lecture 5 cor 1
TRANSCRIPT
-
8/21/2019 LECTURE 5 cor 1
1/44
1
LECTURE 5
(Fluid Mechanics and Thermodynamics)
1. Fluid Mechanics
1.1 PRIMARY THERMODYNAMIC PROPERTIES OF FLUIDS
Pressure (p) - is the (compression) stress at a point in a static fluid.
kPaapsiapatm 3.1017.14 Temperature (T) is a measure of the internal energy level of a fluid.
460 FR
273 CK
Density () - is its mass per unit volume.
V
m
Specific weight () - is its weight per unit volume.
V
mg
V
Wg
Specific gravity (SG) - is the ratio of a fluid density to a standard reference fluid, water (for liquids), and air (fo
gases).
air
gasgasSG
320.1 mkgair at 101.3 kPa and 21 C.
wat er
liquidliquidSG
31000 mkgwater
Example No. 1
What is the sea level (g = 32.2 ft/sec2) specific weight (lbf/ft3) of liquids with densities of 65.5 lbm/ft3?
A. 32.2
B. 42.2C. 65.5
D. 76.7
Solution:
cg
ftlbmindensitygg
3
2
3
2
232
565232
sec.
.sec.
lbfftlbm
ftlbmft
35.65 ftlbf (C)
1.2 VISCOSITY
Viscosity (1) - is that property of a real fluid by virtue of which it offers resistance to shear force.
Viscosity (2) is the fluid resistance to flow or the property of fluid to resist shear deformation.
Newtons law of viscosity states that the shear force to be applied for a deformation rate of ( dV/dy) over an area
A is given by,
dydVAF
-
8/21/2019 LECTURE 5 cor 1
2/44
2
where F is the applied force in N, A is area in m2, dV/dy is the velocity gradient (or rate of deformation), 1/s
perpendicular to flow direction, here assumed linear, and is the proportionality constant defined as the
dynamic or absolute viscosity of the fluid.
Shear Stress = dydVAF Shear Strain = AFdydV
Viscosity Index is the rate at which viscosity changes with temperature.
Viscosimeter an instrument, consisting of standard orifice, used for measuring viscosity (in SSU and SSF).
Absolute (Dynamic) Viscosity is the viscosity determined by direct measurement of shear resistance (in Poise
or centiPoise.) Units are 1 reyn = 1 lb-sec/in2, 1 Poise = 1 dyne-sec/cm2 = 0.1 Pa-sec. 1 centiPoise (cP) = 0.01
Poise.
Kinematic Viscosity it the absolute viscosity of a fluid divided by the density (in Stoke or centiStoke.) Units are
ft2/s, m2/s, 1 stoke = 1 cm2/sec. = 0.0001 m2/sec. 1 centiStoke (cSt) = 0.01 Stoke.
Example No. 2
An oil has a kinematic viscosity of 1.25 x 10-4 m2/s and a specific gravity of 0.80. What is its dynamic (absolute)
viscosity in kg/(m-s)?A. 0.08
B. 0.10
C. 0.125
D. 1.0
Solution:
= 1.25 x 10-4 m2/s
SG = 0.80
= x
= SG xw x
= 0.80 x (1000 kg/m3) x (1.25 x 10-4 m2/s)
= 0.10 kg/(m-s)
1.3 REYNOLDS NUMBER
Reynolds number is a dimensionless number which is the ratio of the forces of inertia to viscous forces of the
fluids. It is the primary parameter correlating the viscous behaviour of all newtonian fluids.
v
DVDV
ForcesViscous
inertiaofForces
Re
where:
Re = Reynolds number, dimensionless
D = inside diameter, mV = velocity, m/s
= kinematic viscosity, m2/s
= absolute viscosity, Pa-sec
Example No. 3
Water is flowing in a pipe with radius of 12 inches and a velocity of 11 m/sec. The viscosity of water is 1.131 Pa
sec. What is the Reynolds Number?
A. 2964
-
8/21/2019 LECTURE 5 cor 1
3/44
3
B. 5930
C. 58
D. 9189
Solution:
vDRe
59301311
113739
122
..
Re (B)
1.4 TYPES OF FLOW
Laminar Flow particles run parallel to each other. Laminar flow occurs if the Reynolds number is less than
2000.
Turbulent Flow particles run not in same direction. Turbulent flow occurs if the Reynolds number is greate
than 4000. Fully turbulent occurs at very high Reynolds number.
Transitional Flow also termed as critical flow in which this type of flow occurs if the Reynolds number is
between 2000 to 4000.
1.5 SURFACE TENSION AND CAPILLARY ACTION
Surface Tension is the membrane formed on the free surface of the fluid which is due to cohesive forces. Thereason why insects were able to sit on water is due to surface tension. The amount of surface tension decreases
as the temperature increases.
Capillary Action this is done through the behaviour of surface tension between the liquid and a vertical solid
surface.
1.6 COMPRESSIBILITY AND BULK MODULUS
Compressibility, - the measure of the change in volume of a substance when a pressure is exerted on thesubstance.
P
V
V
o
Where:V = change in volumeVo = original volume
P = change in pressure
Bulk modulus, EB - is defined as the ratio of the change in pressure to the rate of change of volume due to the
change in pressure. It is the inverse of compressibility.
1.7 HYDROSTATIC PRESSURE
Hydrostatic Pressure is the pressure of fluid exerted on the walls of the container.
Notes:
a. Pressure in a continuously distributed uniform static fluid varies only with vertical distance and is
independent of the shape of the container. The pressure is the same at all points on a given horizontal planein the fluid. The pressure increases with depth in the fluid.
b. Any two points at the same elevation in a continuous mass of the same static fluid will be at the same
pressure.
-
8/21/2019 LECTURE 5 cor 1
4/44
4
Pressure = Weight Density x Height
ghhp
Pressure Head,
gpph
where:
p = hydrostatic pressure (gage pressure)
h = height of liquid (pressure head)
= Density of liquid
Example No. 4
On a sea-level standard day, a pressure gage, moored below the surface of the ocean (SG = 1.025), reads an
absolute pressure of 1.4 MPa. How deep is the instrument?
A. 4 m
B. 129 m
C. 133 m
D. 140 m
Solution:
hSGhghpp watmabs
HmkNmkNmkN 322 81902513251011400 ... mh 129
Example No. 5
If the absolute pressure at the bottom of the ocean is 300 kPa, how deep is the water at this point?
A. 16.66 m
B. 19.66 m
C. 29.66 m
D. 39.66 m
Solution:
a tmga b s PPP
325.101300 gP
-
8/21/2019 LECTURE 5 cor 1
5/44
5
kPaPg 675.198
mGS
Ph
g66.19
81.903.1
675.198
..
1.8 MANOMETER
Manometer is a device to measure pressure or mostly difference in pressure using a column of liquid to balance
the pressure.
BABA pppppppppp 332211 B AB A zzzzzzzzpp 3432321211
Example No. 6
In Fig. FE2.3, if the oil in region B has SG = 0.8 and the absolute pressure at point A is 1 atm, what is the absolute
pressure at point B?
A. 5.6 kPa
B. 10.9 kPa
C. 106.9 kPa
D. 112.2 kPa
Solution:
003.0
04.008.005.0
Bwo
wmww A
pmSG
mSGmSGp
-
8/21/2019 LECTURE 5 cor 1
6/44
6
m
mmpp
w
AB
03080
04008056130501
..
....
mpp
w
AB56840.
mmkNmkNpB 56840819325101 32 ... kPapB 90106.
1.9 BUOYANCY
Buoyancy the tendency of a body to float when submerged in a fluid.
Two Archimedes Law of Buoyancy
a. A body immersed in a fluid experiences a vertical buoyant force equal to the weight of the fluid it displaces.
b. A floating body displaces its own weight in the fluid in which it floats.
BFW
VFB where:
FB = buoyant force
-
8/21/2019 LECTURE 5 cor 1
7/44
7
W = weight of the body
V = volume of the body submerged or volume of the liquid displaced
= density of the liquid
Example No. 7
A stone weighs 105 lbs in air and 83 lb in water. Find the specific gravity of the stone.
A. 2.98
B. 0.35
C. 4.77 D. 2.21
Solution:
Volume (stone) = Volume (water displaced)
33525640
462
83105ft.
.
Specific Weight (stone) = 105 / 0.352564 = 297.82 lb/ft3
Specific gravity (stone) = 297.82 / 62.4 = 4.77 (c)
Example No. 8
An iceberg has a SG of 0.922. When floating in sea water (SG = 1.03), its exposed volume in % is nearest to,
A. 5.6B. 7.4
C. 8.9
D. 10.5
Solution:
su bm erged seaiceice VSGVSG
su bm erged ice VV 03.1922.0
icesu bm erged VV 895.0
%100895.0
%ice
iceice
V
VVosedexp
%5.10% osedexp
1.10 BASIC SCIENTIFIC LAWS USED IN THE ANALYSIS OF FLUID FLOW
a. Law of conservation of mass: This law when applied to a control volume states that the net mass flow
through the volume will equal the mass stored or removed from the volume. Under conditions of steady
flow this will mean that the mass leaving the control volume should be equal to the mass entering the
volume. The determination of flow velocity for a specified mass flow rate and flow area is based on the
continuity equation derived on the basis of this law.
b. Newtons laws of motion: These are basic to any force analysis under various conditions of flow. The
resultant force is calculated using the condition that it equals the rate of change of momentum. The reaction
on surfaces are calculated on the basis of these laws. Momentum equation for flow is derived based on
these laws.
c. Law of conservation of energy: Considering a control volume the law can be stated as the energy flow into
the volume will equal the energy flow out of the volume under steady conditions. This also leads to the
situation that the total energy of a fluid element in a steady flow field is conserved. This is the basis for the
derivation of Euler and Bernoulli equations for fluid flow.
d. Thermodynamic laws: are applied in the study of flow of compressible fluids.
1.11 CONTINUITY EQUATION
-
8/21/2019 LECTURE 5 cor 1
8/44
8
Continuity Equation - This equation is used to calculate the area, or velocity in one dimensional varying area
flow, like flow in a nozzle or venturi.
2211 QQm
222111 VAVA
For incompressible flow. 21
21 QQQ
2211 VAVA
Example No. 9
Oil flow through a 30 tubes condenser with a velocity of 1.75 m/s. The internal diameter of tube is 20 mm an oil
density is 0.90 gm/mL. Find the volume flow in liters per second.
A. 16.5
B. 11.6
C. 15.6
D. 9.4
Solution:
AVQ
sec
104977.575.1020.0
4
342 m
Q
sec5.16301000sec
104977.53
34
Litubesm
LimQ
1.12 VELOCITY HEAD
Torricellis Theorem:
The velocity of a liquid which discharge under a head is equal to the velocity of a body which falls in the same
head.
g
Vh
2
2
where:
h = velocity head
V = velocity of the liquid
1.13 FRICTION HEAD LOSS IN PIPES
Darcy-Weisbach Equation
g
V
D
Lf
gD
fLVh f
22
22
where:
h f = velocity head, m or ft
V = velocity of the liquid, m/s or ft/sec
L = length of pipe, m or ftD = internal diameter, m or ft
f = coefficient of friction, friction factor (Darcy)
g = 9.81 m/s2 or 32.2 ft/sec2
Example No. 10
What is the expected head loss per mile of a closed circular pipe (17 in inside diameter, friction factor of 0.03
when 3300 gal/min of water flow under pressure?
-
8/21/2019 LECTURE 5 cor 1
9/44
9
A. 38 ft
B. 3580 ft
C. 0.007 ft
D. 0.64 ft
Solution:
sec
min
60
1
12
12313300
3
3
in
ftgalingpmQ
ecsftQ 3
352437.
fpsft
ecsft
D
QV 66454
1217
35243744
2
3
2.
.
g
V
D
Lfh f
2
2
ftmileL 52801
2322
66454
1217
5280030
2
.
.. f h
fth f 7837.1.14 COEFFICIENT OF FRICTION, f
a. Coefficient of friction for laminar flow (Re < 2300).
Re
64f
b. Coefficient of friction for turbulent flow
Colebrook equation, turbulent flow only (Re > 2300)
7.3Re
51.2log2
21
D
ff
where, = nominal roughness of pipe or duct being used
A good approximate equation for the turbulent region of the Moody chart is given by Haalands equation:2
11.1
7.3Re
9.6log8.1
D
f
H. Blasius Equation (4000 < Re < 105)
4 Re
316.0f
Example No. 11
For flow of water at a Reynolds number of 1.03 x 106 through a 5-cm-diameter pipe of roughness height 0.5 mm
the approximate Moody friction factor is
A. 0.012
B. 0.018
C. 0.038
-
8/21/2019 LECTURE 5 cor 1
10/44
10
D. 0.049
Solution:
Use Haaland approximation to Colebrook equation, Re > 2300
2111
73
9681
.
.Re
.log.
Df
2111
6 73
5050
10031
9681
.
.
.
.
.
log.f
0380.f
1.15 HYDRAULIC DIAMETER
For flow in non-circular ducts or ducts for which the flow does not fill the entire cross-section, we can define the
hydraulic diameter
P
ADh
4
where
A = cross-sectional area of actual flow,
P = wetted perimeter, i.e. the perimeter on which viscous shear acts
Example No. 12
Air at atmospheric pressure and with a mean velocity of 1.0 m/s, flows inside a square section duct of side b = 4
cm. If the air temperature is 350 K, determine the Reynolds Number. (at 350 K, viscosity = 20.76 x 10 -6 m2/s.)
A. Re = 1296.8
B. Re = 1926.8
C. Re = 1629.8
D. Re = 1962.8
Solution:
Hydraulic Diameter for square duct
mcmbb
bD 040444
2
.
81926
107620
01040
6.
.
..Re
DV(B)
Example No. 13
What is the hydraulic diameter of a rectangular air-ventilation duct whose cross section is 1 m by 25 cm?
A. 25 cm
B. 40 cm
C. 50 cm
D. 75 cm
Solution:
P
ADh
4
cmcm
cmcmDh 40
251002
251004
1.16 BERNOULLIS EQUATION
-
8/21/2019 LECTURE 5 cor 1
11/44
11
Bernoullis equation is a general energy equation that is used for solving fluid flows. It relates elevation head
pressure head and velocity head. Some conditions of using Bernoullis equation: (1) No fluid friction, (2) fluid is
incompressible, and (3) negligible changes in thermal energy.
Bernoullis theorem Neglecting friction, the sum of the pressure head, velocity head and elevation head of a
point is equal to the sum of the pressure head, velocity head and elevation head of another point.
2
222
1
211
22Z
g
VpZ
g
Vp
where:
Pressure head =
p
Velocity head =g
V
2
2
Elevation head = Z
Example No. 14
Water flows through a horizontal pipe of cross sectional area of 20 cm2. At one section the cross sectional area is
4 cm2. The pressure difference between the two sections is 29.4 psi. How many cu. meters of water will flow out
of the pipe in 1 minute?
A. 1.208 m3
B. 0.0185 m3
C. 0.493 m3
D. 0.008 m3
Solution:
g
VVpp
2
21
2221
2211 VAVAQ
21 420 VV
12 5VV
21
21
22
2
pp
g
VV
kPapsi
kPapsipp 705.202
696.14
325.1014.2921
3
2
2
21
21
81.9
705.202
81.92
5
mkN
mkN
sm
VV
smV 11.41
smcmm
cmVAQ 11.4100
1
20
2
2
11
smQ33
1022.8
In 1 min.
Volume = (8.22 x 10-3)(60) = 0.4932 m3
Example No. 15
-
8/21/2019 LECTURE 5 cor 1
12/44
12
A perfect venturi with throat diameter of 1.8 inches is placed horizontally in a pipe with a 5 in inside diameter
Eighty (80) lbm of water flow through the pipe each second. What is the difference between the pipe and
venture throat static pressure?
A. 29.9 psi
B. 34.8 psi
C. 5020 psi
D. 72.3 psi
Solution:
sftftlb
slbQ
3
3 282051
462
80.
.
fpsD
QV 40249
125
28205144
22
1
1.
.
fpsD
QV 549272
1281
28205144
22
2
2.
.
.
g
VVpp
2
2
1
2
221
2322
40249549272462144
22
21
...
. pp
psipp 823421
.
1.17 VENTURI, NOZZLE AND ORIFICE METERS
Venturi, Nozzle and Orifice meters are the three obstruction type meters commonly used for the measuremen
of flow through pipes.
Flow Rate:
ghAA
A
Q 212
12
2
This equation needs a modifying coefficient as viscous effects and boundary roughness as well as the velocity o
approach factor that depend on the diameter ratio have been neglected.
The coefficient is defined by,
dl theoreticaactual CQQ where Cd is the coefficient of discharge. Cd for venturi meters is in the range 0.95 to 0.98. Cd for flow nozzle is in
the range 0.7 to 0.9 depending on diameter ratio and Reynolds number to some extent. For orifice, The range
for coefficient of discharge is 0.6 to 0.65.
1.18 DISCHARGE MEASUREMENT USING ORIFICESActual flow rate:
ghACQ dact ual 20
where A0 is the area of orifice and Cd is the coefficient of discharge.
l theoretica
actual d
Q
QC
Coefficient of velocity Cv.
-
8/21/2019 LECTURE 5 cor 1
13/44
13
gh
V
velocitylTheoretica
contractavenaatjetofvelocityA ctualC v
2
The value of Cv varies from 0.95 to 0.99 for different orifices depending on their shape and size.
Coefficient of contraction Cc.
0A
A
velocityofArea
contractavenaatjetofAreaC cc
The value of coefficient of contraction varies from 0.61 to 0.69 depending on the shape and size of the orifice.
Coefficient of discharge Cd .
vcd CCvelocitylTheoretica
velocityActual
arealTheoretica
areaActual
eargdischlTheoretica
eargdischActualC
Average value of Cd for orifices is 0.62.
Example No. 16
Calculate the discharge in liters per second through a 5 in diameter orifice under a head of 7.6 m of water.
Assume coefficient of discharge of 0.65.
A. 78B. 1547
C. 77
D. 100
Solution:
ghCACA VQ 2
msminminQ 6781920254054
650 22 ....
sLsmQ 1006010060 3
..
1.19 PERIPHERAL VELOCITY FACTOR
gh
DN
JetVelocityof
VelocityPeripheralC d
2
2. THERMODYNAMICS
2.1 MASS AND WEIGHT
Mass (1) a property of matter that constitutes one of the fundamental physical measurements or the amount
of matter a body contains. Units of mass are in lbm, slugs, or kg. Symbol m.
Mass (2) - is the absolute quantity of matter in it, an unchanging quantity for a particular mass when the speed
of the mass is small compared to the speed of light (no relativistic effect).
Weight (1) the force acting on a body in a gravitational field, equal to the product of its mass and the
gravitational acceleration of the field. Units of weight are in lbf or N. Symbol W. Formula W = mg. Where g =
9.81 m/s2 or 32.2 ft/s2.
Weight (2) - is the force exerted by a body when its mass is accelerated in a gravitational field.
2.2 VOLUME
-
8/21/2019 LECTURE 5 cor 1
14/44
14
Volume the amount of space occupied by, or contained in a body and is measured by the number of cubes a
body contains. Units of volume are in ft3, gallons, liters, cm3, or m3. Symbol is V.
2.3 SPECIFIC VOLUME AND DENSITY
Density () of any substance is its mass (not weight) per unit volume. Units of density are lbm/ft3 or kg/m3
Symbol.
V
m
Specific Volume is the total volume of a substance divided by the total mass of a substance. Units of specific
volume are in ft3/lbm or m3/kg. Symbol is v.
m
Vv or
1v
Specific Weight () of any substance is the force of gravity on unit volume. Units of specific weight are ft3/lbfo
m3/N. Symbol is.
W
V or
gv
1
Specific Gravity (1) is a measure of the relative density of a substance as compared to the density of water at a
standard temperature. Symbol is SG.
Specific Gravity (2) a dimensionless parameter, it is defined as the ratio of the density (or specific weight) of a
substance to some standard density (or specific weight).
For Liquid substances:
stdatstdatSG
OH
l iquid
OH
l iquid
22
For Gaseous substances:
stdatstdatSG
air
gas
air
gas
Example No. 17
An iron block weighs 5 N and has a volume of 200 cm3. What is the density of the block?
A. 988 kg/cu. m.
B. 1255 kg/cu. m.
C. 2550 kg/cu. m.
D. 800 kg/cu. m.
Solution:
3
2
3
3
4.2548
81.9100
1200
5mkg
smcm
mcm
N
Vg
W
Example No. 18
Suppose two liquids of different densities, 1 = 1500 kg/m3 and2 = 500 kg/m3, were poured together inside a
100-L tank, filling it. If the resulting mixture density is 800 kg/m3, find the respective liquid amounts, in kg?
A. 35,45
-
8/21/2019 LECTURE 5 cor 1
15/44
15
B. 53,54
C. 71,63
D. 89,72
Solution:
3
3
3
2
2
1
1 Vmmm
321 mmm
33321 Vmmm 80100800
21 .mm
12 80 mm
1005001500
21 . mm
100500
80
1500
11 .
mm
15080311
mm
kgm 451
kgm 3545802 Masses = 35 kg and 45 kg
2.4 STANDARD DENSITIES
Density of water
At approx. 4oC (39.2oF) pure water has it's highest density (weight or mass) = 1000 kg/m3 or 62.4 lb/ft3.
Density of air
At 70 F (21.1 C) and 14.696 psia (101.325 kPaa), dry air has a density of 0.074887 lbm/ft3 (1.2 kg/m3).
2.5 PRESSURE
Pressure is a measure of the force exerted per unit area on the boundaries of a substance (or system). It is
caused by the collisions of the molecules of the substance with the boundaries of the system. Units of pressure
are psi, kg/cm2, kN/m2 or kPa. Symbol is p. Formula p = F/A.
2.6 ATMOSPHERIC PRESSURE
Atmospheric pressure - is the force per unit area exerted against a surface by the weight of air above that
surface in the Earth's atmosphere.
The standard atmosphere (symbol: atm) - is a unit of pressure and is defined as being equal to 101.325 kPa.[1
The following units are equivalent, but only to the number of decimal places displayed: 760 mmHg (torr), 29.92
inHg, 14.696 psi.
Barometric pressure - is often also referred to as atmospheric pressure. Units is normally in Bar. 1 Bar = 100
kPaa.
Air pressure above sea level can be calculated as p = 101325(1 - 2.25577x10-5h)5.25588, where p = air pressure (Pa
and h = altitude above sea level (m).
Also
ohh
o epp
where:
p = atmospheric pressure, (measured in bars)
-
8/21/2019 LECTURE 5 cor 1
16/44
16
h = height (altitude), km
p0 = is pressure at height h = 0 (surface pressure) = 1.0 Bar (Earth)
h0 = scale height = 7 km (Earth)
Or for every 1,000 feet, there is a corresponding pressure decrease of approximately 1 in Hg.
2.7 ABSOLUTE AND GAUGE PRESSURES
Absolute pressure, pabs - is measured relative to the absolute zero pressure - the pressure that would occur at
absolute vacuum. All calculation involving the gas laws requires pressure (and temperature) to be in absolute
units. It the sum of the gauge and atmospheric pressure.
Gauge pressure - the amount by which the total absolute pressure exceeds the ambient atmospheric pressure.
Formula pabs = patm + pg
Vacuum pressure (negative gauge pressure) - the amount by which the total absolute pressure is less than the
ambient atmospheric pressure.
Formula pabs = patm pv
Pressure gauge - is often used to measure the pressure difference between a system and the surrounding
atmosphere.
Example No. 19
A condenser vacuum gage reads 715 mm Hg when the barometer stands 757 mm Hg. State the absolute
pressure in the condenser in kN/m2.
A. 5.6 kN/m2
B. 5.9 kN/m2
C. 6.5 kN/m2
D. 5.2 kN/m2
Solution:
vacatma ppp
-
8/21/2019 LECTURE 5 cor 1
17/44
17
Hgmmpa 42715757
2
2
65760
32510142 mkN
Hgmm
mkNHgmmpa .
.
Example No. 20
With a normal barometric pressure at sea level, atmospheric pressure at an elevation of 4000 ft is nearest to,
A. 26 in Hg
B. 27 in Hg
C. 28 in Hg
D. 29 in Hg
Solution:
A drop of 1 in Hg per 1000 ft
ftft
HginHginp 4000
1000
019229
..
Hginp 9225.
2.8 TEMPERATURE
Temperature is a measure of the molecular activity of a substance. It is a relative measure of how hot o
cold a substance is and can be used to predict the direction of heat transfer. It is an intensive property that is a
measure of the intensity of the stored molecular energy in a system.
Temperature Scales:
a. Fahrenheit (F) Scale 180 units from 32 F to 212 F.
b. Celsius (C) Scale or Centigrade Scale 100 units from 0 C to 100 C.
Relationship:
CF
5
932
9
532FC
Absolute zero - is the theoretical temperature at which entropy reaches its minimum value. The laws o
thermodynamics state that absolute zero cannot be reached using only thermodynamic means.
Absolute temperature - is the temperature measured relative to the absolute zero.
Absolute Temperature Scales:
a. Kelvin (K) Scale the absolute temperature scale that corresponds to the Celsius scale.
b. Rankine (R) Scale the absolute temperature scale that corresponds to the Fahrenheit scale.
Relationship:
460 FR
273 CK
* KK 15.273273
* RR 67.459460
Temperature Change:
RFKC
9
5
9
5
-
8/21/2019 LECTURE 5 cor 1
18/44
18
KCRF
5
9
5
9
Ice point the temperature of a mixture of ice and air-saturated water at 1 atm = 0 C or 32 F.
Steam (boiling) point the temperature pure liquid water in contact with its vapour at 1 atm = 100 C or 212 F.
Triple point - The temperature and pressure at which a substance can exist in equilibrium in the liquid, solid, and
gaseous states. The triple point of pure water is at 0.01 degrees Celsius and 4.58 millimeters of mercury and is
used to calibrate thermometers.
2.9 ENERGY
Energy - is defined as the capacity of a system to perform work or produce heat.
Stored Energy otherwise known as possessed energy, it is the energy that is retrieved and stored within the
system; thus, dependent upon the mass flow.
Potential Energy (1) is defined as the energy of position. Symbol is P.E.
Potential Energy (2) energy due to the elevation and position of the system
cg
mgzPE
where m = mass (lbm, kg)
z = height above some reference level (ft, m)
g = acceleration due to gravity (ft/sec2, m/s2)
cg = gravitational constant.
=2
sec17.32 lbflbmft
= Nsmkg 21
Kinetic Energy (1) is the kinetic energy of motion. Symbol is K.E.
Kinetic Energy (2) energy or stored capacity for performing work; possessed by a moving body, by virtue of its
momentum.
cg
mvKE
2
2
where m = mass (lbm, kg)
v = velocity (ft/s, m/s)
g = acceleration due to gravity (ft/sec2, m/s2)
cg = gravitational constant.
=2
sec17.32 lbflbmft
= Nsmkg 2
1Joules Constant J 778 ft-lbf/ Btu
Internal Energy (1) is a microscopic forms of energy including those due to the rotation, vibration, translation
and interactions among the molecules of a substance.
Internal Energy (2) heat energy due to the movement of the molecules within the substance brought about its
temperature.
-
8/21/2019 LECTURE 5 cor 1
19/44
19
Internal Energy (3) energy stored within a body or substance by virtue of the activity and configuration of its
molecules and the vibration of the atoms within the molecules.
Specific Internal Energy is the substance internal energy per unit mass. Unit is Btu/lbm or kJ/kg. Symbol is u.
P-V Energy is also called flow energy or flow work.
Specific P-V Energy is the substance P-V energy per unit mass.
Enthalpy (1) is the amount of energy possessed by a thermodynamic system for transfer between itself and itsenvironment. It is equal to PVUH .Enthalpy (2) the sum of the internal energy of a body and the product of pressure and specific volume. Unit is
Btu/lbm or kJ/kg. Symbol is h.
Specific Enthalpy is defines as Pvuh .
where u = specific internal energy
P = pressure
v = specific volume
Chemical Energy stored energy that is released or absorbed during chemical reactions.
Nuclear Energy energy due to the cohesive forces of the protons and neutrons within the atoms.
Example No. 21
A high velocity flow of gas at 800 ft/sec possesses kinetic energy nearest to which of the following?
A. 1.03 Btu/lb
B. 9.95 Btu/lb
C. 4.10 Btu/lb
D. 12.8 Btu/lb
Solution:
lbftVg
WKE
889937800
232
1
2
1
2
22 ..
lbBtuBtulbft
lblbftKE 7712
16778
889937.
.
.
(D)
2.10 HEAT AND WORK
Transitory Energy otherwise known as energy in transit or in motion; energy that loses its identity once it is
absorbed or rejected within the system; independent of mass flow stream.
Heat (1) - is the transfer of energy that occurs at the molecular level as a result of a temperature difference
Symbol Q. Unit is Btu, Btu/hr, kJ or kW.
Heat (2) energy in transition between a system and its surroundings because of a difference in temperature.
Q is positive (+) when heat is added to the body
Q is negative (-) when heat is rejected by the body
Heat transferred per unit mass =m
Qq
-
8/21/2019 LECTURE 5 cor 1
20/44
20
Work is defined for mechanical system as the action of a force on an object through a distance. Symbol is W
Unit is ft-lb, kJ.
FdWWhere F = force (lbf, N)
d = displacement (ft, m )
Work is a process done by or on a system.
Power is the rate of doing work. Unit is hp or kW.
Time
WorkPower
2.11 SPECIFIC HEAT
Heat Capacity is the ratio of the heat (Q) added to or removed from a substance to the change in temperature
( T ).Specific Heat (1) is the heat capacity of a substance per unit mass. Unit is Btu/lbm-F or Btu/kg-C.
Specific Heat (2) is the heat required to raise the temperature of unit mass of a substance by a unit
temperature.
Specific heat at constant pressure is the change of enthalpy for a unit mass between two equilibrium states athe same pressure per degree change of temperature.
T
QC p
Tm
Qc p
T
qc p
Specific heat at constant volume is the change of internal energy for a unit mass per degree change o
temperature when the end states are equilibrium states of the same volume.
TQCv
Tm
Qcv
T
qcv
Specific heat ratio
u
h
c
ck
v
p
2.12 ENTROPY
Entropy (1) is a measure of inability to do work for a given heat transferred.
Entropy (2) is a measure of randomness of the molecules of a substance or measures the fraction of the tota
energy of a system that is not available for doing work.
Entropy (3) a property used to measure the state of disorder of a substance; a function of both heat and
temperature.
Entropy production is the increase in entropy.
-
8/21/2019 LECTURE 5 cor 1
21/44
21
absT
QS
absT
qs
S = the change in entropy of a system during some process (Btu/R or kJ/K).
Q = the amount of heat transferred to or from the system during the process (Btu or kJ)
absT = the absolute temperature at which the heat was transferred (R or K).
s = the change in specific entropy of a system during some process (Btu/lbm-oR or kJ/kg.K).q = the amount of heat transferred to or from the system during the process (Btu/lbm or kJ/kg).
2.13 LAWS OF THERMODYNAMICS
a. ZEROTH LAW OF THERMODYNAMICS TEMPERATURE (THERMAL EQUILIBRIUM)
- states that when each of two systems is in equilibrium with a third, the first two systems must be in
equilibrium with each other. This shared property of equilibrium is the temperature.
- states that when two bodies have equality of temperature with a third body, they in turn have equalityof temperature with each other and the three bodies are said to be in thermal equilibrium. The third
body is usually a thermometer.
b. FIRST LAW OF THERMODYNAMICS LAW ON CONSERVATION OF ENERGY
- states that, because energy cannot be created or destroyed [setting aside the later ramifications of the
equivalence of mass and energy (Nuclear Energy)] the amount of heat transferred into a system plus
the amount of work done on the system must result in a corresponding increase of internal energy in
the system. Heat and work are mechanisms by which systems exchange energy with one another.
- states that during any cycle a system undergoes, the cyclic integral of heat is proportional to the cyclic
integral of work or for any system, total energy entering = total energy leaving.
c. SECOND LAW OF THERMODYMANICS ENTROPY
- states that the entropy that is, the disorder of an isolated system can never decrease. Thus, when an
isolated system achieved a configuration of maximum entropy, it can no longer undergo change: It has
reached equilibrium.
Significant statements:
- Clausius: It is impossible for a self-acting machine unaided by an external agency to move heat from
one body to another at a higher temperature.
- Kelvin-Planck: It is impossible to construct a heat engine which, while operating in a cycle produces
no effects except to do work and exchange heat with a single reservoir.- All spontaneous processes result in a more probable state
- The entropy of an isolated system never decreases.
- No actual or ideal heat engine operating in cycles can convert into work all the heat supplied to the
working substance.
- Caratheodory: In the vicinity of any particular state 2 of a system, there exist neighboring states 1
that are inaccessible via an adiabatic change from state 2.
-
8/21/2019 LECTURE 5 cor 1
22/44
22
d. THIRD LAW OF THERMODYNAMICS - ABSOLUTE TEMPERATURE
- states that absolute zero cannot be attained by any procedure in a finite number of steps. Absolute zero
can be approached arbitrarily closely, but it can never be reached.
- The entropy of a substance of absolute temperature is zero.
2.14 CONSERVATION OF MASS
The law of conservation of mass states that the mass is indestructible.
Steady State is that circumstance in which there is no accumulation of mass or energy within the controvolume, and the properties at any point within the system are independent of time.
Continuity Equation of Steady Flow
2
22
1
11222111
v
A
v
AAAm
Usual English units are: fps, lb/ft3, ft3/lb, A ft2, m lb/sec.
Example No. 22
A fluid moves in a steady-flow manner between two sections in the same flow line. At section (1): A1 = 0.10 m2
V1 = 6 m/s, v1 = 0.33 m3/kg. At section (2): A2 = 0.20 m
2, 2 = 0.27 kg/m3. Calculate for the velocity of flow at
section (2).
A. 33.67
B. 37.63
C. 41.59
D. 45.55
Solution:
222111 VAVA
222
1
11 VAVA
2200270
330
6100V..
.
.
smV 67332
.
2.15 HELMHOLTZ FUNCTION
Helmholtz function - a thermodynamic property of a system equal to the difference between its internal energy
and the product of its temperature and its entropy. Symbol A. Formula A = u Ts.
2.16 GIBBS FUNCTION
Gibbs function - a thermodynamic property of a system equal to the difference between its enthalpy and the
product of its temperature and its entropy. It is usually measured in joules. Symbol G. Formula G = h Ts.
Example No. 23
Water is being heated by the exhaust gases from a gas turbine. The gases leave the gas turbine at 648 C and may
be cooled to 148 C. The water enters the heater at 93 C. The rate of gas flow is 25 kg/s and the water flow is
-
8/21/2019 LECTURE 5 cor 1
23/44
23
31.5 kg/s. Assume that the mean specific heat of the gas and water are respectively 1.088 and 4.27 kJ/kg-C
What is the available energy removed from the hot gases in kw? Take available sink temperature as 311 K.
A. 8345.6
B. 4862.5
C. 6041.6
D. 6977.9
Solution:
gogg STQA
b
a poba pg
T
TmcTTTmcA ln
KTa 921273648
KTa 421273148
KTa 311
421
921ln088.125311421921088.125 gA
kWAg 9.977,61.622,6600,13
2.17 BOYLES LAW
Boyles Law (1) states that if the temperature of a given quantity of gas is held constant, the volume of gas
varies inversely with the absolute pressure during a quasistatic change of state.
Boyles Law (2) states that the volume of a gas varies inversely with its absolute pressure during change of
state if the temperature is held constant.
2211 VpVp
Example No. 24
An ideal gas is contained in a vessel of unknown volume at a pressure of 1 atmosphere. The gas is released andallowed to expand into a previously evacuated bulb whose volume is 0.500 liter. Once equilibrium has been
reached, the temperature remains the same while the pressure is recorded as 500 millimeters of mercury. What
is the unknown volume, V, of the first bulb?
A. 1.069 liter
B. 0.853 liter
C. 0.961 liter
D. 1.077 liter
Solution: 1 atm = 760 mm Hg
2211 VpVp LVV 50.0500760 11
LV 961.01
2.18 CHARLES LAW
Charles Law (1) the volume of a gas varies directly as the absolute temperature during a change of state if the
pressure of the gas is held constant.
2
2
1
1
T
V
T
V
-
8/21/2019 LECTURE 5 cor 1
24/44
24
Charles Law (2) the pressure of a gas varies directly as the absolute temperature during a change of state if
the volume of the gas is held constant in.
2
2
1
1
T
p
T
p
Example No. 25
A closed vessel contains air at a pressure of 200 kN/m 2 gauge and a temperature of 32 C. The air is heated to 60
C with the atmospheric pressure of 750 mm Hg. What is the final gauge pressure?
A. 337.54
B. 127.54
C. 227.54
D. 427.54
Solution:
kPammHgPatm 100750
2
2
1
1
T
p
T
p
2736027332
1002002
p
kPagabskPap 54227543272
.. (C)
2.19 IDEAL GAS LAW
Ideal Gas Law - The equation of state of an ideal gas which is a good approximation to real gases at sufficiently
high temperatures and low pressures; that is, PV = RT, where P is the pressure, V is the volume per mole of gas
T is the temperature, and R is the gas constant.
mRTpV
2
22
1
11
T
Vp
T
Vp
where p = pressure, V = volume, m = mass, R = ideal gas constant, and T = absolute temperature.
Example No. 26
A volume of 400 cc of air is measured at a pressure of 740 mm Hg abs and a temperature of 18 C. What will be
the volume at 760 mm Hg abs and 0 C.
A. 376 cc
B. 326 cc
C. 356 cc
D. 366 cc
Solution:
1
11
2
22
T
Vp
T
Vp
27318
400740
2730
7602
V
ccV 43652
.
2.20 BASIC PROPERTIES OF IDEAL GAS
-
8/21/2019 LECTURE 5 cor 1
25/44
25
KkgkJM
R 3143.8
or RlblbftM
R 1545
Rcc vp
kc
c
v
p
1
k
kRc p
1
k
Rcv
where:
R = gas constant
M = molecular weight
c p = specific heat at constant pressure
cv = specific heat at constant volume
k = specific heat ratio
Example No. 27
A 0.90 m3 tank contains 6.5 kg of an ideal gas. The gas has a molecular weight of 44 and is at 21 C. What is the
pressure of the gas?
A. 201.3 kPa
B. 301.3 kPa
C. 401.3 kPa
D. 501.3 kPa
Solution:
KkgJkmolkg
KkmolJ
M
RR
189
44
38314.
KT 29427321
kPaPaV
mRTp 340130040190
29418956 .,.
.
2.21 PROPERTIES OF AIR
airmoleairkgM 97.28
4.1kKkgkJRlblbftR 287.03.53
CkgkJCkgkcalRlbBtuc p 0.124.024.0
CkgkJCkgkcalRlbBtuc v 716.0171.0171.0
2.22 AVOGADROS LAW AND NUMBER
Avogadros Law states that equal volumes of all ideal gases at a particular pressure and temperature contains
the same number of molecules.
Avogadros number, NA is the number of molecules in a mole of any substance and is equal to 6.0225 x 102
gmole-1.
2.23 JOULES LAW
-
8/21/2019 LECTURE 5 cor 1
26/44
26
Joules Law states that the change of internal energy of an ideal gas is a function of only the temperature
change.
2.24 DALTONS LAW OF PARTIAL PRESSURE
Daltons Law of Partial Pressure states that the total pressure pm of a mixture of gases is the sum of the
pressures that each gas would exert were it to occupy the vessel alone at the volume V m and temperature tm of
the mixture.
i
icbam ppppp
cbamcbam VVVVTTTT
mii pXp
1i
iX
Example No. 28
A mixture is formed at 689.48 kPaa, 37.8 C by bringing together these gases each volume before mixing
measured at 689.48 kPaa, 37.8 C: 3 mol CO2, 2 mol N2, 4.5 mol O2. Find the partial pressure of the CO2 afte
mixing.
A. 73 kPaa
B. 327 kPaa
C. 145 kPaa
D. 218 kPaa
Solution:
kPaapCO 73217486895423
3
2..
.
2.25 AMAGATS LAW OF PARTIAL VOLUMES
Amagat's Law of Partial Volumes - states that the volume Vm of a gas mixture is equal to the sum of volumes Vi o
the K component gases, if the temperature T and the pressure p remain the same.
i
icbam VVVVV
cbamcbam ppppTTTT
mii VXV
1i
iX
2.26 THERMODYNAMIC SYSTEMS AND PROCESSES
Thermodynamic Process is the path of the succession of states through which the system passes.
Cyclic Process or Cycle is a process where a system in a given initial state goes through a number of different
changes in state (going through various processes) and finally returns to its initial values.
Reversible Process is defined as a process that, once having taken place, can be reversed, and in so doing
leaves no change in either the system or surroundings.
Irreversible Process is a process that cannot return both the system and the surroundings to their origina
conditions. That is, the system and the surroundings would not return to their original conditions if the process
was reversed.
Adiabatic Process is one in which there is no heat transfer into or out of the system. The system can be
considered to be perfectly insulated.
-
8/21/2019 LECTURE 5 cor 1
27/44
27
Isentropic Process is one in which the entropy of the fluid remains constant. This will be true if the process the
system goes through is reversible and adiabatic. An isentropic process can also be called a constant entropy
process.
Polytropic Process is a process when a gas undergoes a reversible process in which there is heat transfer, the
process frequently takes place in such a manner that a plot of the Log P (pressure) vs Log V (volume) is a straight
line. Or stated in equation form nPV = a constant.
Throttling Process is defined as a process in which there is no change in enthalpy from state one to state two
21 hh ; no work is done, 0W ; and the process is adiabatic, 0Q .Isobaric Process is an internally reversible (quasistatic, if nonflow) process of a pure substance during which
the pressure remains constant.
Isometric Process (Isochoric Process) a constant volume process that is internally reversible (quasi-static if
nonflow), involving a pure substance.
Isothermal Process is an internally reversible (quasistatic, if nonflow) constant temperature process of a pure
substance.
2.27 EQUATIONS FOR THERMODYNAMIC PROCESSES
Entropy = T
dQS
Non-Flow Equation
nfWUQ
Steady-Flow Equation, 0K 0P
sfWHQ
Steady-Flow Equation, 0K 0P
sf WPKHQ
where:
U = internal energy
H = enthalpyK = kinetic energyP = potential energy
nfW = non-flow work
sfW = steady flow work
Internal Energy
TmcU v
Enthalpy
TmcH p
Non-Flow Work
pdVWnfSteady Flow Work, 0K 0P
VdpWsfSteady-Flow Equation, 0K 0P
VdpWPK sf
-
8/21/2019 LECTURE 5 cor 1
28/44
28
Note:U
Hk
Example No. 29
In compressing 20 kg/min of air, its enthalpy was increased by 140 kJ/kg. If the power input is 50 kW, the heat
transfer in kW is,
A. 3.33
B. -3.33C. 6.67
D. -6.67
Solution:
WHQ
secminmin 60120140 kgkgkJH
kWH 6746.
kWW 50
kWQ 333506746 ..
Example No. 30
What is the temperature rise in water dropping at a height of 200 ft in F?
A. 0.257
B. 1.33
C. 2.25
D. 6.67
Solution:
J
WHtWc p
pJcHt
FlbBtuBtulbftft
t
0116778
200
..
Ft 2570.
Example No. 31
A non-flow system contains 1 lb of an ideal gas (cp = 0.24, cv = 0.17, both in Btu/lb-R). The gas temperature is
increased by 10 F while 5 Btu of work are done by the gas. What is the heat transfer in Btu?
A. -3.3
B. -2.6C. +6.7
D. +7.4
Solution:
WUQ BtuTmcU v 71101701 ..
BtuW 5BtuQ 76571 ..
-
8/21/2019 LECTURE 5 cor 1
29/44
29
2.28 ISOBARIC PROCESS
Isobaric Process is an internally reversible (quasistatic, if nonflow) process of a pure substance during which
the pressure remains constant.
p = Constant
1
2
1
2
T
T
V
V
12 TTmcH p
12 TTmcU v
Non-flow: nfWUQ
12 VVppdVWnf HQ
Entropy: T
dQS
2
1
1
2 lnlnV
Vmc
T
TmcS pp
Steady Flow: sfWHQ
0 VdpWsfHQ
Entropy: T
dQS
2
1
1
2 lnlnV
Vmc
T
TmcS pp
Specific Heat Ratio:
U
Q
U
Hk
-
8/21/2019 LECTURE 5 cor 1
30/44
30
2.29 ISOMETRIC PROCESS (ISOCHORIC PROCESS)
Isometric Process (Isochoric Process) a constant volume process that is internally reversible (quasi-static if
nonflow), involving a pure substance.
V = constant
1
2
1
2
T
T
p
p
12 TTmcH p
12 TTmcU v
Non-flow: nfWUQ
0 pdVWnf
UQ
Entropy: T
dQS
1
2
1
2 lnlnp
pmc
T
TmcS vv
Steady Flow: sfWHQ
12 ppVVdpWsf UQ
Specific Heat Ratio:
Q
H
U
H
k
Example No. 32
One kg of hydrogen are cooled from 450 C to 320 C in a constant volume process. The specific heat at constant
volume, cv, is 10.2 kJ/kg-K. How much heat is removed?
A. 1136 kJ
B. 1326 kJ
C. 1623 kJ
-
8/21/2019 LECTURE 5 cor 1
31/44
31
D. 2136 kJ
Solution:
12
TTmcQ v kJQ 132632045021001 ..
2.30 ISOTHERMAL PROCESS
Isothermal Process is an internally reversible (quasistatic, if nonflow) constant temperature process of a pure
substance.
pV = constant, T = constant
12 TTmcH p
12 TTmcU v
Non-Flow Equation: nfWUQ
mRTCpVVpVp 2211
2
1
1
2
p
ppV
V
VpVWnf lnln
2
1
1
2 lnlnp
pmRT
V
VmRTWnf
nfWQ
Steady Flow: sfWHQ
2
1
1
2 lnlnp
ppV
V
VpVWs f
2
1
1
2 lnlnp
pmRT
V
VmRTWs f
sfWQ
Entropy:
1
2lnV
VmRS
-
8/21/2019 LECTURE 5 cor 1
32/44
32
2
1lnp
pmRS
2
1
1
2 lnlnp
p
T
pV
V
V
T
pVS
Example No. 33
Five kmols of air initially at one atmosphere and 299 K are compressed isothermally to 8 atmospheres. How
much total heat is removed during the compression?A. 25,846.3 kJ
B. 28,922.9 kJ
C. 39,345.6 kJ
D. 44,680.9 kJ
Solution:
2
1
p
pnRTQ ln
atm
atmK
Kkmol
kJkmolQ
8
129931485 ln.
kJQ 2784625 ., (A)
2.31 ISENTROPIC PROCESS
Isentropic Process is a reversible adiabatic process with constant entropy.
kpV = constant, 0S , mRTpV , 0Q
k
V
V
p
p
2
1
1
2
,
1
2
1
1
2
k
V
V
T
T
,
Ork
k
p
p
T
T
1
1
2
1
2
12 TTmcH p 12 TTmcU v
Non-flow: nfWUQ
11
11
1
2
111
1
1
211
k k
nf p
p
k
Vp
V
V
k
VpW
-
8/21/2019 LECTURE 5 cor 1
33/44
33
11
11
11
1
1
21
1
2
11
1
1
21 k
k k k
nf p
p
k
mRT
V
V
k
mRT
V
V
k
mRTW
k
VpVp
k
TTmR
T
T
k
mRTWnf
111
1
112212
1
21
But,
1
kRcv
UTTmcW vnf 12
Steady Flow: sfWHQ
11
11
11
11 1
21
1
2
11
1
1
21
1
1
211
T
T
k
kmRT
V
V
k
kmRT
p
p
k
kmRT
p
p
k
VkpW
k k
k
k
k
s f
k
TTkmRWsf
1
12
But
1
k
kRc p
HTTmcW psf 12Note:
nf
sf
v
p
W
W
pdV
Vdp
U
H
c
ck
Example No. 34
Air is compressed in a diesel engine from an initial pressure of 13 psia and a temperature of 120 F to one-twelfthof its initial volume. Calculate the final temperature assuming the compression to be adiabatic.
A. 1110 F
B. 980 F
C. 987 F
D. 1560 F
Solution:1
2
1
1
2
k
V
V
T
T
141
1
12
12
1460120
460
.
V
Vt
Ft 1111072
.
Example No. 35
Nitrogen is expanded isentropically. The temperature change from 620 F to 60 F. If the pressure ratio, p1/p2 = 13
what is the isentropic index.
-
8/21/2019 LECTURE 5 cor 1
34/44
34
A. 1.26
B. 1.2
C. 1.4
D. 1.46
Solution:
k
k
p
p
T
T
1
2
1
2
1
kk 1
1346060
460620
kk 1
130772
.
131
0772 ln.lnk
k
28501
.
k
k
41.k
2.32 POLYTROPIC PROCESS
Polytropic Process is an internally reversible process during which pVn = C where n is any constant.
npV = constant, mRTpV
1
2
1
1
2
n
V
V
T
T
,
n
n
p
p
T
T
1
1
2
1
2
12 TTmcH p
12 TTmcU v
Non-flow Work: nfWUQ
11
11
1
2
111
1
1
211
nn
nf p
p
n
Vp
V
V
n
VpW
-
8/21/2019 LECTURE 5 cor 1
35/44
35
11
11
11
1
1
21
1
2
11
1
1
21 n
nnn
nf p
p
n
mRT
V
V
n
mRT
V
V
n
mRTW
n
VpVp
n
TTmR
T
T
n
mRTWnf
111
1
112212
1
21
But,
1
kRcv
11
112212
k
VpVp
k
TTmRU
1111
1
1
1
1
1
1 112211221122
nk
VpVpknVpVp
nkVpVp
nkQ
Steady Flow: sfWHQ
11
11
11
11 1
21
1
2
11
1
1
21
1
1
211
T
T
n
nmRT
V
V
n
nmRT
p
p
n
nmRT
p
p
n
VnpW
nn
n
n
n
s f
n
TTnmRWsf
1
12
But
1
k
kRc p
11
11221212
k
VpVpk
k
TTkmRTTmcH p
11221122111
1
1
1VpVp
n
n
k
kVpVp
nkQ
11
1122
nk
VpVpknQ
Entropy:
1
2ln1 T
T
n
knmcS v
Or
2
1lnV
VknmcS v
1
2
1
1
2 lnln1 p
p
n
knmc
p
p
n
knmcS v
n
n
v
Note:
Steady flow work:
VdpPKWsf
-
8/21/2019 LECTURE 5 cor 1
36/44
36
2.33 CURVES FOR DIFFERENT VALUES OF n.
2.34 TABLE OF IDEAL GAS FORMULAS
Ideal Gas Formulas
For constant mass systems undergoing internally reversible processes
Process
Isometric
CVIsobaric
CpIsothermal
CTIsentropic
CS
Polytropic
CpVn
p, V, T
relations 1
2
1
2
p
p
T
T
1
2
1
2
V
V
T
T
2211 VpVp
kkVpVp
21 21
1
2
1
1
2
k
V
V
T
T
kk
p
p
T
T1
1
2
1
2
nnVpVp
21 21
1
2
1
1
2
n
V
V
T
T
nn
p
p
T
T1
1
2
1
2
2
1
pdV 0 12 VVp 1
2
11 ln
V
VVp
k
VpVp
1
1122
n
VpVp
1
1122
2
1
Vdp 12 ppV 01
2
11 ln
V
VVp
k
VpVpk
1
1122
n
VpVpn
1
1122
12 UU dTcm v
12
TTmcv dTcm v
12 TTmcv
0 dTcm v
12 TTmcv
dTcm v
12 TTmcv
Q dTcm v
12 TTmcv
dTcm p
12 TTmcp
Tdsm
1
2
11 ln
V
VVp
0 dTcm n
12 TTmcn
n 0 1 k to
Specific heat, c vc pc 0
n
nkcc vn
1
Ck
-
8/21/2019 LECTURE 5 cor 1
37/44
37
12 HH dTcm p
12 TTmcp
dTcm p
12 TTmcp 0 dTcm p
12 TTmcp
dTcm p
12 TTmcp
12 SS
TdTc
m v
1
2ln
T
Tmcv
TdTc
m p
1
2lnT
Tmcp
T
Q
1
2lnV
VmR
0 T
dTcm n
1
2lnT
Tmcn
1
2lnV
V
mRT
dTc
m
v
, 12
lnp
p
mRT
dTc
m
p
Example No. 36
After a series of state changes, the pressure and volume of 2.268 kg of nitrogen are each doubled. What isS? c=0.7442 kJ/kg-K, cp = 1.0414 kJ/kg-K.
A. 2.8 kJ/kg-K
B. 1.24 kJ/K
C. 2.8 kJ/K
D. 1.24 kJ/kg-K
Solution:
1
2
1
2
V
VmR
T
TmcS v lnln
1
2
1
2
p
pmc
V
VmcS v p lnln
KkJp
p
V
VS 8072
274420
2041412682
1
1
1
1 .ln.ln..
2.35 STAGNATION PROPERTIES
Stagnation Properties are those thermodynamic properties that a moving stream of compressible fluid would
have if it were brought to rest isentropically (no outside work, the kinetic energy brings about the compression).
Stagnation enthalpy
Jg
vhh
c2
2
0
Stagnation temperature
pc Jcg
vTT
2
2
0
TJcg
v
p
p
T
T
pc
k
k
21
21
00
2.36 MACH NUMBER
Mach Number is the ratio of the actual speed divided by the local speed of sound a in the fluid.
a
M 1M 1M
[SUBSONIC] [SUPERSONIC]
Acoustic speed:
21
kRTga c
-
8/21/2019 LECTURE 5 cor 1
38/44
38
2.37 MOLLIER DIAGRAM
Mollier Diagram (h-s) is a chart on which enthalpy is the ordinate and entropy the abscissa.
2.38 TEMPERATURE-ENTROPY DIAGRAM
-
8/21/2019 LECTURE 5 cor 1
39/44
39
2.39 ph-Chart
2.40 MIXTURES
Mixture substance made up of liquid and vapor portion or two-phase liquid-vapour system.
x= quality or dryness factor or vapour content
y = 1 x = moisture content or wetness
Properties of mixtures
fgf xvvv
-
8/21/2019 LECTURE 5 cor 1
40/44
40
fgf xuuu
fgf xhhh
fgf xsss
2.41 PROCESSES INVOLVING PURE SUBSTANCES
a. Isobaric or constant pressure process: p1 = p2
b. Isothermal or constant temperature process: T1 = T2
Evaporation and condensation processes occur at constant pressure and constant temperature.c. Isometric or constant volume process: V1 = V2
For constant mass: v1 = v2
If the final state is a mixture: v1 = (vf+ xvfg)2
d. Isentropic or constant entropy process: s1 = s2
Isentropic process is reversible (no friction loss) and adiabatic (no heat loss, that is, completely insulated
system).
e. Throttling or isenthalpic (constant enthalpy) process: h1 = h2
If the final state is a mixture: h1 = (hf+ xhfg)2
If the initial state is a mixture, such as in steam calorimeter:
(hf+ xhfg)1 = h2
Example No. 37
After expanding 2.5 L of superheated steam at 2.5 MPaa and 400 C, its pressure was decreased to 0.01 MPaa. I
its dryness fraction is 90%, what is the final volume of the steam in L?
@ 2.5 MPaa and 400 C, v = 125.2 x 10-3 m3/kg
@ 0.01 MPaa. v f = 1.0102 x 10-3 m3/kg and vg = 14,674 x 10
-3 m3/kg.
A. 164
B. 264
C. 364
D. 464
Solution:
f g f vvxvv 2 3332 10010221106741490010010221 .,..v kgmv 332 1020613 ,
2
2
1
1
v
V
v
Vm
3
2
31020613102125
52
,.
. VL
LV 2642
Example No. 38Determine the heat transferred to the cooling fluid in a condenser operating under steady flow conditions with
steam entering with an enthalpy of 2300 kJ/kg and a velocity of 350 m/s. The condensate leaves with an
enthalpy of 160 kJ/kg and velocity of 70 m/s.
A. -2199 kJ/kg
B. -1922 kJ/kg
C. 2190 kJ/kg
D. 2910 kJ/kg
-
8/21/2019 LECTURE 5 cor 1
41/44
41
Solution:
10002
2
1
2
2
12
VVhhQ
10002
350702300160
22 Q
2.42 THE CARNOT CYCLE
3421 TTTT and 3241 SSSS
411 SSTQ A
412322 SSTSSTQR
412411 SSTSSTQQW RA
411
412411
SST
SSTSST
Q
QQ
Q
We
A
RA
A
H
LH
T
TT
T
TTe
1
21
L
R
H
A
T
Q
T
Q
where e = Carnot cycle efficiency
T1 = TH = highest absolute temperature
T2 = TL = lowest absolute temperature
Example No. 39
Carnot engine receives 130 Btu of heat from a hot reservoir at 700 F and rejects 49 Btu of heat. Calculate the
temperature of the cold reservoir.
A. -21.9 F
B. -24.2 F
C. -20.8 FD. -22.7 F
Solution:
RTH 1160460700
H
LH
A
R A
A T
TT
Q
QQ
Q
We
-
8/21/2019 LECTURE 5 cor 1
42/44
42
1160
1160
130
49130 LT
FRTL 772223437 ..
2.43 STIRLING AND ERICSSON CYCLE
Ideal Stirling Cycle is composed of two isothermal and two isometric processes, the regeneration occurring at
constant volume.
Ideal Ericsson Cycle consists of two isothermal and two isobaric processes, with the regeneration occurringduring constant pressure.
2.44 BASIC WORKING CYCLES FOR VARIOUS APPLICATIONS
Application Basic Working Cycle
Steam Power Plant Rankine Cycle
Gasoline Engine (Spark-Ignition) Otto Cycle
Diesel Engine (Combustion-Ignition) Diesel Cycle
Gas Turbine Brayton Cycle
Refrigeration System Refrigeration Cycle
Example No. 40
One kilogram of air at a pressure and temperature of 1 bar and 15 C initially, undergoes the following processes
in a cycle: isothermal compression to 2 bar; polytropic compression from 2 bar to 4 bar; isentropic expansion
from 4 bar to initial condition. What is the cycle work in kJ/kg?
A. 10.3
B. 13.0
C. 57.3
D. 70.3
Solution:
kPabarp 10011
KT 288273151
kPabarp 20022
kPabarp 40043 kgm 1
1-2, CTKTT 28812
kPabarp 20022
2-3, CpVn
-
8/21/2019 LECTURE 5 cor 1
43/44
43
kPap 2002
KT 2882
kPap 4003
n
n
p
pTT
1
2
323
3-1, CpV
k
kPap 2003KT 2881
kPap 1001
k
k
p
pTT
1
1
313
Then
k
k
n
n
p
pT
p
pTT
1
1
31
1
2
323
k
k
n
n
p
p
p
p
1
1
3
1
2
3
4.1
14.11
100
400
200
400
n
n
333.2n
2
1
121
lnV
VmRTW
11
1
3
22
32
n
n
p
p
n
nmRTW
11
1
1
3113
k
k
p
p
k
kmRTW
kgm 1
1
2
12
1
121lnln
p
pmRT
V
VmRTW
kJW 3.57100
200ln288287.0121
11
1
3
2232
n
n
p
p
n
nmRTW
-
8/21/2019 LECTURE 5 cor 1
44/44
1400
200
333.21
288287.01333.2 333.21333.2
32W
kJW 3.7032
11
1
1
3113
k
k
p
p
k
kmRTW
1100
400
4.11
288287.014.1 4.114.1
13W
kJW 6.14013
kJWWWWcyc 6.1403.703.57133221 kJWcyc 13
- End -