datalogger 2867 ba mxl dash 100 eng

7/27/2019 Datalogger 2867 BA MXL Dash 100 Eng

1/10

Aim Srl.Via Cavalcanti, 820063 Cernusco S/N (MI)ItaliaTel. (+39) 02.9290571Fax (+39) 02.92118024

www.aim-sportline.com

MXL DashUSER GUIDE

Made in Italy


2/10

Thank You.

We would like to thank you for having

choosen our MXLDash, which we believe

be the successful completion of the acqui-

sition EVO4 data.

It will be useful in checking all possible pa-

rameters of your sport vehicle, on tracks

where you will race, and will give you valua-ble information about lap times, predictive

lap time, about satellites status in the EVO4

GPS receiver.

Please, don't forget to periodically check

www.aim-sportline.com you will find, as

always, continuous updates firmware of

your system and software for data analysis.

02 03

GETTING STARTED

INSTALLATION AND CONNECTION MXL DASH

CONFIGURATION OF MXLDASH

BUTTONS AND FIELDS

DATA SHEE T

04

08

12

14

18

MXL Dash


3/10

GETTING STARTED

04

MXL Dash Digital Dysplay

CAN Cable

Software Race Studio2 CD

MXL Dash kit includes.

1 2


4/10

GETTING STARTED

06 07

Diplay

Menu Pushbutton Mem Pushbutton

Remotable Connector CAN - Power Connection

Scroll Pushbutton View Pushbutton

Configurable Alarm Leds 1-2-3 Configurable Alarm Leds 4-5-6Gear Flashes

MXL Dash


5/10

How To install and

connect MXLDash.

MXLDash has to be connected via CAN bus

to your EVO4, whose firmware version

should be 43.03.17 or following.

Connection is via CAN cable, that you find

in the kit: just plug the connector into the

EXP EVO4 port.

CHAPTER 1 INSTALLATION AND CONNECTION MXL DASH

08 09

MXL DASH

Speed 1-2

Beacon ECU - CAN - RS232

Exp. RPM K/L line

GPS Input

GPS Antenna Input Analog Channel

USB

Status EVO4 Power Connec tion 8-18 VDC

EVO4


6/10

Please, check the firmware version of your

EVO4: connect it to PC via USB cable, run

the program Aim RaceStudio2 and press

Device Info pushbutton. (1)

CHAPTER 1 INSTALLATION AND CONNECTION MXL DASH

10 11

If the firmware is not adequate:

Enter into ww w.aim-sportline.com

Enter into Download Area Section

Select Firmware

Download EVO4 Firmup to your PC. (2)

Finally, run it and at the e nd of operations,

check that everything is correct.

MXL DASH

2

1


7/10

CHAPTER 2 CONFIGURATION OF MXL DASH

12 13

How to configure

MXLDash.

MXL DASH

MXLDash receives its configuration para-

meters from EVO4.

So, you are supposed to configure EVO4 in

order to make MXLDash properly working.

Select, therefore, in EVO4 configuration,

MXLDash as a display.

You will see the MXLDash image appearing.

and you have to define:

The R PM thre sholds to act ivate the Flash

Gear Leds.

The channels displayed in the two pages of

the dash.

The related short names to be displayed.

The channels associated with the alarm

Leds, as well as the threshold values to

which turn on the Leds themselves.

Any message that may appear at power on.

n ATTENTION!The RPM scale is configurable: the end of

scale depends upon the EVO4 configura-

tion.

By pressing "Transmit" pushbutton all con-

figuration parameters are sent to EVO4

MXLDash.


8/10

When you turn MXLDash on, the bottom

row shows a message about the status of

the satellites:

Using the MENU key you enter into the

local configuration menu, it is possible:

n Night Vision On/OffTurn the back light On/Off.

n Set Time: 24H / 12HDetermine whether the current time is

shown in European format (00:24)

and American (12:12 am 0:12 pm)

Press OK to change the time format.

n Set GPS MarkerSet the finish line point for the EVO4 GPS.

Press OK to set the actual point as finish

line.

CHAPTER 3 BUTTONS AND FIELDS

14 15

Buttons and fields in MXLDash.

MXL DASH

1

2

3

4

5

6

7

n Total RunningShow and clear the internal timer that is au-

tomatically incremented when the engine

is turned on.

Press OK to reset the counter.

n OdometerResettable odometerpress OKto reset the odometer.

n SN 12234 FW 52.02.01The last page shows information about yor

MXLDash: Serial Number and Firmware

version of system.


9/10

The VIEW button let you change the

data shown on the display, you can select:

n RPMn Speedn Battery Leveln Time and daten Odometern Actual rolling lap timen Predictive lap timen Previous lap time

The MEM pushbutton is used, after the

test, to see the most important data:

n Lap numbern Lap timenMaximum RPM and speed

CHAPTER 3 BUTTONS AND FIELDS

16 17

MXL DASH

The View and Mem Buttons.

Mem Pushbutt on Vie w Pus hb ut to n

1 2

CHAPTER MXL DASH DATA SHEET MXL DASH


10/10

CHAPTER 4 MXL DASH DATA SHEET

Our web site aim-sportline.com is constantly

updated.

We try to share with you our experiences

about our products and how to use them

in the tracks all over the world.

Please, constantly check it and download

the last versions of the firmware of your

products.

n Aluminium bodyn Grey back lightn 6 alarm leds

n 10 configurable gear flashesn Dimensions: 179 x 91 x 26 mmnWeight: 500 g

18 19

MXL Dash

MXL DASH

n 4 Pins binder 712 female connector(solder view)

datalogger 2867 ba mxl dash 100 eng

Documents