Download - Anritsu Understanding LTE
-
5/26/2018 Anritsu Understanding LTE
1/60
UnderstandingLTE
www.anritsu.com
-
5/26/2018 Anritsu Understanding LTE
2/60Understanding LTE
Table of Contents
Definition of FMC ................................................................................................................................................ 2
FMC motivations ................................................................................................................................................ 3FMC operator requirements ................................................................................................................................ 3
NGN network trend from a technical point of view ....................................................................................... 4
LTE/SAE introduction ........................................................................................................................................... 6
The technologies ................................................................................................................................................... 8
Bearer service architecture ................................................................................................................................. 13
LTE technology .................................................................................................................................................... 13
Multiple Input Multiple Output ......................................................................................................................... 17
LTE physical layer channel structure ................................................................................................................. 22Downlink physical channels ............................................................................................................. 22
Downlink physical signals ................................................................................................................. 23
Uplink physical channels ............................................................................................................. 23
Uplink physical signals ................................................................................................................. 23
LTE transport channel structure ...................................................................................................................... 24
Downlink transport channels .......................................................................................................... 23
Uplink transport channels ............................................................................................................. 24
LTE logical channel structure .......................................................................................................................... 25MAC scheduler ................................................................................................................................................. 27
Latency improvements within LTE ................................................................................................................... 28
LTE typical implementations ............................................................................................................................ 29
Self Optimising Networks (SON) ...................................................................................................................... 31
Impact on users of the technology ................................................................................................................... 33
Consumers ......................................................................................................................................... 33
Network operators .......................................................................................................................... 33
Testing challenges ............................................................................................................................................... 35RF testing .......................................................................................................................... 35
OFDM radio testing .......................................................................................................................... 35
MIMO testing ............................................................................................................................................... 38
L1 testing ............................................................................................................................................... 42
L2/L3 testing in LTE ............................................................................................................................................ 43
UE test loop modes ........................................................................................................................................... 44
Test requirements in SAE .................................................................................................................................. 45
3GPP references ............................................................................................................................................... 49
Appendix - Examples of LTE Release 8 downlink signals ....................................................................... 51
1
-
5/26/2018 Anritsu Understanding LTE
3/60w w w . a n r i t s u . c o m
The Mobile Communications industry is currently developing standards and solutions for the next steps
in the evolution of mobile networks. This introduction looks at the fundamental radio and network
technologies being introduced in these steps, and how this is aligned into the future Fixed Mobile
Convergence (FMC) of the Next Generation Networks
Fixed Mobile Convergence - Common network core, different access options.
Definition of Fixed Mobile Convergence (FMC)
The following definition of FMC is based on the ETSI FMC ad hoc workgroup documents:
Fixed and Mobile Convergence (FMC) is concerned with the provision of network and service
capabilities, which are independent of the access technique. This does not necessarily imply the physical
convergence of networks. It is concerned with the development of converged network capabilities and
supporting standards. This set of standards may be used to offer a set of consistent services via fixed
or mobile access to fixed or mobile, public or private networks.
An important feature of FMC is to allow users to access a consistent set of services from any fixed or
Service
Layer USMCharging
Other
Enablers
Messaging Content &
Application B2BControl
Internet
PSTN
PLMN
SIP
IP
Backbone
IP Access
Network
IP Access
Network
Core
Network
Access
Network
PacketDelivery ControlA-GW A-GW
MGWMSC
xDSL
WiMAX
WLAN
2/3G/HSPA/LTE
2
-
5/26/2018 Anritsu Understanding LTE
4/603 | Understanding LTE
mobile terminal, via any compatible access point. An important extension of this principle is related to
roaming; users should be able to roam between different networks and be able to use the same
consistent set of services through those visited networks as they have available in the home network.
This feature is referred to as the Virtual Home Environment (VHE).
FMC motivations
The motivation behind FMC is to provide users with easy to use and desirable services, and to enable
service providers to deliver this with cost effective networks. The user motivations are to enable more
convenience with a required list of services as follows:
Mobility of people and the need to communicate on the move is increased, and
therefore the demand for mobile communications Conventional fixed networks continue to serve the home or the office
Wide range of services within a uniform network and mobile connection is mostimportant
Terminal mobility allows the customer the use of his (personal) terminal, e.g. histelephone at any place, at home, in the office or en route even abroad
Service mobility provides for the customer a common set of services independent ofthe access type and location. The services should have the same look and feel evenin different networks
Personal mobility means reachability, in the sense that the customer is reachable withone number, his personal number, everywhere. He can define several reachabilityprofiles (private, office) and he can change his profiles, especially the terminal wherehe wants his calls to arrive, from any terminal
Fixed Mobile Convergence operator requirements
One of the key requirements to enable the vision of fixed mobile convergence is for convergence of
the infra-structure and the O&M systems. Where an operator may today provide customer with
multiple services (like fixed line voice and fixed line data to the home/office, mobile voice and data,
multimedia TV and cable, interactive gaming and content etc), the operator must maintain separate
management and control mechanisms for each service. A customer will still have a separate SIM card
for the mobile, smart card for the cable/satellite, and usually separate billing mechanisms for each
service.
To enable an operator to provide converged services, with a true triple play offering, requires
convergence of the core network, the data management, and customer care systems within the
network. The evolution of the Next Generation Network, and the development of future cellular mobile
networks, is towards providing the technical infrastructure and resources to enable this for service
providers and network operators.
-
5/26/2018 Anritsu Understanding LTE
5/604w w w . a n r i t s u . c o m
NGN network trend from a technical point of view
The basic trend of Next Generation Network is towards an all IP network, to provide a simple method
for extension of networks as growth demands increase, and to allow simple addition of newtechnologies to access the network. Traditionally, operators have built multiple networks to provide
multiple services to customers (e.g. fixed telephone network, cable TV network, mobile network, xDSL
data networks), but for the future we would aim for a single network that can provide all of these
functions in a simple way.
Technical challenges in converged networks
So we see that the core network for NGN is an all IP network. The development of IP protocols has
been supporting this requirement for some years now, and IPv6 has specifically included features that
enable this vision. These developments include increased address ranges to provide sufficientaddresses to support users with an individual unique IP address throughout the whole network, and to
provide QoS support that is necessary for mobile networks and the wide variety of applications and
services to be delivered in the network.
The mobile networks will be connected to the Core Network through the IP Multimedia Subsystem
(IMS). The IMS will provide the necessary mobility and routing management required by a mobile
network, and ensures that the core network sees the mobile network as another IP network. The core
network will not need to manage mobility, authentication or security control as the user changes access
technology in the mobile network. In todays network this is the case. For example, changing fromWLAN access to GPRS data card on a laptop requires full connection, registration and authentication
APPLICATIONS
TRANSPORT &
SESSION CONTROL
ANY
ACCESS
IMS/SIP
TERMINALS
Rich
Voice
GamingInformation
Video
IP/MPLS/IMS
WiFi/
WiMAXDSL/Cable
UMTS3G-4G
-
5/26/2018 Anritsu Understanding LTE
6/605 | Understanding LTE
on each network and then manual control to switch from one to the other. Even when the mobile device
supports both access technologies, the data flow can not be seamlessly handed over between the 2
access technologies with no user awareness of the change. The IMS allows this seamless handover
between multiple access technologies, including management of billing, authentication and securityaccess control. The IMS also uses Session Initiated Protocol (SIP) to allow fast connection between the
mobile device and the core network. This is a key technology to enable the mobile network to feel like
an IP network. Traditional wireless networks have an extended time period for initial set-up of a data
session (typically 1-15 seconds) where a fixed network would provide this in milliseconds. The mobile
networks are moving now to all IP so that they can be easily deployed in a mixed technology scenario,
and enable a simple management and maintenance requirement without needing many different
proprietary networks to be maintained.
The individual access technologies of the mobile networks are also evolving to provide higher data rates
and improved spectral efficiency. There is also diversification in the deployment scenarios for each
technology, so that an operator can mix multiple technologies into a single network to optimise network
resources for local requirements. Examples of this are the use of WLAN hotspots for short range static
users (e.g airport lounge), WiMAX for providing static wide area coverage, and HSPA for high speed
mobile access.
In the chart below we can see evolution of new key technologies in the mobile access network that are
developing to contribute towards this NGN vision.
Release of 3GPP specifications
1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011
W-CDMA
1.28 Mcps TDD
HSDPA, IMS
HSUPA, MBMS, IMS+
HSPA+ (MIMO, HOM etc.)
LTE, SAE
Small LTE/SAEenhancements
GSM/GPRS/EDGE enhancements
LTEAdvanced
Release 99
ITU-R M.1457IMT-2000 Recommendations
Release 4
Release 5
Release 6
Release 7
Release 8
Release 9
Release 10
-
5/26/2018 Anritsu Understanding LTE
7/606w w w . a n r i t s u . c o m
Having considered the overall NGN network requirements, and the top level technology and user
requirements for this, we will now look at the evolution of the 3GPP network for mobile
communications.
LTE/SAE Introduction
Release 7 of 3GPP includes study items to introduce MIMO and 64QAM as transmission technologies
to increase data rate of the air interface, and IMS phase 2 introduces all IP network capability. This will
reach the practical limits in data rates and capacity for the existing 3G networks based on 5 MHz
W-CDMA technology. Release 7 has been deployed as an upgrade for existing HSPA networks, and is
sometimes called HSPA+, or HSPA Evolution. Beyond here W-CDMA is still evolving in Release 8
and later, using multi-carrier technologies to increase data rates, and further improvements in signalling
to increase data rates and reduce latency.
To move past the limitations of a 5 MHz W-CDMA system, 3GPP is now deploying a new standard for
a new mobile networks, and this is called the Long Term Evolution (LTE) and System Architecture
Evolution (SAE) for next generation mobile networks. This is the next step in the continuous move to
wider bandwidth and higher data rates. LTE and SAE are specified within 3GPP as part of the Release
8 version of specifications within the 36.xxx series of specifications. LTE will be a new evolved radio
interface and access network (E-UTRAN Evolved Universal Terrestrial Radio Access Network), but will
co-exist with W-CDMA (UTRAN) that will also continue to evolve within 3GPP. The overall description
for LTE/SAE is in TS 36.300, and the architecture description is in TS 36.401. E-UTRAN will also further
evolve in 3GPP Release 9, and then into IMT-Advanced as Release 10 & Release 11 for data rates
towards 1 GB/s.
The physical layer specification for LTE consists of a general document (TS 36.201), and four documents
(TS 36.211 through 36.214). The relation between the physical layer specifications in the context of the
higher layers is shown below.
To/From Higher Layers
36.214Physical layer -
Measurements
36.212Multiplexing andchannel coding
36.211Physical Channels
and Modulation
36.213Physical layer
procedures
-
5/26/2018 Anritsu Understanding LTE
8/607 | Understanding LTE
TS 36.201: Physical layer general descriptionThe contents of the layer 1 documents (TS 36.200 series); Where to find information;general description of LTE layer 1.
TS 36.211: Physical channels and modulationTo establish the characteristics of the layer-1 physical channels, generation of physicallayer signals and modulation.Definition of the uplink and downlink physical channels; The structure of the physicalchannels, frame format, physical resource elements, etc.
TS 36.212: Multiplexing and channel codingTo describe the transport channel and control channel data processing, includingmultiplexing, channel coding and interleaving.
TS 36.213: Physical layer proceduresTo establish the characteristics of the physical layer procedures.
TS 36.214: Physical layer measurementsTo establish the characteristics of the physical layer measurements.
As we discussed above, the purpose of LTE/SAE is to support the NGN, and Fixed Mobile
Convergence through the IP Multimedia Sub-system. For the user, this means to provide an always
connected high speed user experience, to feel just like an ADSL home network, but in a mobile
environment. For the operator/service provider, this means to provide an integrated network that is
simple and cost effective to deploy, and allows integration to the core network for customer care, billing,and management of the network.
So the key challenges are:
Data rates to true xDSL rates (e.g. 25-100 Mb/s given by VDSL2+ technology).
Connection set-up time, must give an always connected instant feel.
Seamless integration of Internet applications, unaffected by carrier technology.
A cost effective network infrastructure, and attractive user terminals.
As the future networks are integrated into a single IP network, so they offer different types of services
across a single network, and there is a requirement to differentiate the types of services and the
demands they place on the network. One of the key requirements is to be able to specify the Quality
of Service (QoS) requirements for the different services. This allows the mobile network to be configured
according to user/application requirements. The QoS will indicate to the network how to prioritise
different data links to users across the network, and how to manage the capacity so that all users and
applications are able to operate correctly. Typically, the QoS may be specified as a required or minimum
data rate, and required error control and re-transmission procedures. In the table below we can seesome examples of types of services, and the corresponding requirement s they have on the QoS and
latency in the network.
-
5/26/2018 Anritsu Understanding LTE
9/608w w w . a n r i t s u . c o m
The technologies
The two technologies we will consider are LTE (Long Term Evolution) and SAE (System Architecture
Evolution). These two technologies address the future requirements of the radio access network (RAN)
and core network (CN) respectively in the mobile network. These have now become known as the
Evolved Universal Terrestrial Radio Access Network (E-UTRAN) and Evolved Packet Core (EPC).First we will look at the SAE aspects, to understand the overall architecture of the new network and
technology, and then we will look more closely at the LTE radio network.
SAE technology
SAE is the network architecture and design to simplify the network and provide seamless integration
of the mobile network to other IP based communications networks. SAE uses a new evolved Node B
(eNB) and Access Gateway (aGW) and removes the RNC and SGSN from the equivalent 3G network
architecture, to make a simpler mobile network. This allows the network to be built as a flat all-IPbased network architecture. SAE also includes entities to allow full inter-working with other related
Wireless technologies (WCDMA, WiMAX, WLAN etc.). These entities can specifically manage and
permit the non-3GPP technologies to interface directly into the network and be managed from within
the same network.
As a reference, we can look at an existing 3G network architecture, shown below. First of all, we can
notice that this is shown with only the packet network included, as the SAE will be only packet based.
A full 3GPP network today includes a circuit switched network. This circuit switched element is an
evolution of the original GSM voice network architecture from the 1990s. One objective of NGN wasto move away from this old legacy network into a single all IP network using VoIP technology to provide
voice services, rather than a separate circuit switched network.
Class of service Bandwidth Latency QoS Requirement Example
Conversational Low-medium Low Guaranteed VoIP/Video calling
Streaming High Low Guaranteed IPTV, multi-media streaming
Browsing Low-medium Normal Best Effort Web browserBackground Medium Normal Minimal Email synchronisation
Broadcast High Low Guaranteed Multi-cast
-
5/26/2018 Anritsu Understanding LTE
10/609 | Understanding LTE
This old packet network is based around the GGSN (gateway to external networks) and the SGSN
(managing mobility and routing within the wireless network). There is no direct link from this network
through to any other network that may be used as a complementary access technology. So, to link
through to a WLAN or WiMAX network requires connection through either the public network (PDN)or through some proprietary IMS sub-system that an operator may implement for his own network.
Either way, this does not provide a simple and extendable architecture that can meet the future needs
of wireless communications.
BTS
BTS
BSC MGW
SMSC
MSC Server
VLRMSC
Server
MGW
HLR
AUC
GGSNIP
SGSN
Node B RNC
Node B RNC
GERAN CS-Core
UTRAN
PS-Core
Abis
A
Gb
lub
lur
lu PS
lu CS
Mc
Nb
Nc
Gr
Gn Gi
Mc
Gs
PSTN/
PLMN
UE
GERAN
UTRAN
Evolved RANMMEUPE
SAEAnchor
IASA
GPRS Core
non 3GPPIP Access
WLAN 3GPPIP Access
Evolved Packet Core
PCRF
HSS
Op. IPServ. (IMS,PSS, etc...)
SGSN
3GPPAnchor
Gb
lu
S3S4
S7
S1
S2 S2
S5a S5b
SGi
S6
Rx+
Greyindicates new functional
elements / interface
-
5/26/2018 Anritsu Understanding LTE
11/6010w w w . a n r i t s u . c o m
3GPP Anchor - The 3GPP Anchor is a functional entity that anchors the user plane for mobility between
the 2G/3G access system and the LTE access system.
SAE Anchor - The SAE Anchor is a functional entity that anchors the user plane for mobility between
3GPP access systems and non-3GPP access systems.
For the future SAE, we can see that it consists of an Evolved Packet Core (EPC), which is simplified when
compared to existing 3GPP networks, and has specific functions built in that allow direct connection
and extension to other wireless networks. The S2 interface allows operators to extend the network to
other IP based access technologies whilst still managing the critical functions like mobility, hand-over,
billing authentication and security within the mobile network. The EPC uses the S1 interface to
connect to the wireless radio access network (LTE), and the S3 interface to connect data through to
the SGSN to support handover to older 3GPP GPRS networks.
The EUTRAN network is broken down into two physical elements, the eNB and the aGW. This is
considerably simpler than the previous 3G networks, with the equivalent to the RNC now being
completely removed. Most of the flow control and data management functions of the RNC are now
located in the eNB. The eNB is able to manage all transmission related issues at the transmit site, for
faster re-transmission and link adaptation control. Previously these controls were passed through the
network for the RNC to manage, and this would create additional round-trip delays. This allows for
faster response time (e.g. for scheduling and re-transmissions) to improve latency and throughput of
the network. The aGW manages all mobility and routing through the network, and also the link through
to the authentication and billing databases.
LTE radio access networks - Physical Elements
E-UTRAN EPC
-
5/26/2018 Anritsu Understanding LTE
12/6011 | Understanding LTE
The previous diagram shows the physical breakdown in of the network functionality into the eNB and
the EPC (Evolved Packet Core). The EPC consists of a Gateway controller section that acts as a pipe to
transfer user data between the eNB and the external network, and a Mobility Management section that
manages mobility and routing of the data into the appropriate eNB. Here we can see the functions ofthe old NodeB and RNC now included into the eNB. On the right side of the diagram the basic protocol
stack for user plan and control plan signalling is shown.
On the next diagram we can see the breakdown of the various elements in the protocol stack, showing
the separation between eNodeB and MME, and the differences between User Plane and Control Plane
signalling. We can see that in both case the full signalling up to PDCP layer takes place between UE
and eNodeB. This is a key difference from previous networks, where the higher layer signalling was
relayed back through the network to other network elements such as an RNC or MSC. This change
means that the response to signalling is much faster as signals are not relayed through the network, and
this contributes a significant amount to the reduced latency in LTE/SAE networks.
New Radio Access Network - Protocol Elements
The logical breakdown of functions is shown in the next diagram. It is seen that the aGW can supportmultiple eNBs across multiple S1 interfaces, so the aGW control plane will be responsible for mobility
in the network. When looking at the logical elements in the network, we see two key elements in the
NAS
PHY
MAC
RLC
RRC
PDCP
UE
PHY
MAC
RLC
PDCP
UE
PHY
MAC
RLC
RRC
eNB
PHY
MAC
RLC
eNB
NAS
PDCP
aGW
PDCP
aGW
U-plane Protocol Stack
C-plane Protocol Stack
User Plane
- RLC and MAC sublayers (terminated in the eNB
on the network side) perform the functions such as:
- Scheduling; ARQ; HARQ
- PDCP sublayer (terminated in aGW on the network
side) performs for the U-plane the functions such as:
- Header compression;
- Integrity Protection (to be determined during WI phase)
- Ciphering
C Plane
- RLC and MAC sublayers (terminated in eNB on the
network side) perform the same functions as for the
U-plane;
- RRC (terminated in eNB on the network side)
performs functions such as:
- Broadcast; Paging; RRC; connection management;
- RB control; Mobility functions; UE measurement
reporting and control.
- PDCP sublayer (terminated in aGW on the network side) performs for the C-plane functions such as:
- Integrity Protection; Ciphering.
- NAS (terminated in aGW on the network side)
performs among other things:
- SAE bearer management; Authentication;
- Idle mode mobility handling;
- Paging origination in LTE_IDLE;
- Security control for the signalling between aGW
and UE, and for the U-plane.
-
5/26/2018 Anritsu Understanding LTE
13/6012w w w . a n r i t s u . c o m
aGW, these are the User Pane Entity (UPE) and the Mobility Management Entity (MME).
LTE Radio Access Network - Logical Elements
The MME is responsible for managing the eNBs and distributing paging messages to them. This allows
for management of mobility in the network, through the correct distribution of paging messages to
locate and provide data control information to the relevant users and the respective eNBs they are
connected to. The UPE is responsible for the routing and delivery of the user data to/from the correcteNBs. This means that the user data IP headers and routing will be managed here, to ensure that data
flows to the correct eNB and with the correct information for end user ID, QoS etc that are required by
the eNB scheduling algorithms.
The UPE will also provide termination of the protocol stack for paging messages coming from a user
through the eNBs. This is because paging messages are related to mobility and access requests within
the mobile network, and are not related to data that is passed out of the network to an external
application. So there must be correct termination of the protocol stack to permit the functions to work.
As the mobility and admission control is managed from the aGW, the protocol stack for these functionsis terminated here.
In Release 10 (LTE-Advanced) there are also two additional eNb types introduced, the indoor eNB and
the Home eNB (HNB). The HeNB also introduces a specific gateway element, the HeNB GW, that is
adapted to handle the high number of HeNB that are expected to be handled by such a system. The
HeNB has three modes of operation Closed, Hybrid or Open mode. In Closed mode, only the
subscribers that are specifically permitted to use that eNodeB (e.g. the people living at that house) can
access the eNodeB. This is called the Closed Subscriber Group (CSG) and is a defined list of users. In
Hybrid mode then both CSG and non CSG users can access the eNodeB, but priority is given to CSGmembers. In Open mode, the eNodeB is open to all subscribers to connect to it.
The eNB hosts the following functions:
Functions for radio resource management; radio bearer control,radio admission control, connection mobility control, dynamicallocation of resources to UEs in both uplink and downlink (scheduling);
IP header compression and encryption; Routing of user plane data towards server gateway;
Measurement and reporting for mobility and scheduling.
The MME hosts the following functions:
NAS signalling; -NAS signalling security; AS security control; Inter CN node signalling for mobility between 3GPP access networks; Idle mode UE reachability
The Serving Gateway (S-GW) hosts the following functions:
The local mobility anchor point for inter-eNB handover; Mobility anchoring for inter-3GPP mobility; E-UTRAN idle mode downlink packet buffering and initiation of network
triggered service request procedure; Transport level packet marking in the uplink and the downlink
the PDN Gateway (P-GW) hosts the following functions:
Per-user based packet filtering (by e.g. deep packet inspection) UE IP address allocation; UL and DL service level charging, gating and rate enforcement
DL rate enforcement based on AMBR;
E-UTRAN
(Evolved Node B)(scope 0f LTE)
Part of EPC
(Evolved Packet Core)(Scope of SAE)
MME / P-GW
-
5/26/2018 Anritsu Understanding LTE
14/6013 | Understanding LTE
Bearer service architecture
The end to end connectivity through the LTE/SAE network is made via the bearer service, which
describes the top level connectivity across the network. A radio bearer transports the packets of an EPS bearer between a UE and an eNB.
There is a one-to-one mapping between an EPS bearer and a radio bearer.
An S1 bearer transports the packets of an EPS bearer between eNodeB and ServingGW.
An S5/S8 bearer transports the packets of an EPS bearer between a Serving GW and aPDN GW.
A UE stores a mapping between an uplink packet filter and a radio bearer to create
the binding between an SDF and a radio bearer in the uplink.
A PDN GW stores a mapping between a downlink packet filter and an S5/S8a bearerto create the binding between an SDF and an S5/S8a bearer in the downlink.
An eNB stores a one-to-one mapping between a radio bearer and an S1 to create thebinding between a radio bearer and an S1 bearer in both the uplink and downlink.
A Serving GW stores a one-to-one mapping between an S1 bearer and an S5/S8abearer to create the binding between an S1 bearer and an S5/S8a bearer in both theuplink and downlink.
LTE technology
Target Performance objectives for LTE (Release 8).
When the project to define the evolution of 3G networks was started, the following targets were set by
Network Operators as the performance design objectives. It was against these objectives that the
different solutions were developed by various organisations and then proposed to 3GPP. The 3GPP
then had a study to consider the proposals, evaluate the performance of each, and then make a
recommendation for the way forward that would form the basis of LTE.
Peak data rate
Instantaneous downlink peak data rate of 100 Mb/s within a 20 MHz downlink spectrum
allocation (5 bps/Hz)
Instantaneous uplink peak data rate of 50 Mb/s (2.5 bps/Hz) within a 20 MHz uplink spectrum
allocation)
Control-plane latency
Transition time of less than 100 ms from a camped state, such as Release 6 Idle Mode, to an
active state such as Release 6 CELL_DCH
-
5/26/2018 Anritsu Understanding LTE
15/6014w w w . a n r i t s u . c o m
Transition time of less than 50 ms between a dormant state such as Release 6 CELL_PCH and
an active state such as Release 6 CELL_DCH
Control-plane capacity
At least 200 users per cell should be supported in the active state for spectrum allocations up
to 5 MHz
User-plane latency
Less than 5 ms in unload condition (ie single user with single data stream) for small IP packet
User throughput
Downlink: average user throughput per MHz, 3 to 4 times Release 6 HSDPA
Uplink: average user throughput per MHz, 2 to 3 times Release 6 Enhanced Uplink
Spectrum efficiency Downlink: In a loaded network, target for spectrum efficiency (bits/sec/Hz/site), 3 to 4 times
Release 6 HSDPA
Uplink: In a loaded network, target for spectrum efficiency (bits/sec/Hz/site), 2 to 3 times
Release 6 Enhanced Uplink
Mobility
E-UTRAN should be optimized for low mobile speed from 0 to 15 km/h
Higher mobile speed between 15 and 120 km/h should be supported with high performance
Mobility across the cellular network shall be maintained at speeds from 120 km/h to 350 km/h
(or even up to 500 km/h depending on the frequency band)
UE eNB S-GW P-GW Peer
Entity
End-to-End Service
EPS Bearer External Bearer
Radio Bearer S1 Bearer S5/S8 Bearer
Radio S1 S5/S8 Gi
E-UTRAN EPC INTERNET
-
5/26/2018 Anritsu Understanding LTE
16/6015 | Understanding LTE
Coverage
Throughput, spectrum efficiency and mobility targets above should be met for 5 km cells, and
with a slight degradation for 30 km cells. Cells range up to 100 km should not be precluded.
Further Enhanced Multimedia Broadcast Multicast Service (MBMS)
While reducing terminal complexity: same modulation, coding, multiple access approaches
and UE bandwidth than for unicast operation.Provision of simultaneous dedicated voice and
MBMS services to the user.
Available for paired and unpaired spectrum arrangements.
Spectrum flexibility
E-UTRA shall operate in spectrum allocations of different sizes, including 1.25 MHz, 1.6 MHz,
2.5 MHz, 5 MHz, 10 MHz, 15 MHz and 20 MHz in both the uplink and downlink. Operation inpaired and unpaired spectrum shall be supported.
The system shall be able to support content delivery over an aggregation of resources
including Radio Band Resources (as well as power, adaptive scheduling, etc) in the same and
different bands, in both uplink and downlink and in both adjacent and non-adjacent channel
arrangements. A Radio Band Resource is defined as all spectrum available to an operator.
Co-existence and Inter-working with 3GPP Radio Access Technology (RAT)
Co-existence in the same geographical area and co-location with GERAN/UTRAN on adjacent
channels.
E-UTRAN terminals supporting also UTRAN and/or GERAN operation should be able to
support measurement of, and handover from and to, both 3GPP UTRAN and 3GPP GERAN.
The interruption time during a handover of real-time services between E-UTRAN and UTRAN
(or GERAN) should be less than 300 msec.
Architecture and migration
Single E-UTRAN architecture
The E-UTRAN architecture shall be packet based, although provision should be made to
support systems supporting real-time and conversational class traffic
E-UTRAN architecture shall minimize the presence of "single points of failure"
E-UTRAN architecture shall support an end-to-end QoS
Backhaul communication protocols should be optimised
Radio Resource Management requirements
Enhanced support for end to end QoS
Efficient support for transmission of higher layers
Support of load sharing and policy management across different Radio Access Technologies
-
5/26/2018 Anritsu Understanding LTE
17/6016w w w . a n r i t s u . c o m
Complexity
Minimize the number of options
No redundant mandatory features
So we can see that LTE refers to a new radio access technology to deliver higher data rates (50-
100MB/s), and fast connection times. The technology solution chosen by 3GPP uses OFDMA access
technology, and MIMO technologies together with high rate (64QAM) modulation. LTE uses the same
principles as HSPA (in existing Release 6 3GPP networks) for scheduling of shared channel data, HARQ,
and fast link adaptation (AMC adaptive modulation and coding). This technology enables the network
to dynamically optimise for highest cell performance according to operator demands (e.g. speed,
capacity etc).After evaluation of the different industry proposals, a recommendation was made to adopt an OFDMA
based approach as part of a completely new air interface. The rationale for this was to chose revolution
rather than evolution because in the long term this new air interface would offer the required data rates
with the ability to implement in relatively low cost and power efficient hardware. It was felt that an
evolutionary approach based on further enhancement to WCDMA would be able to meet the
technical requirements, but the technology demands to implement this may be unsuitable for mobile
devices when considering power consumption, processing power etc. The OFDM based technology
offers a simpler implementation of the required high speed data rates.The performance of the selected technology has been modelled, and is predicted to meet the
original requirements laid out in the LTE requirements specification.
The key features of the LTE air interface are:
Downlink
OFDMA based access, with QPSK, 16QAM 64QAM modulation
Downlink multiplexing
MIMO and transmit diversity
MBMS
Scheduling, link adaptation, HARQ and measurements like in 3.5G
Uplink
Single Carrier FDMA access, with BPSK, QPSK, 8PSK and 16QAM modulation
Transmit diversity
Scheduling, link adaptation, HARQ and measurements like in 3.5G
Random Access Procedures
-
5/26/2018 Anritsu Understanding LTE
18/6017 | Understanding LTE
Multiple Input Multiple Output (MIMO)
Employs multiple antennas at both the base station transmitter and terminal receiver
If multiple antennas are available at the transmitter and receiver, the peak throughput can beincreased using a technique known as code re-use.
Each channelisation/scrambling code pair allocated for PDSCH transmission can
modulate up to M distinct data streams, where M is the number of transmit antennas.
In principle, the peak throughput with code re-use is M times the rate achievable with a single
transmit antenna.
Compared to the single antenna transmission scheme with a larger modulation constellation to
achieve the same rate, the code re-use technique may have a smaller required Eb/No,
resulting in overall improved system performance.
OFDMA is used to provide higher data rates than used in 3G through the use of a wider transmission
bandwidth. The 5 MHz channel is limiting for W-CDMA data rates, and use of a wider RF band (20 MHz)
leads to group delay problems that limit data rate. So, OFDM breaks down the 20 MHz band into many
narrow bands (sub-channels) that do not suffer from the same limitation. Each sub-channel is modulated
at an optimum data rate and then the bands are combined to give total data throughput. Algorithms
select the suitable sub-channels according to the RF environment, interference, loading, quality of each
channel etc. These are then re-allocated on a burst by burst level (each sub-frame, or 1 ms). The OFDMfrequencies in LTE have been defined with a carrier spacing of 15 kHz. Each resource block (that
represents an allocation of radio resource to be used for transmission) is a group of 12 adjacent sub-
carriers (therefore 180 kHz) and a slot length of 0.5 ms
MIMO is an abbreviation of Multiple Input Multiple Output. This is an antenna technology together
with signal processing that can increase capacity in a radio link. In LTE, the user data is separated into 2
data streams, and these are then fed to 2 separate TX antennas, and received by 2 separate RX
antenna. Thus the data is sent over 2 separate RF paths. The algorithm used to split and then recombine
the paths allows the system to make use of the independence of these 2 paths (not the same RF lossesand interference on both) to get extra data throughput better than just sending the same data on 2
paths. This is done by separating the data sets in both space and time. The received signals are then
processed to be able to remove the effects of signal interference on each, and thus creating 2 separate
signal paths that occupy the same RF bandwidth at the same time. This will then give a theoretical
doubling of achievable peak data rates and throughput in perfect conditions where each RF path is
completely isolated and separate from the other path.
-
5/26/2018 Anritsu Understanding LTE
19/6018w w w . a n r i t s u . c o m
For LTE-Advanced (Release10) the target has been stretched further, to provide 1GB/s peak data rate
capacity in a static environment, and 100MB/s in high mobility environment. The target has been met
using some additional technologies that enable 1GB/s downlink and 500MB/s uplink in staticconditions. LTE Advanced has been designed as an upgrade to existing LTE networks, and backwards
compatible with them also. The higher data rate capacity has been achieved then by using two key
technologies, Carrier Aggregation and higher layer MIMO processing. LTE Advanced uses the same
basic RF carriers as LTE, with same OFDMA access and channel specifications, but is now able to
combine multiples of these carriers for simultaneous transmission and hence provide higher bandwidths
and higher data rates. Each OFDMA carrier is now called a Component Carrier (CC) and they can then
be aggregated across a single band as adjacent carriers in a contiguous spectrum, or they can be
aggregated across different bands as a non-contiguous spectrum. This is designed to give a TelecomOperator the maximum flexibility in using the different portions of RF spectrum for which they are
holding a license (availability of RF spectrum being one of the key limitations now for deployment of
higher data rate mobile networks).
X X
X
X
XX
XX
+
+
-
5/26/2018 Anritsu Understanding LTE
20/6019 | Understanding LTE
The chart below shows how LTE Advanced can be deployed as a set of separate 20 MHz CCs (LTE
Release 8 compatible mode), or as two sets of 40 MHz dual/adjacent CCs each offering twice the
bandwidth of LTE, or even as a set of five CCs to give a five times bandwidth
increase.
LTE Advanced is also increasing the MIMO capabilities in the network. It will extend the downlink single
User MIMO from 4x4 architecture (maximum 4 x increase in data rate) to an 8x8 capability with up to
8x increase in data rate. This Single User MIMO can also now be selectively applied using a custom
algorithm per user (rather than the limited code book algorithms used in LTE) to further optimise the
data rates for a single user. For the first time, Single User MIMO is introduced on the uplink, providing
up to 4x4 MIMO capabilities to provide 4 x increases in data rates.
To support the more advanced MIMO features in LTE Advanced, there are two additional types of
reference signal introduced that enable more sophisticated MIMO that is more able to adapt to the
channel conditions. The Channel State Information Reference Signal (CSI-RS) is a specific downlink
Reference Signal that can be used by the UE for downlink channel sounding for more accurate
estimation of the downlink channel propagation (uplink channel sounding is available already in Release
8). Secondly, UE specific Demodulation Reference (DM-RS) signals are introduced. This enables MINO
Frequency
CC, e.g., 20 MHzSystem Bandwidth,e.g., 100 MHz
UE Capabilties
100 MHz case
40 MHz case
20 MHz case(Rel. 8LTE)
-
5/26/2018 Anritsu Understanding LTE
21/6020w w w . a n r i t s u . c o m
pre-coding using UE specific codes rather than the fixed set of the Release 8 code book, which in turn
enables more successful MIMO implementation and better throughput using the channel conditions.
To improve cell coverage and data rates, particularly at the cell edge or just beyond, there are two
further technologies being introduced in LTE Advanced, these are Co-ordinated Multi Point (CoMP)
and Relaying. These are both antenna/scheduling/architecture changes to increase coverage. CoMP is
used to enable transmission from two separate eNB to be co-ordinated together in their transmission
to a UE. This is then used in two different modes; Joint Processing (JP) where the transmission of user
data on the PDSCH is made jointly by two eNodeBs, or Coordinated Scheduling/Coordinated
Beamforming (CS/CB).
The Joint Processing (JP) mode can operate in two different ways:
PDSCH data is sent on simultaneous joint transmission (JT) from each eNodeB (but with aseparate Dynamic Mode Reference Signal DM-RS) that enables each transmission to be
received at the same time and the data streams combined.
PDSCH is dynamically selected between the two eNodeB to dynamically select the optimum
eNodeB to receive from given the propagation path.
Coordinated Scheduling uses the scheduler in each eNodeB to interact together to allow beamforming
and Resource Block scheduling for two UEs in the same area when they are supported by two
eNodeBs. This enables each UE to receive a good quality data stream without interference from the
adjacent UE being supported from another cell. This is a step ahead of the ICIC function in Release8that focuses on the interference aspects of scheduling between adjacent cells, but does not take into
account beamforming being used to improve data rates at the cell boundary.
CoMP is also possible in the Uplink, using shared scheduling between adjacent eNodeB so that the
uplink from the UE can be received on both eNodeBs and then the data streams combined at a central
eNodeB that is controlling the scheduling in each of the two active eNodeBs
Coherent combining ordynamic cell selection
Coordinated scheduling/beamformingJoint transmission/dynamic cell selection
-
5/26/2018 Anritsu Understanding LTE
22/6021 | Understanding LTE
In the LTE Advanced Relaying function, an eNodeB can relay data to a secondary eNodeB (called the
Relay Node RN) that is providing coverage to an area within the coverage of the base eNodeB. Using
this technology, the coverage can be extended close to the cell edge without the need for additional
backhaul links or infrastructure. The eNodeB will be able to relay a data stream across from its own
backhaul link across to the Relay Node and hence allow a UE to connect to the Relay Node. The Relay
Node will therefore be able to extend the coverage of the base eNodeB without the need for
additional backhaul infrastructure. The Relay Node will appear as a normal eNodeB to the UE and theRelay Node will provide all Scheduling and HARQ functions.
LTE Protocols and Signalling
When 3GPP started to develop the radio interface protocols of the Evolved UTRAN the following initial
assumptions were made: Simplification of the protocol architecture and the actual protocols
Higher node
UEeNB
RN
Cell ID #x
Cell ID #y
Multipoint reception
Receiver signal processing atcentral eNB (e.g., MRC, MMSEC)
-
5/26/2018 Anritsu Understanding LTE
23/6022w w w . a n r i t s u . c o m
No dedicated channels, and hence a simplified MAC layer (without MAC-d entity)
Avoiding similar functions between Radio and Core network.
LTE physical layer channel structure
The E-UTRAN has been designed as part of an all IP network, see the section on SAE for more details.
But, some basic consequences from this are that there are no longer any circuit switched elements in
the network, everything is now packet based. Further, the use of shared and broadcast channels that
are introduced in earlier versions of 3GPP (e.g. HSDPA, HSUPA, MBMS) are re-used in LTE. In fact, the
design is based fully on shared and broadcast channels, and there are no longer any dedicated channels
to carry data to specific users. This is to increase efficiency of the air interface, as the network can control
the use of the air interface resources according to the real time demand from each user, and no longerhas to allocate fixed levels of resource to each user independent of real time data requirements.
The protocol stack for LTE is based on a standard SS7 signalling model, as used with 3GPP W-CDMA
networks today. In this model, in layer 3 the Non Access Stratum (NAS) is connected to the logical
channels. These logical channels provide the services and functions required by the higher layers (NAS)
to deliver the applications and services. The logical channels are then mapped onto transport channels
in Layer 2, using the RRC elements. These provide control and management for the flow of the data,
such as re-transmission, error control, and prioritisation. User data is managed in Layer 2 by the Packet
Data Convergence Protocol (PDCP) entity. The air interface and physical layer connection is thencontrolled and managed by the Layer 1, using RLC and MAC entities and the PHY layer. Here the
transport channels are mapped into the physical channels that are transmitted over the air.
LTE radio channels are separated into 2 types, physical channels and physical signals. A physical channel
corresponds to a set of resource elements carrying information originating from higher layers (NAS) and
is the interface defined between 36.212 and 36.211. A physical signal corresponds to a set of resource
elements used only by the physical layer (PHY) but does not carry information originating from higher
layers.
Based on the above architecture, the downlink consists of 5 physical channels and 2 physical signals:
Downlink Physical Channels
1. Physical broadcast channel (PBCH)
The coded BCH transport block is mapped to four subframes within a 40 ms interval, 40
ms timing is blindly detected, i.e. there is no explicit signalling indicating 40 ms timing.
Each subframe is assumed to be self-decodable, i.e the BCH can be decoded from a
single reception, assuming sufficiently good channel conditions.
2. Physical control format indicator channel (PCFICH)Informs the UE about the number of OFDM symbols used for the PDCCHs;
-
5/26/2018 Anritsu Understanding LTE
24/6023 | Understanding LTE
Transmitted in every subframe.
3. Physical downlink control channel (PDCCH)
Informs the UE about the resource allocation, and hybrid-ARQ information related to
DL-SCH, and PCH. Carries the uplink scheduling grant.
4. Physical downlink shared channel (PDSCH)
Carries the DL-SCH. This contains the actual user data.
5. Physical multicast channel (PMCH)
Carries the MCH. This is used to broadcast services on MBMS.
Downlink Physical Signals
1. Reference signal
2. Synchronization signal
The corresponding uplink consists of 4 physical channels and 2 physical signals:
Uplink Physical Channels
1. Physical uplink control channel (PUCCH)
Carries ACK/NAKs in response to downlink transmission. Carries CQI reports.
2. Physical uplink shared channel (PUSCH)
Carries the UL-SCH. This contains the user data.3. Physical Hybrid ARQ Indicator Channel (PHICH)
Carriers ACK/NAKs in response to uplink transmissions.
4. Physical random access channel (PRACH)
Carries the random access preamble.
Uplink Physical Signals
1. Demodulation reference signal, associated with transmission of PUSCH or PUCCH.
2. Sounding reference signal, not associated with transmission of PUSCH or PUCCH.
So we can see that both the uplink and downlink are composed of a shared channel (to carry the data)
together with its associated control channel. In addition there is a downlink common control channel
that provides non user data services (broadcast of cell information, access control etc).
Within the LTE protocol stack, the physical layer channels (described above) are mapped through to the
higher layers via the functions of the MAC and RLC layers of the protocol stack. This is shown below for
both the user plane and control plane data. Here we can see the simplification of the network due to
the SAE architecture discussed previously. The eNB is responsible for managing the air interface and
flow control of the data, and the aGW is responsible for the higher layer control of user data within
PDCP and NAS services.
-
5/26/2018 Anritsu Understanding LTE
25/6024w w w . a n r i t s u . c o m
LTE transport channel structure
Having now defined the physical layer channels, and the requirements of the higher layers in the
protocol stack, we can now take a look at the transport channels types in EUTRAN, which are definedas follows:
Downlink Transport Channel types are:
Broadcast Channel (BCH) characterised by:
fixed, pre-defined transport format;
requirement to be broadcast in the entire coverage area of the cell.
Downlink Shared Channel (DL-SCH) characterised by:
support for HARQ;
support for dynamic link adaptation by varying the modulation, coding and transmit power;
possibility to be broadcast in the entire cell;
possibility to use beamforming;
support for both dynamic and semi-static resource allocation;
support for UE discontinuous reception (DRX) to enable UE power saving;
support for MBMS transmission (FFS).
NOTE: the possibility to use slow power control depends on the physical layer.
Paging Channel (PCH) characterised by:
support for UE discontinuous reception (DRX) to enable UE power saving (DRX cycle is
indicated by the network to the UE);
requirement to be broadcast in the entire coverage area of the cell;
mapped to physical resources which can be used dynamically also for traffic/other control
channels.
Multicast Channel (MCH) characterised by:
requirement to be broadcast in the entire coverage area of the cell;
support for SFN combining of MBMS transmission on multiple cells;support for semi-static resource allocation e.g. with a time frame of a long cyclic prefix.
Uplink Transport Channel types are:
Uplink Shared Channel (UL-SCH) characterised by:
possibility to use beamforming; (likely no impact on specifications)
support for dynamic link adaptation by varying the transmit power and potentially modulation
and coding;
support for HARQ;
support for both dynamic and semi-static resource allocation.NOTE: the possibility to use uplink synchronisation and timing advance depend on the
physical layer.
-
5/26/2018 Anritsu Understanding LTE
26/6025 | Understanding LTE
Random Access Channel(s) (RACH) characterised by:
limited control information; collision risk;
LTE Logical channel structure
To complete the channel mapping, the transport channels are mapped onto the logical channels in the
protocol stack. These logical channels then provide the functionality to the higher layers in the protocol
stack, and they are specified in terms of the higher layer services which they support. Each logical
channel type is defined by what type of information is transferred. In general, the logical channels are
split into two groups:
1. Control Channels (for the transfer of control plane information);
2. Traffic Channels (for the transfer of user plane information).Control channels are used for transfer of control plane information only. The control channels are:
Broadcast Control Channel (BCCH)
A downlink channel for broadcasting system control information.
Paging Control Channel (PCCH)
A downlink channel that transfers paging information. This channel is used when the network
does not know the location cell of the UE.
Common Control Channel (CCCH) Multicast Control Channel (MCCH)
A point-to-multipoint downlink channel used for transmitting MBMS control information from
the network to the UE, for one or several MTCHs. This channel is only used by UEs that
receive MBMS.
Dedicated Control Channel (DCCH)
A point-to-point bi-directional channel that transmits dedicated control information between a
UE and the network. Used by UEs when they have an RRC connection.
Traffic channels are used for the transfer of user plane information only. The traffic channels are:
Dedicated Traffic Channel (DTCH)
A Dedicated Traffic Channel (DTCH) is a point-to-point channel, dedicated to one UE, for the
transfer of user information. A DTCH can exist in both uplink and downlink.
Multicast Traffic Channel (MTCH)
A point-to-multipoint downlink channel for transmitting traffic data from the network to the
UE. This channel is only used by UEs that receive MBMS.
The mapping from logical channels to transport channels to physical channels is shown below:
-
5/26/2018 Anritsu Understanding LTE
27/6026w w w . a n r i t s u . c o m
LTE Channel Mapping
Where LTE Advanced is being used, then the DL-SCH is mapped into multiple Transport Channels that
match the separate CCs being used for each OFDMA carrier. This ensures that the same channel
coding and format can be used between LTE Release 8 (single CC) and LTE Advanced Release 10
(multiple CCs). This avoids needing to re-develop the channel structure and MAC layers between
Release 8 and Release 10, and provides the forwards/backwards compatibility between the twoversions.
PCCH BCCH CCCH DCCH DTCH MCCH MTCH
PCH BCH DL-SCH MCH
PDCCH PBCH PDSCH PCFICH PHICH PMCH
DCI
CFI
HI
Downlink
Logical
Channels
Downlink
Transport
Channels
Downlink
Physical
Channels
CCCH DCCH DTCH
RACH UL-SCH
PRACH PUSCH PUCCH
UCI
Uplink
Logical
Channels
Uplink
Transport
Channels
Uplink
Physical
Channels
ChannelCoding
HARQ
Mod.
Mapping
ChannelCoding
HARQ
Mod.
Mapping
ChannelCoding
HARQ
Mod.
Mapping
ChannelCoding
HARQ
Mod.
Mapping
TransportBlock
TransportBlock
TransportBlock
TransportBlock
CC
Downlink: OFDMA with componentcarrier (CC) based structure
- Priority given to reusing Rel.8specification for low cost andfast development
One transport block (TB),
which corresponds to a channel coding block and a retransmission unit, is mapped within one CC
Parallel-type transmission for multi-CC transmission
Good affinity to Rel.8 LTE specifications
-
5/26/2018 Anritsu Understanding LTE
28/6027 | Understanding LTE
MAC Scheduler
All user data transmissions in LTE are made by pre-scheduled transmissions of specific packets of data,
there are no continuous circuit connections as with previous cellular technologies, this is reflecting themobile broadband and all IP nature of LTE. All of the scheduling for transmissions, both downlink and
uplink, are made by the MAC scheduler in the eNodeB. This entity will decide the instantaneous data
rate and capacity given to each user in the network. Resources are scheduled based on reported CQI
and other factors. The algorithm for this is not specified by 3GPP, and so different eNodeB
manufacturers and network operators can develop and tune the algorithms to give different
performance or behaviours in their network.
The scheduling assignments are sent on the DCI/DPCCH channels, and are DL-SCH/PDSCH
scheduling assignments for the UE to receive data, and UL-SCH/PUSCH scheduling assignments (ULgrants) for the UE to transmit data. The UE can not set the uplink scheduling, as this must be co-
ordinated across all UEs in the cell, and so this is done in the eNodeB. The UE can request UL-SCH
resources by one of two methods, and then wait for the eNodeB to respond with a scheduling
assignment:
Explicitly by sending an SR (Scheduling Request) on UCI/PUCCH
Implicitly by sending a BSR (Buffer Status Report) on UL-SCH/PUSCH
The MAC has 2 scheduling modes:
Dynamic (based on dynamic requests and assignments)
Semi-persistent (based on static assignments, for e.g. voice traffic)
The semi-persistent scheduling is used for applications where the network expects to have a continuous
need to the same scheduling on a repetitive basis. An example is for voice calls, where the voice is
coded and put into packets by the CODEC at a fixed rate, and then the packets need to be transmitted
at a fixed rate/interval during the entire voice call. With this mode, the network can have a persistent
schedule for the UE to receive each voice packet without the need to signal the UE in advance for each
packet. This reduces the amount of control signalling required and hence makes more radio resourceavailable for user data.
Inside the scheduler, the DRX sequence (Discontinuous Rx) has to be taken into account. This is the
process where the UE can switch off its receiver for fixed time periods (to save power and increase
stand-by time). The scheduler needs to know if the UE is likely to be asleep in DRX mode, and if so
then it needs to signal the UE to wake up before sending it resource allocations.
The process for dynamic scheduling is shown below:
-
5/26/2018 Anritsu Understanding LTE
29/6028w w w . a n r i t s u . c o m
MAC Dynamic Scheduling
Latency improvements within LTE
As part of the LTE protocol description, the RRC States were restricted to RRC Idle and RRC
Connected States. They are depicted below, in conjunction with the possible legacy UTRAN RRC. The
purpose of this is to simplify the protocol structure and number of possible states, and hence state
transitions. This will enable faster response times in the network to reduce latency for the user. In an
existing 3GPP W-CDMA network there are more possible states and state transitions, and in additionit takes some considerable time to move from one state to another. This leads to excessive delays when
trying to set up data links or re-configure the radio resources to be more efficient, to change the local
loading in the cell, or change to the demand or a particular user. For LTE Advanced, a further feature
that is introduced is to provide parallel Control Plane and User Plane signalling. This will improve latency
as the control plane will be more efficiently used, with both more control plane capacity and faster
responses available.
UE eNB
Dynamic
UL Scheduling
SR (UCI/PUCCH)
UL Grant (DCI/PDCCH)
UL Data + BSR (UL-SCH)/PUSCH)
UL Grant (DCI/PDCCH)
UL Data + BSR (UL-SCH/PUSCH)
UL Data
UE eNB
Dynamic
DL Scheduling
DL assignment (DCI/PDCCH)
DL Data (DL-SCH/PDSCH)
DL Assignment (DCI/PDCCH)
DL Data (DL-SCH/PDSCH)
DL Data
-
5/26/2018 Anritsu Understanding LTE
30/6029 | Understanding LTE
RRC States and interRAT mobility procedures
In addition, the Transmission Time Interval (TTI) of 1ms was agreed (to reduce signalling overhead and
improve efficiency). The TTI is the minimum period of time in which a transmission or re-transmission
can take place. Having a short TTI means that when messages are received, a reply can be scheduled
much faster (the next available transmission slot will be sooner), or a re-transmission of a failed message
can take place much sooner.
LTE typical implementations
A Typical implementation of the downlink is shown below, giving the various coding and processing
stages to go from the logical channel (user/data stream) through to an air interface transmission and
back through the receiver to recover the logical channel. The example shows a typical downlink with
2 channels of MIMO.
CELL_DCH
Handover
Reselection
Reselection
CELL_FACH
CELL_PCH
URA_PCH
UTRA_IdleE-UTRA
RRC IDLE
E_UTRA
RRC_CONNECTED
GSM_Connected
GPRS Packet
transfer mode
GSM_Idle/GPRS
Packet_Idle
Handover
Reselection
Connection
establishment/release
CCO with
NACC
Connection
Establishment/release
CCO, Reselection
CCO,
Reselection
Connection
establishment/release
-
5/26/2018 Anritsu Understanding LTE
31/6030w w w . a n r i t s u . c o m
System Architecture Functional Diagram. Downlink Transmission and Reception.
Antenna Mapping
Resource Mapping
Data Modulation
Interleaving
Coding + RM
CRC
TX amp
& filters
TX amp
& filters
IFFT OFDM
signal generation
IFFT OFDM
signal generation
Antenna Mapping
Data Modulation
Interleaving
Coding + RM
CRC
MAC
Scheduler
Antenna
Mapping
Modulation
Scheme
Channel-state
information,etc. HARQ
Redundancy
Version
Resource/Power
Assignment
Redundancy for
error detection
N Transport Blocks
(Dynamic size S1..., Sn)
Redundancy for
data detection
QSPK, 16QAM,
64QAM
Multi-antenna
processing
NODE B
Resource Mapping
IQ modulator
& RF upconvert
Antenna Mapping
Resource Mapping
Data Modulation
Interleaving
Coding + RM
RX amp
& filters
RX amp
& filters
OFDM FTT
signal recovery
OFDM FFT
signal recovery
CRC
UE
IQ demodulator
& RF downconvert
IQ demodulator
& RF downconvert
Error
Indications
IQ modulator
& RF upconvert
ACK/NACK
HARQ info
Antenna Demapping
Resource Demapping
Data Demodulation
De-interleaving
Decoding + RM
ACK/NACK
HARQ info HARQ
-
5/26/2018 Anritsu Understanding LTE
32/6031 | Understanding LTE
Self-Optimising Networks (SON)
Another new concept being introduced for SAE networks is the Self-Optimising Network (or Self
Organising Network). The purpose of this is to reduce the complexity of deploying new nodes into thenetwork. This can be for new micro/macro cells in busy areas, for pico cells being installed into local
hotspots such as shopping centres or airports, or even femto cells being installed for coverage within
a single home.
Traditionally, when a new node is configured into the network there are a number of planning and
measurements that must be made by experts in the field, and then parameter setting and network
tuning will take place using other experts who are managing the network. This is all to do with setting
network power levels, neighbour cell lists for handover measurements, and configuring the node
correctly into all other network databases.The concept for SON is to allow this to take place automatically using software in the eNodeB, so all
necessary measurements are made automatically and reported to the network. In addition, the network
should be able to automatically transfer this information across to other network elements that will use
the information for configuration/optimisation purposes. This concept includes several different
functions from eNB activation to radio parameter tuning. The chart below shows a basic framework for
all self-configuration /self-optimization functions.
a-1: Configuration of IP address
and detection of OAM
a-2: Authentication of eNB/NW
a-3: Association to aGW
a-4: Downloading of eNB software (and operational parameters)
b-1: Neighbour list configuration
b-2: Coverage/capacity related
parameters configuration
c-1: Neighbour list optimisation
c-2: Coverage and capacity control
(A) Basic Setup
(B) Initial Radio
Configuration
(C) Optimization/
Adaptation
Self-Optimisation
(operational state)
Self-Configuration
(pre-operational state)
eNB power on
(or cable connected)
-
5/26/2018 Anritsu Understanding LTE
33/6032w w w . a n r i t s u . c o m
Self-configuration process is defined as the process where newly deployed nodes are configured by
automatic installation procedures to get the necessary basic configuration for system operation.
This process works in pre-operational state. Pre-operational state is the state from when the eNB is
powered up and has backbone connectivity until the RF transmitter is switched on.
The typical functions handled in the pre-operational state covered by the Self Configuration process
are:
Basic Setup
Initial Radio Configuration
Procedures to obtain the necessary interface configuration;
Automatic registration of nodes in the system provided by the network;
Self-optimization process is defined as the process where UE & eNB measurements and performance
measurements are used to auto-tune the network. This process works in operational state where the
RF interface is additionally switched on.
The typical functions handled in the operational state covered by the Self Optimization process are:
Optimization / Adaptation of network settings.
The distribution of data and measurements over interfaces;
Communication with functions/entities/nodes in charge of data aggregation for optimization
purpose;
Managing links with O&M functions and O&M interfaces relevant to the self optimization
process.
To enable SON it is also necessary that the UE shall support measurements and procedures which can
be used for self-configuration and self-optimisation of the E-UTRAN system.
To reduce the impact of SON on the UE (cost, complexity, battery life etc) measurements and reports
used for the normal system operation should be used as input for the self-optimisation process as far
as possible. For SON specific measurements required by the network, the network is able to configurethe measurements and the reporting for self-optimisation support by RRC signalling messages sent to
the UE.
-
5/26/2018 Anritsu Understanding LTE
34/6033 | Understanding LTE
Impact on users of the technology
Consumers
The key impact of LTE/SAE and the FMC vision for users of mobile communications will be the feeling
of always connected with the ability to have what I want, when I want, and where I want without
having to care about how to access the services. The range of services offered to a consumer should
become independent of the access technology, so that music download, instant messaging, voice and
video calling all become available in the same format wherever you are.
The FMC will enable users to have a single contact number (IP address) that can be taken anywhere in
the network, and the user can set profiles according to where they are and what they are doing. So a
mobile phone should automatically be able to connect to a home network, an office network, a public
network or a local hotspot without the user making any changes. The phone will then be able to
configure itself into office mode to provide office based services when in the office, and then change
to home services when the user returns home.
By integrating the mobile network to the fixed network through the IMS sub-system, the look and feel
of the network and services should be the same regardless of if it is a fixed or mobile network, or what
type of mobile network is connected to. LTE and SAE will allow the mobile network to provide high
data rates and low latency to a mobile user at a comparable rate to fixed line users. This will be vital in
ensuring the same feel to the services when in the mobile environment.Network Operators
There is a trend within network operators and service providers to offer Triple play and more services,
where multiple communications services are provided to a customer from a single subscription. This
strategy is to increase Average Revenue Per User (ARPU) and reducing churn by keeping multiple
services bundled into a single package. The move to NGN and FMC provides two key advantages to
provide this package. Firstly, the integration of the mobility management and data routing means that
it is more reliable and convenient to provide this to a customer, as they can achieve this with a single
telephone number and single device. Todays triple play solutions still require multiple access devices to
provide voice communications across different access technologies. Secondly, there is a lower OPEX
(OPerational EXpenditure) as the network is simplified, and this reduced the costs for the operator to
provide the services. The operator does not need multiple networks and technologies to be maintained
side by side for parallel services. As an example, todays triple play operators typically need to operate
and maintain the following types of network:
IP network for residential/business broadband, using a mix of fibre and copper. With
extensions for WLAN and WiMAX hubs.
Circuit Switched network for residential/business voice, using a mix of fibre and copper.
-
5/26/2018 Anritsu Understanding LTE
35/6034w w w . a n r i t s u . c o m
ATM network for mobile network infrastructure, using fibres.
DVB network for broadcast services (TV, radio etc)
This means that they may have separate infra-structure for each that has a set of associated running
costs, maintenance costs etc. When combining all of the services to fewer network elements and
common network IP technologies, then the network becomes more scaleable, and new services are
quickly rolled out or coverage increased without major new capital investments required.
By implementing an LTE/SAE network, the operators will be able to simplify the overall network
architecture and remove old legacy telecoms equipment that no longer provides competitive and cost
efficient use of the radio spectrum resources. At the same time, fixed line services will be made available
to mobile users without reduction in performance and feel of the service.
-
5/26/2018 Anritsu Understanding LTE
36/6035 | Understanding LTE
Testing challenges
RF Testing
The RF test requirements are given in 3GPP standards TS36.141 Base Station Conformance Test, and
TS36.521 UE Conformance Specification Radio transmission and reception. Examples of the common
radio transmit characteristics are shown below:
OFDM Radio testing
OFDM and the use of high order 64QAM modulation require high linearity, phase and amplitude in
both TX and RX modules to prevent inter-symbol interference and to enable accurate IQ demodulation.
This requires a fast and adaptive EVM measurement capability to track and measure the signals during
adaptive frequency channel use. Testing is made on both the per subcarrier performance of eachindividual sub-carrier, and then on the composite signal where the sub-carriers are combined and the
overall performance is seen.
The sub-carriers require good phase noise performance to prevent leakage across carriers. The
frequency mapping and orthogonal properties of OFDM require the null in one carrier phase response
being exactly on the peak on the adjacent carrier. Thus, accurate measurement of the phase linearity
and amplitude linearity on each sub-carrier is important for the orthogonal design (resistance to
interference) of the system.
The OFDM transmissions must also be measured per resource block to see how the power levels in
each burst are being correctly maintained. Each individual resource element (that is a single OFDM
carrier at one time duration/symbol) has a specific power level to be transmitted, and these power levels
should be correctly measured across a whole resource block.
Channel Power Occupied Bandwidth ACLR
Spurious Emmisions Spectral Emission Mask
-
5/26/2018 Anritsu Understanding LTE
37/6036w w w . a n r i t s u . c o m
The EVM measurement for LTE needs careful consideration because of 2 special features used. Firstly
there is the Cyclic Prefix (CP) which is a short burst of transmission at the start of each symbol. This is
actually a repeat of the end of the symbol, and is used to give a settling time to allow for delay spread
in the transmission path. If measurement is started too soon in the CP period then there will also be
signal from the previous symbol (inter-symbol interference, ISI) included that will corrupt the
measurement. The second point is that the symbol transmission has a ramp at the start and end toensure that there is no strong burst of power (a strong burst will create high levels of harmonic
distortion and interference). So the start and end of the symbol have an up/down ramp on the power.
Therefore we must also restrict the period of the symbol that is measured, to ensure we do not measure
in these ramp periods. The technique to address both these issues is to use a sliding FFT, where the
period of the symbol that is measured can be adjusted in time (sliding) to give the best EVM value. This
is shown in the diagram below.
-
5/26/2018 Anritsu Understanding LTE
38/6037 | Understanding LTE
The effect of the ramp can be seen in the measurements below. The waveform on the left has no ramp,
and so there is a sharp switch on/off between each symbol. This causes a large spectrum due to
switching emission that is seen as broadening of the output spectrum beyond the desired system
bandwidth (in this case 5 MHz). The waveform on the right has ramping enabled, and so there is a much
less severe switch on/off between symbols. This has the clear effect of reducing spectrum emissions.
This type of ramping (also called spectrum shaping) is required to ensure that the transmitter outputstays within the allocated frequency band and does not interfere with any adjacent frequencies.
Direct signal
Multi-path signal
CP
CP
Useful Symbol
Useful Symbol
EVM window (Analysis range)
EVM window (Analysis range)
EVM window (Analysis range)
Measurement result: Bad
(Include other symbols of multi-path)
Measurement result: Not Good
(Include ramp part)
Measurement result: Good
(Exclude other symbols and ramp)
RAMP RAMP
Change
FFT Timing
-
5/26/2018 Anritsu Understanding LTE
39/6038w w w . a n r i t s u . c o m
MIMO testing
In a MIMO system, the coupling from antenna to air characteristics must be fully understood. Data rate
and performance of MIMO links depend on how the multiple RF antennas couple to each other.Accurate calibration of antenna paths, factory calibration and then field installation calibration is required
to implement a successful MIMO system. During R&D phase, evaluation of designs is required to
confirm the sensitivity calculations required to find critical performance limiting issues.
The base station transmit antenna array may use specialist phased array techniques (like a Butler Matrix)
for accurate control of the phase/timing in each antenna path. This requires accurate characterisation
of the RF path in terms of electrical path length, coupling and reflections from both ends. This data is
then fed into the MIMO adaptation algorithms to enable features such as beam steering. A Vector
Network Analyser would normally be used for complete characterisation of the antenna paths.In testing of MIMO we should consider to test both the baseband processing section and the RF
generation/alignment. Both areas need to be tested for both functional test (correct operation) and
performance test (optimisation of algorithms for best processing and data throughput efficiency). In
addition, it is useful to check the negative test, which is to use deliberately incorrect signals and ensure
that they are correctly handled or rejected.
A good approach to developing a MIMO test strategy is to lay out a matrix of each of the areas and
stages for MIMO test, and then identify the required solutions for each part of the matrix. The key
Layer
Mapping
MIMO
pre-coding
Tx1
Tx2
Rx1
Rx2
Layer
Mapping
MIMO
equaliser
h11
h12
h21
h22
Tx
Baseband
Tx
Radio
Rx
Radio
Rx
Baseband
Tx
Module
Rx
Module
Test strategy partition of MIMO
-
5/26/2018 Anritsu Understanding LTE
40/60
elements of the matrix are to test the individual sub-units (tx baseband, tx radio, rx radio, rx baseband)
separately, and then as integrated tx and rx modules. So we can develop a test matrix as below:
In a MIMO system, it is necessary to calculate the characteristics of the RF path from each TX antennato each RX antenna. This is required so that the two paths can be separated by the processor and
effectively become two separate data paths. To achieve this, the system must accurately measure in real
time the RF path characteristics. These algorithms are built into the design of the particular MIMO
system used, but they all basically require the accurate phase and amplitude measurement of a pre-
amble or pilot tone that is a known signal. For testing environments this provides two challenges:
1. To ensure that the test system can generate accurate reference signals against which the
measurements are made. The accuracy of the received signals must be carefully measured, and the
test system calibrated to separate the measurement system uncertainty from the MIMO system
accuracy and uncertainty. This way, the exact characteristics of the MIMO system are measured, with
minimum influence from the test system. This requires the development of a test
method/environment to generate the reference signals against which the measurements are made,
and then to confirm the measurement method by adjusting the quality of the reference and
checking that the measured result matches to the change made.
2. The actual RF coupling from transmitter to receiver will affect the measured end to end system
performance. So for test environments used in performance measurement, algorithm tuning,
Integration and Verification (I&V), and production quality, the RF coupling between antenna must be
defined, repeatable and characterised if absolute performance figures (e.g. Mbit/second data rates)
are to be measured. This requires the use of suitable fading and multipath test equipment and
generation/profiles to create the different coupling between antennas. This can be achieved using
static signals (e.g. signal generator based references) for initial checking, and then through baseband
fading simulators to verify correct operation at algorithm level, and the finally RF fading simulators
for end to end system level testing.
Functional test
Performance test
Negative test
Tx
baseband
Tx
radio
Tx
module
Rx
radio
Rx
baseband
Rx
module
| Understanding LTE39
-
5/26/2018 Anritsu Understanding LTE
41/60
The MIMO coding of data blocks (block coding) is based on Space-Time Block coding, where the actual
coding of the data is based on both the space (i.e. which antenna) and time (when it is transmitted), and
the diversity gains of MIMO are from using diversity of both space and time for each block of data that
is sent. So we must measure both the time alignment of each antenna,