Download - DOCUMENTATION FOR QUALIFICATION SYSTEM
Documentation for qualification system
COMPRESSORS – MAINTENANCE, REPAIR
Slovenské elektrárne, a.s., sídlo: Mlynské nivy 47, 821 09 Bratislava 2, Slovenská republika, IČO: 35 829 052, Obchodný register Okresného súdu
Bratislava I, Oddiel: Sa, Vložka číslo:2904/B
DOCUMENTATION FOR QUALIFICATION SYSTEM
MATERIAL GROUP: COMPRESSORS – MAINTENANCE, REPAIR
MERCHANDISING GROUP INTERNAL CODE: MM20300
New code according to registration at myHome: MMIM03
version no. 2 dated 16.12.2016
Slovenské elektrárne, a.s., Mlynské nivy 47 821 09 Bratislava 2 entered in the Commercial Register, District Court Bratislava I, Section: Sa, file no.: 2904/B; Corporate reg. no.: 35 829 052, VAT ID: SK2020261353
Contact: [email protected]
Documentation for qualification system
COMPRESSORS – MAINTENANCE, REPAIR
Slovenské elektrárne, a.s., sídlo: Mlynské nivy 47, 821 09 Bratislava 2, Slovenská republika, IČO: 35 829 052, Obchodný register Okresného súdu
Bratislava I, Oddiel: Sa, Vložka číslo:2904/B
1. Introduction
1.1. This document specifies the basic qualification requirements that applicants must meet in order to become qualified suppliers to SE, a.s for contracts from the field of COMPRESSORS – MAINTENANCE, REPAIR. An applicant shall be successful in qualification (the applicant’s inclusion in the system) if it fulfils all requirements for qualification, as set out in the General Qualification System Conditions, in the manner set out therein, as well as fulfilling the requirements set out in this documentation. The General Qualification System Conditions are in the form of a separate document. Arrangements contained in this documentation take precedence over those in the General Qualification System Conditions.
1.2 The qualification system is maintained for the individual branches of Slovenské elektrárne:
Slovenské elektrárne, a.s. plant Bohunice nuclear power plant, 919 31Jaslovské Bohunice (EBO) Slovenské elektrárne, a.s. plant Mochovce nuclear power plant, 935 39 Mochovce (EMO) Slovenské elektrárne, a.s. plant Nováky power plant, 972 43 Zemianske Kostoľany (ENO) Slovenské elektrárne, a.s. plant Vojany power plant, 076 73 Vojany (EVO) Slovenské elektrárne, a.s. plant Trenčín hydropower plant, Soblahovská 2, 911 69 Trenčín (VET)
1.3 The qualification system is divided into the following categories:
A) Piston compressors (EMO, EBO, VE, EVO)
B) Screw compressors (ENO, EMO, EBO, VE, EVO, ENO)
C) Turbocompressors (EBO, EMO, ENO)
D) Blowers (EMO, EBO, VE)
E) Vacuum pumps, air dryers and vacuum cleaners (EMO, EBO, ENO)
1.4 A applicant will be included in the appropriate category for which it has submitted an application, provided that the submitted documentation specified in point 3 is assessed as satisfactory for the selected category.
Documentation for qualification system
COMPRESSORS – MAINTENANCE, REPAIR
Slovenské elektrárne, a.s., sídlo: Mlynské nivy 47, 821 09 Bratislava 2, Slovenská republika, IČO: 35 829 052, Obchodný register Okresného súdu
Bratislava I, Oddiel: Sa, Vložka číslo:2904/B
2. Description of the subject matter of the material group
The subject matter includes the following activities:
Maintenance, repairs and servicing of compressors, turbocompressors, blowers, vacuum pumps, air dryers and dehumidifiers in the scope set out for the individual categories, including the supply of replacement parts. This material group does not include repairs to portable compressors.
Types of servicing: 1. Regular servicing 1x annually
2. Fault servicing (repairs) – beginning work within 24 hours of call (by phone or e-mail)
3. Overhauls – beginning work at an agreed time
The technical specifications for each contract, containing detailed technical descriptions, a definition of the timetable and all other particulars required for performing the requested service will be available at the time of each competition in the application phase. The supplier shall perform activities itself, according to work orders (orders) and technological procedures issued or approved by SE. The activities shall be performed at the power plant premises. In justified cases the work shall be performed at the supplier’s premises.
In the case of supplies of replacement parts, it is required that the material fulfils the quality and parameters given in the technological regulations and that the material is documented with material quality certificates, evidenced by the attachment of certificates.
2.1. Category A) Piston compressors
Types of compressors: EMO: DVK, JSK, SM001, SF1, VM
EBO: 1JSK-50 ,2JSK-75, 2DVK-120, LT-7 Atlas Copco, LT-20 Atlas Copco, 1SK- 85-2P, 4V2 (VTK) EVO: ČKD – JVK 120PKO, ORLÍK PKS 28-185, ORLÍK PKS 51-300 VE: Listed in Annex 2.
Activities on this equipment include:
Disassembly of the compressor and accessories
Checking and cleaning the individual parts of the compressor
Replacing damaged and worn parts
Lubricant exchange (grease, oil)
Reassembly of the compressor and accessories
Compressor axle alignment
Compressor test run verifying functionality
2.2. Category B) Screw compressors
Types of compressors:
EMO: DZK
EBO: ZR450 (NTK) Atlas Copco, SF 4-8 SKID
Documentation for qualification system
COMPRESSORS – MAINTENANCE, REPAIR
Slovenské elektrárne, a.s., sídlo: Mlynské nivy 47, 821 09 Bratislava 2, Slovenská republika, IČO: 35 829 052, Obchodný register Okresného súdu
Bratislava I, Oddiel: Sa, Vložka číslo:2904/B
ENO:
designation type pieces
SK 1,2, DZK 255/163-6 2
Sk 3,4 SCK 151-8 2
SK 5 GA 160 VSD 1
SK 6 GA 315 VSD -A-P-50 1
Atlas Copco GA 30 - 10 PACK 2
Atlas Copco ZR - 4-51 EELEK PACK 2
Atlas Copco ZT 90 2
Atlas Copco ZE - 132 3
Atlas Copco GA - 37 3
Atlas Copco SF - 8T 2
Aerzen Aerszen VM 410 -2 1
EVO:
Air-cooled TAMROTOR M 160/7,5, TAMROTOR M 160/4, TAMROTOR FL 55/10EA, BOGE 125 SLF
Water-cooled ATLAS COPCO ZR 250 – 7,5, ATLAS COPCO ZA 500 – 3,5
VE: Listed in Annex 2.
Activities on this equipment include:
compressor test run (activity of separator, agitation, noise) and, where necessary, defect removal
check of control unit
check of the state and setting of the compressor suction valve in connection with operation in a light-load and full-load, including setting power control depending on the desired air pipe pressure
check of the safety valve function
check of automatic start-up of the compressor in the case of a pressure drop in pipes and vice versa, i.e. check of automatic shutdown in the event of no consumption of compressed air (repair or re-setting of the automatic mechanism if necessary)
check that there is no backflow blow ofoil vapours into the compression suction (removal of defects if necessary)
check of the tightness of the oil circuit, tightening connections, resealing if necessary
check the tightness of the compressor air piping, including the tightness of individual elements and tubes in the regulation circuit, tightening joints, or resealing and replacing gaskets
cleaning the solenoid ventral for ducting away condensate
oil exchange in the case of it reaching the end of its useful life or in the case of excessive dirt
exchange of filters and separator in the case of their reaching the end of their useful life or in the case of excessive dirt
regreasing all moving parts and all lubrication points on the compressor, including its electric motor
exterior cleaning of the oil cooler and cooler
checking the tensioning of belts, tightening them as necessary, or replacement if they are in a compressor
check of electrical equipment on the compressor, tightening all screws and clamps, including the contactor
Documentation for qualification system
COMPRESSORS – MAINTENANCE, REPAIR
Slovenské elektrárne, a.s., sídlo: Mlynské nivy 47, 821 09 Bratislava 2, Slovenská republika, IČO: 35 829 052, Obchodný register Okresného súdu
Bratislava I, Oddiel: Sa, Vložka číslo:2904/B
axle alignment on the compressor
check of electrical current upon starting up the compressor, during operation, at light-load and full-load
2.3. Category C) Turbocompressors
Types of compressors:
EMO: 6ZL-40/48
EBO: YORK - YKCNCH25CUC, 6ZL-40/48
ENO:
designation type pieces
TK 1,2 8 RMA 50A 2
Activities on this equipment include:
Disassembly the turbocompressor
Checking and cleaning the individual parts of the compressor
Replacing damaged and worn parts
Lubricant exchange (grease, oil)
Reassembly of the turbocharger
Inspection run to verify the functionality of the turbocharger
2.4. Category D) Blowers
Types of blowers:
EMO: AGKRV, DT, ARF, DI
EBO: 1A21-30-4A, 1A24-30-4A, E-21-50-4A, DT30-EJABO-2, 1G22-50-2V
EVO:
K 121 R-LP with belt transmission
K 170 R-LP with belt transmission
ROBOX LRB 41/2P with belt transmission
ROBOX LRB 80/3P with belt transmission
ROBOX LRB 100/4P with belt transmission
ROBUSCHI RBS 175V with belt transmission
LUTOS DITL 50 T with belt transmission
LUTOS DITL 66 T with belt transmission
LUTOS DITL 70 T M110 with belt transmission
AERZEN GM 150S with belt transmission VE: Listed in Annex 2. Activities on this equipment include:
Disassembly the blower
Documentation for qualification system
COMPRESSORS – MAINTENANCE, REPAIR
Slovenské elektrárne, a.s., sídlo: Mlynské nivy 47, 821 09 Bratislava 2, Slovenská republika, IČO: 35 829 052, Obchodný register Okresného súdu
Bratislava I, Oddiel: Sa, Vložka číslo:2904/B
Checking and cleaning individual parts of the blower
Replacing damaged and worn parts
Lubricant exchange (grease, oil)
Reassembly of the blower
Axle alignment on the blower
Test run of the blower to verify functionality 2.5. Category E) Vacuum pumps, air dryers and vacuum cleaners
Types of vacuum pumps and dryers:
EMO: RV, H-40, BPP, VS50
EBO: 40/2, RV 120, Vacuum pump EDWARDS, 25-UVHJ, 50-UVHJ, 2BV5 111-OHH3,
ENO:
Designation of dryers type pieces
SV1 BD630 1
Atlas Copco CD 75 1
Atlas Copco MD 4 1
Atlas Copco MD 200 1
Vacuum equipment: PVZ 2-1
EVO:
Refrigerated air dryer ATLAS COPCO FD 1200 W
Refrigerated air dryer ATLAS COPCO FD 1600 W
Absorption air dryer ATLAS COPCO CD 140-11
Refrigerated air dryer MTA type DMN 250
Absorption air dryer MTA type DA005
Refrigerated air dryer MTA typ DMN 200
Absorption air dryer MTA typ DA007
Absorption air dryer MTA typ NST 140
Desiccant dehumidifier Munters MX 2700
Desiccant dehumidifier Munters ML 1350
Desiccant dehumidifier Munters ML 1100
Adsorption dehumidifier HB Cotes HBC CR 400BT
Adsorption dehumidifier HB Cotes HBC CR 3800T
Activities on this equipment include:
Disassembly of the vacuum pump
Check and clean the individual parts of the vacuum pump
Replacing damaged and worn parts
Lubricant exchange (grease, oil)
Reassembly of the vacuum pump
Test run of the vacuum pump to verify functionality
Check of the activity of air dryers or dehumidifiers, cleaning of components, or replacement;
Check of the electrical equipment of dryers or dehumidifiers
Documentation for qualification system
COMPRESSORS – MAINTENANCE, REPAIR
Slovenské elektrárne, a.s., sídlo: Mlynské nivy 47, 821 09 Bratislava 2, Slovenská republika, IČO: 35 829 052, Obchodný register Okresného súdu
Bratislava I, Oddiel: Sa, Vložka číslo:2904/B
Check of the overall tightness, resealing if necessary, or replace gaskets
Checking desiccant cartridges, filter cartridges and filters on dryers or dehumidifiers
2.6. Conditions for performing works in the controlled area of a nuclear power plant
In the case where performance of the contract is to occur in the controlled area of a nuclear power plant, the following certificates for all personnel must be submitted for the entry of workers based on the contract concluded with the successful applicant:
- certificate on medical and mental fitness and integrity pursuant to Act no. 541/2004, but on the
peaceful use of nuclear power (the Atomic Act) § 26(5),
- proof of integrity – a valid excerpt from criminal records not more than 3 months old
- proof of medical fitness – a medical confirmation issued by a doctor authorised to issue such
confirmations
- proof of mental fitness – a confirmation on passing psychological tests, issued by a psychological
workplace authorised to issue such confirmations
- certificate on fitness pursuant to Act no. 335/2007 Coll. on the protection, promotion and
development of public health under § 15(1)(c), (d) and (e) in accordance with § 45 of the Act,
required for the 1st category: nuclear power plants – primary circuit.
3. Qualification conditions
3.1. The basic requirements that the applicant must fulfil for the purpose of meeting the qualification conditions are broken down into the following:
conditions regarding personal status;
conditions regarding economic and financial standing;
conditions regarding technical and professional capacity, quality assurance.
conditions regarding personal status, economic and financial standing, as well as the method of submitting, proving and documenting the qualification conditions of applicants for this qualification system are given in the General Qualification System Conditions.
3.2 Conditions concerning technical and professional capacity, quality assurance
The applicant shall prove its technical and professional capacity and quality level for performing contract by submitting the following documents. An overview of documents required for individual categories is given in Annex 1. The required documents must be entered in the myHome system.
a) List of contracts (references) - at least one over the past 3 years carried out in a similar energy, petrochemical or similar sector. As regards the performance provided the applicant must present a confirmed reference, together with contact details to a person for verifying the reference.
Information on the contracts performed (references) shall be provided by the applicant on the form sheet, the specimen of which will be available after registration for the relevant qualified material group in myHome. Performance of every contract must be confirmed by the customer, or a document evidencing
Documentation for qualification system
COMPRESSORS – MAINTENANCE, REPAIR
Slovenské elektrárne, a.s., sídlo: Mlynské nivy 47, 821 09 Bratislava 2, Slovenská republika, IČO: 35 829 052, Obchodný register Okresného súdu
Bratislava I, Oddiel: Sa, Vložka číslo:2904/B
the performance of the subject matter of the contract (contract, acceptance protocol, invoice… ). SE shall be entitled to verify with the customers the facts indicated in the List of contracts.
b) Quality certificate for the corresponding subject of qualification, issued by an independent institute
according to the requirements of EN ISO 9001 or other document (Quality Manual) proving that the applicant has a management system in place under the requirements of EN ISO 9001.
c) OH&S management system certificate according to OHSAS 18001 standards. When candidate doesn´t have certified OH&S management, he has to fill in the questionnaire „HSE checklist“ which is stated in the attachment of this documentation, by which SE, a.s. consider OH&S management functionality. Completed questionnaire together with the documents and information required in the questionnaire the candidate submits in myHome on the form „Documentation“ in the second part of the qualification questionnaire. Candidate has to achieve 14 points from the total 28 points by the HSE checklist evaluation for qualification.
d) The applicant’s organisational chart indicating the number of own employees, i.e. engaged in employment or other similar relationship, separately for each organisational unit and for individual areas within the competence of the given unit.
e) List of names of all professions available to the applicant for performing contract the qualification system. The list must contain a number of employees and information on the legal relationship in which such staff is in respect of the applicant (employee, subcontractors, individual - entrepreneur). Professional certificates for individual professions (with the exception of the profession of the fitter foreman) shall be submitted by all employees prior to signing the contract, or, if relevant, prior to the start of works. In order to satisfy the qualification conditions for individual categories the applicant must have available the following professions. The minimum required number of workers for the relevant category is given in Annex 1.
authorised safety technician – valid certificate under § 24 of Act no. 124/2006 Coll. on occupational health and safety, and who will concurrently perform occupational safety coordination pursuant to § 6 Slovak Government Regulation No. 396/2006 Coll.;
site supervision – valid certificate under the provisions of § 46b of Act no. 50/1976 Coll. on zoning and the building code (the Building Act), as amended, in relation to §1d of Act no. 138/1992 Coll. on the authorised architects and civil engineers, as amended, for the management of structures and performance of site supervision.
welders – welder certificate for the following types of welding:
- manual arc welding (111) - oxy-fuel welding (311)
load binders – valid binder certificates for binding the loads;
locksmiths with vocational certificate
Fitter foreman – the applicant shall attach to the list of the names of professions a professional CV and documents proving the training of workers with the profession of a fitter foreman, proving the professional experience and expertise in this profession. If such employee is not employed by the applicant, the applicant will also attach a document (e.g. agreement) proving that the applicant has the worker available for the performance throughout the qualification term.
All the employees must be familiarised with the performance of the works pursuant to § 20 of Decree no. 508/2009 Coll.
Documentation for qualification system
COMPRESSORS – MAINTENANCE, REPAIR
Slovenské elektrárne, a.s., sídlo: Mlynské nivy 47, 821 09 Bratislava 2, Slovenská republika, IČO: 35 829 052, Obchodný register Okresného súdu
Bratislava I, Oddiel: Sa, Vložka číslo:2904/B
f) List of equipment and work equipment to ensure the performance with the valid inspections and tests.
The list must contain the equipment’s name, description and relation in respect of the applicant (ownership, operative leasing, rent). SE shall be entitled to verify the facts indicated in the list by way of an audit at the supplier or owner. In the list the applicant shall indicate that in the case of performing an audit the applicant agrees to it. In order to satisfy the qualification conditions for individual categories that applicant must have available the following facilities and equipment. The required quantity of equipment for the relevant category is given in Annex 1.
Documentation for qualification system
COMPRESSORS – MAINTENANCE, REPAIR
Slovenské elektrárne, a.s., sídlo: Mlynské nivy 47, 821 09 Bratislava 2, Slovenská republika, IČO: 35 829 052, Obchodný register Okresného súdu
Bratislava I, Oddiel: Sa, Vložka číslo:2904/B
ANNEX 1: OVERVIEW OF DOCUMENTS
Category A
Piston compressors
B Screw
compressors
C
Turbocompressors
D
Blowers
E
Vacuum pump, air
dryers, vacuum cleaners
Conditions for technical and professional capacity*
list of contracts (references) - of
repairs of facilities by category
yes
yes
yes yes yes
Organisational chart
yes
yes yes yes yes
List of professions
Authorised safety technician
yes (1)
yes (1)
yes (1)
yes (1)
yes (1)
Fitter foreman - - yes (1) - -
Welder yes (2) yes (2) yes (2) yes (2) yes (2)
load binder yes (2) yes (2) yes (2) yes (2) yes (2)
locksmith yes (6) yes (6) yes (6) yes (6) yes (6)
List of mechanical, technical and software
equipment yes yes yes yes yes
Quality management system
yes yes yes yes yes
OSH management system
yes yes yes yes yes
* The figure in brackets indicates the number of references/persons/equipment required for qualification.
Documentation for qualification system
COMPRESSORS – MAINTENANCE, REPAIR
Slovenské elektrárne, a.s., sídlo: Mlynské nivy 47, 821 09 Bratislava 2, Slovenská republika, IČO: 35 829 052, Obchodný register Okresného súdu
Bratislava I, Oddiel: Sa, Vložka číslo:2904/B
Annex 2: List of compressors installed at the hydropower station
Power plant Manufacturer Compressor type Compressor
kind Number
(pcs) serial no. motor type
motor output (kW)
VE Domaša ČKD Praha V2-60/130 EKO piston 1 52066 AD644 10
VE Domaša ČKD Praha 2-DVK-120 EKO piston 2 6168
6170 E160M06 7.5
Ružín I Neumann&Esser BV 35-270/180/85 piston 2 900247A, 900247B ACM250M 55
Ružín I Atlas Copco ZE 230 rotational 2 AIF.071440,
AIF.071469 1LA5206-2AA61-ZW00 33.3
PVE Dobšiná ČKD 3TWK120 piston
1 110 F225M08 00 22
PVE Dobšiná ČKD 2JVK 120 EKO1 piston
1 19263 F180L06 318 15/18
PVE Dobšiná ČKD 2JVK 120 EKO1 piston
1 19262 F180L06 318 15/18
MVE Krompachy ČKD 1JSK 65 piston
1 6365 1JSK 63 2.28
PVE Č. Váh ČKD Praha 4DSK 310.4 piston 3 2ASR355-8 160kW
PVE Č. Váh ČKD Praha 3TWK-120 piston 11
F225M26 40kW
Liptovská Mara ČKD Praha 3TVK 120 piston
3 F225M06 30
Liptovská Mara ČKD Praha 3TVK 120 piston
1 B3225M-30 30
Liptovská Mara ČKD Praha 2 DVE 120-1 piston
1 F 160 M04 11
Liptovská Mara COMPAIR CYCLON 105 screw 2 F160 2960 6.88
Bešeňová Atlas Copco LT3- 30 CVBM piston
1 WCF 445403 LS100LT 2.2
Orava ČKD Praha V4-1500 piston
1 98520 MEZ 1P10BV6 30
Orava ČKD Praha 3TWK120 piston
1 602 MEZ F225M08 22
Documentation for qualification system
COMPRESSORS – MAINTENANCE, REPAIR
Slovenské elektrárne, a.s., sídlo: Mlynské nivy 47, 821 09 Bratislava 2, Slovenská republika, IČO: 35 829 052, Obchodný register Okresného súdu
Bratislava I, Oddiel: Sa, Vložka číslo:2904/B
Tvrdošín Boge SRH 940 piston
1 5054534 132S02 7.5
Krpeľany Atlas Copco
LT20-30UV BM400/50
piston 1 WCF429445 3fLS160LRT 400V/50Hz
15
Sučany Atlas Copco
LT20-30UV BM400/50
piston 1 WCF429444 3fLS160LRT 400V/50Hz
15
Lipovec Atlas Copco
LT20-30UV BM400/50
piston 1 WCF429446 3fLS160LRT 400V/50Hz
15
Hričov COMPAIR Reavell, typ 5213
piston 1 CE 406517/147 160 MH 11
Hričov COMPAIR Reavell, typ 5213
piston 1 CE 406517/148 160 MH 11
Hričov ČKD Praha 3TWK- 120
piston 1 231 F8 108 22
Hričov ČKD Praha 3TWK- 120
piston 1 340 F225 MOC 30
Hričov COMPAIR Cyklon 105 screw 1 F160/0382 2900RPM 5.5
Hričov COMPAIR Cyklon 105 screw 1 F160/0387 2900RPM 5.5
Mikšová ČKD 2DSK piston 1 MAF315M-10 75
Mikšová Atlas Copco LT20-30 UV BM piston 2 WCF418578 WCF408289
LS160LRT 15
P.Bystrica ČKD Praha 3TWK-120 piston 2 1205 727
F225M0600 30
P.Bystrica ČKD Praha V260/100BM piston 2 1645 1790
AF422/4A 3
Nosice ČKD Praha 3 TWK-120 piston 1 325 F8106 00 30
Nosice ČKD Praha 3 TWK-120 piston 1 327 F8106 00 30
Nosice ČKD Praha 3 TWK-120 piston 1 506 F225M06 00 40
Ilava COMPAIR Reavell, typ 5209 piston 2 5209 391 5209 392
WD160M 12.7
Ilava CKW 2V1-52-D25 piston 2 4287/1105 4287/1062
WD160M 3
Ladce ČKD PRAHA 3TWK 120 piston 1 P 63 E225M08/23 22
Ladce ČKD PRAHA MSK 145 piston 1 D15B-8NC 8
Documentation for qualification system
COMPRESSORS – MAINTENANCE, REPAIR
Slovenské elektrárne, a.s., sídlo: Mlynské nivy 47, 821 09 Bratislava 2, Slovenská republika, IČO: 35 829 052, Obchodný register Okresného súdu
Bratislava I, Oddiel: Sa, Vložka číslo:2904/B
Dubnica ČKD Praha 3 TWK 120 piston 1 139 MEZ Frenštát typ F8 106 00
30
Dubnica ČKD Praha 3 TWK 120 piston 1 243 MASINEXPORT RUMANIEN UVEB typ ASL 250 S60/6
30
Trenčín ATMOS- ŽANDOV V4-900 piston 1 48004 1H8AV8003 13
Trenčín ČKD-PRAHA 3TWK120 piston 1 566 F225M08 22
VE Kostolná ČKD Praha 3TWK120EKO1 piston 1 1071/1987 F225M08 306 22
VE Kostolná ČKD Praha 3TWK120EKO1 piston 1 1192/1991 F225M06 352 36
VE Kostolná ATMOS n.p. V4- 1600 piston 1 68007 VR122-6 30
VE Kostolná IKOV dotláčanie vzduchu do vodárne
S112 piston 1 /0069/ 2AP80-2S 0.75
N.Mesto ČKD Praha 3TWK120EKO1 piston 1 1197 F225M06 352 30
N.Mesto ČKD Praha 3TWK120EKO1 piston 1 1069 F225M06 367 30
H.Streda ČKD Praha 3TWK120EKO1 piston 1 1212 F225M06 339 30
H.Streda ČKD Praha 3TWK120EKO1 piston 1 1214 F225M06 339 30
Madunice ČKD 3TWk-120EKO I piston 3 795 798 813
F 225 MO6 30
Madunice ORLIK 3JSK75-2 piston 2 6780 6788 4AP132M-4 7.5
Madunice FPZ-Effepizeta SCL15DH blower 1 82637 EMG71/2 0.55
Kráľová Orlík EKA 51 piston 1 140340 2A132S2-2xMk1B3 8.6
Kráľová Orlík 1JSK-75 piston 1 9183 AP112M-2S 4
Kráľová ČKD Praha 3TWK120-1 piston 3 155/1982 163/1982 160/1982
F225M06 40
Kráľová VKDI Orlík 2JSK-75 piston 1 1774 AP132S-2 7.5
Veľké Kozmálovce
ČKD Žandov 20VK120FK01 piston 1 6381-1994 C160M02 15