digital and analog communication system

1

Digital and Analog Communication System

2

References1. 《现代通信原理》曹志刚清华大学出版社2. 《通信原理》樊昌信国防工业出版社

Chapter One

3

Introduction

Chapter One

Why?

Information Age

Information Superhighway

4

Application

military application;

common application;

Chapter One

5

What is a communication system?

Communication systems is used to transmit information.

1.1 Introduction

6

Key conceptions or words

(1) Information;

(2) Message;

(3) Signal;

(4) Waveforms

1.1 Introduction

7

1 Jimes C.Maxwell （ 1864 ）

2 Heinrich Hertz （ 1887 ）

3 Claude E.Shannon (1948)

4.Winner

1.1 Introduction

8

Perspective of communication

Wire

optic-fiber and networks

wireless

1G->2G->3G->B3G

WLAN; MIMO and MIMO-OFDM, UWB, optic –wireless communication

1.1 Introduction

9

What must be considered when you design a communication system?

1. Selection of the information-bearing

waveform

2. Bandwidth and power of the

waveform

3. Effect of system noise on the received

information

4. Cost of the system

1.1 Introduction

10

1.2 Digital and Analog source and system

• The generation of communication system

Transmitter

Information input m(t)

Signal processing channel

Signal processing

Carrier circuits

Receiver

noise

Carrier circuits

Information output

11

1) signal processor

In analog system it may be an analog low-pass filter; In hybrid one, it may be analog-to-digital converter(ADC)

2)Function of signal-processing block in hybrid one

Source coding

Channel coding(adding parity and others)

3) Function of Carrier Circuits

modulation

Function of transmitter

12

1 ） Classification: wire and wireless

Wire channel including twisted-pair telephone line/Coaxial cables,waveguides and fiber-optic cables

Wireless channel having air,vacuum and seawater

2) Note: The general principles of digital and analog modulation apply to all types of channels, although channel characteristics may impose constraints that favor a particular type of signaling

Channel

13

The receiver takes the corrupted signal at the channel output and converts it to a baseband

signal that can be handled by the receiver baseband processor, and then the receiver

baseband processor estimate the source information and output the estimation result

Receiver

14

The goal is to design communication system that transmit information to the receiver with as little deterioration as possible while satisfying design constrains such as allowable transmitted energy,allowable signal bandwidth and cost.

In digital system measure of deterioration is taken to be bit error rate(BER),while in analog system the performance measure is usually taken to be the signal-to-noise ratio(SNR) at the receiver output.

Summary

15


• Model of analog communication system

Transmitting end

Information source

modulator channel

Demodu- lator

Sink Or(acceptant)

Receiving end noise

16

1.2 Digital and Analog source and system(model of digital communication system)

17

1 ） Relatively inexpensive digital circuits may be used2 ） Privacy is preserved by using data encryption3 ） Greater dynamic range is possible4 ） Data from different sources my be transmitted over a common digital transmission system

2 the advantage of digital system


18

5 ） Noise does not accumulate in

long- distance systems by repeater

6 ） Error in detected data may be

small, even in large amount of noise

on the received signal

7 ） Error may often be corrected

by the use of coding

2 the advantage of digital system


19

1)More bandwidth is required generally

2)Sychronization is required

3.Disadvantages of Digital communication


20

1.2 Digital and Analog source and system(classification of communication system)

according to physical properties of information :

Telephone /data /image and so on according to frequency :

baseband transmitting/ bandpass transmitting system according to transmitting medium :

wire /wireless according to multiplexing patterm:

Frequency division multiplexing access(FDMA)

Time division multiplexing access(TDMS)

Code division multiplexing access(CDMA)

21


• Classification of communication patterm

• Peer to peer communication :

simplex;

half duplex;

duplex

• Parallel transmitting communication

• Series transmitting communication

22

1. Key conception

Digital information source produces a finite set of possible messages. Such as typewriter and keyboard

Analog information source produces messages that are defined on continuum.

Digital communication system transfers information from a digital source to the intended receiver(sink)

Analog communication system transfers information from a analog source to the intended receiver(sink)


23

1) Deterministic waveform It can be modeled as a completely specified function of time

2) Random waveform(stochastic waveform)

It can not be completely specified as a function of time and must be modeled probabilistically

1) Example:

1.3 Deterministic and Random waveforms

)cos()( 00 tAt

24

1)Property of the book

a. from easiness to difficulty

b. from concept to performance analysis

2) Methods of learning it

a. reading it again and again

b. grasping the important concept

c. understanding the basic communication system by deriving some key formula

d. simulation using Matlab

1.4 The property of the book and methods of learning it

25

1. Information ContentIf the probabiltiy of transmitting jth message is Pj ， the information content sent from a digital source when it was transmitted is given by:

1.9 Information Measure

bitPP

I jj

j )(log)1

(log 22

26


From the definition, we have the following results:

1) The message that are less likely to occur provide more information

2) Information content depends on only the likehood of sending the message and does not depend on possible interpretation of the content as to whether or not it makes sense.

27

2 Unit of information


bitsPI jbitsj )(log2,

natsPI jnatsj )ln(,

HartleyPI jhartleyj )(log10,

1) Bits,Nats and Hartley

28

2 Unit of information


2) Relationship between Bit,Nat and Hartley

)2/(log

)2/(ln

10,

,,

hartleyj

natsjbitj

I

II

29

1) Definition

If there are m possible different source message in a digital source(m is finite), and Pj is the probabiltiy of sending the jth message, the entropy (also called average information) is:


bitsP

PIPHm

j jj

m

jjj

12

1)

1(log

3. Entropy for Digital Source

30

4 Example1-1: In a string of 12 symbols, where each symbol consistis of one of four levels, there are 412 different combinations (words), since each levels is equally likely, and all the different words equally likely. Thus Pj=(1/4)12,

And

Ij=log2(1/(1/4)12)=12log2(4)=24bits


31

5 Source Rate


Source Rate is defined as bitsT

HR

Example: A1-2 A telephone touch-tone keypad has the digits 0 to 9 with probability of sending being 0.099 each, plus “*” and “#” with probability of sending being 0.005 each. If the keys are pressed at a rate of 2keys/s. compute the data rate for this source.

Solution: bitsP

PIPHm

j jj

m

jjj

12

1)

1(log

keybits /38.3

005.0

1log)005.0(2

099.0

1log)099.0(10

2log

11010

10

Using define above, where T=1/2=0.5s/key, then:

sbitsT

HR /76.65.0/38.3

32

For digital systems, the optimum system might be defined as the system that minimizes the BER at the system output subject to constraints on transmitted energy and channel bandwidth. Thus bit error rate and signal bandwidth are of prime importance in this course.

1.10 Channel capacity

Shannon gives channel capacity as

N

SBC 1log2

33

1.10 Channel capacity

Where B is the channel bandwidth in hertz, S/N is the signal-to-noise power ratio at the input to the digital receiver. And showed that if the rate of information R(bits/s) was less than C,the BER would approach zero.

34

In analog system, the optimum system might be defined as the one that achieves the largest signal-to-noise ratio at the receiver output, subject to design constraints such as channel bandwidth and transmitted power.

Nyquist showed that if a pulse represents one bit of data, noninterfering pulse could be sent over a channel no faster than 2B pulses/s, where B is the channel bandwidth in hertz. That is now known as the dimensionality theorem.

1.10 Channel Capacity

35

Example SA1-3: A computer user plans to buy a higher-speed modem for sending data over his or her analog telephone line. The telephone line has a signal-to-noise ratio(SNR) of 25dB and passes audio frequencies over the range, from 300 to 3200Hz, Calculate the maximum data rate that could be sent over the telephone line when there are on errors at the receiving end.

Solution: In the term of a power ratio, the SNR=10(25/10)=316.2, the bandwidth is B=3200-300= 2900 Hz ， we get:

1.10 Channel Capacity

sbitsN

SBC /24097)2.3161(log29001log 22

Problem: Can a 28.8kbit/s modem work on this telephone line? And a 14.4kbits/s modem?

36

Problems: 1.5, 1.7, 1.9,1.10, 1.12 ,1.13 1.15

Reading: page 1-2, §1-2 , §1-3, §1-6 §1-9, §1-10

Homework

digital and analog communication system

Documents