ether sam testing methodology
TRANSCRIPT
1 © 2010 EXFO Inc. All rights reserved.
EXFO - EtherSAM Testing Methodology - Dual Test Set
- SmartLoopback
2 © 2010 EXFO Inc. All rights reserved.
1 Test Setup
2 Test Result
EtherSAM:
Dual Test Set (Bi-directional Test)
3 © 2010 EXFO Inc. All rights reserved. 3 © 2010 EXFO Inc. All rights reserved.
EtherSAM – Dual Test Set
Each Direction is measured: Remote to Local: 30Mbps
Local to Remote: 70Mbps
4 © 2010 EXFO Inc. All rights reserved. 4 © 2010 EXFO Inc. All rights reserved.
› LOCAL UNIT
Dual Test Set – Enable Dual Test Set
Please enable the Dual
Test Set as per screen.
Select the unit as Local
(shown in picture)
5 © 2010 EXFO Inc. All rights reserved. 5 © 2010 EXFO Inc. All rights reserved.
Dual Test Set: Link Up & Configure the L2/L3 – Local unit
Ensure that the Link is up at Local
side (green colour as per screen)
Configure the VLAN & IP address
and Subnet Mask. If there is
gateway, enable and key in related
gateway.
6 © 2010 EXFO Inc. All rights reserved. 6 © 2010 EXFO Inc. All rights reserved.
Dual Test Set: Scan Remote Unit
Click the Scan Subnet, the remote
IP address (10.10.150.34) will be
scanned and listed.
Click the Select, the IP
10.10.150.34 will be selected. Then
Click the Connect button to
connect the remote unit.
7 © 2010 EXFO Inc. All rights reserved. 7 © 2010 EXFO Inc. All rights reserved.
Dual Test Set: Scan Remote Unit and Connect
The Remote unit 10.10.150.34 is
connected.
8 © 2010 EXFO Inc. All rights reserved. 8 © 2010 EXFO Inc. All rights reserved.
9 © 2010 EXFO Inc. All rights reserved. 9 © 2010 EXFO Inc. All rights reserved.
› REMOTE UNIT
Dual Test Set - Configuration – Remote unit
Same as Local unit, enable
the Dual Test Set, the set the
unit to Remote.
10 © 2010 EXFO Inc. All rights reserved. 10 © 2010 EXFO Inc. All rights reserved.
Dual Test Set – Link Up & Configure L2/L3 for Remote unit
Ensure the link up at the remote side
(Green colour as per screen).
Configure the VLAN & IP address
and Subnet Mask. If there is a
gateway, enable and key in the
related gateway.
11 © 2010 EXFO Inc. All rights reserved. 11 © 2010 EXFO Inc. All rights reserved.
› After the Local unit connected to the Remote unit, we can start configure the test.
Dual Test Set – EtherSAM configuration
1) From the Main Menu, click the Test
2) From the Test, click the EtherSAM
3) From the EtherSAM, click the configuration
12 © 2010 EXFO Inc. All rights reserved. 12 © 2010 EXFO Inc. All rights reserved.
Dual Test Set: Configuration of EtherSAM
Under Configuration, click on Services to
configure your streams/services.
Under the Service, you can configure No of
streams, frame size and etc.
Under the Frame Parameters, you can
select Local to Remote or Remote to Local
for each stream. The VLAN/IP/UDP can be
configure as well.
Under the SLA Parameters, you may able to
configure the CIR/bandwidth for each
stream. The threshold for Jitter, Latency and
Frame Loss can be set here.
13 © 2010 EXFO Inc. All rights reserved. 13 © 2010 EXFO Inc. All rights reserved.
Dual Test Set: EtherSAM IP configuration
Under Service, click the
IP, then prompt out the
IP configuration page,
you can configure the
Destination address,
the gateway here.
14 © 2010 EXFO Inc. All rights reserved. 14 © 2010 EXFO Inc. All rights reserved.
Dual Test Set: EtherSAM IP configuration
After configure the
Services, click the
Overview. Please check
the Service as per
screen. You can set
your test time.
After all configuration,
press the Start Button.
15 © 2010 EXFO Inc. All rights reserved. 15 © 2010 EXFO Inc. All rights reserved.
Dual Test Set: Bi-directional Test Result – NetConfig Test
NetConfig Test result for particular
single stream.
NetConfig Test Overview result for
every single streams.
*** Result will show Local to Remote and Remote to Local.
16 © 2010 EXFO Inc. All rights reserved. 16 © 2010 EXFO Inc. All rights reserved.
Dual Test Set: Bi-directional Test Result – Services Test Overview
1) Local to Remote and Remote to Local result is shown as per screen.
2) Throughput, Frame Loss, Packet Jitter and Latency = EtherSAM
17 © 2010 EXFO Inc. All rights reserved. 17 © 2010 EXFO Inc. All rights reserved.
Dual Test Set: Result for Service Test Overview
1) Under Service Test, you can see any particular stream/service.
2) You can select the Local to Remote and Remote to Local direction.
18 © 2010 EXFO Inc. All rights reserved.
1 Test Setup
2 Test Result
EtherSAM:
(Round Trip Test / SmartLoopback)
19 © 2010 EXFO Inc. All rights reserved. 19 © 2010 EXFO Inc. All rights reserved.
Round Trip Test
Remote Local
192.168.0.1
255.255.255.0
192.168.0.2
255.255.255.0
1) Both directions are measured; resulted in throughput measurement of 30Mbps
2) Result reflect both direction, but does not provide enough details to pinpoint
where is the fault.
20 © 2010 EXFO Inc. All rights reserved. 20 © 2010 EXFO Inc. All rights reserved.
Round Trip Test: Local unit
Click the EtherSAM
button, the un-check the
Dual Test Set as per
screen.
21 © 2010 EXFO Inc. All rights reserved. 21 © 2010 EXFO Inc. All rights reserved.
Round Trip Test: Link Up & Configure L2/L3
Ensure that the Link is up at Local
side (green colour as per screen)
Configure the VLAN & IP address
and Subnet Mask. If there is
gateway, enable and key in related
gateway.
22 © 2010 EXFO Inc. All rights reserved. 22 © 2010 EXFO Inc. All rights reserved.
Round Trip Test: Remote side: Link Up & Configure L2/L3
Click the SmartLoopback Ensure that the remote unit Link is
Up. Green Colour as per screen.
23 © 2010 EXFO Inc. All rights reserved. 23 © 2010 EXFO Inc. All rights reserved.
Round Trip Test: Remote side: Link Up & Configure L2/L3
Configure the VLAN & IP address
and Subnet Mask. If there is a
gateway, enable and key in the
related gateway.
24 © 2010 EXFO Inc. All rights reserved. 24 © 2010 EXFO Inc. All rights reserved.
Round Trip Test: Start the Remote Unit
Start the remote unit by click
the start button as per screen.
The Result from the Remote
Unit will be shown as above
screen.
25 © 2010 EXFO Inc. All rights reserved. 25 © 2010 EXFO Inc. All rights reserved.
- After configure the Remote Unit, then configure the Local Unit as Dual Test Set,
(configure the streams; Frame size, set the CIR/bandwidth, VLAN/IP/UPD and etc)
- Start the test on the Local Unit.
Round Trip Test: Local Unit
After configure the
Services, click the
Overview. Please check
the Service as per
screen. You can set
your test time.
After all configuration,
press the Start Button.
26 © 2010 EXFO Inc. All rights reserved. 26 © 2010 EXFO Inc. All rights reserved.
Round Trip Test: Result