Cavity Preparation Design
Direct Tooth Colored
Restoration
Epita Sarah Pane
Conservative Department
2007
Direct Restorative Materials
• PLASTIC =
readily deformable when first mixed,
and are placed and are placed into a prepared cavity
in a tooth while still in this condition.
General Principles
• Outline Form
• Retention and Resistance Form
• Convenience Form
• Removal of Carious Dentin• Removal of Carious Dentin
• Biologic Form
• Finishing of Enamel Walls
• Preparation Debridement
Retention and Resistance Form
☻Acid conditioning of surface enamel☻Retentive cavity preparation with internal ☻Retentive cavity preparation with internal
details☻Physico-chemical adhesion to some
components of the tooth structure☻Pins and posts☻Combination of 1 to 4
Types of retention
• Chemical = Glass Ionomer• Micromechanical = composite resin• Micromechanical = composite resin• Macromechanical / mechanical = amalgam
GIC : Adhesion is dictated by:
• Use of high powder:liquid ratio• Use of high powder:liquid ratio• Conditioning to remove smear layer• Maintenance of the water balance during setting
• MICROMECHANICAL ADHESION
BETWEEN COMPOSITE RESIN AND
ENAMEL IS
–The strongest adhesion –The strongest adhesion
available
–Dependent upon the strength
of surrounding enamel
Guidelines• No prescribed cavity form required• Important:
the best and the strongest bond is obtained between composite resin andobtained between composite resin and
enamel, it is desirable to maintain anenamel margin around the full
circumferential of the lesion.
• Basic requirements:
1. An internal cavity form should be rounded to avoid incorporation of stress point
2. Bevel enamel margins to enhance the
seal between C.R and enamel
3. Where esthetic is important enlarge the bevel to provide a smooth transition of C,R. to the tooth structure
4. Do not place a bevel on occlusal margins to avoid
allowing thin sections of the restoration to come
under occlusal load
5. Do not place a bevel on the gingival margin
of a proximal box if it is in dentin
6. Access to a proximal lesion on an anterior tooth should be from
the lingual to preserve the facial tooth structure and maintain
esthetic.
Bevel
• Partial Bevel
• Long Bevel
• Hollow ground Bevel
• Scalloping the margins• Scalloping the margins
• Skirting
Differences amalgam – direct tooth colored
materials
• The intercuspal width of preparation of direct tooth colored materials may be as direct tooth colored materials may be as small as 1/5 the intercuspal distance
• In preparations for direct tooth colored materials, internal line and point angles may are extremely rounded, especially if they are in enamel
• If anatomically, cariogenically, and mechanically possible, surrounding walls and/or pulpal and gingival floors could all be in enamel in preparations for dtcm.be in enamel in preparations for dtcm.
• Surrounding walls of floors having dentinal components may accommodate dentinal grooves as reciprocating and auxiliary means of retention.
• In dtcm, undermined enamel may be retained.
• Unlike preparation of amalgam, these preparations do not require a reverse preparations do not require a reverse curve at the occluso-proximal juncture.
• For thinned cuspal elements circumferential skirting is indicated.
• Dentinal preparation for dtcm should always be mortise shaped
• Peripheral portions of enamel walls to be etched should be beveled.
• Soucer-shaped Class II preparations for dtcm could be used if the lesion is continued to could be used if the lesion is continued to enamel with minimal, forward dentinal involvement at its center.
• When restoring with dtcm, the preparations should allow for contact area to remain totally or partially in tooth structure.
Class III
• Design 1 (conventional labial
approach)
– Indications:• Proximal surface lesion in anterior teeth, except the distal of
cuspid, where decay is extending more labially than lingually, and involving part of the labial embrasure.
• Class III in labio-verted rotated teeth.• Direct loading of the restorations cannot be avoided.• Distal part of the cuspid, if part of the contact area remains in
tooth structure
• Design 2
(conventional
lingual
approach)
– Indications:– Indications:• Preferred for all
Class III lesions
– General shaped
• Design 3 ( without labial & lingual
approach)
– Indications:• The entire labial or lingual wall is lost during
access or for cariogenic reasonsaccess or for cariogenic reasons• The incisal angle is approached too closely by the
incisal margin• Distal of cuspids• The remaining labial or lingual wall should be bulky
enough to accommodate a retentive groove
• Design 4 ( both labial & lingual
approach)
– Indications:• Decay extend labially and lingually brings the • Decay extend labially and lingually brings the
margins to corresponding embrasures• There has been partial and complete loss of labial
an d/or lingual walls• There are pronounced labial and/or lingual
embrasures facilitating two-way access• There is a diastema or spacing between teeth
• Design 5 ( saucer shaped)
– Indications:• Conditioned enamel and sometimes treated dentin
will be the principle means of retentionwill be the principle means of retention• Caries control measure, preparatory to permanent
restorative treatment• Deciduous or young permanent teeth• Rampant lesion with extensive surface
decalcification
Class IV
• Design 1 (conventional design)
– Indications:• After the removal of diseased tooth structure, bulky
labial and lingual walls should connect with a labial and lingual walls should connect with a gingival floor
• Incisal angle involvement in the preparation is very limited, almost to the corner only
• Teeth have normal occlusal contact during centric and excursive relation of the mandible
• Thick labio-lingually
• Design 2 (labial and/or lingual approach
conventional design)
– Indications:• Incisal angle loss is substantial• Incisal angle loss is substantial• The entire labial and/or lingual walls are lost• The labial and/or lingual walls are formed
completely of unsupported enamel• The restoration will be directly loaded• Not to be used in the distal of cuspids
• Design 3 (unilateral angle involvement)
– Indications:• The defect involves more of the incisal ridge than
the proximal surfacethe proximal surface• Young teeth with large pulp chambers• Not indicated for distal of cuspids if contact in tooth
structure is lost
• Design 4 ( bilateral angle involvement)
– Indications:• All indications for design 3• The incisal defect is larger than the proximal defect• The incisal defect is larger than the proximal defect
– General shape and location of margin (A, B, C)
Class V
• DESIGN 1 (MORTISE SHAPED
PREPARATION)
– Indication• This is a conventional indicated design• This is a conventional indicated design
– General shape
• DESIGN 2 (NON-MORTISE SAUCER
SHAPED)
– Indications:• It is used for erosion and abrasion lesions where
the teeth are very sensitive and cavity preparation may increase that sensitivity
– General shaped and location of margin