energy efficiency documentation - telecom …...tb-m15 rev.a test report for code of conduct on...

Informazione al cliente – Information to customer

Wireless range extender WRE6505

Manufactured by Zyxel

Dichiarazione Ambientale – Environmental declaration

Documentazione di supporto – backup support

ENERGY EFFICIENCY DOCUMENTATION

CREATIVE SAFETY & CONSULTANT CO.

Report No: C0420L13-D1

非經本公司書面許可，不得透露或使用本資料亦不准複印複製或轉變成任何其他形式使用 Shall not be distributed, copied, reproduced, or disclosed in whole or in part without prior written approval of Creative Safety & Consultant Corporation.

TB-M15 Rev.A

TEST REPORT for

Code of Conduct on Energy Consumption of Broadband Equipment

Version 5.0

Report reference ........................... : C0420L13-D1

Date of issue ................................. : 2015-09-22

Number of pages .......................... : 10 pages

Applicant ....................................... : ZyXEL Communications Corporation

Address ......................................... : No. 2, Gongye E. 9th Road, Hsinchu Science Park, Hsinchu, Taiwan, R.O.C.

Test Object ................................... : Wireless Range Extender

Model name .................................. : WRE6505

Rating ............................................ : I/P: 100-240Vac, 50/60Hz, 0.15A

P/N no. ......................................... : N/A

Trademark .................................... :

Testing laboratory ......................... : Creative Safety & Consultant Co.

Address ......................................... : 13F, No. 190, Sec. 2, Chung Hsing Road, Hsin Tien Dist., New Taipei City, Taiwan

Testing location ............................. : As above

Standard ....................................... : The test report is based on the following requirements：

Code of conduct on energy consumption of broadband

equipment, version 5.0：2013-12-20

IEC 62301:2011 Household electrical appliances - Measurement of standby power

Test procedure .............................. : Complete test acc. to Test Report Format

Partial test acc. to component changed

Test results ................................... : Pass

Reported by .. : Leo Yueh Approved by .. : Ken Wu

( signature) ( signature)




TB-M15 Rev.A

External Power Supply: N/A

Model name .................................. : N/A

Rating ............................................ : N/A

Standby mode ............................... : Provided Not provided

Off mode ....................................... : Provided Not provided

Networked standby ....................... : Provided Not provided

Idle state ........................................ Provided Not provided

On-stat state .................................. Provided Not provided

Information or display function under standby mode ..................... :

Provided Not provided

External power supply .................. : Provided

Not provided

Ambient light sensor ..................... : Provided externally defined illuminance levels:___lx

Reference illuminance levels: >300lx and




TB-M15 Rev.A

General Remarks

"(see remark #) refers to a remark appended to the report.

" (see appended table)” refers to a table appended to the report.

Throughout this report a point is used as the decimal separator.

The test results presented in this report relate only to the object tested.

This report shall not be reproduced except in full without the written approval of applicant.

This report shall not be reproduced except in full without the written approval of ZyXEL

Communication Corporation.

Verdicts

Possible test case verdicts：

-Test case does not apply to the test object ....................... : N/A (not applicable)

-Test object does meet the requirement ............................ : P (Pass)

-Test object does not meet the requirement ...................... : F (Fail)

Test item particulars

Accordance with the code of conduct on energy consumption of broadband equipment, version 5.0. Test items:

No. Home targets for Home

Network Infrastructure Device

Tier 2015 - 2016

Idle-State Standard

(W)

On-State Standard

(W)

1

Wi-Fi Access Points with IEEE 802.11n or 802.11ac radio with up to 20 dBm total EIRP at 2,4 GHz

2.10 3.30

2

Wi-Fi Access Points with IEEE 802.11n or 802.11ac radio with up to 30 dBm total EIRP at 5 GHz

3.60 5.70

3 1 Fast Ethernet port

0.20 0.40




TB-M15 Rev.A

1. General information of product:

Copy of marking plate:

Product description

1. The EUT (Equipment Under Test) is a Wireless Range Extender which has one RJ-45 ports for information technology equipments including electrical business equipment.

Information of product power saving modes

The EUT (Equipment Under Test) has a button to control Off mode and designs IC to control networked standby mode.

Main IC chipset: MEDIATEK MT7620A

Characteristic data:

1. Product dimension : L: 91.2 mm * W: 62.5 mm

2. Product total weight : Approx. 0.11 Kg

Attachments

1. Pictures of product

2. Instrument and equipment

3. Equipment list




TB-M15 Rev.A

2. Test result:

A. Power targets for Home Network Infrastructure Device (HNID) - 230Vac, 50Hz

No. Home targets for Home

Network Infrastructure Device

Tier 2015 - 2016

Idle-StateStandard

(W)

Idle-StateTest Result

(W)

On-State Standard

(W)

On-StateTest Result

(W)

1

Wi-Fi Access Points with IEEE 802.11n or 802.11ac radio with up to 20 dBm total EIRP at 2,4 GHz

2.10 2.03 3.30 2.42

2

Wi-Fi Access Points with IEEE 802.11n or 802.11ac radio with up to 30 dBm total EIRP at 5 GHz

3.60 2.17 5.70 3.11

3 1 Fast Ethernet port

0.20 0.11 0.40 0.15

B. Ambient condition & Power management uncertainty

No.

General conditions for measurements

& Power management uncertainty

Measuring result Verdict

1

Ambient condition met requirement of -Tamb (23±5℃)

-Airspeed ≤ 0.5m/s

T：27.0℃

Airspeed： 0.05m/s

P

2

Power source mets requirement of -Voltage (230±1%) -Frequency (50Hz±1%) -THD value < 2% -Ratio of peak value of test voltage to rms of 1.34 to 1.49

Voltage： 230V

Frequency： 50Hz

THD： 0.11%

rms： 1.42

P

3

Maximum permitted uncertainty of measurement when MCR ≤ 10 Note ：Pmpv means Measured power value

MCR: Umr：W(Pmpv≥1W) Uma：W(Pmpv 10

1. AP mode_2.4GHz

Idle mode (Pmpv≥1W) MCR：17.86

Umr：2.84%

Upc：3.26%

As Umr (2.84%) < Upc (3.26%), the result is acceptable.

On-State mode (Pmpv≥1W)

P




TB-M15 Rev.A

No.

General conditions for measurements

& Power management uncertainty

Measuring result Verdict

MCR：17.86

Umr：2.70%

Upc：2.96%


2. AP mode_5GHz

Idle mode (Pmpv≥1W) MCR：16.54

Umr：2.78%

Upc：3.05%


On-State mode (Pmpv≥1W) MCR：14.18

Umr：2.57%

Upc：2.67%


3. AP mode_1 Fast Ethernet port

Idle mode (Pmpv




TB-M15 Rev.A

Attachment 1: Pictures of product




TB-M15 Rev.A

Attachment 2: Instrument and Equipment.

1. AP mode_2.4GHz

2. AP mode_5GHz




TB-M15 Rev.A

3. AP mode_1 Fast Ethernet port




TB-M15 Rev.A

Attachment 3: Equipment list

www.zyxel.com

Reduction of energy consumption with reference to ON target of Code

of Conduct

The Environmental Declaration of ZyXEL Communications Corporation, WRE6505 -

Wireless Range Extender states that, in its use phase, the product, the energy

consumption in the use phase – ON state and the consequent CO2 equivalent emissions are reduced by about 39.57%. In the following, the detailed calculation is

reported.

Summary of energy consumption

In the following, the target energy consumption values of Code of Conduct are reported,

together with the new values measured for the WRE6505 - Wireless Range Extender.

Prodotto ON State (W)

Full power energy yearly consumption

(kWh)

CoC v5 Tier 2015 - 2016

9.40 13.724

WRE6505 - Wireless Range Extender

5.68 8.293

The “duty cycle” is the energy consumption derived from the power consumption in the two mentioned operational states (low power and full power), referred to 365 days of

operation. Following the ETNO document “Green benchmark: requirements for the reference boards”, the energy consumption referred to the single year is derived from a weighted sum of the power consumption of the two main operational states, depending

on the type and frequency of the home networking services used. The table illustrates

the result of the duty cycle calculation in kWh for the single product for the ON state

only, corresponding to 4 hours of operation per day.

From the table it is possible to calculate that the max. Energy consumption reduction is

equal to 39.57%.

As already said, release modifications can cause small variations of the energy

consumption; the FW release evolutions will be continuously monitored by ZyXEL

Communications Corporation to check if they will significantly affect the energy

efficiency of the product and could require modifications of the Environmental

Declaration.

Informazione al cliente – Information to customer

Wireless range extender WRE6505

Manufactured by Zyxel

Dichiarazione Ambientale – Environmental declaration

Documentazione di supporto – backup support

ECODESIGN DOCUMENTATION

Plastic datasheet

Disassembling

Packaging

��

��

��

��

�� !��"�#$��

�� !�"�#$��%&��' ��"&%�( ")*+$,�*-$��$#*

�)"�+' .��/$ � � �

�� //� ��** 01 0� ��$� /- �#

�� 2� 345 6 � �6� �� 6�

�25 345%�3� � 6 �6� �� 6�

�25 345%�3� 5 6 �6� �� 6�

��%��&��%��'��(��)�*�+��,- � ��)��%��'��(�+��,- 4

��%��%��(�.�+'/0��,- 6� /��1��&��2�+34*��.��,�- ��

��(./��(��%��%��'��(��+�/��,- � ��(.�/��!�5��1%%��%��+�"�6,- �

��7��2�+8,- 494

��4�()#�!�$�� (#,�� (*$7)#+ $*-$�##�$8-�*( $#�9�# �:)��$#�);+#%1�#$ �8-�*( $�",

//$ *)�")"

�� ,�"�$7)#+9�

65�69��

��

��

�+)�'"$**

�$*#��/$ �$*#�$#+�, 9")#* �$*#$,�//� 3��($

.��//�!)�)#� ��5�?�4��4�5%

��5�?�4��465 ��**�� 2� 345��

�25 345%�3��

�25 345%�3��

��741) $.��//�!)�)#��1.� ��5�?�464�6 � �2� ?�5

�25 ?�5

�25 ?�5

��741) $

;")#)�"��1�� 5�?�464�� 4 4

��/-� �#):$� ��')";

",$8 ��5��6 3��#*��8� 4 4

�� $**( $ ��5�?�4�546 � 4 4

�@0$�#A$��$�#)�"��2�5�� @

Component - Plastics E207780

SABIC INNOVATIVE PLASTICS JAPAN L L C

PACIFIC GRADES - RESIN, 2-2 KINUGAOKA, MOKA-SHI TOCHIGI-KEN 321-4392 JP

925A(GG), 945A(GG), 955A(GG)Polycarbonate (PC), "Lexan", furnished as pellets

Min Thk Flame RTI RTI RTI

Color (mm) Class HWI HAI Elec Imp Str

ALL 0.8 V-2 3 4 130 120 125

1.0 V-2 3 4 130 120 125

1.5 V-2 3 3 130 120 125

2.3 V-2 3 3 130 120 130

2.5 V-1 3 3 130 120 130

3.0 V-0 2 3 130 120 130

Comparative Tracking Index (CTI): 2 Dimensional Stability (%): 0

High-Voltage Arc Tracking Rate (HVTR):

3 High Volt, Low Current Arc Resis (D495): 7

Dielectric Strength (kV/mm): 39 Volume Resistivity (10x ohm-cm) : 16

(GG) - Denotes a global grade formulation previously in File E161759.

NOTE - Material designation may be followed by a color nomenclature consisiting of either an alpha/numeric or numeric/alpha combination.

ANSI/UL 94 small-scale test data does not pertain to building materials, furnishings and related contents. ANSI/UL 94 small-scale test data is intended solely for determining the flammability of plastic materials used in the components and

parts of end-product devices and appliances, where the acceptability of the combination is determined by UL.

Report Date: 2001-04-06 Last Revised: 2007-01-31 Underwriters Laboratories Inc®

IEC and ISO Test Methods

Thickness

Test Name Test Method Units Tested (mm) Value

Flammability IEC 60695-11-10 Class (color) 0.8 V-2 (ALL)

1.0 V-2 (ALL)

1.5 V-2 (ALL)

2.3 V-2 (ALL)

2.5 V-1 (ALL)

3.0 V-0 (ALL)

Glow-Wire Flammability (GWFI) IEC 60695-2-12 C 0.8 875

1.0 960

1.5 960

2.3 960

2.5 960

3.0 960

Glow-Wire Ignition (GWIT) IEC 60695-2-13 C 0.8 800

1.0 800

1.5 800

2.3 800

2.5 800

3.0 800

IEC Comparative Tracking Index IEC 60112 Volts (Max) - -

IEC Ball Pressure IEC 60695-10-2 C - -

ISO Heat Deflection (1.80 MPa) ISO 75-2 C - -

ISO Tensile Strength ISO 527-2 MPa - -

ISO Flexural Strength ISO 178 MPa - -

ISO Tensile Impact ISO 8256 kJ/m2 - -

ISO Izod Impact ISO 180 kJ/m2 - -

ISO Charpy Impact ISO 179-2 kJ/m2 - -

Underwriters Laboratories Inc®

Page 1 of 1UL iQ™ for Plastics

2014/7/30mhtml:file://J:\資材部\原料資訊\UL卡\PC及含纖\SABIC,PC,945A UL1.mht

Makrolon 6485

Page 1 of 4 pages

Makrolon®

Edition 10.02.2010 ISO Datasheet

Flame retardant grades / Medium viscosity Global grade; MVR (300 °C/1.2 kg) 9.5 cm³/10 min; Flame retardant; UL 94V-0/1.5 mm and 5VA/3.0mm; Medium viscosity; Easy release; Injection molding - Melt temperature 280 - 320 °C; Available inopaque colors only

ISO Shortname ISO 7391-PC,MFR,(,,)-09-9

Property Test Condition Unit Standard Value-

Rheological properties

C Melt volume-flow rate 300 °C; 1.2 kg cm³/10 min ISO 1133 9.5

C Molding shrinkage, parallel 60x60x2; 500 bar % ISO 294-4 0.65

C Molding shrinkage, normal 60x60x2; 500 bar % ISO 294-4 0.7

Molding shrinkage, parallel/normal Value range based on general

practical experience

% b.o. ISO 2577 0.6 - 0.8

Melt mass-flow rate 300 °C; 1.2 kg g/10 min ISO 1133 10

Mechanical properties (23 °C/50 % r. h.)

C Tensile modulus 1 mm/min MPa ISO 527-1,-2 2400

C Yield stress 50 mm/min MPa ISO 527-1,-2 66

C Yield strain 50 mm/min % ISO 527-1,-2 6.1

C Nominal strain at break 50 mm/min % ISO 527-1,-2 > 50

Stress at break 50 mm/min MPa ISO 527-1,-2 65

Strain at break 50 mm/min % b.o. ISO 527-1,-2 115

C Tensile creep modulus 1 h MPa ISO 899-1 2200

C Tensile creep modulus 1000 h MPa ISO 899-1 1900

Flexural modulus 2 mm/min MPa ISO 178 2400

Flexural strength 2 mm/min MPa ISO 178 98

Flexural strain at flexural strength 2 mm/min % ISO 178 7.1

Flexural stress at 3.5 % strain 2 mm/min MPa ISO 178 74

C Charpy impact strength 23 °C kJ/m² ISO 179-1eU N

C Charpy impact strength -30 °C kJ/m² ISO 179-1eU N

Charpy impact strength -60 °C kJ/m² ISO 179-1eU N

Charpy notched impact strength 23 °C; 3 mm kJ/m² ISO 7391/b.o. ISO

179-1eA

70P(C)

Charpy notched impact strength -30 °C; 3 mm kJ/m² ISO 7391/b.o. ISO

179-1eA

14C

Izod notched impact strength 23 °C; 3.2 mm kJ/m² b.o. ISO 180-A 80P(C)

Izod notched impact strength -30 °C; 3.2 mm kJ/m² b.o. ISO 180-A 14C

C Puncture maximum force 23 °C N ISO 6603-2 5200

C Puncture maximum force -30 °C N ISO 6603-2 6000

C Puncture energy 23 °C J ISO 6603-2 50

C Puncture energy -30 °C J ISO 6603-2 55

Ball indentation hardness N/mm² ISO 2039-1 115

Makrolon 6485

Page 2 of 4 pages

Makrolon®



Thermal properties

C Temperature of deflection under load 1.80 MPa °C ISO 75-1,-2 124

C Temperature of deflection under load 0.45 MPa °C ISO 75-1,-2 136

C Vicat softening temperature 50 N; 50 °C/h °C ISO 306 144

Vicat softening temperature 50 N; 120 °C/h °C ISO 306 145

C Coefficient of linear thermal expansion, parallel 23 to 55 °C 10-4

/K ISO 11359-1,-2 0.65

C Coefficient of linear thermal expansion, transverse 23 to 55 °C 10-4

/K ISO 11359-1,-2 0.65

C Burning behavior UL 94 (1.5 mm) [UL recognition] 1.5 mm Class UL 94 V-0

C Burning behavior UL 94 [UL recognition] 3.0 mm Class UL 94 V-0

Burning behavior UL 94 [UL recognition] 6.0 mm Class UL 94 V-0

C Burning behavior UL 94-5V [UL recognition] 3.0 mm Class UL 94 5VA

Burning behavior UL 94-5V [UL recognition] 6.0 mm Class UL 94 5VA

C Oxygen index Method A % ISO 4589-2 35

Thermal conductivity 23 °C W/(m·K) ISO 8302 0.20

Resistance to heat (ball pressure test) °C IEC 60695-10-2 136

Temperature index (Tensile strength) 20000 h; 1.5 mm °C IEC 60216-1 130

Halving interval (Tensile strength) 1.5 mm °C IEC 60216-1 7.3

Temperature index (Tensile impact strength) 20000 h; 1.5 mm °C IEC 60216-1 125

Halving interval (Tensile impact strength) 1.5 mm °C IEC 60216-1 7.0

Temperature index (Electric strength) 20000 h; 1.5 mm °C IEC 60216-1 135

Halving interval (Electric strength) 1.5 mm °C IEC 60216-1 9.7

Relative temperature index (Tensile strength) [UL recognition] 1.5 mm °C UL 746B 125

Relative temperature index (Tensile impact strength) [UL recognition] 1.5 mm °C UL 746B 115

Relative temperature index (Electric strength) [UL recognition] 1.5 mm °C UL 746B 125

Glow wire test (GWFI) [UL recognition] 0.75 mm °C IEC 60695-2-12 960




Glow wire test (GWIT) 0.8 mm °C IEC 60695-2-13 850



Glow wire test 1.5 mm °C b.o. EDF HN60 E.02 750

Glow wire test 3.0 mm °C b.o. EDF HN60 E.02 750

Application of flame from small burner Method K and F; 2.0 mm Class DIN 53438-1,-3 K1, F1

Needle flame test Method K; 1.5 mm s IEC 60695-11-5 120



Needle flame test Method F; 1.5 mm s IEC 60695-11-5 120



Burning rate (US-FMVSS) >=1.0 mm mm/min ISO 3795 passed

Flammability to CSTB 2 mm Rating NF P 92-501 M1



Flash ignition temperature °C ASTM D1929 460

Self ignition temperature °C ASTM D1929 530

Makrolon 6485

Page 3 of 4 pages

Makrolon®



Electrical properties (23 °C/50 % r. h.)

C Relative permittivity 100 Hz - IEC 60250 3.1

C Relative permittivity 1 MHz - IEC 60250 3.0

C Dissipation factor 100 Hz 10-4 IEC 60250 8

C Dissipation factor 1 MHz 10-4 IEC 60250 90

C Volume resistivity Ohm·m IEC 60093 1E14

C Surface resistivity Ohm IEC 60093 1E16

C Electrical strength 1 mm kV/mm IEC 60243-1 34

C Comparative tracking index CTI Solution A Rating IEC 60112 225

Comparative tracking index CTI M Solution B Rating IEC 60112 125M

Electrolytic corrosion Rating IEC 60426 A1

Other properties (23 °C)

C Water absorption (saturation value) Water at 23 °C % ISO 62 0.30

C Water absorption (equilibrium value) 23 °C; 50 % r. h. % ISO 62 0.12

C Density kg/m³ ISO 1183-1 1200

Bulk density Pellets kg/m³ ISO 60 640

Processing conditions for test specimens

C Injection molding-Melt temperature °C ISO 294 300

C Injection molding-Mold temperature °C ISO 294 80

C Injection molding-Injection velocity mm/s ISO 294 200

C These property characteristics are taken from the CAMPUS plastics data bank and are based on the international catalogue of basic data forplastics according to ISO 10350.

Impact properties: N = non-break, P = partial break, C = complete break

Makrolon 6485

Page 4 of 4 pages

Makrolon®


Disclaimer

Disclaimer for Sales products

This information and our technical advice - whether verbal, in writing or by way of trials - are given in good faith but without warranty, and this also applies where proprietary rights of third partiesare involved. Our advice does not release you from the obligation to check its validity and to test our products as to their suitability for the intended processes and uses. The application, use andprocessing of our products and the products manufactured by you on the basis of our technical advice are beyond our control and, therefore, entirely your own responsibility. Our products are sold inaccordance with the current version of our General Conditions of Sale and Delivery.

Test values

Unless specified to the contrary, the values given have been established on standardized test specimens at room temperature. The figures should be regarded as guide values only and not asbinding minimum values. Please note that, under certain conditions, the properties can be affected to a considerable extent by the design of the mold/die, the processing conditions and coloring.

Processing note

Under the recommended processing conditions small quantities of decomposition product may be given off during processing.To preclude any risk to the health and well-being of the machineoperatives, tolerance limits for the work environment must be ensured by the provision of efficient exhaust ventilation and fresh air at the workplace in accordance with the Safety Data Sheet. Inorder to prevent the partial decomposition of the polymer and the generation of volatile decomposition products, the prescribed processing temperatures should not be substantially exceeded.

Publisher: Global Innovations - Polycarbonates

Bayer MaterialScience AG,

D-51368 Leverkusen,

www.bayermaterialscience.com

[email protected]

Lexan* Resin FXE141R

Europe-Africa-Middle East: COMMERCIAL

LEXAN FXE141R is a medium viscosity multi purpose UV stabilized grade for visual effects in "energy". The material contains a release agent to ensure easy

processing.

TYPICAL PROPERTIES ¹ TYPICAL VALUE UNIT STANDARD

MECHANICAL

Taber Abrasion, CS-17, 1 kg 10 mg/1000cy GE Method

Tensile Stress, yield, 50 mm/min 63 MPa ISO 527

Tensile Stress, break, 50 mm/min 70 MPa ISO 527

Tensile Strain, yield, 50 mm/min 6 % ISO 527

Tensile Strain, break, 50 mm/min 110 % ISO 527

Tensile Modulus, 1 mm/min 2350 MPa ISO 527

Flexural Stress, yield, 2 mm/min 90 MPa ISO 178

Flexural Modulus, 2 mm/min 2300 MPa ISO 178

Hardness, H358/30 95 MPa ISO 2039-1

IMPACT

Izod Impact, notched 80*10*4 +23°C 12 kJ/m² ISO 180/1A

Izod Impact, notched 80*10*4 -30°C 10 kJ/m² ISO 180/1A

THERMAL

Thermal Conductivity 0.2 W/m-°C ISO 8302

CTE, 23°C to 80°C, flow 7.E-05 1/°C ISO 11359-2

Ball Pressure Test, 125°C +/- 2°C PASSES - IEC 60695-10-2

Vicat Softening Temp, Rate B/50 141 °C ISO 306


HDT/Be, 0.45MPa Edgew 120*10*4 sp=100mm 136 °C ISO 75/Be

HDT/Ae, 1.8 MPa Edgew 120*10*4 sp=100mm 125 °C ISO 75/Ae

PHYSICAL

Mold Shrinkage on Tensile Bar, flow (2) 0.5 - 0.7 % GE Method

Density 1.2 g/cm³ ISO 1183

Water Absorption, (23°C/sat) 0.35 % ISO 62

Moisture Absorption (23°C / 50% RH) 0.15 % ISO 62

Source, GMD, Last Update:08/19/2003

PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA All information, recommendation or advice given by SABIC Innovative Plastics IP BV, or any of its subsidiaries, affiliates orauthorized representatives, whether written or oral, is given in good faith, to the best of its knowledge and based on current procedures in effect. Each user of the products shall convince himself, through allavailable sources (including finished product testing in its appropriate environment) of the suitability of the products supplied for its own particular purpose. Because actual use of the products by the user isbeyond the control of SABIC INNOVATIVE PLASTICS HOLDING BV, its subsidiaries and affiliates, such use is in the exclusive responsibility of the user. SABIC INNOVATIVE PLASTICS HOLDING BV, itssubsidiaries and affiliates cannot be held responsible respectively liable for any loss incurred through incorrect or faulty use of the products. Information, recommendations and/or advice are neither made toinfringe on any patents, nor to grant a license under any patent or intellectual property right of SABIC INNOVATIVE PLASTICS HOLDING BV or any of its subsidiaries or affiliated companies, nor to grant the rightto file for any patent protection

* Lexan is a trademark of SABIC INNOVATIVE PLASTICS HOLDING BV

© 1997-2007 SABIC INNOVATIVE PLASTICS HOLDING BV.All rights reserved

1)Typical values only. Variations within normal tolerances are possible for variose colours.All values aremeasured at least after 48 hoursstorage at 230C/50% relative humidity.All properties, expect the melt volume rate are measured on injectionmoulded samples.All samples are prepared according to ISO 294.

2)Only typical data for material selection purpose.Not to be used forpart or tool design.3)This rating is not intended to reflect hazards presented by this or anyother material under actual fire conditions.4)Own measurement according to UL.




PHYSICAL


Melt Volume Rate, MVR at 300°C/1.2 kg 11 cm³/10 min ISO 1133

OPTICAL

Refractive Index 1.586 - ISO 489

ELECTRICAL

Volume Resistivity >1.E+15 Ohm-cm IEC 60093

Surface Resistivity, ROA >1.E+15 Ohm IEC 60093

Dielectric Strength, in oil, 3.2 mm 17 kV/mm IEC 60243-1

Relative Permittivity, 50/60 Hz 2.7 - IEC 60250

Relative Permittivity, 1 MHz 2.7 - IEC 60250

Dissipation Factor, 50/60 Hz 0.001 - IEC 60250

Dissipation Factor, 1 MHz 0.01 - IEC 60250

FLAME CHARACTERISTICS

UL Compliant, 94HB Flame Class Rating (3)(4) 0.7 mm UL 94 by GE

UL Compliant, 94HB Flame Class Rating 2nd value (3)(4) 3 mm UL 94 by GE

Glow Wire Flammability Index 850°C, passes at 1 mm IEC 60695-2-12


PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA All information, recommendation or advice given by SABIC INNOVATIVE PLASTICS HOLDING BV, or any of its subsidiaries,affiliates or authorized representatives, whether written or oral, is given in good faith, to the best of its knowledge and based on current procedures in effect. Each user of the products shall convince himself,through all available sources (including finished product testing in its appropriate environment) of the suitability of the products supplied for its own particular purpose. Because actual use of the products by theuser is beyond the control of SABIC INNOVATIVE PLASTICS HOLDING BV, its subsidiaries and affiliates, such use is in the exclusive responsibility of the user. SABIC INNOVATIVE PLASTICS HOLDING BV, itssubsidiaries and affiliates cannot be held responsible respectively liable for any loss incurred through incorrect or faulty use of the products. Information, recommendations and/or advice are neither made toinfringe on any patents, nor to grant a license under any patent or intellectual property right of SABIC INNOVATIVE PLASTICS HOLDING BV or any of its subsidiaries or affiliated companies, nor to grant the rightto file for any patent protection

* Lexan is a trademark of SABIC Innovative Plastics IP BV

© 1997-2007 SABIC Innovative Plastics IP BV.All rights reserved









PROCESSING PARAMETERS TYPICAL VALUE UNIT

Injection Molding

Drying Temperature 120 °C

Drying Time 2 - 4 hrs

Maximum Moisture Content 0.02 %

Melt Temperature 280 - 310 °C

Nozzle Temperature 270 - 290 °C

Front - Zone 3 Temperature 280 - 310 °C

Middle - Zone 2 Temperature 270 - 290 °C

Rear - Zone 1 Temperature 260 - 280 °C

Hopper Temperature 60 - 80 °C

Mold Temperature 80 - 110 °C







Lexan* Resin 945A


Lexan* 945A Polycarbonate (PC) resin is a non-filled, injection moldable grade. This non-chlorinated, non-brominated flame retardant PC has an UL-94 V0

rating and is available in transparent and tinted color options. Lexan 945A is a general purpose resin designed to meet the needs of various applications.


MECHANICAL

Tensile Stress, yield, 50 mm/min 63 MPa ISO 527

Tensile Stress, break, 50 mm/min 65 MPa ISO 527

Tensile Strain, yield, 50 mm/min 6 % ISO 527

Tensile Strain, break, 50 mm/min 100 % ISO 527

Tensile Modulus, 1 mm/min 2350 MPa ISO 527

Flexural Stress, yield, 2 mm/min 90 MPa ISO 178

Flexural Modulus, 2 mm/min 2300 MPa ISO 178

Hardness, H358/30 95 MPa ISO 2039-1

IMPACT

Izod Impact, unnotched 80*10*3 +23°C NB kJ/m² ISO 180/1U

Izod Impact, unnotched 80*10*3 -30°C NB kJ/m² ISO 180/1U

Izod Impact, notched 80*10*3 +23°C 70 kJ/m² ISO 180/1A

Izod Impact, notched 80*10*3 -30°C 12 kJ/m² ISO 180/1A

Charpy 23°C, V-notch Edgew 80*10*3 sp=62mm 73 kJ/m² ISO 179/1eA

Charpy -30°C, V-notch Edgew 80*10*3 sp=62mm 14 kJ/m² ISO 179/1eA

Charpy 23°C, Unnotch Edgew 80*10*3 sp=62mm NB kJ/m² ISO 179/1eU

Charpy -30°C, Unnotch Edgew 80*10*3 sp=62mm NB kJ/m² ISO 179/1eU

THERMAL

Thermal Conductivity 0.2 W/m-°C ISO 8302

CTE, 23°C to 80°C, flow 7.E-05 1/°C ISO 11359-2

CTE, 23°C to 80°C, xflow 7.E-05 1/°C ISO 11359-2

Ball Pressure Test, 125°C +/- 2°C PASSES - IEC 60695-10-2


Source, GMD, Last Update:

PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA All information, recommendation or advice given SABIC Innovative Plastics IP BV, or any of its subsidiaries, affiliates orauthorized representatives, whether written or oral, is given in good faith, to the best of its knowledge and based on current procedures in effect. Each user of the products shall convince himself, through allavailable sources (including finished product testing in its appropriate environment) of the suitability of the products supplied for its own particular purpose. Because actual use of the products the user isbeyond the control of SABIC INNOVATIVE PLASTICS HOLDING BV, its subsidiaries and affiliates, such use is in the exclusive responsibility of the user. SABIC INNOVATIVE PLASTICS HOLDING BV, itssubsidiaries and affiliates cannot be held responsible respectively liable for any loss incurred through incorrect or faulty use of the products. Information, recommendations and/or advice are neither made toinfringe on any patents, nor to grant a license under any patent or intellectual property right of SABIC INNOVATIVE PLASTICS HOLDING BV or any of its subsidiaries or affiliated companies, nor to grant the rightto file for any patent protection

* Lexan is a trademark of SABIC INNOVATIVE PLASTICS HOLDING BV

© 1997-2009 SABIC INNOVATIVE PLASTICS HOLDING BV.All rights reserved


2)Only typical data for material selection purpose.Not to be used forpart or tool design.3)This rating is not intended to reflect hazards presented this or anyother material under actual fire conditions.4)Own measurement according to UL.

Lexan* Resin 945A



THERMAL


HDT/Be, 0.45MPa Edgew 120*10*4 sp=100mm 136 °C ISO 75/Be

HDT/Ae, 1.8 MPa Edgew 120*10*4 sp=100mm 125 °C ISO 75/Ae

Relative Temp Index, Elec 130 °C UL 746B

Relative Temp Index, Mech w/impact 120 °C UL 746B

Relative Temp Index, Mech w/o impact 125 °C UL 746B

PHYSICAL

Mold Shrinkage on Tensile Bar, flow (2) 0.5 - 0.7 % SABIC Method

Density 1.2 g/cm³ ISO 1183

Water Absorption, (23°C/sat) 0.35 % ISO 62


Melt Volume Rate, MVR at 300°C/1.2 kg 10 cm³/10 min ISO 1133

ELECTRICAL

Comparative Tracking Index (UL) {PLC} 2 PLC Code UL 746A

Volume Resistivity >1.E+15 Ohm-cm IEC 60093

Surface Resistivity, ROA >1.E+15 Ohm IEC 60093

Dielectric Strength, in oil, 3.2 mm 17 kV/mm IEC 60243-1

Relative Permittivity, 50/60 Hz 2.7 - IEC 60250

Relative Permittivity, 1 MHz 2.7 - IEC 60250

Dissipation Factor, 50/60 Hz 0.001 - IEC 60250

Dissipation Factor, 1 MHz 0.01 - IEC 60250

Comparative Tracking Index 225 V IEC 60112


UL Recognized, 94V-2 Flame Class Rating (3) 1.5 mm UL 94

UL Recognized, 94V-0 Flame Class Rating (3) 3 mm UL 94

Glow Wire Flammability Index 960°C, passes at 1 mm IEC 60695-2-12


PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA All information, recommendation or advice given SABIC INNOVATIVE PLASTICS HOLDING BV, or any of its subsidiaries,affiliates or authorized representatives, whether written or oral, is given in good faith, to the best of its knowledge and based on current procedures in effect. Each user of the products shall convince himself,through all available sources (including finished product testing in its appropriate environment) of the suitability of the products supplied for its own particular purpose. Because actual use of the products theuser is beyond the control of SABIC INNOVATIVE PLASTICS HOLDING BV, its subsidiaries and affiliates, such use is in the exclusive responsibility of the user. SABIC INNOVATIVE PLASTICS HOLDING BV, itssubsidiaries and affiliates cannot be held responsible respectively liable for any loss incurred through incorrect or faulty use of the products. Information, recommendations and/or advice are neither made toinfringe on any patents, nor to grant a license under any patent or intellectual property right of SABIC INNOVATIVE PLASTICS HOLDING BV or any of its subsidiaries or affiliated companies, nor to grant the rightto file for any patent protection









Lexan* Resin 945A




Glow Wire Ignitability Temperature, 1.0 mm 850 °C IEC 60695-2-13

Oxygen Index (LOI) 35 % ISO 4589







Lexan* Resin 945A


PROCESSING PARAMETERS TYPICAL VALUE UNIT

Injection Molding

Drying Temperature 120 °C

Drying Time 2 - 4 hrs

Maximum Moisture Content 0.02 %

Melt Temperature 280 - 310 °C

Nozzle Temperature 270 - 290 °C

Front - Zone 3 Temperature 280 - 310 °C

Middle - Zone 2 Temperature 270 - 290 °C

Rear - Zone 1 Temperature 260 - 280 °C

Hopper Temperature 60 - 80 °C

Mold Temperature 80 - 110 °C







Lexan* Resin 945A








1/1

www.zyxel.com

Environmental Product Declaration

ZyXEL Communications Corporation is committed to providing our customers with safe and

environmentally friendly products* that with the European Union Directive as well as the object of

the declaration described below is in conformity with Directive 2011/65/EU of the European

Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous

substances in electrical and electronic equipment. In addition, we guarantee that ZyXEL’s products completely comply with below directives:

* The products listed in the form as below.

I. RoHS Directive 2011/65/EU

The Restriction of the use of certain Hazardous Substances in Electrical and Electronic Equipment.

II. REACH Regulation (EC) No 1907/2006

Registration, Evaluation, Authorization and Restriction of Chemicals.

III. PPW Directive 94/62/EC

Packaging and Packaging Waste.

IV. WEEE Directive 2012/19/EU

Waste Electronics and Electrical Equipment.

Product Information:

Model Name Product Description

WRE6505 Wireless AC750 Range Extender

Date Issued:

September 21, 2015 ZyXEL Communications Corporation No. 2, Gongye E. 9th Road, Hsinchu Science Park, Hsinchu, Taiwan, R.O.C.

Richard Hsu / Senior Manager Quality Management Division

www.zyxel.com www.zyxel.com Page 1 of 13

ZyXEL WEEE 3R REPORT

ZyXEL WEEE program – Evaluation of Recyclability and Recoverability rate for ZyXEL Networked equipment

EU Directive 2012/19/EU

Company name.. ........................... : ZyXEL Communications Corporation

Address ......................................... : No. 2, Gongye E. 9th Road, Hsinchu Science Park, Hsinchu,

Taiwan, R.O.C.

Department.................................... : Quality Management Department

Report No. ..................................... : ZQ20150901001

Version.. ........................................ : 1.0

Issue date ....................................... : 2015-09-16

Reporting period ........................... : 2015-09-01 to 2015-09-16

Product category ........................... : IT and Telecommunications equipment

Test Object .................................... : Wireless Range Extender

Model name .................................. : WRE6505

P/N no. ......................................... : WRE6505-ITTI01F

Trademark ..................................... :

Power supply (I/O) ....................... : Internal Power Supply

Rating(s) ........................................ : AC 100-240V, 50/60Hz, 0.15A max.

Standard ........................................ : ZyXEL WEEE program is based on following:

Directive 2012/19/EU (WEEE Recast)

A guide to the marketing, product development and

manufacturing actions you need to take IEC 62635

Test Report Form No. ................... : ZyXEL TRF52001_2013-02-06 / Ver. 1

Number of pages (Contents) ........ : 10 pages

Number of pages (Attachments) .. : 3 pages

Reported by ... : Xavier Chang Approved by . : Emma Bao


INDEX

1. ABBREVIATIONS USED IN THE REPORT 3

2. GENERAL DESCRIPTION OF PRODUCT 4

3. DISASSEMBLING INFORMATION 6

4. CALCULATION RESULT 9

ATTACHMENT

ATTACHMENT A ：PLASTIC MATERIALS MARKING 11

ATTACHMENT B ：IDENTIFIED FOR SELECTIVE TREATMENT 12

ATTACHMENT C ：REGISTRATION RESPONSIBILITY 13


1. Abbreviations used in the report

Abbr. Full name

QMD Quality Management Department

3R Reused, Recycle, Recovery

MB MotherBoard

PSU Power supply unit

M(i) Mass of ith part (ref.: IEC/TR 62635:2012)

RCR(i) Recycling rate of the ith part in the corresponding end-of-life treatment

scenario (ref.: IEC/TR 62635:2012)

RVR(i) Recovery rate of the ith part in the corresponding end-of-life treatment

scenario (ref.: IEC/TR 62635:2012)

mEEE Total product mass (ref.: IEC/TR 62635:2012)

Recyclability Ability of waste product to be recycled, based on actual practices

Recoverability Ability of a waste product to be recovered, based on actual practices

EoL End-of-life


2. General description of Product

Picture of Product:

Copy of Marking plate:


Characteristic data:

Product total weight : 109.83 g

Product dimension : L:62.3mm * W:45.5mm * H:90.9mm

Normative reference:

Directive 2012/19/EU

IEC/TR 62635:2012, Ed.1

ISO 11469:2000 Plastics — Generic identification and marking of plastics products ISO 1043 Plastics — Generic identification and marking of plastics products Part 1: Basic polymers and their special characteristics

Part 2: Fillers and reinforcing materials

Part 3: Plasticizers

Part 4: Flame retardants

General Remarks:

"(see remark #) refers to a remark appended to the report.

" (see appended table)‖ refers to a table appended to the report. Throughout this report a point is used as the decimal separator.

The test results presented in this report relate only to the object tested.

This report shall not be reproduced except in full without the written approval of ZyXEL

Communication Corporation.


3. Disassembling information 3.1 Disassembling object:

Device

Accessaries & Assemblies

/ / /

/ / /


3.2 Derivation tree of Product

• Device

• Enclosure

• Cover case x 1

• Buttom case x 1

• Plug housing x 1

• Button with light pipe x 1

• Light pipe x 1

• Plug (Silver Metal) x 2

• Enclosure assemblies

• Screw (On housing) x 1

• MB PCBA

• MB PCBA (79mm x 50mm x 1mm) x 1

• Antenna - 1 x 1

• Antenna - 2 x 1

• Antenna - 3 x 1

• RJ45 I/O (Yellow plastic) x 1

• 2-Pin outlet (Plastic) x 1


• Screw (PCBA) x 1

• Screw (Buttom case) x 1

• Power supplier PCBA

• PA PCBA (41.8mm x 30.7mm x 2.0mm) x 1

• Transformer (Core copper) x 1

• Transformer (Black plastic) x 1

• Capacitance – 1 x 1

• Capacitance – 2 x 1

• 2-Pin Connector (Plastic) x 1


4. Calculation result Basic information: Brand name ZyXEL Recycling scenario IT & telecommunication

Model name WRE6505 Sample weight 109.83 g

Calculation information:

EoL info No Name of part Mass

(g) Material

Recyclability

mass (g)

Recoverability

mass (g)

Reusable

parts －－－－－－

Parts for

selective

treatment

2.1 MB PCBA

(79mm x 50mm x 1mm)

18.774 PCBA 2.049 18.441

3.2 PA PCBA

(41.8mm x 30.7mm x 2.0mm)

8.600 PCBA 1.500 13.500

3.5 Capacitance - 1 2.000 Capacitor

(PCB) 1.000 1.800

3.6 Capacitance - 2 0.600 Capacitor

(PCB) 0.300 0.540

Parts with

single

recyclable

material

1.1 Cover case 16.200 PC 14.580 14.580

1.2 Button with light

pipe 0.630 PC 0.567 0.567

1.3 Light pipe 0.910 PC 0.819 0.819

1.4 Plug

(Silver Metal) 11.900 Copper 11.662 11.662

1.5 Buttom case 29.630 PC 26.667 26.667

1.6 Plug housing 13.300 PC 11.970 11.970

1.7 Screw

(On housing) 0.310

Stainless steel (non-magnetic)

0.295 0.295

2.2 Antenna - 1 0.0002 Stainless

steel (non-magnetic)

0.00019 0.00019


EoL info No Name of part Mass

(g) Material

Recyclability

mass (g)

Recoverability

mass (g)



0.00019 0.00019



0.00019 0.00019

2.7 Screw

(PCBA) 0.230


0.219 0.219

2.8 Screw

(Buttom case) 1.160


1.102 1.102

3.3 Transformer

(Core copper) 2.200 Copper 2.156 2.156

Parts

difficult to

process

－－－－－－

Separation

Process

2.5 RJ45 I/O

(Yellow plastic) 1.495 PBT+PC 1.047 1.346

2.6 2-Pin outlet

(Plastic) 0.220

PA (Polyamide)

0.154 0.198

3.1 2-Pin Connector

(Plastic) 0.070

PA (Polyamide)

0.049 0.063

3.4 Transformer

(Black plastic) 1.600

PA (Polyamide)

1.120 1.440

Sum ∑( )

77.255

∑( ) 107.364

Recyclability rate ∑( ) x100% = 70.34%

Recoverability rate ∑( ) x100% = 97.75%

www.zyxel.com

ATTACHMENT A

PLASTIC MATERIALS MARKING

The main material of enclosure is PC material.

www.zyxel.com

ATTACHMENT B

IDENTIFIED FOR SELECTIVE TREATMENT

In the light of Annex VII on the Directive 2012/19/EU (so called as WEEE recast), selective

treatment for materials and components have been defined for further specificly treatment during

the end-of-life electrical and electronic equipment, which are:

No details

1 polychlorinated biphenyls (PCB) containing capacitors in accordance with Council

Directive 96/59/EC of 16 September 1996 on the disposal of polychlorinated biphenyls and

polychlorinated terphenyls (PCB/PCT) ( 1 ),

2 mercury containing components, such as switches or backlighting lamps,

3 batteries,

4 printed circuit boards of mobile phones generally, and of other devices if the surface of the

printed circuit board is greater than 10 square centimetres,

5 toner cartridges, liquid and paste, as well as colour toner,

6 plastic containing brominated flame retardants,

7 asbestos waste and components which contain asbestos,

8 cathode ray tubes,

9 chlorofluorocarbons (CFC), hydrochlorofluorocarbons (HCFC) or hydrofluorocarbons

(HFC), hydrocarbons (HC),

10 gas discharge lamps,

11 liquid crystal displays (together with their casing where appropriate) of a surface greater

than 100 square centimetres and all those back-lighted with gas discharge lamps,

12 external electric cables,

13 components containing refractory ceramic fibres as described in Commission Directive

97/69/EC of 5 December 1997 adapting to technical progress for the 23rd time Council

Directive 67/548/EEC on the approximation of the laws, regulations and administrative

provisions relating to the classification, packaging and labelling of dangerous substances

( 2 ),

14 components containing radioactive substances with the exception of components that are

below the exemption thresholds set in Article 3 of and Annex I to Council Directive

96/29/Euratom of 13 May 1996 laying down basic safety standards for the protection of the

health of workers and the general public against the dangers arising from ionizing radiation

( 3 ),

15 electrolyte capacitors containing substances of concern (height > 25 mm, diameter > 25 mm

or proportionately similar volume).

Remark: These substances, mixtures and components shall be disposed of or recovered in

compliance with Directive 2008/98/EC.

www.zyxel.com

ATTACHMENT C

REGISTRATION RESPONSIBILITY

According to Art. 12 & Art. 13 on the finacing in respect of WEEE from private households and

non-private households. Recycling fees cover costs of collection, transportation, handling,

maintenance of recycling ZyXEL network and equipment as well as solvency required in the

Decree.

Acoording to Art. 16 of Directive 2012/19/EU ―Registration, information and reporting‖.ZyXEL

has completed and fulfilled EU registration responsibility requirement which shall be registered

through their authorised representatives, for detail, please refer to the table below.

Coutry Registration No. Approved compliance scheme

UK WEE/CC0067TX (CD01/00100) Comply Direct Ltd.

DE 71587309 EAR

DK 21229237 DPA-System

… … …

For other countries registry information, please feel free to contact with ZyXEL Communications

Corporation. email to: [email protected]

mailto:[email protected]

ZyXEL Communications A/S

Per: TELECOM ITALIA Spa Alla cortese attenzione: Mr. Luca GIACOMELLO Via G. Reiss Romoli 274 - 10148 Torino (TO)

ZyXEL Communications A/S Generatorvej 8D 2730 SobØrg Denmark

Italy

Soborg DK, 26 Ottobre 2015

Subject: - Dichiarazione su imballi AC750 repeater

Il cartone usato per la produzione della scatola non è plastificato ed è riciclato al 100% -

I sacchetti di plastica che si trovano all’interno dell’imballo sono ridotti al minimo indispensabile e fatti con materiale riciclabile”

Marco Tenenti, Director ITALY

energy efficiency documentation - telecom …...tb-m15 rev.a test report for code of conduct on...

Documents