Download - Barrel Mod
-
8/2/2019 Barrel Mod
1/16
The AGM MP40 Barrel / Hop fix.
This is a guide based on the Taffy mod that first appeared on ASCUK, I have
added a few more pics & refined a few parts to make it more easy to understand.
Please note this involves a destructive method which could possibly leave you witha broken hope unit, this modification is done at your own risk & I will not be held
responsible for any damage or adverse affects on your gun.
The benefits for a successful modification will be a more accurate gun with greater
range & should also prove a power increase, the standard AGM barrel is a very
poor quality & way over size in internal bore & the hop unit as standard can not
be opened up as it is glued & non serviceable as standard.
The parts needed are a replacement inner barrel of 229mm in length from either a
TM mp5 or similar & a replacement clear silicone hop rubber, this is important
for easy line up on the barrel, I opted for a 6.04mm TM compatible Systemabarrel,
Parts list,
1x 229mm Systema 6.04mm barrel, aprox 17.50
1x Guarder clear silicone hop rubber, aprox 6
parts sourced from ehobby asia & price includes postage.
Tool List,
Small & medium Phillips screwdrivers
Coarse abrasive paper
De greaser
Thread lock
Superglue
12mm insulating tape
Craft Knife
Junior Hacksaw
Dremil type tool or small file
When using hand tools such as craft knifes & power tools always wear gloves &
eye protection.
Step 1.
Remove The two halves of the gun, take the upper receiver / barrel part & remove
the 4 screws that hold the barrel unit to the receiver, ( two are in the magazine
well)
-
8/2/2019 Barrel Mod
2/16
when the screws are removed pull the magazine well plastic liner out:
-
8/2/2019 Barrel Mod
3/16
then separate the barrel from the receiver, undo the two small screws that hold the
hop unit to the outer barrel unit & withdraw the hop unit & inner barrel from the
outer barrel:
now the hop unit & inner barrel have been withdrawn undo the two small screws
that hold the hop adjustment slider on & put them safe, now an extra small Philips
screw can be seen which hold the hop lever into the hop unit, this can be left in,
now take your junior hacksaw & cut around the moulding line in the hop unit, cut
right through to the barrel, see pic, cut where red line is:
-
8/2/2019 Barrel Mod
4/16
once cut it should look like this:
-
8/2/2019 Barrel Mod
5/16
you should now be able to slide the cut part down the barrel, we will call this part
barrel spacer 2, on the barrel before you cut the hop unit you will have noticed a
circular black ring, we will call this part barrel spacer 1, holding the hop unit in
one hand & the barrel in the other pull apart, it may take some strength as glue
from the factory may have it partially stuck, when the barrel comes free you will
have part of the inner hop unit on the barrel,
Remove the small plastic clip that holds the barrel, the inner hop unit should now
come off, discard the hop rubber & the hop bucking, clean any swarf out of the
hop unit, discard the barrel retaining clip, now cut the inner hop unit as shown in
picture, the part on the left we will keep & call it barrel collar discard the other
part,
-
8/2/2019 Barrel Mod
6/16
Now comes the re assembly process, take the 3 previously recovered parts barrel
spacer 1, barrel spacer 2 & barrel collar & either using a file or dremil type crafttool abraid the inner surfaces till they are big enough to fit over the new barrel,
the new barrel is larger in diameter than the standard item, it important they need
to be a good snug fit & not to loose, de grease all 3 parts, now abraid the new
barrel & de grease, its essential to have no grease on this so the glue sticks, now
look at the new barrel, you will notice a small line machined in it on the opposite
side to the hop hole, slide the part barrel collar onto the barrel, this should be a
good snug fit & not loose, line the small grove in the plastic with the grove in the
barrel, & put it into the outer hop unit, the grove in the plastic barrel collar
lines up with a grove in the hop unit, ensuring the alignment of the hop hole in the
barrel,
-
8/2/2019 Barrel Mod
7/16
now comes the hard bit, without twisting the barrel push the barrel collar into the
hop unit so its flush the hop unit,
-
8/2/2019 Barrel Mod
8/16
Keeping the hop unit & barrel collar in the position above move the barrel so it
aligns the hole in the barrel right in the centre of the hole in the hop unit, you may
need to pinch the hop unit with pliers so the barrel collar stays flush with the hop
unit as you move the barrel in & out, its important not to turn the barrel, when
the hole is lined up right put 1 drop of superglue between the barrel & the barrel
collar making sure it does not go on the hop unit,
After applying the glue & leaving it to set withdraw the barrel & barrel collar,
check the line on the outer of the barrel collar is lined up with the line cut in the
barrel, if its not pull the collar off & start again, if its ok put superglue right
around the the barrel letting it run in between the barrel & barrel collar, do this
with the barrel out of the hop unit, see pic:
-
8/2/2019 Barrel Mod
9/16
Once the glue has dried push the barrel & collar back into the hop unit so the hole
is aligned in the hop unit & the collar is flush with the front end of the hop unit:
-
8/2/2019 Barrel Mod
10/16
Now slide the part barrel spacer 2 that we cut of before down the barrel & glue
in place so its butted up against the barrel collar & hop unit, then slide the part
we called barrel spacer 1 down the barrel & glue it in position so its right up
against barrel spacer 2 when the glue is dry withdraw the barrel from the hop
unit, the barrel will now have the 3 parts attached & it should look like this:
now you notice the hop rubber is too long! Not to worry, trim about 7mm off the
end with a knife:
-
8/2/2019 Barrel Mod
11/16
now slip over the hop rubber onto the barrel & tape on with good quality 12mm
insulation tape, this needs to be good tape as there are crap brands out there, it
should look like this:
-
8/2/2019 Barrel Mod
12/16
now insert into hop unit, if you have done everything else correct it should now be
perfectly aligned,
now fit the hop bucking / spacer part:
-
8/2/2019 Barrel Mod
13/16
then re attach the hop adjustment slider, you can now see the perfect profile of the
hop rubber when you add hop, note on these hop rubbers even with the hop right
off you may see a slight protrusion of the rubber through the hole, this does not
affect the use of the gun, a smaller diameter hop bucking could be fitted to remedythis but I have found it not to be a problem, I have successfully done 5 of these
conversions so far,
-
8/2/2019 Barrel Mod
14/16
Now to stop the barrel rattling around at the front of the barrel wrap insulation
tape around it, then insert the inner barrel & hop unit into the outer barrel, it
should fit ok & the barrel spacers should butt fit right up against the outer barrel
making it a tight fit stopping the barrel moving forwards, on one I did there was avery slight bit of play, I fixed this with a little instant gasket applied like in pic:
-
8/2/2019 Barrel Mod
15/16
fitted:
job done, now fit the barrel into the upper receiver, fit the plastic magazine liner
-
8/2/2019 Barrel Mod
16/16
& the 4 screws, the shorter 2 go into the magazine well & the longer 2 go through
the outer receiver, ( on early ones all 4 screws may be the same length) I put
thread lock on these screws as I have had them come loose!
Put the 2 gun halves back together & try it out!
This example was chronographed at 311 fps, it also fired to the left, after the mod
it was consistent at 332 fps & fired straight, the range was dramatically increased
also..