f. garnier, p-a. giudici, f.bergsma cern mice collaboration meeting no. 28

11
F. Garnier, P-A. Giudici, F.Bergsma CERN MICE Collaboration Meeting No. 28 Absorber Systems & MICE Magnets Session 6 October 2010 technical drawings by O.Jamet Magnet Measurement Device for MICE

Upload: lotta

Post on 16-Jan-2016

31 views

Category:

Documents


0 download

DESCRIPTION

Magnet Measurement Device for MICE. F. Garnier, P-A. Giudici, F.Bergsma CERN MICE Collaboration Meeting No. 28 Absorber Systems & MICE Magnets Session 6 October 2010 technical drawings by O.Jamet. Layout. Rails. Trolley with B-sensors. Servo motor with encoder. ¼ pipe of aluminum. - PowerPoint PPT Presentation

TRANSCRIPT

Page 1: F. Garnier, P-A. Giudici, F.Bergsma CERN MICE Collaboration Meeting   No. 28

F. Garnier, P-A. Giudici, F.BergsmaCERN

MICE Collaboration Meeting No. 28

Absorber Systems & MICE Magnets Session 6 October 2010

technical drawings by O.Jamet

Magnet Measurement Device for MICE

Page 2: F. Garnier, P-A. Giudici, F.Bergsma CERN MICE Collaboration Meeting   No. 28

Servo motor with encoder

Tooth belt

Trolley with B-sensors

Support by tripods

Support by adjustment screws on cradles

Rails

Cradles

Magnet bore

¼ pipe ofaluminum

Layout

Page 3: F. Garnier, P-A. Giudici, F.Bergsma CERN MICE Collaboration Meeting   No. 28

¼ pipe ofaluminum

Rails

Cradle

Magnet bore

Disk with 7 B-sensors calibrated at 4.5 Tesla

Axis of rotation 5 degree steps

5 m

Page 4: F. Garnier, P-A. Giudici, F.Bergsma CERN MICE Collaboration Meeting   No. 28

5m version for spectrometer solenoids

2m version for focus absorber solenoids.

Extension disk to by-pass internal flange AFCNeed to measure from both sides

2m version could be used to measure eventually coupling coils

Extension disk for AFC

2 versions

Irremovable flange

Page 5: F. Garnier, P-A. Giudici, F.Bergsma CERN MICE Collaboration Meeting   No. 28

B-sensor card Stack of B-sensors in calibrator

Passive backplane for B-sensorto carry double-row connector

Daisy chain B-sensors

Double row flat-cable connector

Single-row 10 pin connector

SPI-interface

Homogeneous field region is small => need highdensity => single row connectorGlass cube with 3 Hall probes

front back

F.Bergsma/CERN IMMW16 5

thermistorFeet tolerance 50 µm

Page 6: F. Garnier, P-A. Giudici, F.Bergsma CERN MICE Collaboration Meeting   No. 28

IMMW15 F.Bergsma 6

130 mm

Calibration done at GHMFL Grenoble

Bmax=4.5 Tesla

Page 7: F. Garnier, P-A. Giudici, F.Bergsma CERN MICE Collaboration Meeting   No. 28

Mounting of B-sensors

Page 8: F. Garnier, P-A. Giudici, F.Bergsma CERN MICE Collaboration Meeting   No. 28

Measurement grid

Disk can rotate in steps of5 degree

180 mm sensor has to be removed for this region

Page 9: F. Garnier, P-A. Giudici, F.Bergsma CERN MICE Collaboration Meeting   No. 28
Page 10: F. Garnier, P-A. Giudici, F.Bergsma CERN MICE Collaboration Meeting   No. 28

DAQ + control

SPI -> RS232 interface, SPI-bus with 7 slots

Where to put interface: inside or outside 4 Tesla?

Leave both options open

DAQ program (MSVC) runs on PC (laptop)

BALDOR servo engine with NextMove ESB motion controllerESB connected with CANbus to PC

Page 11: F. Garnier, P-A. Giudici, F.Bergsma CERN MICE Collaboration Meeting   No. 28

mechanics:

1 build 5 m version , test precision 2 if precision insufficient add encoder, foresee laser tracker during measurements3 build 2 m version

DAQ:

Build simple read-out for 7 B-sensorsAnticipate to have interface outside high field region

Accuracy:

Better than 0.5 mm longitudinal+/- 0.1mm radial+/- 1 mrad directiveBx,By,Bz +/- 2 mT Check in situ with NMRSurveying done at CERN with laser tracker

STRATEGY