Manual de utilizare pentru
Tastatura LCD si Tastatura LCD pentru acces controlDGP2-641 and DGP2-641AC
Ledul AC:ON = tensiune prezentaOFF = lipsa tensiune alimentare
Ledul STATUS :
Verde:ON = toate zonele sunt inchiseOFF = Zona(e) deschiseFlash = Timp de intarziere
Rosu:ON = Sistem(e) armateOFF = Sistem(e) dezarmateFlash = Alarma
LCD Keypad and Access Control LCD KeypadDGP2-641 and DGP2-641AC
Ecranul LCD va va ghida cu mesaje explicite
Foloseste sagetile pentru navigare si selectie
[CLEAR] = Sterge data curenta sau revine la pasul anterior
[ENTER] = Salveaza data curenta si iese din pasul curent
Armare regulata
Armarea regulat armeaza toate zonele din aria selectata(e)
1. Tasteaza [CUDUL DE ACCES].
3. Daca aveti acces la mai multe arii selectti aria dorita sau apasati [0] petru toate ariile.In cazul cand sunt mai multe arii programate
2. Apasa butonul [ARM].Armeaza aria daca toate zonele sunt inchise.
Armarea fortata- “Force Arming”Armarea fortata permite armare sistemului cu zone deschise. Zonele se programeaza in prealabil
1. Tasteaza [CODUL DE ACCES].
3. Daca aveti acces la mai multe arii, selecteaza aria dorita , sau apasti tasta [0] pentru toate ariile.
2. Tasteaza butonul [FORCE] .Armeaza intreaga arie fara a mai astepta sa se inchida zonele declarate force.
Armarea partiala –”Stay Arming”
“Stay arming” va arma partial sistemul, - doar zonele nedeclarate “stay” (progrmarea se face in prealabil de programator la cerere)
1. Tastati [CODUL DE ACCES].
3. Daca aveti acces la mai multe arii, selecteaza aria dorita, sau apasa tasta [0] pentru toate ariile.
2. Tastati butonul [STAY] .Armeaza doar zonele nedeclarate “stay”,
Armarea Instant
Cu armarea instant,toate zonele vor genera alarma imediat ce se armeaza sistemul(chiar si zonele definite intarziat)
1. Tastati [CODUL DE ACCES].
3. Daca aveti acces la mai multe arii, alegeti aria dorita, sau apasati [0] pentru toate ariile.
2. Tastati butonul [5].Arie armata “stay”, dar alarma se va declansa daca sunt zone deschise (chiar daca sunt definite intarziat)
2. Select the desired area(s).
To disarm when entering:
3. Select the desired area(s).
Disarming
1. Enter your [ACCES CODE].
To disarm from within the perimeter:
1. Enter your [ACCES CODE].
2. Press the [DISARM] button.
5. Repeat steps 3 and 4 until all desired zones selected.
4. Press the [BYP] button once the desired zone appears on the screen.
Bypass Programming
1. Enter your [ACCES CODE].
2. Press the [BYP] button.
3. Use the [] and [] buttons to scroll through the zones.
6. Press [ENTER] to save and exit.
When a zone is bypassed, it will be ignored the next time your system is armed.
4. Introdu numarul zonei(din 2 digiti).
3. Tasteaza butonul [1] pentru a seta zona(ele) chime .
Programare “Chime”
1. Tasteaza [CODUL DE ACCES].
5. Tasteaza butonul [ENTER] pentru a salva.
2. Tasteza butonul [9] .
Tastatura poate fi programatasa emita un sunet(beep) rapid si intermitent de fiecare data cand zona programta este deschisa.
SAUFoloseste butoanele[] si []pentru a selecta zona(ele) si apasa butonul [ACC] pentru a activa sau dezactiva functia “chime”.
6. Tasteaza [CLEAR] pentru a iesi.
4. Enter a start time according to the 24hr clock (9:00 p.m. = 21:00).
5. Enter an end time according to the 24hr click (9:00 p.m. = 21:00).
Programming a Chime Zone Schedule
3. Press the [2] button to set a chime schedule.
Chime zones can also be programmed to chime only when opened between certain hours.
6. Press [CLEAR] to exit.
1. Enter your [ACCES CODE].
2. Press the [9] button.
Alarm Memory Display
“Alarms in Memory [MEM] to View” will appear when an alarm has occurred.
2. Press [CLEAR] to exit.
1. Press the [MEM] button to view the breached zones.
Press and hold the desired one-touch button to access the following:
Button Feature
Table 1: One-touch Buttons
One-Touch Buttons
[BYP] Bypass programming
[ENTER] Regular arm
[5] Instant arm
[6] Keypad settings
[7] View event record display
[STAY] Stay arm
[FORCE] Force arm
[DISARM] Disarm a Stay/InstantArmed area
Panic Buttons
Press and hold one of the button combinations listed below to send a panic alarm.
Panic Alarm Type ButtonCombinations
Table 2: Panic Buttons
Fire Alarm [7] and [9]
Auxiliary Panic (medical) [4] and [6]
Emergency Panic (police) [1] and [3]
Programming User Access Codes – Steps 1 to 6
4. Enter the 3-digit User Number to program.
5. Enter a user code (PIN)
1. Enter your [ACCES CODE].
6. Press the [] button.
3. Press [ACC].
2. Press [0].
Press [] to scroll the user codes and then press [ACC].
OR
9. Enter the number of the area you wish to assign.
Programming User Access Codes – Steps 7 to 9
8. Press the [] button.
7. Press the number(s) of the user option(s) you wish to enable/disable.
Programming User Access Codes – Steps 10 and 11
11. Enter 2-digit schedule.
10. Enter 2-digit access level.
Press the [] button to return to user options; press the [] button to proceed to step 10; press the [ENTER] button to save and exit.
Programming User Access Codes – Steps 12 to 15
14. Enter the access control card’s serial number by either using the keypad’s buttons or by presenting the card to the keypad’s reader.
15. Press [ENTER] to save and exit.
13. Press the [] button.
12. Press the number(s) of the access control option(s) you wish to enable/disable.
Trouble Display
“Trouble(s) [TRBL] to View” will appear when a trouble occurs. To view the trouble display:
Use the [] and [] buttons.
Press the [TRBL] button.
Press the [NUMBER] of the trouble.
Group [1]: System
AC Failure
Battery Trouble
AUX Current Limit
Bell Current Limit
Bell Absent
ROM Check Error
RAM Check Error (DGP-NE96)
Trouble Display – Group [1]: System
Group [2]: Communicator
TLM1
Fail to Communicate 1
Fail to Communicate 2
Fail to Communicate 3
Fail to Communicate 4
Fail to Communicate PC
Trouble Display - Group [2]: Communicator
Group [3]: Modules
Module Tamper
ROM Check Error
TLM Trouble
Fail to Communicate
Printer Trouble
AC Failure
Battery Failure
Supply Output
Trouble Display - Group [3]: Modules
Group [4]: Bus
Missing Keypad
Missing Module
General Failure
Bus Overload
Bus Comm. Error
Group [5]: Zone Tamper
Group [6]: Zone Low Battery
Group [7]: Zone Fault
Group [8]: Clock Loss
Trouble Display - Groups [4] to [8]
Thank You