Download - 09. Perhitungan Konstruksi Dasar.pptx
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
1/32
Agustus 2013
Jurusan Teknik Sistem Perkapalan
Fakultas Teknologi Kelautan ITS SurabayaTahun 2013-2014
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
2/32
Contents :
A. Single Bottom
1. Floor Plates
1.2.1. Floor Plates in the cargo hold area
1.2.3. Floor Plates in the peaks 2. Longitudinal girders 2.2.1. Centre girder
2.2.2. Side girder
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
3/32
B. Double Bottom
1. General 2. Centre girder 3. Side girder 4. Inner bottom 5. Double bottom tanks 6. Double bottom, transverse framing system
6.1. Plate floors 6.3. Watertight floors 6.4. Bracket floors 6.5. Brackets 6.6. Struts
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
4/32
7. Double Bottom, Longitudinal Framing System 7.2. Bottom and inner bottom longitudinals 7.3. Plate floors
7.4. Brackets 7.5. Longitudinal girder system
C. Bottom Structure in Machinery Spaces in way ofthe Main Propulsion Plant
1. Single bottom 2. Double bottom 3. Engine seating
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
5/32
1.2.1 Floor plates in the cargo hold area Floor plates fitted between after peak bulkhead and collision
bulkhead, the section modulus is not to be less than:
5
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
6/32
The depth of the floor plates is not less than:h = 55 B 45 [mm]hmin = 180 mm
In ship having rise of floor. At 0,1 l from the ends of thelength l where possible, the depth of the floor plate websshall not be less than half the required depth.
Ships having a considerable rise of floor, the depth of the
floor plate webs at the beginning of the turn of bilge isnot less than the depth of frame.
Web thickness is not be less than:
t = h/100 + 3 [mm]
6
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
7/32
.1 The thickness of the floor plates in the peaks is not to beless than:
The thickness, however, need not be greater than required
by B.6.2.1.critical plate thickness see next slide
7
1.2.3 Floor plates in the peaks
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
8/32
The thickness, however, need not be greater thenrequired by B.6.2.1 ( the thickness of plate floors) :
tpf = ( tm - 2,0 ) . k [mm] tpf 16,0 mm
tm = thickness of the centre girder according B2.2.2 (the thickness of the centre girder) B2.2.2. The thickness of the centre girder is not to be less then: within 0,7 L amidship:
tm = h/ha [h/100 + 1,0].k [mm], for h 1200 mm tm = h/ha [h/120 + 3,0].k [mm], for h > 1200 mm ha = depth of the centre girder as build [mm] tm =shall not to be less then t according to 7.5 :
t = (5,0 + 0,03L)k [mm], tmin = 6,0 k [mm]
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
9/32
.2The floor plate
height in the fore
peak above top of
the keel or stemshoe is not to beless then :
h = 0,06 H + 0,7
[m]
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
10/3210
The stern tube is to be serroundedby the floor plates or, when the
ships shape is too narrow to bestiffened by internal rings. Whereno sole piece is fitted the internalrings may be dispenced with.
.3 The floor plates in theafter peak are to extendover the stern tube (see
also sec.13.C.1.4):
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
11/32
2. General 2.1.1 All single bottom ships are to have a centre girder. Side girders shall not be installed where the breadth measured on
top of floors does not exceed 6 m.
One side girder when the breadth measured on top of floors doesnot exceed 9 m.
Two side girders when the breadth measured on top of floorsexceed 9 m.
2.1.2 For the spacing of side girders from each other and from thecentre girder in way of bottom strengthening forward seeSection 6, E.1. see next slide
2.1.3 The continuous (centre) and intercostal side girders are to extendas far forward and aft as practicable and stiffened at their upper edge.
11
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
12/32
1. Arrangement of floors and girders
1.1 For the purpose of arranging floors and girders the
following areas are defined: -forward of x/L = o,7 for L 100 m -forward of x/L = 0,6 + 0,001 L for 100m < L 150 m -forward of x/L = 0,75 for L > 150 m
1.3 In case of tranverse framing, the spacing of side girders isnot to exceed L/250 + 0,9 [m] , up to a maximum of 1,4 m
12
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
13/32
2.2.1 Centre girder The web thickness tw and the sectional area of the face plate Af within 0,7 L
amidships is not to be less than:
Towards the ends the thickness of the web plate as well as the sectional areaof the top plate may be reduced by 10 %. Lightening holes are to be avoided.
2.2.2 Side girders: The web thickness tw and the sectional area of the face plate Af within 0,7 L
amidships is not to be less than:
Towards the ends, the thickness of the web plate and the sectional area ofthe face plate may be reduced by 10%.
13
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
14/32
Lightening holes may be fitted in the platefloors. The length of lightening holes may not exceed 0,75 of
the depth of center girder. The depth of holes may not more than 0,5 of the
depth of floor.min 300 mm
The total length of lightening holes may not more
than 0,5 of the length of plate floor from centergirders to the margin plate.
The web of plate floor close to center girder may notless than 0,4 the depth of center girder.
14
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
15/32
2. Centre girder 2.2.1. The depth of the centre girder is not to be less then h = 350 + 45. B [mm] hmin = 600 mm 2.2.2. The thickness of the centre girder is not to be less then: within 0,7 L amidship: tm = h/ha [h/100 + 1,0].k [mm], for h 1200 mm tm = h/ha [h/120 + 3,0].k [mm], for h > 1200 mm ha = depth of the centre girder as build [mm] tm =shall not to be less then t according to 7.5 t = (5,0 + 0,03L)k [mm], tmin = 6,0 k [mm]
within0,15 L at the ends: te = 0,9 tm,
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
16/32
3. Side girders
3.2. The thickness of the side girder is not to be less then: t = h / (120.ha ). k [mm] h = depth of the centre girder [mm]
ha = depth of the side girder as build [mm]
ha = need not to be taken less then h to calculate t t = shall not be less then t according 7.5
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
17/32
4. Inner bottom
4.1. The thickness of the inner bottom plating is not to be less then: t = 1,1. a. p. k + tK [mm]
p = design pressure [kN/m] p is the greater of the following values: p1 = 10 ( T hDB ) p2 = 10. h, where the inner bottom forms a tank boundary p3 = Pi according to Section 4.C.2 (see next slide) h = distance from top of the overflow pipe to inner bottom [m] hDB = double bottom height [m] tK = corrosion additions according to section 3.K
(see next slide)
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
18/32
Sec.4.C.2. Load on inner bottom
pi = 9,81 G/V. h (1 + av ) [kN/m] G = mass of cargo in the hold [t] V = volume of the hold [m] h = height of the highest point of the cargo
above the inner bottom [m], assuming holdto be completely filled.
av = acceleration factor = F.m, see 4.C.1.1
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
19/32
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
20/32
(Penumpu tengah ,menerus)
Plate floor/Solid floor
(wrang pelat)
(Lunas pelat datar)
(Penumpu samping ,terputus)
(Wrang pelat)
Innerbottom frame /reverse frame(Gading alas dalam /gading balik)
Bottom frame(Gading alas )
/Open floor(Wrang terbuka)Keel plate
(Pelat lunas)
Innerbottom plating(pelat alas dalam)
Bottom plating(pelat alas)
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
21/32
6.2.1 The thickness of the plate floor is not to be less then Tpf = ( tm - 2). k [mm] tm = thickness of centre girder according to 2.2.2. The thickness is not exeed 16,0 mm
The web sectional area is not to be less then Aw = . T. l. e ( 1 2y/l ). k e = spacing of the plate floors [m] l = span between longitudinal bulkheads,if any [m] l = B, if longitudinal bulkheads are not fitted. y = distance between supporting points of the plate
floors,(ship sides, longitudinal bulkheads) and the sectionconsidered [m], not to be greater then 0,4 l.
= 0,5 for spaces which may be empty at full draught,e.g.machinery spaces, store rooms etc.
= 0,3 , elsewhere
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
22/32
The section modulus of the bottom and innerbottom frame is not to be less then
W = n. c. a. l. p. k [cm]
p = design load, as follows for inner bottom frames
p = pi according to Section 4.C.2
= p1 or p2 according to Section 4.D.1
= 10 ( ThDB) hDB = double bottom height [m]
The greater
value is tobe used
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
23/32
n = 0,44, if p = p2 = 0,55, if p = pi or p1 = 0,70, if p = pB
c = 0,6 where strut according to 6.6 are providedat l/2, otherwise c = 1,0. l = unsupported span [m] disregarding struts, if any
The bracket, in general, to be of the same thickness as theplate floors. Their breadth is to be 0,75 of the depth of thecentre girder as per 2.2. The bracket are to be flange attheir free edge, where the unsupported span of bottomframes exceed 1,0 m or where the depth of floors exceed
750 mm
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
24/32
At the side girders,bottom frame and inner bottom
frames are supported by flat bars having the same depthas the inner bottom.
The cross sectional area of the struts as Section 10.C.2 (Pillar scantlings)
The design force is to be taken
P = 0,5. p. a. l [kN] p = load according to 6.4.3
l = unsupported span according to 6.4.3.
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
25/3225
Plate floor(wrang pelat)
(Pembujur alasdalam)
(Pembujur alas)
Innerbottom plating(pelat alas dalam)
(Pelat lunas)
Plate floor(wrang pelat)
(Penumpu tengah,
menerus)
(Penumpu samping,terputus)
(Bracket)
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
26/32
7.2 Bottom and inner bottom longitudinals
The section moduli according to section 9.B.3 .1(Framing system)
Sec.9.B.3.1 :
The section modulus Wland shear area Alof
longitudinals is not to be less then:
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
27/32
See Sec.9 B.2. Definations
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
28/32
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
29/32
29Fig. 9.4 End attachment
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
30/32
Inner bottom longitudinal
Bottom plating
Plate floor,watertightfloor
Bottom longitudinal
Tank top / inner bottom plating
Brackets
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
31/32
-
8/14/2019 09. Perhitungan Konstruksi Dasar.pptx
32/32
7.3.4 The scantling of plate floors are to bedetermined according to 6.2 (Plate floors
scantlings in transverse framing system)see slide no.18 etc.