Download - AMP 3535-O Specsheet
84
STEPPERDRIVES
3535 O Step Motor Drive with OscillatorFull & Half Step3.5 amps, 35 VDC
Features
• DC bus voltage 12-35 VDC motor supply (includ-ing ripple)
• Switch selectable motor current from 0.4–3.5amps/phase
• Switch selectable full or half step• Automatic 50% idle current reduction• Optically isolated 5 VDC inputs, step, direction
and enable• Enable input to turn off current to the motor.• On-board oscillator generates step pulses and
accel/decel ramps• On-board trimpot or external speed adjustment• 122 watts of usable power• Screw terminal connectors• MOSFET, dual H-bridge, inaudible PWM amplifier• 3 state, pulse width modulated current control,
switching at 20–30 KHz.• Drives 4, 6 or 8 lead size 11, 14, 17 or 23 step
motors• CE compliant
Description
The 3535O step motor driver is a full or half stepdrive, step phase sequencer with MOSFET threestate switching amplifiers and optoisolated circuits.This drive has a built in ramping pulse generator(oscillator) with adjustable speed, acceleration anddeceleration. Oscillator speed range is 400–5,000Hz. Speed can be set from on-board trimpot or ex-ternal pot.
A jumper allows you to select the internal oscillator.In oscillator mode, the pulse input becomes a run/stop signal: when this signal is set high, the motoraccelerates to a preset speed and slews. Loweringthe input signal causes the drive to decelerate torest.
The amplifier regulates motor current by choppingat a constant, inaudible frequency. Phase current isselected from 32 levels by a DIP switch.
3535
O S
tep
Mot
or D
rive
with
Osc
illat
or
2.50"
3.75"
0.125"
3.00"0.25"
4.00"
0.15"
4x Ø.125
3.70"
1.50"
0.25"
.875"
2x Ø.125
MECHANICAL OUTLINE
Amplifier
step
direction
+5
extspeed
pot
1
StepSequencer
Oscillator
STEP/SLEW JUMPER
current setting
full step/half step
step
dir
acceldecel
speed adj
A+A–B+B–
tomotor
enable
OpticalIsolator
OpticalIsolator 12-35 VDC
OpticalIsolator
65
43
2
BLOCK DIAGRAM
Recommended motors for the 3535 O drive:
Size 11 Size 14 Size 17 Size 23———— ———— ———— ————HT11-012 5014-842 HT17-068 HT23-394HT11-013 HT17-071 HT23-397
HT17-075 HT23-400
ELECTROMATEToll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099www.electromate.com
Sold & Serviced By:
85
STEPPERDRIVES
3535 O Torque Curves
HT11-012 MOTORMotor Connection: 4 Lead BipolarDrive Setting: Full Resolution • 1.0 A/Phase
DynamicTorque(oz-in)
rev/sec0 5 10 15 20 25 30 35 400
5
10
35 V
HT11-013 MOTORMotor Connection: 4 Lead BipolarDrive Setting: Full Resolution • 1.0 A/Phase
DynamicTorque(oz-in)
rev/sec0 5 10 15 20 25 30 35 400
5
10
15
35 V
5014-842 MOTORMotor Connection: ParallelDrive Setting: Full Resolution • 1.0 A/Phase
DynamicTorque(oz-in)
rev/sec0 5 10 15 20 25 30 35 400
5
10
15
20
25
35 V24 V
HT17-068 MOTORMotor Connection: ParallelDrive Setting: Full Resolution • 1.3 A/Phase
DynamicTorque(oz-in)
rev/sec0 5 10 15 20 25 30 35 400
5
10
15
20
25
30
35 V24 V
HT17-071 MOTORMotor Connection: ParallelDrive Setting: Full Resolution • 1.7 A/Phase
DynamicTorque(oz-in)
rev/sec0 5 10 15 20 25 30 35 400
10
20
30
40
50
60
35 V24 V
HT17-075 MOTORMotor Connection: ParallelDrive Setting: Full Resolution • 1.7 A/Phase
DynamicTorque(oz-in)
rev/sec0 5 10 15 20 25 30 35 400
10
20
30
40
50
60
35 V24 V
HT23-394 MOTORMotor Connection: ParallelDrive Setting: Full Resolution • 2.8 A/Phase
DynamicTorque(oz-in)
rev/sec0 5 10 15 20 25 30 35 400
10
20
30
40
50
60
35 V24 V
HT23-397 MOTORMotor Connection: ParallelDrive Setting: Full Resolution • 2.8 A/Phase
DynamicTorque(oz-in)
rev/sec0 5 10 15 20 25 30 35 400
30
60
90
120
150
35 V24 V
HT23-400 MOTORMotor Connection: ParallelDrive Setting: Full Resolution • 2.8 A/Phase
DynamicTorque(oz-in)
rev/sec0 5 10 15 20 25 30 35 400
50
100
150
200
250
35 V24 V
ELECTROMATEToll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099www.electromate.com
Sold & Serviced By: