ganesh cfd
TRANSCRIPT
Ganesh Thiruganam, ME,(PhD).
No:593,Vivekanda Street,Gandhi Nagar, Vellore-632006
[email protected]+91-9952119645, Skype Id: ganeshr3_1
EDUCATION
Qualification School/
College
University/
Board
Year of
Passing
Stream/
Degree
Score
Doctrate VIT Chennai VIT university 2019 Phd in Oil Pump
CFD -
Post Graduate
Kingston
Engineering
College, Vellore.
Anna university 2015 M. E. Engineering
Design 7.9
Under Graduate
Kingston
Engineering
College, Vellore.
Anna university 2013 B. E. Mechanical
Engineering 7.59
Class 12
Vani Vidhyalaya
Hr. Sec. School,
Vellore.
Tamil Nadu
State Board 2009
Math, physics,
Chemistry,
Computer
Science.
79%
Class 10
Vani Vidhyalaya
Hr. Sec. School,
Vellore.
Tamil Nadu
State Board 2007 77%
EXPERIENCE
Achievement
Acquired the 7 government tenders for a garbage compactor at Thiruvalluvar district town panchyat within a
short span.
ACADEMIC TRAINING
Project Training: Undergone One and half months training in the Design Department in Hyva India PVT
LTD, Bangalore.
In-plant Training: undergone a One month training in Metropolitan Transport Corporation (Chennai)
Limited
In-plant Training: undergone a five days training in the production department at SAMEDEUTZFAHR
INDIA (P) LTD.
ACADEMIC ACHIEVEMENT
Honours & Awards
Won a Silver Medal in India Level contest titled “3D student design challenge 2014” conducted by Autodesk
Inc.( NATIONAL AWARD)
Won a 1st place in south India Level contest titled “3D student design challenge 2014” conducted by Autodesk
Inc.
Won a 4th
place in all India optimization contest titled “Altair Optimization Contest 2014” conducted by
Altair India Pvt Ltd. ( NATIONAL AWARD)
Won a 2nd
place in Inter college competition titled “Business Plan” conducted by Department of management
studies in Kingston engineering college.
Won a 1st place in Honda Safety Test Drive conducted by Honda Racing Team at Kingston Engineering
College.
Papers Published
Paper Published titled “Explicit Non Linear Dynamic Analysis of Frontal Airbag Deployment for Head
Injury Criteria with FMVSS 208” in International Journal of Applied Engineering Research, ISSN 0973-4562
Paper Published titled “SOLID RECOVERED FUEL” in “ICACT14 – International Conference” conducted by
J. K. K. Nattraja College of Engineering and Technology on 7th & 8th March 2014.
Paper Published titled “REFUSED DERIVED FUEL TO ELECTRICITY” in “International Journal of
Engineering Research & Technology, Volume 2, Issue 9 (September – 2013)” on 28th September 2013.
Paper presented & awarded
Paper presentation titled “BIODIESEL PRODUCTION FROM WASTE COOKING OIL” in Bharath University
on 27th March 2014.
Paper presentation titled “REFUSED DERIVE FUEL TO ELECTRICITY” in Vel Tech on 21st August 2012
and won second prize.
Paper presentation titled “REFUSED DERIVE FUEL” in GTEC and 10th August 2012 won third prize.
ACADEMIC PROJECT
Explicit Non Linear Dynamic Analysis of Frontal Airbag Deployment for Head Injury Criteria with
FMVSS 208 ( DEC 2014 – FEB 2015) Head Injury Criteria for human hybrid III dummy 50th percentile mid-size male while on frontal airbag
deployment at Ford Eco sport is calculated and compared with FMVSS 208 Standards
DESIGN AND ANALYSIS OF UNDER RUN PROTECTION DEVICE FOR VEHVICLE CATEGORY M2,
M3, N2, N3, T2, T3. (JAN 2014 – MAY2014)
Designed and shape Optimization of under run protection device of a Scania truck to minimize the life threat
of human undergoing an under run accident.
ROLL OVER PROTECTIVE SYSTEM (DEC 2012 – FEB 2013)
Designed and Analysis of canopy plate of a Volvo tipper body that can able to withstand a load up to 33
Tons. Doing project at HYVA INDIA PVT LTD, Bangalore.
DESIGN AND FABRICATION OF K-ROBOT (Jan 2012 – April 2012)
Designed a robot based on 4 bar kinematic linkages and power by electrical motor without any sensor and
feedback unit of electronics.
SOFTWARE SKILL
Drafting: AutoCAD.
Modeling: Autodesk Inventor, Solid works, Catia.
Analysis: Ansys ICME CFD, CFX & FLUENT, Pumplinx , Hypermesh , LS dyna.Open Foam CFD.
Additional: Google Sketchup, Adobde Photo Shop CS5.
POSITION OF RESPONSIBILITY
Senior Technical Lead Speaker on various workshops and seminars on Autodesk Inventor, Catia And
Solidworks for representing CADD Training Services at colleges.
Event Organizer for National Workshop on “Training and Practice on MATLAB coding for Thermodynamic and
Energy Systems” conducted by Dr. T. Srinivasan ,VIT University Vellore.
Executive Member for National Level Technical Symposium “Cryogen 2012”
Coordinator for various CADD contests at Kingston Engineering College.
Co-Curricular and Extra Curricular Activities
I was an Autodesk Student Expert Premium Member too.
Acted as a volunteer for Tire 1 SAE (Society of automotive Engineers), 2014th year.
Acted as Volunteer for NCC (National Cadet corps ), 2013th year.
REFERENCE
Mr.S.Thingal Selvan Bsc.,MBA.,(Ph.D), Director of Placement, Kingston Engineering College, +919382842540.
Mrs. J. Sumathy B.E., MBA.,(Ph.d), Director, CADD Training Services India Pvt Ltd. +919894634329,
Mr.V.Srinivasan B.E.,MBA., Properitor, Vaishnavi Motors India Pvt Ltd, +919444172941,