ez plan reindeer

8/12/2019 Ez Plan Reindeer

1/5

P.O. Box 63928 Colorado Springs, CO 80962 719-282-3043 www.lumberjacktools.com

EZ LOG FURNITURE PLANS

21 3Building log furniture is easy as...

DRILL HOLES CUT TENONS ASSEMBLE


2/5

DRILLING COMPONENTS: Cut components to lengths. Drill holes (mortise) in components using forstner or spade bits at locations

dimensioned in each plan. Drilling depth for mortises = one third to one half log diameter unless

otherwise specified.

SAFETY:Be sure that you follow all shop rules listed from your supplier of tools,equipment, fixtures, and anything youll be using to construct this project. Weassume no responsibilities for any injuries caused while building these projects.

GENERAL SAFETY RULES: Never operate tools under the influence of alcohol, drugs or medication. You must wear safety glasses, dust mask and all other safety devices that are

required. Before installing or removing a tenon cutter, the drill must come to a complete

stop and the power must be disconnected. Do not wear gloves, loose clothing or other items that may get caught in the

moving parts. Never operate tenon cutter tool in a drill press, lathe or any other device

except for a 1/2 hand drill. The log must be secured in a vise or clamp before beginning. Failure to do so

may cause bodily harm.

GETTING STARTED:These plans are a simple way to get you started making rustic furniture. Theseplans assume you have some previous woodworking experience along with thebasic shop tools. The unique thing about making your own rustic furniture is that

you can add your own touch of character and customize it to any size or shapeyou like. Always keep in mind that rustic furniture is not meant to be perfect inshape and form as in traditional furniture and that is what gives it character andpersonality just like the creator of the piece.

COMMON ITEMS NEEDED:

Peeled logs Wood glue, wood screws 1/2 drill Lumberjack Tools dual blade tenon cutter Forstner or spade bit Draw knife Chop saw, or hand saw Vise or Log mate Palm sander & sand paper Finish of choice - polyurethane, lacquer or oil Basic shop tools (tape measure, pencil, cut off saw, cordless drill, safety

glasses, etc.)

GENERAL SAFETY AND BASIC INSTRUCTION

MORTISE (HOLE)TENON


3/5

TENON CUTTING: Measure depth of mating mortise hole, then subtract 1/4. Cut tenons with Lumberjack Tool dual blade tenon cutter. If your log is larger than the cutter will accept, then taper down the end

with the draw knife.

Cutting a straight tenon is very important for reducing assembly issues.See illustrations below.

GENERAL ASSEMBLY AND GLUE UP:With all of your pieces for the project processed, this is a good time to do anysanding. After sanding, dry test fit all components. It is very important toensure that all of your pieces are correct and fit properly. Do not attempt to gluetogether your project without first doing a dry test fit. Have some shop towelsready to wipe up any excess glue. Place glue on ends of tenons and in mortiseto begin assembling.TIPS: If your logs bind-up, twist or spin them to find the natural position. Make sure pieces are square & plumb because once the glue dries, there is

no changing.

FINISHING:Select the stain and finish type to meet your needs. Make sure you have doneall of your prep work and that your piece is clean. Follow all instructions fromyour stain and finish suppliers to ensure you get the desired results.

Proper Cutting TechniqueLog and drill on-centerResult - Straight Tenon

Improper Cutting TechniqueLog and drill off-centerResult - Crooked Tenon


4/5

EZ PL N REINDEERPARTS LIST

ITEM QTY PART NAME SIZE

1 1 EZREINDEER_A 6.00 DIA. x 18.00 LG

2 1 EZREINDEER_B 5.00 DIA. x 8.00 LG

3 4 EZREINDEER_C 2.50 DIA. x 16.00 LG

4 1 EZREINDEER_D 2.50 DIA. x 8.00 LG

5 3 EZREINDEER_E 1.50 DIA. x 7.00 LG

Assemble:Apply glue to the tenons of legs (ezreindeer_C) and angled holes of body(ezreindeer_A). Assemble parts (ezreindeer_C) to (ezreindeer_A). Apply glue totenons of (ezreindeer_D), one top hole of (ezreindeer_A) body, and the single

hole on bottom of head (ezreindeer_B). Assemble (ezreindeer_D) to body hole.Then assmeble the head to the neck piece. Apply glue to the tenons of ears andtail (ezreindeer_E) and remaining holes of body (ezreindeer_A) & head(ezreindeer_B). Assemble the tail and ears in the remaining holes. Turn the headto desired position. Using branches for antlers drill holes sized according todiameter of branches at an angle. See cover page picture. Apply glue andassemble.

AB

C

D

E


5/5

18

22

33

n1(6) PLCS

20

20

EZREINDEER_ABODY

n1(3) PLCS

1

2

8

20

20

EZREINDEER_BHEAD

1

16

20

EZREINDEER_CLEGS

n1

8

EZREINDEER_DNECK

7

n1

EZREINDEER_EEARS & TAIL

ez plan reindeer

Documents