Fabric Requirements1/3 yard each: Tonga-B6387 Nectar Tonga-B6644 Berry Tonga-B6356 Spice Tonga-B6045 Amethyst Tonga-B6640 Sunset1/4 yard each: Tonga-B6042 Lotus Tonga-B6647 Carnival Tonga-B5407 Punch Tonga-B6646 Papaya3/8 yard Tonga-B4880 Purple5/8 yard each: Tonga-B9777 Storm Tonga-B6557 Garnet Tonga-B6642 Sun13/8 yards Tonga-B6645 Flamingo (includes 2/3 yard for binding)12/3 yards Tonga-B6638 Horizon21/2 yards Tonga-B6203 Aqua7 yards backing fabric of your choice84"x 99" batting
Cutting
From each Tonga-B6387 Nectar, Tonga-B6045 Amethyst and Tonga-B6640 Sunset:
• Cut one 87/8" x WOF strip. Sub-cut three 87/8" squares; cut once diagonally.
From Tonga-B6644 Berry:• Cut one 87/8" x WOF strip. Sub-cut four
87/8" squares; cut once diagonally.
From Tonga-B6356 Spice:• Cut one 87/8" x WOF strip. Sub-cut two
87/8" squares; cut once diagonally.
From Tonga-B6042 Lotus:• Cut one 55/8" x WOF strip. Sub-cut four
55/8" squares; cut once diagonally.
From Tonga-B6647 Carnival:• Cut one 55/8" x WOF strip. Sub-cut two
55/8"” squares; cut once diagonally.
From Tonga-B5407 Punch:• Cut one 55/8" x WOF strip. Sub-cut three
55/8" squares; cut once diagonally.
From Tonga-B6646 Papaya:• Cut one 55/8" x WOF strip. Sub-cut five
55/8" squares; cut once diagonally.
From Tonga-B4880 Purple:• Cut two 55/8" x WOF strips. Sub-cut nine
55/8" squares; cut once diagonally.
From Tonga-B9777 Storm:• Cut two 87/8" x WOF strips. Sub-cut eight
87/8" squares; cut once diagonally.
From both Tonga-B6557 Garnet and Tonga-B6642 Sun:• Cut nine 21/8" x WOF strips.
Sub-cut (160) 21/8" squares.
From Tonga-B6645 Flamingo:• Cut three 55/8" x WOF strips. Sub-cut sixteen
55/8" squares; cut once diagonally. • Cut eight 1" x WOF strips for border 1.• Cut nine 21/2" x WOF strips for binding.
From Tonga-B6638 Horizon:• Cut one 55/8" x WOF strip. Sub-cut three
55/8" squares; cut once diagonally. • Cut one 87/8" x WOF strip. Sub-cut three
87/8" squares; cut once diagonally. • Cut eight 51/2" x WOF strips for border 2.
From Tonga-B6203 Aqua:• Cut twenty 21/2" x WOF strips. Sub-cut (320) 21/2"
squares; cut once diagonally (A).• Cut four 87/8" x WOF strips. Sub-cut sixteen
87/8" squares; cut once diagonally.
2
Block ConstructionAll seam allowances are 1/4" and pieces are sewn right sides together. Note that triangles cut from 55/8" squares are referred to as small and those cut from 87/8" squares are referred to as large.
1. Noting the orientation, sew a B6203 Aqua triangle A to opposite sides of the 21/8" B6642 Sun squares (figure 1). Press the seams toward the square. Make a total of 160 units.
2. Repeat step 1 with eighty 21/8" B6557 Garnet squares (figure 2).
3. Sew the remaining B6203 Aqua triangles A to two adjacent sides of the remaining eighty 21/8" B6557 Garnet squares (figure 3).
4. Sew together the step 1-3 units as shown to make eighty pieced strips (figure 4).
5. Noting the orientation and following the fabric combinations listed in the chart below, sew a large triangle to the top and a small triangle to the bottom of each step 4 strip. Press the seams toward the triangles. Trim all blocks to 81/2" square.
3
Timeless Treasures483-485 Broadway, New York, NY 10013 • Phone 212-226-1400 • Fax 212-925-4180 www.ttfabrics.com
Block ChartFabrics for large/small triangles are listed
below Block Name.
Denise Russellwww.piecedbrain.com
©2018 Timeless Treasures www.ttfabrics.comThis pattern is for individual home use only. This pattern may not be reproduced for commercial purposes (i.e., may not be sold).
Quilt Top Assembly6. Following the quilt photo and quilt assembly
diagram for block placement and orientation, lay out ten rows of eight blocks each. Sew the blocks together in each row, then sew the rows together in order, matching adjacent seams.
7. For border 1, sew eight 1" B6645 Flamingo border strips together end to end using diagonal seams. Measure the length of the quilt top through the center and cut two border 1 strips that length. Sew one strip to each side of the quilt top. Measure the width of the quilt top through the center. Cut two border 1 strips that length and sew one to the top and one to the bottom. Press the seams toward the borders.
8. Repeat step 7 with the eight 51/2" B6638 Horizon strips to make and add border 2.
4
Finishing9. Layer the quilt top, batting and backing, and quilt
as desired.
10. Stitch the binding strips together end to end using diagonal seams. Fold and press the resulting long strip in half lengthwise with wrong sides together. Stitch to the quilt front, matching raw edges and mitering the corners.
11. Fold the binding to the quilt underside and hand-stitch the folded edge to the quilt back.