hydraulics & pneumatics
DESCRIPTION
HYDRAULICS & PNEUMATICS. Basic Concepts FluidSIM-H. Presented by: Dr. Abootorabi. Energy. Potential energy: W=m.g.h Press with elevated reservoir:. Energy. Pressure energy: W=p. Δ V. Energy. Motion energy:. Thermal energy:. Power. Power. Efficiency. - PowerPoint PPT PresentationTRANSCRIPT
![Page 1: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/1.jpg)
HYDRAULICS & PNEUMATICS
Presented by: Dr. Abootorabi
Basic ConceptsFluidSIM-H
1
![Page 2: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/2.jpg)
Energy
Potential energy:
W=m.g.h
Press with elevated reservoir:
2
![Page 3: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/3.jpg)
EnergyPressure energy:
W=p.ΔV
3
![Page 4: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/4.jpg)
EnergyMotion energy:
4
Thermal energy:
![Page 5: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/5.jpg)
Power
5
![Page 6: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/6.jpg)
Power
6
![Page 7: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/7.jpg)
Efficiency
7
![Page 8: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/8.jpg)
Calculation of input and output power
8
![Page 9: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/9.jpg)
Throttle points
9
![Page 10: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/10.jpg)
Physical Properties of Hydraulic FluidsSpecific Weight
Also known as unit weight, is the weight per unit
volume of a material.
10
Volume
=
Specific weight =Weight
W
VN.m-3 = m
Vkg.m-3
VolumeDensity =
Mass
Specific weight – Density relationship:
W = mg = g [N. m-3]
![Page 11: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/11.jpg)
Specific gravity is a dimensionless unit defined as the
specific weight of the fluid divided by the specific weight of
water.
11
water
SGoil = oil
9800 N/m3
=oil
water
Density of the oil [kg/m3]
Density of water [kg/m3]
1000 kg/m3
Specific weight of the oil [N/m3]
Specific Gravity (SG)
![Page 12: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/12.jpg)
Pressure Head It represents the height of a fluid column that produces
the static pressure.
12
g
pH =
In other words, due to its weight, a 1-ft column of water develops at its base a pressure of 0.433 psi. The 1-ft height of water is commonly called a pressure head.
0.433 psi
1 ft
Pressure - force relationship: p = F / A
Pressure - head relationship: p = H
![Page 13: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/13.jpg)
The Continuity Equation for Hydraulic Systems
13
Use of Volume Flow Rate Q
Q1(m3/s) = A1(m2) 1(m/s) = A2 2 = Q2
Flow rates are frequently specified in units of liters per second (Lps) or liters per minute (Lpm). 1m3 = 1000 L
![Page 14: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/14.jpg)
Q is the volume flow rate ( volume of fluid passing a given station per unit time).
Hence, for hydraulic systems, the volume flow rate is also constant in a pipe line. The continuity equation for hydraulic systems can be rewritten as follows:
14
(/4) D12
(/4) D221
2
=A2
A1
=
This equation shows the smaller the pipe size, the greater the velocity.
1
2
=D1
( D2 )2
Where D1 and D2 are the pipe diameters at stations 1 and 2, respectively.The final result is:
Continuity equation forhydraulic system
The Continuity Equation for Hydraulic Systems
![Page 15: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/15.jpg)
Hydraulic PowerHydraulic Cylinder
Rod
F Load
Barrel
p
Q
Piston
• Hydraulic power is the power delivered by a hydraulic fluid to a load-driving device such as hydraulic cylinder.
• Let’s analyze the hydraulic cylinder (above figure) by developing equations that will allow us to answer the following 3 questions:
15
![Page 16: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/16.jpg)
Hydraulic PowerHydraulic Cylinder
1. How do we determine how large a piston diameter is
required for the cylinder?
2. What is the pump flow rate required to drive the cylinder
through its stroke in a specific time?
3. How much hydraulic horsepower does the fluid deliver to
the cylinder?
QUESTIONS
16
![Page 17: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/17.jpg)
Pressure p acts on the area of the piston to produce
the force required to overcome the load:
17
FF loadloadA =
p
Load is known from the application
Pressure is established based on the pump design
ANSWER 1 – Piston Size
Rod
F Load
Barrel
p
Q
Piston
![Page 18: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/18.jpg)
Piston velocity
Q [m3/s] = A [m2] × [m/s]
18
ANSWER 2 – Pump Flow Rate
Piston velocityPiston area
The larger the piston area and velocity, the greater
must be the pump flow rate.
Volume displacement VD of the hydraulic cylinder = A X S
A
S
Q = VD / t
= (A X S) / t
= A X
Pump flow rate in a specific time
![Page 19: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/19.jpg)
Time
ANSWER 3 – Hydraulic power
Power =Energy
= Force X Distance= F X S= p A X S
p A S
t=
= p A = p Q
Hydraulic power (W) = p [N/m2] X Q [m3/s]
Hydraulic power (kW) = (p [bar] X Q
[lit/min])/600
or Pa
19
![Page 20: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/20.jpg)
Mechanical Power The mechanical output power delivered by a hydraulic
motor:
20
Power (W) = T (N.m) X (rad/sec)
If RPM is given , must change to rad/sec by X 2/60
![Page 21: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/21.jpg)
Introduction to FluidSIM-H Demo
21
![Page 22: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/22.jpg)
Introduction to Simulating and Creating Circuits
22
![Page 23: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/23.jpg)
Introduction to Simulating and Creating Circuits
23
![Page 24: HYDRAULICS & PNEUMATICS](https://reader037.vdocuments.pub/reader037/viewer/2022102500/568132a8550346895d994b5b/html5/thumbnails/24.jpg)
The end.
24