Easy-To-Work-With™
Wood FinishingSelection Guide
The World Leader In Wood Finishing Equipment
Introduction The purpose of this guide is to bring a little science to the marvelous art of wood
finishing. We visited many of the best wood finishing shops and interviewed a number
of outstanding wood coating suppliers to develop this wood finishing guideline. In each
interview, we asked, “What is the best finishing equipment for your shop?”.This guide is
their response.
We are confident that if you follow the suggestions made in this guide you will likely see
an increase in your finish quality and a reduction in your finishing costs. We hope you
enjoy reading this guide, as much as we enjoyed creating it. It’s an outstanding reference
guide.
Dye Stains (NGR) NGR, Toner, Shading, SAP, Equalizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Pages 2 - 3
Other Stains Wiping Stain, Glaze, Spray Stain, Spray & Wipe Stain, Filler . . . . . . . . . . .Pages 4 - 5
Sealers & Primers Washcoat, Sealer, Primer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Pages 6 - 7
Topcoats Nitrocellulose (NC), Post-Cat, Pre-Cat, Urethane . . . . . . . . . . . . . . . . . . . . .Pages 8 - 9
Starter Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Pages 10 - 11
The Power of Airmix® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Pages 12 - 13
Accessories Airspray, HVLP, Airmix® and General Accessories . . . . . . . . . . . . . . . . . . .Pages 14 - 19
Special Applications Adhesive, 2K, Automatic Application Equipment, Paint Kitchens . . . . . . . .Page 20 - 21
Index
Dye Stains (NGR)
Low Volume Shops
Gun
Solvent Based
Solvent Based
*At regulator with gun triggered
*At regulator with gun triggered
*At regulator with gun triggered
M22HPAA
M22HTIG (LVLP)
15
15
Nozzle
EN2
EP5
40 to 70 psi
40 to 70 psi
1/4” - 25 ft
1/4” - 25 ft
136-145-212
136-131-114
Aircap Air Pressure* Air Hose Gun Only Part Number
Medium Volume Shops
Gun
SmallCompressor
M21/2 BASIC LP 12
Nozzle
LP 3 25 to 55 psi 1/4” - 25 ft 668-222-013
Compliant HVLP M22HTIP (HVLP) 12 E3 35 to 67 psi 5/16” - 25 ft 668-222-014
Aircap Air Pressure* System Part Number
10 to 12 psi
10 to 12 psi
Fluid Pressure Air Hose
1/4” - 25 ft
1/4” - 25 ft
Pressure Pot - 2.5 Gallons
Pressure Pot - 2.5 Gallons
Fluid Hose Feed System
High Volume Shops
Very High Volume Shops
Gun
High ProductionSingle Color
M22HTIP (HVLP)
M22HTIP (HVLP)
12
12
Nozzle
E3
E3
35 to 67 psi
35 to 65 psi
5/16” - 25 ft
5/16” - 25 ft
668-751-022
668-751-000High ProductionSingle Color
Aircap Air Pressure* System Part Number
10 to 12 psi
10 to 12 psi
Fluid Pressure Air Hose
1/4” - 25 ft
1/4” - 25 ft
PMP Pail Mount
PMP Pump
Fluid Hose Feed System
This group of stains can also be called NGR (non-grain raising) stains. It
includes toners, shaders, sap and equalizers. They are generally used to
equalize the color of furniture either in certain areas or over the entire piece.
They are typically 0.5% to 3% dyes and the rest is alcohol or acetone.
Although Airmix® is sometimes used with these coatings, it is usually easier
to use low pressure spray guns, such as HVLP, LVLP or conventional spray.
The dye in this coating will remain suspended without agitation
and hence does not need agitation. However, check with your paint
supplier. If it contains pigment, you will need to add agitation.
These shops will require a detailed review of fluid handling methods
before recommendations can be made. Please contact a Kremlin
representative.
Water Based M22HTIG (HVLP) 15 E5 45 to 67 psi 5/16” - 25 ft 136-131-104
M22HTIP (HVLP) 12 E3 35 to 65 psi 5/16” - 25 ft 668-763-200High Production andFast Color Change
10 to 12 psi 1/4” - 25 ft 02-75 Pump
ALL PACKAGES INCLUDE ONE (1) GUN ONLY.
DY
E S
TAIN
S (N
GR
)
3
02-75 System(Cart Extra)
M21/2 LP Basic Gun
M22HTIP Gun(HVLP Compliant)
M22HTIG E5 (HVLP Compliant)M22HTIG EP5 (LVLP)Gravity Guns
M22HPAASiphon Feed Gun
Pressure Pot System
PMP-150 System(Cart Extra)
Other Stains This group is all non-dye stains such as glaze, spray, spray and wipe, wiping
stains and filler. They give the wood its beautiful color. They are typically a
combination of dye, binder, pigment and solvent. The solids content can vary
from as low as 4% for spray stains to as high as 65% for fillers.
Airmix® is highly recommended for these coatings since it delivers a uniform coat
with minimal overspray and waste. This coating will settle quickly and requires,
as a minimum, agitation and ideally, circulation.
1. Always wipe the fillers across the grain to maximize the effect.
2. Always wipe stains in a circular motion and end by wiping with the grain.
Low Volume Shops
Gun
Airmix® MVX 09 - 094
Tip (see page 15)
BX 16 2 to 6 psi 668-665-625
Aircap Air Pressure(at regulator)
200 to 400 psi
Fluid Pressure Air Hose
3/16” - 16 ft1/4” - 16 ft EZMix Pump
Fluid Hose Feed System
Airmix® MVX 04 - 074 BX 16 15 to 30 psi 668-665-625*200 to 400 psi 3/16” - 16 ft1/4” - 16 ft EZMix Pump
High Volume Shops
Gun Tip (see page 15) Aircap Air Pressure(at regulator) One Gun System Part NumberFluid Pressure Air Hose
Wipe Stain1 Gun Airmix® MVX 14 -094 VX 14 2 to 6 psi 1/4” - 25 ft 668-668-512200 to 400 psi 3/16” - 25 ft 10-25 Pump
Fluid Hose Feed System
Airmix® MVX 14 -094 VX 14 2 to 6 psi 1/4” - 25 ft 668-730-502200 to 400 psi 3/16” - 25 ft 17A Pump
Airmix® MVX 04 -074 VX 14 15 to 30 psi 1/4” - 25 ft 668-668-510200 to 400 psi 3/16” - 25 ft 10-25 Pump
Airmix® MVX 04 -074 VX 14 15 to 30 psi 1/4” - 25 ft 668-730-504200 to 400 psi 3/16” - 25 ft 17A Pump
Medium Volume Shops
Gun
Airmix® MVX 12 - 094
Tip (see page 15)
VX 14 2 to 6 psi 1/4” - 25 ft 668-665-005
Aircap Air Pressure(at regulator) One Gun System Part Number
200 to 400 psi
Fluid Pressure Air Hose
3/16” - 25 ft 10-14 Pump
Fluid Hose Feed System
Airmix® MVX 04 - 074 VX 14 15 to 30 psi 1/4” - 25 ft 668-665-006200 to 400 psi 3/16” - 25 ft 10-14 Pump
Very High Volume Shops
These shops will require a detailed review of
fluid handling methods before recommendations
can be made. Please contact a Kremlin
representative.
1. For agitation see page 18.
2. For circulation see page 16. 10-14 & EZMix are not designed for circulation.
3. For two gun manifold see page 17.
4. For two-way or three-way suction manifolds see page 19.
5. For cart mount options see page 19.
6. For 55 gallon suction rod options see page 19.
7. If stain is abrasive use stainless steel seat insert in Airmix®
Gun, see page 15.
One Gun System Part Number
*You must specify the proper tip for your applilcation when ordering the EZMix system. System comes standard with 09-094 tip.
Wipe Stain
Spray Stain
Wipe Stain
Spray Stain
ALL PACKAGES INCLUDE ONE (1) GUN ONLY.
Wipe Stain1 to 2 Guns
Spray Stain1 Gun
Spray Stain1 to 2 Guns
OTH
ER
STA
INS
5
EZMix System
MVX Gun(HVLP Compliant)
10-25 System(Cart Extra)
10-14 System(Cart Extra)
17A System (Cart Extra)
Sealers&Primers
These coatings consist of sealers, primers and washcoats. The washcoat seals the dye stains from thewiping stains and is typically a reduced topcoat. The sealer typically seals the wiping stains and is also areduced topcoat with sanding aids. The primers are used to seal the wood and usually contain pigment
and sanding agents.
1. Airmix® is highly recommended for these coatings since it delivers a uniform coat with minimal overspray, sanding and waste.
2. This coating will settle quickly and requires agitation.
3. If your facility cannot deliver a consistent minimum 70οF (20οC) paint temperature to the guns, we recommend circulating with paint heaters.
Low Volume ShopsGun
Sealers Airmix® MVX 09 - 094
Tip(see page 15)
BX 16 8 to 15 psi 1/4” - 16 ft 668-665-625
Aircap Air Pressure(at regulator)
System Part Number
400 to 700 psi
Fluid Pressure Air Hose
3/16” - 16 ft EZMix Pump
Fluid Hose Feed System
Solvent
Primers Airmix® MVX 09 - 094 BX 16 12 to 20 psi 1/4” - 16 ft 668-665-625600 to 700 psi 3/16” - 16 ft EZMix PumpSolvent
Washcoats Airmix® MVX 09 - 094 BX 16 4 to 10 psi 1/4” - 16 ft 668-665-625300 to 600 psi 3/16” - 16 ft EZMix PumpSolvent
Coating
Medium Volume ShopsGun
Sealers - 1 Gun Airmix® MVX 09 - 094
Tip(see page 15)
VX 14 8 to 15 psi
Aircap Air Pressure(at regulator)
400 to 870 psi
Fluid Pressure Air Hose
3/16” - 25 ft 10-14 Pump
Fluid Hose Feed System
Solvent / Water
Sealers - 1 or 2 Guns Airmix® MVX 09 - 094 VX 14 8 to 15 psi 400 to 1000 psi 3/16” - 25 ft 20-25 PumpSolvent / Water
Primers - 1 Gun Airmix® MVX 09 - 094 VX 14 12 to 20 psi 600 to 870 psi 3/16” - 25 ft 10-14 PumpSolvent / Water
Primers - 1 or 2 Guns Airmix® MVX 09 - 094 VX 14 12 to 20 psi 600 to 1000 psi 3/16” - 25 ft 20-25 PumpSolvent / Water
Washcoats - 1 Gun Airmix® MVX 09 - 094 VX 14 4 to 10 psi 300 to 600 psi 3/16” - 25 ft 10-14 PumpSolvent / Water
Washcoats - 1 or 2 Guns Airmix® MVX 09 - 094 VX 14 4 to 10 psi 300 to 600 psi 3/16” - 25 ft
1/4” - 25 ft
1/4” - 25 ft
1/4” - 25 ft
1/4” - 25 ft
1/4” - 25 ft
1/4” - 25 ft 20-25 PumpSolvent / Water
Coating
High Volume Shops
1. For agitation see page 18.
2. For circulation and heaters see page 16.
3. For two gun manifold see page 17.
4. For two-way or three-way suction manifoldssee page 19.
5. For cart mount options see page 19.
6. For 55 gallon suction rod options see page 19.
Very High Volume ShopsThese shops will require a detailed review of fluid handling methods
before recommendations can be made. Please contact a Kremlin
representative.
668-665-000
668-770-100
668-665-000
System Part Number
668-770-100
668-665-000
668-770-100
Gun
Sealers - 1 Gun Airmix® MVX 09 - 094
Tip(see page 15)
VX 14 8 to 15 psi
Aircap Air Pressure(at regulator)
400 to 1000 psi
Fluid Pressure Air Hose
3/16” - 25 ft 17A Pump
Fluid Hose Feed System
Solvent / Water
Sealers - 1 or 2 Guns Airmix® MVX 09 - 094 VX 14 8 to 15 psi 400 to 1000 psi 3/16” - 25 ft 20-50 PumpSolvent / Water
Primers - 1 Gun Airmix® MVX 09 - 094 VX 14 12 to 20 psi 600 to 1000 psi 3/16” - 25 ft 17A PumpSolvent / Water
Primers - 1 or 2 Guns Airmix® MVX 09 - 094 VX 14 12 to 20 psi 600 to 1000 psi 3/16” - 25 ft 20-50 PumpSolvent / Water
Washcoats - 1 Gun Airmix® MVX 09 - 094 VX 14 4 to 10 psi 300 to 600 psi 3/16” - 25 ft 17A PumpSolvent / Water
Washcoats - 1 or 2 Guns Airmix® MVX 09 - 094 VX 14 4 to 10 psi 300 to 600 psi 3/16” - 25 ft
1/4” - 25 ft
1/4” - 25 ft
1/4” - 25 ft
1/4” - 25 ft
1/4” - 25 ft
1/4” - 25 ft 20-50 PumpSolvent / Water
Coating
151-730-200
668-780-200
151-730-200
System Part Number
668-780-200
151-730-200
668-780-200
ALL PACKAGES INCLUDE ONE (1) GUN ONLY.
SE
ALE
RS
& P
RIM
ER
S
7
EZMix System
MVX Gun(HVLP Compliant)
20-25 System(Cart Extra)
17A System(Cart Extra)
20-50 System(Cart Extra)
10-14 System(Cart Extra)
Medium Volume ShopsGun
NC, Post-cat, Pre-cat,Waterborne,1 Gun Airmix® MVX 09 - 094
Tip (see page 15)
VX 14 8 to 20 psi 1/4”- 25 ft 668-665-000
Aircap Air Pressure (at regulator)
One Gun SystemPart Number
400 to 870 psi
Fluid Pressure Air Hose
3/16”- 25 ft 10-14 Pump
Fluid Hose Feed System
Solvent/Water
NC, Pre-cat,Waterborne,1 or 2 Guns Airmix® MVX 09 - 094 VX 14 8 to 20 psi 1/4”- 25 ft 668-770-100400 to 1000 psi 3/16”- 25 ft 20-25 PumpSolvent/Water
Coating
Urethane1 Gun Airmix® MVX 09 - 094 VX 14 20 to 35 psi 1/4”- 25 ft 668-665-000600 to 870 psi 3/16”- 25 ft 10-14 PumpSolvent/water
Urethane1 or 2 Guns Airmix® MVX 09 - 094 VX 14 20 to 35 psi 1/4”- 25 ft 668-770-100600 to 1200 psi 3/16”- 25 ft 20-25 PumpSolvent/Water
Topcoats There are a number of different topcoats that one can apply. However, the most common are NC(Nitrocellulose), pre-catalyzed, post-catalyzed and polyurethanes. The solids content of these coatingsrange from as low as 24% for the NC coatings to as high as 78% for the post catalyzed coatings. Post-catalyzed coatings must be flushed every night.
1. Airmix® is highly recommended for these coatings since it delivers a uniformcoat with minimal overspray and waste. In addition, Airmix® increasesproductivity since it can apply more coating per pass.
2. This coating requires agitation.
3. If your facility cannot deliver a consistent minimum 70οF (20οC) painttemperature to the guns, we recommend circulating with paint heaters.
Low Volume ShopsGun
NC, Pre-cat Airmix® MVX 06 - 094
Tip (see page 15)
BX 16 8 to 20 psi 1/4”- 16 ft 668-665-625*
Aircap Air Pressure (at regulator)
System Part Number
400 to 700 psi
Fluid Pressure Air Hose
3/16”- 16 ft
Fluid Hose Feed System
Solvent
Urethane Airmix® MVX 06 - 094 BX 16 20 to 35 psi 1/4”- 16 ft 668-665-625*600 to 700 psi 3/16”- 16 ft Solvent
Coating
High Volume ShopsGun Tip
(see page 15)Aircap Air Pressure
(at regulator)One Gun SystemPart Number
Fluid Pressure Air Hose Fluid Hose Feed SystemCoating
NC, Post-cat, Pre-cat,Waterborne, 2 Guns Airmix® MVX 09 - 094 VX 14 8 to 20 psi 1/4”- 25 ft 151-730-200400 to 1000 psi 3/16”- 25 ft 17A Pump
17A Pump
Solvent/Water
Post-cat 2 to 3 GunsAirmix® MVX 09 - 094 VX 14 8 to 20 psi 1/4”- 25 ft 668-781-200400 to 1000 psi 3/16”- 25 ft 20-50F PumpSolvent/Water
Urethane 1 to 2 GunsAirmix® MVX 09 - 094 VX 14 20 to 35 psi 1/4”- 25 ft 151-730-200600 to 1200 psi 3/16”- 25 ft Solvent/Water
Urethane 2 to 3 GunsAirmix® MVX 09 - 094 VX 14 20 to 35 psi 1/4”- 25 ft 668-780-200600 to 1200 psi 3/16”- 25 ft 20-50 PumpSolvent/Water
Very High Volume ShopsThese shops will require a detailed review of fluid handling methods before
recommendations can be made. Please contact a Kremlin representative.
1. For agitation see page 18.
2. For circulation and heaters see page 16.
3. For two gun manifold see page 17.
4. For two-way or three-way suction manifolds see page 19.
5. For cart mount options see page 19.
6. For 55 gallon suction rod options see
page 19.
EZMix Pump
EZMix Pump
Post-cat,1 or 2 Guns Airmix® MVX 09 - 094 VX 14 8 to 20 psi 1/4”- 25 ft 151-730-200400 to 1000 psi 3/16”- 25 ft 17A PumpSolvent/Water
NC, Pre-cat, Waterborne,2 to 3 Guns Airmix® MVX 09 - 094 VX 14 8 to 20 psi 1/4”- 25 ft 668-780-200400 to 1000 psi 3/16”- 25 ft 20-50 PumpSolvent/Water
ALL PACKAGES INCLUDE ONE (1) GUN ONLY.
*You must specify the proper tip for your applilcation when ordering the EZMix system. System comes standard with 09-094 tip.
TOP
CO
ATS
9
EZMix System
MVX Gun(HVLP Compliant)
20-25 System(Cart Extra)
17A System(Cart Extra)
20-50 System(Cart Extra)
10-14 System(Cart Extra)
Starter Kits Sometimes, we are asked how we should equip an ideal
shop to do all coatings. This is our answer to that
question.
Low Volume Shops
Gun
Dye Stains
Other Coatings
M22HTIG 15E5 (HVLP)
Airmix® MVX with tip 09-094
None
EZMix Pump
Feed System
136-131-104
668-665-625
Kit Part Number
Medium Volume Shops
Gun
Dye Stains
Other Coatings
M22HTIP 12E3 (HVLP)
Airmix® MVX with tip 09-094
Pressure Pot - 2.5 Gallons
10-14 Pump
Feed System
668-222-014
668-665-000
Kit Part Number
High Volume Shops
Gun
Dye Stains
Other Coatings
M22HTIP 12E3 (HVLP)
Airmix® MVX with tip 09-094
PMP-150
17A Pump
Feed System
668-751-000
151-730-200
Kit Part Number
Recommended Accessories
1. Lower Fluid Delivery Spare Tip: 134-506-094 for solvent based coatings.
1. XtraTM Fine finish style Tip: 134-506-092 for water-based, high solids, and polyurethane coatings.
Recommended Accessories
1. Three-way suction manifold for topcoat, sealer and solvent: 669-669-025
2. Two additional suction rods for the three-way manifolds: 049-596-010 (x2)
3. 5 gallon agitator: 668-668-806 (x2)
4. High delivery spare tip: 134-512-114 for solvent based coatings.
5. XtraTM Fine finish style tip: 134-512-112 for water-based, high solids, and polyurethane coatings.
Recommended Accessories
1. Three-way suction manifold for topcoat, sealer and solvent: 669-669-027
2. Two additional suction rods for the three-way manifold: 049-596-110 (x2)
3. Circulation kit and heater for consistent high quality finish and high productivity see page 16.
4. 5 gallon agitator: 668-668-806 (x2)
5. High delivery spare tip: 134-514-114
6. XtraTM Fine finish style tip: 134-512-112 for water-based, high solids, and polyurethane coatings.
STA
RTE
R K
ITS
11
HTIP H3 Gun(HVLP Compliant)
HTIP H3 Gun(HVLP Compliant)
HTIG H5 Gun(HVLP Compliant)
Pressure Pot
PMP System(Cart Extra)
EZMix System
17A System (Cart Extra)
MVX Gun(HVLP Compliant)
10-14 System(Cart Extra)
MVX Gun(HVLP Compliant)
MVX Gun(HVLP Compliant)
The Powerof AIRMIX®
Imagine a spray painting system that eliminates excess overspray, turbulence and bounce-
back. A system that applies an outstanding finish to your parts, not your spray booth.
AIRMIX® virtually eliminates the wasted coatings clogging your spray booth filtration
system and collecting on your conveyor. AIRMIX® is made for industrial users who
require a world class finish and demand high application transfer efficiency.
AIRMIX® is a medium pressure spray process.
The key to its success is its unique atomization
technology as shown in the two diagrams. This
uniqueness delivers a high quality finish and
uniform film build that is not available from other
medium pressure technologies such as
air-assisted airless.
With Airmix®, atomization air is blended with the fluid at the locus of
atomization, which delivers a very controlled balanced spray that
produces a uniform build.
With other medium pressure systems, such as air-assisted airless,
air injected directly into or beyond the locus of atomization creates
excessive turbulence, overspray, coarse particles and a very
uneven film build requiring additional finishing steps.
HVLP Compliant
Xtra™ Series Fine Finish Tips
These tips are specially designed to improve atomization of
polyurethanes, water-based, & high solid coatings. The Xtra™ tips
have been tested and proven at many customer locations &
received great results.
On standard coatings, these tips may also help to further reduce the
amount of atomizing air needed at the gun.
THE
PO
WE
R O
F AIR
MIX
®
13
Paint Velocity - Reduces booth maintenanceThe paint velocity has a direct impact on performance:the higher the velocity, the greater the amount ofoverspray and bounceback, which combine to quicklypollute the booth. As can be seen from the graph on theright, the particle speed with AIRMIX® is much lowerthan with all other systems.
ADVANTAGES OF AIRMIX®
• Controlled atomization and high quality finish• Cleaner environment• Lower solvent emissions• Higher application efficiency for fast production• Enthusiastic operator acceptance• Transfer efficiency eliminates waste and needless
finishing steps
• Quick payback period• Outstanding reliability• Easy Maintenance• Material Savings of up to 35% and more• Up to 50% savings in spray booth waste• Conforms to virutally all regulations• Fast color changes
Transfer Efficiency - Saves on paint costsUsers of Airmix® achieve the highest transferefficiency available. Efficiencies on different types ofmanual spray equipment are:
Air Consumption - Lower energy costsAIRMIX® uses less air for atomization air than any otherhigh quality spray system. AIRMIX® works well withsmaller air compressors, lower production air pressureand lower compressed air volumes. This generatesmajor savings in compressed air cost and reduces aircompressor maintenance.
Fine Atomization - Excellent finishAIRMIX® uses a specially designed aircap to provide asmooth and even finish every time. The aircap helps toevenly atomize the paint as it leaves the fluid tip. Thiseven atomization allows the paint to be broken downinto smaller particles which provides the best coat withminimal defects or orange peel.
PLUS: New MVX Gun offers
unparalleled pattern control
Airmix® has become a standard in the industry byproviding better atomization, producing lower paintvelocities, requiring much lower air consumption andoffering extremely high transfer efficiencies.
The Benefitsof AIRMIX®
Airmix® - superior to conventional, HVLP, air-assisted airless and airless spraying.
Accessories
Airspray / HVLP Accessories
DescriptionPart
A Inline Filter for Product Inlet 129-020-060
B Wall or Table mounting Kit for Gravity Fed Gun 049-221-800
Pack of 10 Replacement Screens 151-399-902
Pack of 10 Seals 149-949-901
M21Part Numbers
129-140-030
049-221-900
151-399-902
149-949-901
M22 Part Numbers
Miscellaneous Accessories
DescriptionItem
0.6 Quart Plastic Cup (Standard) 139-270-200
Pack of 5 Non-Drip Plugs 139-270-210
0.6 Quart “Gray” Plastic Cup (Optional) 139-270-250
Part Number
Pack of 5 Screens for 0.25 qt and 0.6 qt Plastic Cups 139-270-220
Gravity Cups
Description
PMP-150 Pump 144-931-091
02-75 Pump Not Available
EZMix & 10-14 Pumps Not Available
10-25 Pump 146-260-991
Air Motor Seal Kit
Airspray & Airmix® Pump Seal & Repair Kits
A
B
Description
M21 & M21/2 Series Seal Kit (Pack of 3) 129-029-902
M21 & M21/2 Series Repair Kit 129-029-901
M21HTI Series Seal Kit (Pack of 3) 129-080-902
M21HTI Series Repair Kit 129-080-901
M22 Series Seal Kit 129-130-901
M22 Series Repair Kit 129-130-902
Kit Part Number
Gun Seal & Repair Kits
20-25 Pump
20-50 Pump
17A Pump
146-260-990
146-270-991
144-919-904
0.25 Quart Plastic Cup (Optional) 139-280-200
Not Available**
144-941-495
144-850-191
144-950-098
Fluid Section Repair Kit
144-950-096
144-960-096
144-919-912
Not Available*
144-850-150
144-850-150
146-260-996
Air Motor Repair Kit
146-260-995
146-270-995
144-919-914
144-931-095
144-941-490
144-850-190
144-950-097
Fluid Section Seal Kit
144-950-091
144-960-091
144-919-905
* PMP-150 Distribution Seal Kit Part Number is 144-931-094** PMP-150 Diaphragm Kit Part Number is 144-931-090
A
B
C
D
E
A
B
AC
CE
SS
OR
IES
15
Airmix® Gun Accessories
A
B
Part Number
For tip sizes 03, 04 and 06 129-609-901
For tip sizes 09 and above 129-529-903
Description
A
B
Part
Tip Seals (Pack of 10)
Standard Airmix® TipsTo order a standard Airmix tip, replace the crosses in 134-5xx-xx4 with the corresponding number read from the table below
(for example, order 134-506-094 for a 06-09 tip). Special 02, 45, 64 and 100 Tips Available Upon Request.
Tip
Siz
e
oz./m
in.
cm3 ./
min
.
oz./m
in.
cm3 ./
min
.
Dia
.Inc
hes
Dia
.mm
Mes
h
Filt
er #
Mes
h
Filt
er #
300 psi20 bar
600 psi41 bar
Gun Filter Pump Filter Maximum Pattern Width at 10”
Narrow Parts Wide PartsMid Range
3.5” 5” 7” 9” 10” 12” 13” 15” 18”
9 cm 13 cm 18 cm 23 cm 25 cm 30 cm 33 cm 38 cm 46 cm
03-03 03-05 03-07
04-03 04-05 04-07 04-09 04-11 04-13
06-03 06-05 06-07 06-09 06-11 06-13 06-15
09-03 09-05 09-07 09-09 09-11 09-13 09-15
12-07 12-09 12-11 12-13 12-15 12-17
14-03 14-05 14-07 14-09 14-11 14-13 14-15 14-17
18-13 18-15 18-17
20-07 20-09 20-11 20-13 20-15 20-17 20-19
25-13
30-07 30-11 30-13 30-15 30-17 30-19
03 2.6 77 4.1 121 .007 0.18 140 4 270 2
04 3.4 101 5.4 160 .009 0.23 140 4 270 2
06 5.1 151 8.1 240 .011 0.28 140 4 140 4
09 7.7 228 12.1 358 .013 0.33 80 6 80 6
12 10.3 305 16.2 479 .015 0.38 50 12 70 8
14 12 355 18.9 559 .016 0.41 50 12 70 8
18 15.3 452 24.2 716 .018 0.46 50 12 50 12
20 17 503 27 798 .019 0.48 50 12 50 12
25 20 591 30 887 .022 0.56 50 12 30 20
30 25.5 754 40.5 1198 .024 0.61 50 12 30 20
VX14 K HVLP VX114Aircaps for Airmix®
Spray Guns
Fits MVX 132-670-920 132-670-940
Quality of spray Excellent Excellent
Adjustable fan Yes No
Transfer efficiency Very good Very good
Non-stick coating No No
Part A for tip sizes 03,04 and 06 are 140 mesh
MVX Gun
Delrin (Pack of 10) 129-679-904
Description
Stainless Steel (Pack of 2) 129-679-905
Carbide (Pack of 2) 129-679-906
Seals (Pack of 10) 129-629-922
Airmix® Gun Seat InsertsMXLT Gun
129-609-911
129-629-923
129-659-904
129-629-922
* Delrin is recommended for most non-pigmented wood coatings.** Stainless steel and carbide are recommended for more abrasive wood
coatings
Xtra™ Series Airmix® Tips - For use with water-based, high solids & polyurethane coatingsTo order a Xtra™ Airmix tip, replace the crosses in 134-5xx-xx2 with the corresponding number read from the table below (for
example, order 134-506-092 for a 06-09 tip). NOTE: Only tip numbers shown in yellow boxes are available as Xtra™ tips.
Part Number
VX14 K HVLP aircap w/ 2 gauges 668-668-587
VX114 K HVLP aircap w/ 1 gauge 668-670-940
Model
HVLP Compliance Test Aircaps w/ gauges
Accessories
Airmix® Gun Accessories Continued
Heating your coating is an often forgotten secret to consistent quality and lower coatingcosts. Without heat the viscosity changes with the temperature, resulting in inconsistent finishquality and lower efficiency as you raise the atomization pressure to break up thicker paint.By adding a circulation kit and heater, set at 90°F (25°C), you deliver the same quality allyear round.
Do not exceed 90°F (25°C) with polyurethanes and acid curecoatings since a higher temperature shortens their pot life.
Part Number
110V 056-146-050
220V 056-146-000
Explosion Proof
Explosion Proof
Voltage ConstructionPart Number
Aluminum Circulation Valve 668-314-010
For 20.25, 20.50 & 17A Pumps
Circulation Kits and Heaters
Circulating Kits Stainless Steel Paint Heaters
Part Number
MVX Seal Kit (Pack of 3) 129-679-901
Description
MVX Repair Kit 129-679-902
MXLT Seal Kit (Pack of 3) 129-659-901
MXLT Air Valve Kit 129-659-902
Airmix® Gun Seal and Repair Kit
Each Kit Contains:1. 3ft Whip Hose2. 10ft Fluid Hose for Heater3. 25ft Fluid Hose4. Y-Fitting (Non-Stainless)5. Circulation Valve or Back Pressure Regulator
(See Photo)
Part Number
2-3-4-6 129-609-907
Tip NumberScreen Number Mesh (Microns)
140 (99µ)
9 129-609-90885 (168µ)
12+up
4
6
12 129-609-90960 (280µ)
Gun Filter - Pack of 5
Part Number
For 03 to 09 tips 000-094-000
Description
For 12 to 100 tips 000-094-002
Unclogging Needle Holder 669-094-000
Unclogging Needles - Pack of 12
AC
CE
SS
OR
IES
17
Part Number
Hose Sleeve - 16’ 669-990-101
Hose Sleeve - 25’ 669-990-102
Hose Sleeve - 32’ 669-990-103
Hose Sleeve - 50’ 669-990-106
Hose Sleeve - 100’ 669-990-104
Hose Sleeve - 1000’ 669-990-105
Description
Hose Protection Sleeve
Length 50’
HVLP & LP Fluid Hose
Flui
dA
ir
668-362-150
Airmix® Fluid Hose 050-450-607
Stainless Airmix® Fluid Hose 668-455-850
Airmix® and LP - Air Hose 050-382-216
HVLP Air Hose
750 psi
3000 psi
3000 psi
150 psi
150 psi 668-395-150
Description Length 25’
668-362-125
050-450-605
050-450-653
050-382-214
050-389-103
Length 16’
668-362-116
050-450-604
050-450-652
050-382-209
050-389-101
Maximum Pressure
1/4”
3/16”
3/16”
1/4”
5/16”
Hose Inside Diameter
F 3/8” NPS
F #5 JIC
F #5 JIC
F 1/4” NPS
F 1/4” NPS
Fittings
Hoses
General Accessories
Part Number
Two Gun Manifold for All Airmix® Pumps except EZMix & 10-14 669-669-017
Description
Stainless Steel Two Gun Manifold
Part Number
10-14A
B
155-580-510
ModelsParts Construction
Stainless Steel
10-25, 20-25, 20-50and 17A 055-580-100Stainless Steel
Inlet
1/4 NPT (M)
1/4 NPT (F)
Outlet
#5 J.I.C. (M)
#5 J.I.C. (M)
Pressure Rating
900 psi
3500 psi
Superfilters - Come with #6 filter screen
03/04
Tip Size
2
4
6
8
n° Part Number
000-161-102200
Screen Size (Mesh)
06 000-161-104
09 000-161-106
12/14
140
85
70 000-161-108
1220 60 000-161-112
Superfilter Screen
A
Two GunManifold
B
AFNOR 4 (CA4) Centipoises Ford 4 (CF4) DIN 4 (D°) ZAHN (n°2) ZAHN 312 20 10 11 18
14 25 12 12 19
16 30 14 14 20
20 40 18 16 22
25 50 22 20 24
29 60 25 23 27
32 70 28 25 30
34 80 30 26 34
37 90 33 28 37 10
40 100 35 30 41 12
45 120 40 34 49 14
50 140 44 38 58 16
56 160 50 42 66 18
61 180 54 45 74 20
66 200 58 49 82 23
Accessories
General Accessories Continued
Plastic cup for calculating the viscosity of a liquid.The time it takes the liquid to pass through the cupin seconds corresponds to the AFNOR4 scale.
Viscosity Cup - AFNOR4Viscosity Cup Conversion Chart
Part Number
Viscosity cup n°4 CA4 049-221-400
Description
Instrument for reading the thickness of a wet film.
All covers are stainless steel
Wet Film Thickness Gauge
Part Number
Thickness Gauge 999-400-025
Description
Part Number
5 Gallon Agitator and Cover (Nylon Blade) 668-668-806
55 Gallon Agitator and Cover (Nylon Blades) 668-668-320
Part
A
B
Description
Agitators for 5 Gallon Pail and 55 Gallon Drum
B
A
55 Gallon Agitator and Elevator 668-900-125
M3R-55E Gear reduced Agitator and Elevator 668-999-610
C
C
AC
CE
SS
OR
IES
19
Great for spraying sealers and topcoats with one pump.Larger Manifolds (4 or More Suction Rods) Available upon Request
Suction Manifolds
Part Number
2-Way Suction Manifold w/o Suction RodsA
B
669-669-024
2-Way Suction Manifold w/o Suction Rods 669-669-026
Description Pump
10-14, PMP-150
20-25, 20-50 and 17A
3-Way Suction Manifold w/o Suction Rods 669-669-025
3-Way Suction Manifold w/o Suction Rods
For stainless steel or other sizes call a Kremlin representative.
669-669-027
S/S Number
668-668-449
N/A
668-668-450
N/A
10-14, PMP-150
20-25, 20-50 and 17A
Parts
CartsPart Number
One Arm Cart (A) 051-730-110
Two Arm Cart with wall plate (required for cart mounted heated systems) 668-221-000
Description Pump
Fits 10.14 & PMP pumps
Fits all listed pumps
Stainless Steel Suction AssembliesPart Number
5 Gallon 049-596-010
5 Gallon 049-596-110
Description Pump
PMP-150, 02-75 and 10-14
20-25, 20-50 and 17A
55 Gallon 668-668-201PMP-150, 02-75 and 10-14
55 Gallon 668-595-10020-25, 20-50 and 17A
Protects the paint guns and pumps from wearing prematurely.Lubricants P & T are used in the lubricating cup located on thepump fluid section.
Gun & Pump Lubricants
Part Number
.33 oz. Tube of Techni Lub 560-440-101
Can of Techni Lub (15.5 oz.) 560-440-001
Lubricant T - for solvent based paints (1 Gallon/3.78 liters) 668-990-001
Lubricant P - for Polyurethanes (1 Gallon/3.78 liters) 668-990-021
Description
Thick white paste for the hands and face. It guarantees full protection for
half a day and is easily removed by rinsing. Free from silicone and
colorings.
Protective Cream
Part Number
Protective Cream - pack of 36 Tubes 143-039-912
Protective Cream - pack of 6 Tubes 143-039-913
Protective Cream - 1 Tube 043-039-912
Description
B
A
Item
A
B
C
D
A
B
C
Four Wheel Cart with 5 gallon pail support (B) 668-668-599Fits all listed pumps
B A
Special Applications
Manual Airspray Guns, Pumps & Systems
Kremlin offers a complete line of airspray equipment to service all
industries. From a standard conventional siphon feed gun to a complete
multi-gun system, Kremlin has what you need. For more information please
refer to the Manual Airspray Catalog.
Automatic Guns for Flatline Systems
Kremlin’s AVX automatic Airmix® and A25HTI Automatic HVLP guns provide the premium finish required by users of
flatline systems. Kremlin guns are designed with detachable base assemblies to make cleaning and maintenance easy.
For more information, please refer to the Automatic Spray Catalog.
A25 HTI Gun AVX Gun
Mechanical & Electronic Plural Component Systems
For the best in plural component systems, look to Kremlin. The PU2120 and
PU2200 mechanical systems provide a simple solution to accurate mixing, while
the Cyclomix™, Cyclomix™ Multi and Cyclomat™ offer very precise electronic
control of the mixing process for standard and acid catalyzed coatings. For more
information, please refer to the Plural Component Systems Catalog.
Cyclomat™
Cyclomix™
PU2120
PU2200
Cyclomix™ Multi
Fluid Delivery Equipment - For Very High Volume Shops
Kremlin has a wide variety of large pumps for very high volume wood finishing shops that require special
fluid delivery and control equipment. Please refer to the Fluid Delivery Catalog for more information.
K-Series Double Diaphragm Pumps
Color Changers
Piston Pumps
Extrusion Systems for Adhesives & Sealants
Kremlin Rexson makes a complete line of single and plural component extrusion equipment and
accessories. These systems can easily extrude caulkings, adhesives and sealants from 5 or 55 gallon
drums through manual or automatic extrusion guns. For more information, please refer to the 1K Extrusion
Equipment Selection Guide.
Automatic Extrusion Valves
Single Post Ram Extrusion Pump
Manual Extrusion Valves
21
July, 2008Revision #4Catalog # LT 999-200-015
Your Solution & Service Center is:
EXEL North America, IncCanadian Branch931 Progress Ave., Unit 7Scarborough, Ontario M1G 3V5Toll Free: (800) 450-0655Phone: (416) 431-5017Fax: (416) 431-9171
EXEL North America, Inc.North American Headquarters45001 5 Mile RoadPlymouth, MI 48170Toll Free: (800) 573-5554Phone: (734) 979-0100Fax: (734) 927-0064
EXEL-NA, S.A. DE C.V.Mexico BranchMoisés Sáenz 1510, Col. LeonesMonterrey, N. L. México, CP 64600Phone: (81) 1257-1111Fax: (81) 1352-8316