spool (5). The orifice (6) is protected by sieves.
▶ The closing movement of the check-Q-meter is virtually un-throttled.
▶ When being used in conjunction with cylinders the control line to port X can be fitted with a throttle check valve (meter-out control) to influence the closing sequence.
▶ When being used in conjunction with motors a throttle check valve should not be fitted in the control line to port X. In this case it is recommended that the control times of the directional valve are influenced.
![Page 3: Check-Q-meter FD · RE 27551/12.2015, Bosch Rexroth AG Features The check-Q-meter is a leakage-free pilot operated check valve. It controls the returning flow V2q in relation to the](https://reader034.vdocuments.pub/reader034/viewer/2022042509/5f4dd193045b64163a4921ea/html5/thumbnails/3.jpg)
RE 27551/12.2015, Bosch Rexroth AG
Check-Q-meter | FD Functional description
3
▼ Cross section (example FD…FB2X/…V01)
A
B
X
M T
RR
6 9 2
4 7 8 15
3
1 Housing2 Main poppet3 Pilot part4 Pilot spool5 Damping spool
6 Pilot damping (orifice)7 Load side8 Spring chamber9 Spring
▼ Symbols
Without secondary pressure relief valve With secondary pressure relief valve
B
AX
B M
A
X
B M
A T
X
Valve type:FD 12 KA 2X/B03..FD 16 KA 2X/B03..FD 25 KA 2X/B04..FD 32 KA 2X/B06..
Valve type:FD 12 PA 2X/B03.. FD 16 PA 2X/B03.. FD 25 PA 2X/B04.. FD 32 PA 2X/B06..
FD 12 FA 2X/B03..FD 16 FA 2X/B03..FD 25 FA 2X/B04..FD 32 FA 2X/B06..
Valve type:FD 12 FB 2X/.B03..FD 16 FB 2X/.B03..FD 25 FB 2X/.B04..FD 32 FB 2X/.B06..
Ports
A Control block
B Consumer
T Tank
X Control port
M Measuring port
![Page 4: Check-Q-meter FD · RE 27551/12.2015, Bosch Rexroth AG Features The check-Q-meter is a leakage-free pilot operated check valve. It controls the returning flow V2q in relation to the](https://reader034.vdocuments.pub/reader034/viewer/2022042509/5f4dd193045b64163a4921ea/html5/thumbnails/4.jpg)
Bosch Rexroth AG, RE 27551/12.2015
4 FD | Check-Q-meterTechnical data
Technical data
General
Weight kg See page 8
Installation position Preferably upright (port X up)
Type of connection See page 8
Ambient temperature range θ °C −20 to +80
Priming (Standard) One-coat paint RAL 5010
Hydraulic
Maximum operating pressure at the port
A, X pmax bar 350
B pmax bar 420
Control pressure at the port
X pmin bar 20 to 70 (The cracking pressure depends on the valve type. Further information on request.)
pmax bar 350
Cracking pressure A to B p bar 2
Maximum setting pressure for secondary pressure relief valve
p bar 420
Maximum flow at the port
A, B Size 12 Size 16 Size 25 Size 32
qVmax l/min 80 200 320 560
Area ratio of the pre-opening Control surface=
1
Load surface 20
Hydraulic fluid Mineral oil (HL, HLP) according to DIN 51524, other hydraulic fluids, such as HEES (synthetic esters) according to VDMA 24568, as well as hydraulic fluids as specified in data sheet 90221, at request
Hydraulic fluid temperature range θ °C –20 to +80
Viscosity range ν mm²/s 10 to 800
Maximum admissible degree of contamination of the hydraulic fluid cleanliness class according to ISO 4406 (c)
Class 20/18/15, for this we recommend using a filter with a minimum retention rate of β10 ≥ 75
NoteFor applications outside these parameters, please consult us!
![Page 5: Check-Q-meter FD · RE 27551/12.2015, Bosch Rexroth AG Features The check-Q-meter is a leakage-free pilot operated check valve. It controls the returning flow V2q in relation to the](https://reader034.vdocuments.pub/reader034/viewer/2022042509/5f4dd193045b64163a4921ea/html5/thumbnails/5.jpg)
RE 27551/12.2015, Bosch Rexroth AG
Check-Q-meter | FD Type code
5
Type code
01 02 03 04 05 06 07 08
FD 2X / V *
Model01 Check-Q-meter FD
SIze02 Size 12 12
Size 16 16
Size 25 25
Size 32 32
Design03 Manifold mounting (cartridge valve) KA
SAE flange connections without secondary pressure relief valve FA
SAE flange connections with secondary pressure relief valve FB
Sub-plate mounting without secondary pressure relief valve PA
Series04 20 to 29 (unchanged installation and connection dimensions) 2X
Pressure range of the secondary pressure relief valve (Valve with SAE flange connections, code only for version FB)
05 Pressure setting up to 200 bar 200
up to 315 bar 315
up to 420 bar 420
Orifice diameter06 Without orifice B00
With orifice(other orifice diameters on request)
⌀ 0.3 mm sizes 12 and 16 B03
⌀ 0.4 mm size 25 B04
⌀ 0.6 mm size 32 B06
Sealing material07 FKM (fluoroelastomer) V
08 Further specifications in plain text *
![Page 6: Check-Q-meter FD · RE 27551/12.2015, Bosch Rexroth AG Features The check-Q-meter is a leakage-free pilot operated check valve. It controls the returning flow V2q in relation to the](https://reader034.vdocuments.pub/reader034/viewer/2022042509/5f4dd193045b64163a4921ea/html5/thumbnails/6.jpg)
Bosch Rexroth AG, RE 27551/12.2015
6 FD | Check-Q-meterCharacteristic curves
Characteristic curves
▼ Pressure differential Δp in relation to flow qv, measured at throttle position: B → A Throttle fully open (px = up to 70 bar)
40
35
30
25
20
15
10
5
0 80 160 240 320 400 480 560
1 2 3 4
Pres
sure
diff
eren
tial ∆
p [b
ar]
Flow qV [l/min]
▼ Pressure differential Δp in relation to flow qv, measured via the check valve: A → B
0
1 2 3 4
80 160 240 320 400 480 560
12
10
8
6
4
2
Pres
sure
diff
eren
tial ∆
p [b
ar]
Flow qV [l/min]
1 Size 122 Size 163 Size 254 Size 32
NoteCharacteristic curves measured at ν = 41 mm2 and θ = 50° C).
![Page 7: Check-Q-meter FD · RE 27551/12.2015, Bosch Rexroth AG Features The check-Q-meter is a leakage-free pilot operated check valve. It controls the returning flow V2q in relation to the](https://reader034.vdocuments.pub/reader034/viewer/2022042509/5f4dd193045b64163a4921ea/html5/thumbnails/7.jpg)
RE 27551/12.2015, Bosch Rexroth AG
Check-Q-meter | FD Circuit examples
7
Circuit examples
Differential cylinderFor safety reasons, always a closed centre directional valve should be used!
Hydraulic motor ▶ Internal control of the holding brake:
So that the holding brake can operate both of the direc-tion all valve ports have to be connected to port T in the neutral position.
▶ External control of the holding brake: For safety reasons, if the brake is externally unloaded then it is possible to use a closed center directional valve for the neutral position.
B
AX
B
AX
NoteTwo single check-Q-meters cannot be used to control two cylinders which are forced mechanically to move together, as synchronisation and the same pressure cannot be guaranteed in each cylinder.Therefore, the cylinders have to be equipped with two pilot operated check valves, type SL from Bosch Rexroth (see data sheet 21460 for size 6 or 21468 for size 10 to 32). The check-Q-meter is fitted in a common line.In this case, the load pressure must not exceed 200 bar because of the opening ratio of the SL valves!
Example:Load pressure at cylinder: 200 barArea ratio SL check valve: ¹/₁₁Cracking pressure spring FD valve: 20 bar
= 18.2 bar
B
AX
X X
Y
18.2 bar Cracking pressure SL valve
< 20 bar Cracking pressure FD valve200 bar
11
![Page 8: Check-Q-meter FD · RE 27551/12.2015, Bosch Rexroth AG Features The check-Q-meter is a leakage-free pilot operated check valve. It controls the returning flow V2q in relation to the](https://reader034.vdocuments.pub/reader034/viewer/2022042509/5f4dd193045b64163a4921ea/html5/thumbnails/8.jpg)
Bosch Rexroth AG, RE 27551/12.2015
8 FD | Check-Q-meterDimensions
Dimensions [mm]
Dimensions
▼ FD valve for manifold mounting (version KA)
G1/4
Ø25.1
B2
L12
L1
D3
ØD2+0.1
ØD1+0.2
30°
L1−0
.3
L10+0
.1
L2+0
.4
L3−0
.4
L7
L5±0
.2
L8
L6±0
.2
ØD
8
B1±
0.2
20°
25°
ØD6R2.5
R 2.5
ØD7+0.2
ØD4H8
B1±0.2
D9; T1
25°
ØD
8
L9
L4
ØD5
X
1
2
B
A
1
x
x
AØ0.05
Ay
yx
Rz16
Rz8
x
y
=
=
Type B1 B2 D1 D2 D3 D4 D5 D6 D7 D8 D9 T1 L1 L2 L3 L4 L5 L6
FD 12 KA 2X/... 48 70 54 46 M42 × 2 38 34 46 38.6 16 M10 16 39 16 32 15.5 50.5 60
FD 16 KA 2X/... 48 70 54 46 M42 × 2 38 34 46 38.6 16 M10 16 39 16 32 15.5 50.6 60
FD 25 KA 2X/... 56 80 60 54 M52 × 2 48 40 60 48.6 25 M12 19 50 19 39 22 65 80
FD 32 KA 2X/... 66 95 72 65 M64 × 2 58 52 74 58.6 30 M16 23 52 19 40 25 71 85
Type L7 L8 L9 L10 L11 L12 Valve fixing screws Tightening torque MT [Nm]
Weight [kg]
FD 12 KA 2X/... 3 78 128 2.3 191 65 4 pieces M10 × 70 DIN 912-10.9 69 2.8
FD 16 KA 2X/... 3 78 128 2.3 191 65 4 pieces M10 × 70 DIN 912-10.9 69 2.8
FD 25 KA 2X/... 4 105 182 2.3 253 75 4 pieces M12 × 80 DIN 912-10.9 120 5.6
FD 32 KA 2X/... 4 105 198 2.3 289 94 4 pieces M16 × 100 DIN 912-10.9 295 7.5
Pipe threads G according to ISO 228/1
1 Control port2 Name plate
Ports A and B can be optionally arranged about the circumference.Attention! The valve fixing holes must not be damaged.
Tightening torque MT of cartridge valve:
Size MA [Nm]
12, 16 65
25 110
32 270
![Page 9: Check-Q-meter FD · RE 27551/12.2015, Bosch Rexroth AG Features The check-Q-meter is a leakage-free pilot operated check valve. It controls the returning flow V2q in relation to the](https://reader034.vdocuments.pub/reader034/viewer/2022042509/5f4dd193045b64163a4921ea/html5/thumbnails/9.jpg)
RE 27551/12.2015, Bosch Rexroth AG
Check-Q-meter | FD Dimensions
9Dimensions [mm]
▼ FD valve for SAE flange connections, without secondary pressure relief valve (version FA)
1
2
3
4
65
7
56
G1/4
Ø25;1
ØD2
ØD1; T1
G1/
4
Ø25
;1
H1
B1
H2
L6
L2 ØD3 ØD4
B3 B
4
L1
L5
B1
L4
ØD5; T2
B2
L2
L3
A M
BX
M
B
(B)
AX
Type B1 B2 B3 B4 D1 D2 D3 D4 D5 H1 H2
FD 12 FA 2X/... 50.8 16.5 72 110 43 18 10.5 18 M10 36 72
FD 16 FA 2X/... 50.8 16.5 72 110 43 18 10.5 18 M10 36 72
FD 25 FA 2X/... 57.2 14.5 90 132 50 25 13.5 25 M12 45 90
FD 32 FA 2X/... 66.7 20 105 154 56 30 15 30 M14 50 105
Type L1 L2 L3 L4 L5 L6 T1 T2 Weight [kg] O-ring (5)
FD 12 FA 2X/... 39 23.8 105 65 140 78 0.1 15 7 25 × 3.5
FD 16 FA 2X/... 39 23.8 105 65 140 78 0.1 15 7 25 × 3.5
FD 25 FA 2X/... 50 27.8 148 75 200 105 0.1 18 16 32.92 × 3.53
FD 32 FA 2X/... 52 31.6 155 94 215 115 0.1 21 21 37.7 × 3.53
Pipe threads G according to ISO 228/1
1 Control port2 Measuring port3 Fixing screws1)
4 Blind flange1)
5 O-ring6 Port B (optionally)7 Name plate
SAE flange connection:Operating pressure 6000 PSI (420 bar)
1) Included within the scope of supply.
![Page 10: Check-Q-meter FD · RE 27551/12.2015, Bosch Rexroth AG Features The check-Q-meter is a leakage-free pilot operated check valve. It controls the returning flow V2q in relation to the](https://reader034.vdocuments.pub/reader034/viewer/2022042509/5f4dd193045b64163a4921ea/html5/thumbnails/10.jpg)
Bosch Rexroth AG, RE 27551/12.2015
10 FD | Check-Q-meterDimensions
Dimensions [mm]
▼ FD valve for SAE flange connections, with secondary pressure relief valve (version FB)
1
27
3 4
8
5
5
6
6
G1/4
Ø25;1
ØD2
ØD1; T1G
1/4
Ø25
;1
H1
H2
H3
L8
L2 ØD5 ØD6
B2
B4
L1
L6
B1
L5
ØD7; T3
L2
L3
B1
D4
ØD3; T2
B5
L7
L4
B3
A M
BX
M
B
(B)
AX
T
T
Type B1 B2 B3 B4 B5 D1 D2 D3 D4 D5 D6 D7 H1 H2
FD 12 FB 2X/... 50.8 47 16.5 72 110 43 18 34 G 1/2 10.5 18 M10 36 72
FD 16 FB 2X/... 50.8 47 16.5 72 110 43 18 34 G 1/2 10.5 18 M10 36 72
FD 25 FB 2X/... 57.2 80 14.5 90 132 50 25 42 G 3/4 13.5 25 M12 45 90
FD 32 FB 2X/... 66.7 80 20 105 154 56 30 42 G 3/4 15 30 M14 50 105
Type H3 L1 L2 L3 L4 L5 L6 L7 L8 T1 T2 T3 Weight [kg]
O-ring (5)
FD 12 FB 2X/... 118 39 23.8 105 141.5 65 162 38 78 0.1 1 15 9 25 × 3.5
FD 16 FB 2X/... 118 39 23.8 105 141.5 65 162 38 78 0.1 1 15 9 25 × 3.5
FD 25 FB 2X/... 145 50 27.8 148 198 75 225 50 105 0.1 1 18 18 32.92 × 3.53
FD 32 FB 2X/... 145 52 31.6 155 215 94 240 50 115 0.1 1 21 24 37.7 × 3.53
Pipe threads G according to ISO 228/1
1 Control port2 Measuring port3 Fixing screws1)
4 Blind flange1)
5 O-ring6 Port B (optionally)7 Secondary pressure
relief valve8 Name plate
SAE flange connection:Operating pressure 6000 PSI (420 bar)
1) Included within the scope of supply.
![Page 11: Check-Q-meter FD · RE 27551/12.2015, Bosch Rexroth AG Features The check-Q-meter is a leakage-free pilot operated check valve. It controls the returning flow V2q in relation to the](https://reader034.vdocuments.pub/reader034/viewer/2022042509/5f4dd193045b64163a4921ea/html5/thumbnails/11.jpg)
RE 27551/12.2015, Bosch Rexroth AG
Check-Q-meter | FD Dimensions
11Dimensions [mm]
▼ FD valve for sub-plate mounting (version PA)
1
2
34
7
5
6
G1/4
Ø25;1
G1/
4
Ø25
;1
4
Ø6
B1
B2
L1
L8
B3
L7
Ø11
L3
L4
H1
H2
H3
L5
L2
L6L1
M
B
X
MBAX
A
Type B1 B2 B3 H1 H2 H3 L1 L2 L3 L4 L5 L6 L7 L8
FD 12 PA 2X/... 66.7 85 70 85 42.5 70 31.8 7.2 – 35.8 42.9 73.2 65 140
FD 16 PA 2X/... 66.7 85 70 85 42.5 70 31.8 7.2 – 35.8 42.9 73.2 65 140
FD 25 PA 2X/... 79.4 100 80 100 50 80 38.9 11.1 – 49.2 60.3 109.1 75 200
FD 32 PA 2X/... 96.8 120 95 120 60 95 35.3 16.7 42.1 67.5 84.2 119.7 94 215
Type Ø A, B Valve fixing screws Tightening torque MT [Nm] Weight [kg] O-ring (4)
FD 12 PA 2X/... 16 4 pieces M10 × 100 DIN 912-10.9 75 9 21.3 × 2.4
FD 16 PA 2X/... 16 4 pieces M10 × 100 DIN 912-10.9 75 9 21.3 × 2.4
FD 25 PA 2X/... 22 4 pieces M10 × 120 DIN 912-10.9 75 18 29.82 × 2.62
FD 32 PA 2X/... 30 6 pieces M10 × 140 DIN 912-10.9 75 24 27.69 × 3.53
Pipe threads G according to ISO 228/1
1 Control port2 Measuring port3 Fixing pin4 O-ringFixing holes:
4 pieces for sizes 12, 16, 25 6 pieces for size 32
5 Not for sizes 12, 16, 256 Name plate
Porting pattern according to ISO 5781:
Size Code
12, 16 5781-06-07-0-00
25 5781-08-10-0-00
32 5781-10-13-0-00
0.01/100mm
Rmax4
Required surface finish of mating plugs
![Page 12: Check-Q-meter FD · RE 27551/12.2015, Bosch Rexroth AG Features The check-Q-meter is a leakage-free pilot operated check valve. It controls the returning flow V2q in relation to the](https://reader034.vdocuments.pub/reader034/viewer/2022042509/5f4dd193045b64163a4921ea/html5/thumbnails/12.jpg)
Bosch Rexroth AGMobile ApplicationsZum Eisengießer97816 Lohr am Main, GermanyPhone +49 9352 [email protected]
© This document, as well as the data, specifications and other information set forth in it, are the exclusive property of Bosch Rexroth AG. It may not be reproduced or given to third parties without its consent. The data specified above only serve to describe the product. No statements concerning a certain condition or suitability for a certain application can be derived from our information. The information given does not release the user from the obligation of own judgment and verification. It must be remembered that our products are subject to a natural process of wear and aging.
12
Bosch Rexroth AG, RE 27551/12.2015
FD | Check-Q-meter
Bosch Rexroth AGMobile ApplicationsZum Eisengießer97816 Lohr am Main, GermanyPhone +49 9352 [email protected]
© This document, as well as the data, specifications and other information set forth in it, are the exclusive property of Bosch Rexroth AG. It may not be reproduced or given to third parties without its consent. The data specified above only serve to describe the product. No statements concerning a certain condition or suitability for a certain application can be derived from our information. The information given does not release the user from the obligation of own judgment and verification. It must be remembered that our products are subject to a natural process of wear and aging.