en iso

8/12/2019 EN ISO

1/11

CEN on julkaissut seuraavat toimialueellemme kuuluvat EN- ja EN ISO -standardit ja muut julkaisut.Julkaisut luetellaan CEN/ECISS-komiteakohtaisesti. Luettelossa mahdollisesti mainittava suomenkielinen

otsikko on alustava ja voi muuttua vastaavan SFS-julkaisun vahvistamisen tai julkaisemisen yhteydess.

EN- ja EN-ISO -standardit sek niihin tehtvt muutokset (tunnuksen lopussa oleva "/A1"," /A2", jne.

osoittaa jo aikaisemmin julkaistuun standardiin tehtv muutosta)" vahvistetaan normaalisti 6

kuukauden kuluessa SFS-standardeiksi. Teknisi raportteja ("CEN/TR", "CEN ISO/TR tai "CR"), teknisi

spesifikaatioita ("CEN/TS") sek jo julkaistuihin standardeihin tehtyj korjauksia (tunnuksen lopussa

oleva "/AC", "/AC1" jne.) ei erikseen vahvisteta.

Osa lueteltavista julkaisuista tullaan myhemmin julkaisemaan suomenkielisin SFS-julkaisuina

(listietoa asiantuntijoiltamme).

Listietoja uusimmista CEN-julkaisuista (kaikki toimialat) on SFS:n verkkosivuilla osoitteessa:

http://www.sfs.fi/julkaisut/cen_julkaisut/

Tulostettu (Generated) 17.12.2008

Uudet EN- ja EN ISO-standardit (1.10.2008... 31.10.2008)

Metalliteollisuuden Standardisointiyhdistys ry - http://www.metsta.fi/standardit

8/12/2019 EN ISO

2/11

Tulostettu 2008-12-17 1 (11)

Uudet EN- ja EN ISO -standardit ja muut CENin julkaisut

SFS-julkaisuja myy Suomen Standardisoimisliitto SFS ry.

Luettelo sislt CEN-julkaisut, joiden ilmestymispiv on 2008-10-01 ... 2008-10-29

CEN/SS T01 Shipbuilding and maritime structures

EN ISO 14509-1:2008Veneet. Moottoriveneiden aiheuttama ilmani. Osa 1: Mittaukset ohi ajettaessa

Small craft. Airborne sound emitted by powered recreational craft. Part 1: Pass-by measurement procedures (ISO

14509-1:2008)

CENin julkaisupiv 2008-10-01Asiantunti ja: Arto Ki vir int a

CEN/TC 10 Lifts, escalators and moving walks

EN 81-40:2008Hissien suunnittelua ja rakentamista koskevat turvallisuusohjeet. Erityistarkoituksiin kytettvt henkil- ja

tavarahenkilhissit. Osa 40: Porrashissit ja vinolla radalla liikkuvat nostolavat liikuntaesteisille henkilille

Safety rules for the construction and installation of lifts. Special lifts for the transport of persons and goods. Part 40:

Stairlifts and inclined lifting platforms intended for persons with impaired mobility

CENin julkaisupiv 2008-10-29

Asiantunti ja: Arto Ki vir int a

CEN/TC 121 Welding

EN ISO 14113:2008

Kaasuhitsausvarusteet. Letkukiinnitykset kumi- ja muoviletkuille tiivistetyille tai nesteytetyille kaasuille

enimmissuunnittelupaineelle 450 bar

Gas welding equipment. Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45

MPa) (ISO 14113:2007)


EN ISO 3834-5:2005/AC:2008

Metallien sulahitsauksen laatuvaatimukset. Osa 5: Tarvittavat asiakirjat standardien ISO 3834-2, ISO 3834-3 ja ISO

3834-4 mukaisten vaatimusten osoittamiseksi

Quality requirements for fusion welding of metallic materials. Part 5: Documents with which it is necessary to conform to

claim conformity to the quality requirements of ISO 3834-2, ISO 3834-3 or ISO 3834-4 (ISO 3834-5:2005/Cor 1:2007)


EN ISO 14172:2008Hitsausaineet. Hitsauspuikot nikkelin ja nikkeliseosten puikkohitsaukseen. Luokittelu

Welding consumables. Covered electrodes for manual metal arc welding of nickel and nickel alloys. Classification (ISO

14172:2008)


Asiantunt ija: Carl-Gustaf Lindewald

CEN/TC 122 Ergonomics

8/12/2019 EN ISO

3/11

EN 894-1:1997+A1:2008

Safety of machinery. Ergonomics requirements for the design of displays and control actuators. Part 1: General principles

for human interactions with displays and control actuators


EN 894-2:1997+A1:2008

Safety of machinery. Ergonomics requirements for the design of displays and control actuators. Part 2: Displays


EN 894-3:2000+A1:2008

Safety of machinery. Ergonomics requirements for the design of displays and control actuators. Part 3: Control actuators


EN 1005-1:2001+A1:2008

Safety of machinery. Human physical performance. Part 1: Terms and definitions


EN 1005-2:2003+A1:2008

Safety of machinery. Human physical performance. Part 2: Manual handling of machinery and component parts of

machinery


EN 1005-3:2002+A1:2008

Safety of machinery. Human physical performance. Part 3: Recommended force limits for machinery operation


EN 1005-4:2005+A1:2008

Safety of machinery. Human physical performance. Part 4: Evaluation of working postures and movements in relation to

machinery


Asiantunti ja: Aarre Viljanen

CEN/TC 130 Space heating appliances without integral heat sources

EN 1264-2:2008

Water based surface embedded heating and cooling systems. Part 2: Floor heating: Prove methods for the determination of

the thermal output using calculation and test methods


EN 1264-5:2008

Water based surface embedded heating and cooling systems. Part 5: Heating and cooling surfaces embedded in floors,

ceilings and walls. Determination of the thermal output


Asiantunti ja: Jor ma Rail io

8/12/2019 EN ISO

4/11

CEN/TC 132 Aluminium and aluminium alloys

EN 485-2:2008Alumiini ja alumiiniseokset. Levyt ja nauhat. Osa 2: Mekaaniset ominaisuudet

Aluminium and aluminium alloys. Sheet, strip and plate. Part 2: Mechanical properties


EN 13957:2008Alumiini ja alumiiniseokset. Pursotetut kiepill olevat pyret putket yleiseen kyttn. Spesifikaatiot

Aluminium and aluminium alloys. Extruded round, coiled tube for general applications. SpecificationCENin julkaisupiv 2008-10-15

EN 13958:2008Alumiini ja alumiiniseokset. Vedetyt kiepill olevat pyret putket yleiseen kyttn. Spesifikaatiot

Aluminium and aluminium alloys. Cold drawn, round, coiled tube for general applications. Specification


Asiantunti ja: Mika Vart iainen

CEN/TC 142 Woodworking machines - Safety

EN 861:2007/AC:2008Puuntystkoneiden turvallisuus. Yhdistetyt oiko- ja tasohylkoneet

Safety of woodworking machines. Surface planing and thicknessing machines



CEN/TC 143 Machine tools - Safety

EN 13218:2002+A1:2008/AC:2008

Machine tools. Safety. Stationary grinding machinesCENin julkaisupiv 2008-10-22


CEN/TC 145 Plastics and rubber machines

EN 1114-3:2001+A1:2008

Plastics and rubber machines. Extruders and extrusion lines. Part 3: Safety requirements for haul-offs


EN 12409:2008Kumi- ja muoviteollisuuden koneet. Lmpmuovauskoneet. Turvallisuusvaatimukset

Plastics and rubber machines. Thermoforming machines. Safety requirements


EN 13418:2004+A1:2008

Plastics and rubber machines. Winding machines for film or sheet. Safety requirements



8/12/2019 EN ISO

5/11

CEN/TC 147 Cranes - Safety

EN 13157:2004/AC:2008

Cranes. Safety. Hand powered lifting equipment


Asiantunti ja: Jukka-Pekka Rapinoja

CEN/TC 149 Power-operated warehouse equipment

EN 528:2008Hyllysthissit. Turvallisuus

Rail dependent storage and retrieval equipment. Safety requirements



CEN/TC 151 Construction equipment and building material machines - Safety

EN 474-2:2006+A1:2008

Earth-moving machinery. Safety. Part 2: Requirements for tractor-dozers


EN 474-11:2006+A1:2008

Earth-moving machinery. Safety. Part 11: Requirements for earth and landfill compactors


EN 474-12:2006+A1:2008

Earth-moving machinery. Safety. Part 12: Requirements for cable excavators


EN 500-2:2006+A1:2008

Mobile road construction machinery. Safety. Part 2: Specific requirements for road-milling machines


EN 500-3:2006+A1:2008

Mobile road construction machinery. Safety. Part 3: Specific requirements for soil-stabilising machines and recyclingmachines


EN 500-6:2006+A1:2008

Mobile road construction machinery. Safety. Part 6: Specific requirements for paver-finishers


EN 12336:2005+A1:2008

Tunnelling machines. Shield machines, thrust boring machines, auger boring machines, lining erection equipment. Safety

8/12/2019 EN ISO

6/11

requirements


EN 13367:2005+A1:2008

Ceramic machines. Safety. Transfer platforms and cars


EN 13531:2001+A1:2008

Earth-moving machinery. Tip-over protection structure (TOPS) for compact excavators. Laboratory tests and performancerequirements (ISO 12117:1997 modified)



CEN/TC 156 Ventilation for bui ldings

EN ISO 5801:2008

Industrial fans. Performance testing using standardized airways (ISO 5801:2007 including Cor 1:2008)


EN ISO 5802:2008

Industrial fans. Performance testing in situ (ISO 5802:2001)


EN ISO 12499:2008

Industrial fans. Mechanical safety of fans. Guarding (ISO 12499:1999)


EN ISO 13349:2008

Industrial fans. Vocabulary and definitions of categories (ISO 13349:1999)


EN ISO 13350:2008

Industrial fans. Performance testing of jet fans (ISO 13350:1999)


EN ISO 13351:2008

Industrial fans. Dimensions (ISO 13351:1996)CENin julkaisupiv 2008-10-22


CEN/TC 165 Waste water engineering

EN 1124-3:2008

Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems. Part 3:

System X. Dimensions

8/12/2019 EN ISO

7/11

8/12/2019 EN ISO

8/11


CEN/TC 188 Conveyor belts

EN 12882:2008Yleiskyttn tarkoitetut kuljetushihnat. Shk- ja paloturvallisuusvaatimukset

Conveyor belts for general purpose use. Electrical and flammability safety requirements



CEN/TC 197 Pumps

EN 13951:2003+A1:2008

Liquid pumps. Safety requirements. Agrifoodstuffs equipment. Design rules to ensure hygiene in use


EN 14343:2005/AC:2008

Rotary positive displacement pumps. Performance tests for acceptanceCENin julkaisupiv 2008-10-22


CEN/TC 214 Textile machinery and accessories

EN ISO 8230-1:2008Kuivapesukoneiden turvallisuusvaatimukset. Osa 1: Yleiset turvallisuusvaatimukset

Safety requirements for dry-cleaning machines. Part 1: Common safety requirements (ISO 8230-1:2008)


EN ISO 8230-2:2008Kuivapesukoneiden turvallisuusvaatimukset. Osa 2: Perkloorietyleeni kyttvt koneet

Safety requirements for dry-cleaning machines. Part 2: Machines using perchloroethylene (ISO 8230-2:2008)


EN ISO 8230-3:2008

Kuivapesukoneiden turvallisuusvaatimukset. Osa 3: Helposti syttyvi liuottimia kyttvt koneet

Safety requirements for dry-cleaning machines. Part 3: Machines using combustible solvents (ISO 8230-3:2008)


EN ISO 10472-1:2008Teollisuuspesukoneiden turvallisuusvaatimukset. Osa 1: Yleiset vaatimukset

Safety requirements for industrial laundry machinery. Part 1: Common requirements (ISO 10472-1:1997)


EN ISO 10472-2:2008Teollisuuspesukoneiden turvallisuusvaatimukset. Osa 2: Pesukoneet ja lingot

Safety requirements for industrial laundry machinery. Part 2: Washing machines and washer-extractors (ISO 10472-2:1997)


EN ISO 10472-3:2008Teollisuuspesukoneiden turvallisuusvaatimukset. Osa 3: Pesulinjat ja niiden koneet

8/12/2019 EN ISO

9/11

Safety requirements for industrial laundry machinery. Part 3: Washing tunnel lines including component machines (ISO

10472-3:1997)


EN ISO 10472-4:2008Teollisuuspesukoneiden turvallisuusvaatimukset. Osa 4: Kuivauskoneet

Safety requirements for industrial laundry machinery. Part 4: Air dryers (ISO 10472-4:1997)



CEN/TC 231 Mechanical vibration and shock

EN ISO 8041:2005/AC:2008

Human response to vibration. Measuring instrumentation (ISO 8041:2005/Cor 1:2007)



CEN/TC 262 Metallic and other inorganic coatings

EN 12487:2007/AC:2008

Corrosion protection of metals. Rinsed and non-rinsed chromate conversion coatings on aluminium and aluminium alloys



CEN/TC 290 Dimensional and geometrical product specification and

verification

EN ISO 4287:1998/AC:2008

Geometrical product specifications (GPS). Surface texture: Profile method. Terms, definitions and surface texture

parameters (ISO 4287:1997/Cor 1:1998/Cor 2:2005)


EN ISO 5436-2:2001/AC:2008

Geometrical Product Specifications (GPS). Surface texture: Profile method; Measurement standards. Part 2: Software

measurement standards (ISO 5436-2:2001/Cor 1:2006/Cor 2:2008)


EN ISO 11562:1997/AC:2008

Geometrical product specifications (GPS). Surface texture: Profile method. Metrological characteristics of phase correct

filters (ISO 11562:1996/Cor 1:1998)


EN ISO 12085:1997/AC:2008

Geometrical product specification (GPS). Surface texture: Profile method. Motif parameters (ISO 12085:1996/Cor 1:1998)


8/12/2019 EN ISO

10/11

EN ISO 12179:2000/AC:2008

Geometrical Product Specifications (GPS). Surface texture: Profile method. Calibration of contact (stylus) instruments (ISO

12179:2000/Cor 1:2003)



CEN/TC 294 Communication systems for meters and remote reading of

meters

EN 1434-3:2008

Heat Meters. Part 3: Data exchange and interfaces


EN 13757-5:2008

Communication systems for meters and remote reading of meters. Part 5: Wireless relaying


EN 13757-6:2008

Communication systems for meters and remote reading of meters. Part 6: Local Bus



CEN/TC 322 Equipments for making and shaping of metals - Safety

requirements

EN 15093:2008Koneturvallisuus. Levytuotteiden kuumavalssaimien turvallisuusvaatimukset

Safety of Machinery. Safety requirements for hot flat rolling millsCENin julkaisupiv 2008-10-01

EN 15094:2008

Koneturvallisuus. Levytuotteiden kylmvalssaimien turvallisuusvaatimukset

Safety of Machinery. Safety requirements for cold flat rolling mills



CEN/TC 344 Steel static storage systems

EN 15620:2008Kiintet terksiset hyllystjrjestelmt. Sdettvt palettihyllystt. Toleranssit, muodonmuutokset ja vapaat vlit

Steel static storage systems. Adjustable pallet racking. Tolerances, deformations and clearances



CEN/TC 54 Unfi red pressure vessels

EN 13445-5:2002/A10:2008

8/12/2019 EN ISO

11/11

Lmmittmttmt painesilit. Osa 5: Tarkastus ja testaus A10: Kohta 10.2.3.3 Normaali nestepainekoe

Unfired pressure vessels. Part 5: Inspection and testing


Asiantunt ija: Carl-Gustaf Lindewald

ECISS/TC 1 Steel - Mechanical testing

EN ISO 12004-1:2008

Metallilevyjen ja -nauhojen rajamuovattavuuskyrien mrittminen. Osa 1: Mittaukset ja rajamuovattavuuspiirrosten

soveltaminen konepajassa

Metallic materials. Sheet and strip. Determination of forming-limit curves. Part 1: Measurement and application of

forming-limit diagrams in the press shop (ISO 12004-1:2008)


EN ISO 12004-2:2008

Metallilevyjen ja -nauhojen rajamuovattavuuskyrien mrittminen. Osa 2: Rajamuovattavuuskyrien mrittminen

laboratoriossa

Metallic materials. Sheet and strip. Determination of forming-limit curves. Part 2: Determination of forming-limit curves in the

laboratory (ISO 12004-2:2008)



ECISS/TC 22 Steels for pressure purposes - Qualities

EN 10269:1999/A1:2006/AC:2008

Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties



ECISS/TC 23 Steels for heat treatment, alloy steels and free-cutting steels -Qualities and dimensions

EN 10083-3:2006/AC:2008

Steels for quenching and tempering. Part 3: Technical delivery conditions for alloy steels



ECISS/TC 30 Steel wires

EN 10324:2004/AC:2008

Steel wire and wire products. Hose reinforcement wire

